| Age | Commit message (Collapse) | Author |
|---|
|
SFP v3.4 supports 8 keys in SRK table which leads to corresponding
changes in OSPR key revocation field. So modify OSPR_KEY_REVOC_XXX
macros accordingly.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Delete CONFIG_SKIP_LOWLEVEL_INIT define in ls1021atwr.h and
ls1021aqds.h can let it run cpu_init_cp15 to enable i-cache. First
stage of u-boot can run faster after that. There is a description
about skip lowlevel init in board/freescale/ls1021atwr/README.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Update the API's for transition of Security Monitor states. Instead
of providing both initial and final states for transition, just
provide final state for transition as Security Monitor driver will
take care of it internally.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
[York Sun: Reformatted commit message slightly]
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
|
|
Authentication of images in Falcon Mode is not supported. Do not enable
SPL_OS_BOOT when TI_SECURE_DEVICE is enabled. This prevents attempting
to directly load kernel images which will fail, for security reasons,
on HS devices, the board is locked if a non-authenticatable image load
is attempted, so we disable attempting Falcon Mode.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
This config option seems to be unused and is probably vestigial.
Remove it.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
The config option AM33XX is used in several boards and should be
defined as a stand-alone option for this SOC. We break this out
from target boards that use this SoC and common headers then enable
AM33XX on in all the boards that used these targets to eliminate any
functional change with this patch.
This is similar to what has already been done in
9de852642cae ("arm: Kconfig: Add support for AM43xx SoC specific Kconfig")
and is done for the same reasons.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
If the ending portion of the DRAM is reserved for secure
world use, then u-boot cannot use this memory for its relocation
purposes. To prevent issues, we mark this memory as PRAM and this
prevents it from being used by u-boot at all.
Signed-off-by: Daniel Allred <d-allred@ti.com>
|
|
rockchip platform have a protocol to pass the the kernel reboot mode to bootloader
by some special registers when system reboot. In bootloader we should read it and take action.
We can only setup boot_mode in board_late_init becasue "setenv" need env setuped.
So add CONFIG_BOARD_LATE_INIT to common header and use a entry "rk_board_late_init"
to replace "board_late_init" in board file.
Signed-off-by: Jacob Chen <jacob2.chen@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
To keep it same with 3288.
Signed-off-by: Jacob Chen <jacob2.chen@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
The latest rk3288-miniarm board doesn't have eMMC device, so remove it.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Enable ums feature for rk3036 boards, so that we can mount the mmc
device to PC.
Signed-off-by: jacob2.chen <jacob2.chen@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Rock2 has been tested with back to brom feature. The tricky part is that
with this feature the default environment is inside u-boot, and it's
defined for every rk3288 board independetly. So I just changed it for
rock2 here if ROCKCHIP_SPL_BACK_TO_BROM.
Solve by moving environment after u-boot before 1M boundary
Signed-off-by: Sandy Patterson <apatterson@sightlogix.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
As boot monitor contains a mkimage header, it can be loaded at any location.
So, have a common addr_mon address across all keystone2 SoCs. And also
making sure that boot monitor is installed early during default boot to
avoid any overlapping with other images.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
On K2G, the PCIe SerDes h/w is a re-use from other K2 devices and SerDes
driver requires a firmware image to initialize the SerDes h/w device.
This is firmware is part of the initramfs file that is loaded to memory
in u-boot and passed to kernel as in other K2 platforms. This patch
customize the u-boot env to have this done automatically when the K2G EVM
boots up. With this, a user may be able to boot the EVM with a standard
PCIe card at the x1 PCIe slot and release image and test PCIe devices
such as NIC, SATA etc.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Move FASTBOOT_MBR_NAME and FASTBOOT_GPT_NAME into Kconfig.
Add dependency on the FASTBOOT_FLASH setting (also for FASTBOOT_MBR_NAME).
Remove the now redundant GPT_ENTRY_NAME.
Signed-off-by: Petr Kulhavy <brain@jikos.cz>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Steve Rae <steve.rae@raedomain.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Add FIXME about xxx_PARTITION needing to be in Kconfig]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
In both DOS and ISO partition tables the same code to create partition name
like "hda1" was repeated.
Code moved to into a new function part_set_generic_name() in part.c and optimized.
Added recognition of MMC and SD types, name is like "mmcsda1".
Signed-off-by: Petr Kulhavy <brain@jikos.cz>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Steve Rae <steve.rae@raedomain.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Add special target "mbr" (otherwise configurable via CONFIG_FASTBOOT_MBR_NAME)
to write MBR partition table.
Partitions are now searched using the generic function which finds any
partiiton by name. For MBR the partition names hda1, sda1, etc. are used.
Signed-off-by: Petr Kulhavy <brain@jikos.cz>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Steve Rae <steve.rae@raedomain.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
So far partition search by name has been supported only on the EFI partition
table. This patch extends the search to all partition tables.
Rename part_get_info_efi_by_name() to part_get_info_by_name(), move it from
part_efi.c into part.c and make it a generic function which traverses all part
drivers and searches all partitions (in the order given by the linked list).
For this a new variable struct part_driver.max_entries is added, which limits
the number of partitions searched. For EFI this was GPT_ENTRY_NUMBERS.
Similarly the limit is defined for DOS, ISO, MAC and AMIGA partition tables.
Signed-off-by: Petr Kulhavy <brain@jikos.cz>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Steve Rae <steve.rae@raedomain.com>
|
|
|
|
Signed-off-by: Tom Rini <trini@konsulko.com>
Conflicts:
include/configs/dra7xx_evm.h
|
|
Enable pie option for relocation.
Signed-off-by: rick <rick@andestech.com>
Cc: Andes <uboot@andestech.com>
|
|
Currently the controller by default enables the Receive Detect feature in P3
mode in USB 3.0 PHY. However, USB 3.0 PHY does not reliably support receive
detection in P3 mode.
Enabling the USB3 controller to configure USB in P2 mode whenever the Receive
Detect feature is required.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
|
|
The function fdt_fixup_dr_usb is specific to fsl/nxp. So,
make the function name explicit and rename fdt_fixup_dr_usb
into fsl_fdt_fixup_dr_usb.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
|
|
Since commit aa7a648747d8c704a9a81c9e493d386930724e9d
("net: Stop including NFS overhead in defragment max") the following
has been reproducibly observed while trying to transfer data over TFTP:
Load address: 0x80408000
Loading: EHCI timed out on TD - token=0x8008d80
T EHCI timed out on TD - token=0x88008d80
Rx: failed to receive: -5
This patch fixes this by lowering our TFTP block size to be within the
standard maximal de-fragmentation aka IP packet size again.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
This patch enables the SPL-DFU support for
dra7x platform.
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Adding support functions to run dfu spl commands.
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
The cmd_dfu functionality is been used by both SPL and
u-boot, saperating the core dfu functionality moving
it to common/dfu.c.
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
transfers requests
This is required for better performance, and performs below tuning:
1. Enable burst length set, and define it as 4/8/16.
2. Set burst request limit to 16 requests.
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
|
|
Since commit aa7a648747d8c704a9a81c9e493d386930724e9d
("net: Stop including NFS overhead in defragment max") the following
has been reproducibly observed while trying to transfer data over TFTP:
Load address: 0x80408000
Loading: EHCI timed out on TD - token=0x8008d80
T EHCI timed out on TD - token=0x88008d80
Rx: failed to receive: -5
This patch fixes this by upping our maximal de-fragmentation aka IP
packet size again.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
|
|
|
|
This board is getting close to or exceeding the size limit again, remove
CONFIG_AUTO_COMPLETE to save space and while in here switch to the
default and slightly less complete default baudrate table.
Cc: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
The primary benefit of this change is that it adds all missing clocks and
resets properties to peripherals. This will allow peripheral drivers to
migrate to the standard clock and reset APIs in the future.
Main changes:
* Brought in the correct Tegra210 CAR binding; the old file in U-Boot
appears to be a renamed version of the Tegra124 bindings rather than
the real Tegra210 version.
* Conversion of SPI and UART nodes to standard DMA bindings. U-Boot
doesn't use DMA so isn't affected.
* Split of EHCI and USB PHY nodes. The EHCI nodes continue to contain all
information required by U-Boot, so U-Boot is not affected.
* Conversion of many magic numbers to named defines.
* Addition of many nodes not used by U-Boot, including separation of the
Tegra LIC (Legacy IRQ controller) and GIC.
* Node sort order fixes.
Remaining deltas relative to the Linux DT:
* U-Boot has enabled PCIe for Tegra210, but the kernel hasn't yet.
* The GPIO node compatible value in the kernel explicitly includes
Tegra124 values whereas U-Boot does not. I'll send a kernel patch to
correct this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
The primary benefit of this change is that it adds all missing clocks and
resets properties to peripherals. This will allow peripheral drivers to
migrate to the standard clock and reset APIs in the future.
Main changes:
* USB phy_type property is aligned with the kernel, so board files are
updated so the final DT content doesn't change. I'm not convinved that
Nyan uses HSIC phy_type. However, I'd rather this change be a no-op,
and any DT bug-fixes be separate.
* Sync misc changes from the kernel: missing DT content, minor compatible
value fixes, typos.
Remaining deltas relative to the Linux DT:
* U-Boot uses #address-cells/#size-cells of 1 whereas the kernel uses 2.
I believe U-Boot's DT parsing currently assumes that these values match
the physical address size, so I didn't synchronize this part of the DT.
* U-Boot uses the original XUSB PHY DT binding, wherease the kernel DT
has moved to a newer version. Thus, XUSB client nodes include properties
names phys and phy-names that do not appear in the kernel, and don't
include pad definitions in the padctl node.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
The primary benefit of this change is that it adds all missing clocks and
resets properties to peripherals. This will allow peripheral drivers to
migrate to the standard clock and reset APIs in the future.
Main changes:
* Conversion of SPI nodes to standard DMA bindings. U-Boot doesn't use
DMA so isn't affected.
* Split of EHCI and USB PHY nodes. The EHCI nodes continue to contain all
information required by U-Boot, so U-Boot is not affected.
* Boards need to define the clk32k_in clock that feeds the Tegra PMC.
* Addition of tegra114-mc.h since tegra114.dtsi now includes it.
* Conversion of many magic numbers to named defines.
* Addition of many nodes not used by U-Boot.
* Node sort order fixes.
Remaining deltas relative to the Linux DT:
* USB node compatible values in U-Boot explicitly list Tegra114 values
whereas the kernel does not. I'll send a kernel patch to correct this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
The primary benefit of this change is that it adds all missing clocks and
resets properties to peripherals. This will allow peripheral drivers to
migrate to the standard clock and reset APIs in the future.
Main changes:
* Modification of PCIe memory region addresses. The HW memory layout is
programmable, so this should work fine, and Beaver PCIe was tested
without issue.
* Removal of pcie_xclk from the PCIe node and clock binding header. This
clock doesn't exist and isn't used; only a reset with this ID exists.
* Conversion of SPI nodes to standard DMA bindings. U-Boot doesn't use
DMA so isn't affected.
* Split of EHCI and USB PHY nodes. The EHCI nodes continue to contain all
information required by U-Boot, so U-Boot is not affected.
* Changed the phy_type value for the second USB port. This required board
DTs to be updated to keep the same configuration.
* Boards need to define the clk32k_in clock that feeds the Tegra PMC.
* Addition of tegra30-mc.h since tegra30.dtsi now includes it.
* Conversion of many magic numbers to named defines.
* Addition of many nodes not used by U-Boot.
* Node sort order fixes.
Remaining deltas relative to the Linux DT:
* None.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
This brings in a few minor fixes since the last sync. The largest change
is the removal of the definition for TEGRA20_CLK_PCIE_XCLK. This clock
doesn't actually exist.
Remaining deltas:
* Addition of u-boot,dm-pre-reloc property to a couple of nodes.
* Addition of the NAND controller, which Linux doesn't yet support.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
The Linux-for-Tegra kernel uses a very long command line.
The default value of CONFIG_SYS_CBSIZE is too small to printf out the
long command line and causes a message like:
bootarg overflow 602+0+0+1 > 512
on the console, and the board refuses to boot.
The default value of CONFIG_SYS_MAXARGS is too small to add a long
long command line, and the kernel won't boot without the complete
bootargs.
Increasing these two config options solves this problem.
Signed-off-by: Bryan Wu <pengw@nvidia.com>
Signed-off-by: Peter Chubb <Peter.Chubb@data61.csiro.au>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
|
|
This patch adds basic support for the Marvell Armada 7K DB-88F7040
development board. Supported are the following interfaces:
- UART
- SPI (incl. SPI NOR)
- I2C
- USB
- SATA / AHCI
Support for other interfaces will follow.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
|
|
This patch adds basic support for the Marvell Armada 3700 DB-88F3720
development board. Supported are the following interfaces:
- UART
- SPI (incl. SPI NOR)
- I2C
- Ethernet
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
|
|
This version is based on the Marvell U-Boot version with this patch
applied as latest patch:
Git ID 7f408573: "fix: comphy: cp110: add comphy initialization for usb
device mode" from 2016-07-05.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
|
|
Introduce a hidden USB_FUNCTION_DFU Kconfig option and select it for
CMD_DFU (as we must have the DFU command enabled to do anything DFU).
Make all of the entries in drivers/dfu/Kconfig depend on CMD_DFU and add
options for all of the back end choices that DFU can make use of.
Cc: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
|
|
Previously we had been adjusting CONFIG_SYS_MALLOC_LEN based on if
CONFIG_DFU_MMC has been set or not. However, for quite some time this
has not been the case as we often include <configs/ti_armv7_common.h>
prior to setting CONFIG_DFU_MMC so we would always use 16MiB and then
not have enough room for to DFU files. Given the amount of memory we
always have, setting a minimum size of 32MiB for malloc is reasonable.
However, in the SPL case not only do we not need that much we start
running into overlap problems and then will fail to boot. Since we
don't need 16MiB in the SPL case, bring this down to 8MiB.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
trini: Drop local memset() from
examples/standalone/mem_to_mem_idma2intr.c
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
move the UBI config options into Kconfig.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andrew F. Davis <afd@ti.com>
Reviewed by: Evgeni Dobrev <evgeni at studio-punkt.com>
|
|
Move this option to Kconfig and clean up existing uses.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Move this config to Kconfig option and clean up existing uses.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Calvin Johnson <calvin.johnson@nxp.com>
CC: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Instead of using multiple macros, a data structure is used to pass
board-specific parameters to MMDC DDR driver.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
