summaryrefslogtreecommitdiff
path: root/include
AgeCommit message (Collapse)Author
2019-10-13mx6: mx6sabre common: Use more conventional spelling of fdtfileSjoerd Simons
Both the distro boot configuration as well as the general pxe support standardized on fdtfile as the variable to hold the dtb filename. Adjust to follow that such that e.g. "pxe boot" will just work. Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
2019-10-13Add i.MX7D based Meerkat96 board supportShawn Guo
The Meerkat96 board, based on the NXP i.MX7D SoC, is a member of 96Boards community and complies with all Consumer Edition board specifications. https://www.novtech.com/products/meerkat96.html https://www.96boards.org/product/imx7-96/ The initial supported/tested devices include: - Debug serial - SD - USB Host (with Ethernet) With these support, it's good enough for loading Linux Kernel from SD or Ethernet over USB. Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Reviewed-by: Peng Fan <peng.fan@nxp.com> Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
2019-10-12Merge https://gitlab.denx.de/u-boot/custodians/u-boot-x86Tom Rini
- Remember the device being emulated for Sandbox PCI - Update Kconfig options for FSP 1.0 - Drop RESET_BASE and RESET_SEG_SIZE that are no longer used
2019-10-12Merge branch '2019-10-11-master-imports'Tom Rini
- Assorted cleanups - FAT bugfixes - mediatek platform updates
2019-10-11tao3530: Fix usage of mmc rescanJarkko Nikula
Currently "bootcmd" does not work as intended but instead prints MMC usage information and goes directly to "nandboot". Follow what the commit 669681104daa ("configs: Fix usage of mmc rescan") does for other boards prior to support for TechNexion TAO3530 SoM was added. Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
2019-10-11configs: ti: Use addr_fit for run_fit environment variableAndrew F. Davis
When running 'run_fit' the FIT file should have been loaded at 'addr_fit', although at this point they should be the same use this variable instead of 'loadaddr'. Signed-off-by: Andrew F. Davis <afd@ti.com>
2019-10-11am335x, guardian: adapt guardian board to DMMoses Christopher
- update partition table - remove env partitions - dts: add new interfaces (uart2, extra gpio-key) remove unneeded entries update nand timings for performance improvement - defconfig: adapt configurations to suit DM remove unneeded configs - am335x_guardian.h: remove mmc boot Signed-off-by: Moses Christopher <BollavarapuMoses.Christopher@in.bosch.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2019-10-11arm: dts: split mtk-reset.h into per-chip headerRyder Lee
This follows the linux header rules to avoid conflict bitfields. Tested-by: Frank Wunderlich <frank-w@public-files.de> Signed-off-by: Ryder Lee <ryder.lee@mediatek.com> Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
2019-10-11waitbit: Add the generic wait_for_bit macros for 16 and 32 bits.Kursad Oney
wait_for_bit_le32 and wait_for_bit_le16 use the raw I/O functions which would default to big-endian on BE systems. Create the generic equivalents to use the native endianness. Signed-off-by: Kursad Oney <kursad.oney@broadcom.com> Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com> Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2019-10-11env: ti: am65x_evm: Add env support to boot the MCU R5F rprocsSuman Anna
Add support to boot the MCU domain R5F Core0 remoteproc at U-boot prompt on the AM65x EVM boards by using the 'boot_rprocs' and other env variables defined in the common environment file k3_rproc.h, and updating the 'DEFAULT_RPROCS' macro. The default configuration is to use the MCU R5F in Split mode, so both the R5F Core0 and Core1 are started before loading and booting the Linux kernel using the following firmware: MCU R5FSS0 Core0 (Split) : 0 /lib/firmware/am65x-mcu-r5f0_0-fw MCU R5FSS0 Core1 (Split) : 1 /lib/firmware/am65x-mcu-r5f0_1-fw The MCU R5FSS was initially running the R5 SPL in LockStep mode with ATCM disabled, and is actually shutdown to enable it to be reconfigured and booted by either A53 U-Boot or Linux kernel in remoteproc mode and using ATCM. The MCU R5FSS would need to be reconfigured for Lockstep mode through DT if a fault-tolerant/safety application were to be run on the cluster with the DEFAULT_RPROCS macro updated to remove the Core1 firmware. Signed-off-by: Suman Anna <s-anna@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-10-11env: ti: j721e-evm: Add support to boot rprocs including R5Fs and DSPsSuman Anna
Add support to boot some remoteprocs at U-boot prompt on the J721E EVM boards by using the 'boot_rprocs' and other env variables defined in the common environment file k3_rproc.h, and updating the 'DEFAULT_RPROCS' macro. The list of R5F cores to be started before loading and booting the Linux kernel are as follows, and in this order: Main R5FSS0 (Split) Core1 : 3 /lib/firmware/j7-main-r5f0_1-fw Main R5FSS1 (LockStep) : 4 /lib/firmware/j7-main-r5f1_0-fw The MCU R5FSS0 and Main R5FSS1 are currently in LockStep mode, so the equivalent Core1 rprocs (rproc #1 and #5) are not included. The Main R5FSS0 Core0 (rproc #2) is already started by R5 SPL, so is not included in the list either. The DSP cores are started in the following order before loading and booting the Linux kernel: C66_0: 6 /lib/firmware/j7-c66_0-fw C66_1: 7 /lib/firmware/j7-c66_1-fw C71_0: 8 /lib/firmware/j7-c71_0-fw The order of the rprocs to boot can be changed at runtime if desired by overwriting the 'rproc_fw_binaries' environment variable at U-boot prompt. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Signed-off-by: Suman Anna <s-anna@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-10-11env: ti: k3_rproc: Add common rproc environment variablesSuman Anna
Add a new file include/environment/ti/k3_rproc.h that defines common environment variables useful for booting various remote processors from U-Boot. This file is expected to be included in the board config files with the EXTRA_ENV_RPROC_SETTINGS added to CONFIG_EXTRA_ENV_SETTINGS and DEFAULT_RPROCS macro overwritten to include the actual list of processors to be booted. The 'boot_rprocs' variable just needs to be added to the board's bootcmd to automatically boot the processors, and runtime control can be achieved through the 'dorprocboot' variable. The variables are currently defined to use MMC as the boot media, and can be expanded in the future to include other boot media. The immediate usage is intended for K3 J721E SoCs. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Signed-off-by: Suman Anna <s-anna@ti.com>
2019-10-11remoteproc: elf_loader: Introduce rproc_elf_get_boot_addr() apiLokesh Vutla
Introduce rproc_elf_get_boot_addr() that returns the entry point of the elf file. This api auto detects the 64/32 bit elf file and returns the boot addr accordingly. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-10-11remoteproc: elf_loader: Introduce a common elf loader and checker functionsLokesh Vutla
Introduce a common remoteproc elf loader and checker functions that automatically detects the 64 bit elf file or 32 bit elf file and loads/checks the sections accordingly. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Fabien Dessenne <fabien.dessenne@st.com>
2019-10-11remoteproc: elf-loader: Add 64 bit elf loading supportLokesh Vutla
The current rproc-elf-loader supports loading of only 32 bit elf files. Introduce support for loading of 64 bit elf files in rproc-elf-loader. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Fabien Dessenne <fabien.dessenne@st.com>
2019-10-11remoteproc: elf_loader: Always check the validity of the image before loadingLokesh Vutla
rproc_elf32_load_image() rely on user to send a valid address for elf loading. Instead do a sanity check on the address passed by user. This will help all rproc elf users to not call sanity_check explicitly before calling elf_loading. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Fabien Dessenne <fabien.dessenne@st.com>
2019-10-11remoteproc: ops: Add elf section size as input parameter to device_to_virt apiLokesh Vutla
Introduce a new parameter "size" that accepts size of the region to remoteproc ops callback device_to_virt(). This can enforce more checks on the region that device_to_virt() is dealing with. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Tested-by: Fabien Dessenne <fabien.dessenne@st.com> Reviewed-by: Fabien Dessenne <fabien.dessenne@st.com>
2019-10-11dm: core: Add a function to count the children of a deviceLokesh Vutla
Add a function to count the available children of a device. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-10-11spl: ymodem: Make SPL Y-Modem loader framework accessibleAndreas Dannenberg
Expose SPL's Y-Modem core loader function via the common SPL header file so it can be re-used for purposes other than loading U-Boot itself. Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
2019-10-11trace: Remove the const from write functionsSimon Glass
The write functions do actually change the contents of memory so it is not correct to use 'const'. Remove it. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-10-11sandbox: pci: Remember the device being emulatedSimon Glass
Add a field to the PCI emulator per-device data which records which device is being emulated. This is useful when the emulator needs to check the device for something. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> [bmeng: rebase the patch against u-boot-x86/master to get it applied cleanly] Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
2019-10-09Merge tag 'xilinx-for-v2020.01' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze Xilinx/FPGA changes for v2020.01 FPGA: - Enable fpga loading on Versal - Minor fix Microblaze: - Fix LMB configurations to support initrds - Some other cleanups Zynq: - Minor config/dt changes - Add distro boot support for usb1 and mmc1 - Remove Xilinx private boot commands and use only distro boot ZynqMP: - Kconfig cleanups, defconfig updates - Update some dt files - Add firmware driver for talking to PMUFW - Extend distro boot support for jtag - Add new IDs - Add system controller configurations - Convert code to talk firmware via mailbox or SMCs Versal: - Add board_late_init() - Add run time DT memory setup - Add DFU support - Extend distro boot support for jtag and dfu - Add clock driver - Tune mini configurations Xilinx: - Improve documentation (boot scripts, dt binding) - Enable run time initrd_high calculation - Define default SYS_PROMPT - Add zynq/zynqmp virtual defconfig Drivers: - Add Xilinx mailbox driver for talking to firmware - Clean zynq_gem for Versal - Move ZYNQ_HISPD_BROKEN to Kconfig - Wire genphy_init() in phy.c - Add Xilinx gii2rgmii bridge - Cleanup zynq_sdhci - dwc3 fix - zynq_gpio fix - axi_emac fix Others: - apalis-tk1 - clean config file
2019-10-09Merge tag 'u-boot-imx-20191009' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-imx u-boot-imx-20191009 ------------------- Travis : https://travis-ci.org/sbabic/u-boot-imx/builds/595148532 - MX6UL / ULZ - Toradex board - Allow to set OCRAM for MX6Q/D - MX7ULP - MX8: (container image, imx8mq_mek), SCU API - fix several board booting from SD/EMMC (cubox-i for example) - pico boards [trini: display5 merged manually] Signed-off-by: Tom Rini <trini@konsulko.com>
2019-10-08Merge https://gitlab.denx.de/u-boot/custodians/u-boot-marvellTom Rini
- Move WATCHDOG_TIMEOUT_MSECS to Kconfig (Heiko)
2019-10-08Merge https://gitlab.denx.de/u-boot/custodians/u-boot-x86Tom Rini
- Rename existing FSP code to fsp1 - Add fsp2 directory in preparation to support FSP 2.0 - Various x86 platform codes update - Various bug fixes and updates in dm core, sandbox and spl
2019-10-08Merge tag 'u-boot-atmel-2020.01-a' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-atmel First set of u-boot-atmel features and fixes for 2020.01 cycle The feature set includes support for two new boards from Microchip AT91: The sama5d27_wlsom1_ek , an evaluation kit which includes the SAMA5D2 SOC packaged in a 256 MB LPDDR2 SIP, on a SOM including wireless, which is placed on evaluation kit with sd-card, ethernet, LCD, Camera sensor, QSPI, etc The sam9x60ek, an evaluation kit for the new SoC based on ARM926j , the SAM9X60 . The evaluation kit includes NAND flash, QSPI, Ethernet, Audio, Camera sensor connector, etc. The full support for sam9x60ek will come at a later time. There are still missing bits regarding the clock support and power management controller.
2019-10-08pico-imx7d: fix splash logo drawingJoris Offouga
Signed-off-by: Joris Offouga <offougajoris@gmail.com> Reviewed-by: Otavio Salvador <otavio@ossystems.com.br>
2019-10-08apalis_imx6: use distroboot by defaultIgor Opaniuk
Use distro_bootcmd as default bootcmd instead of legacy wrappers. Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2019-10-08colibri_imx6/imx7/imx8x: use distroboot by defaultIgor Opaniuk
Use distro_bootcmd as defauult bootcmd instead of legacy wrappers. Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2019-10-08imx: Add i.MX8MM EVK board support.Peng Fan
Add board and SoC dts Add ddr training code support SD/MMC/GPIO/PINCTRL/UART Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08imx: imx8mm: add clock bindings headerPeng Fan
Import clock bindings header file from Linux 5.3.0-rc2 Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08imx: mx6ul_14x14_evk: fix link issueAnatolij Gustschin
Since recent splash changes common code for splashscreen logo should be used instead of adding duplicated code under board directories. mx6ul_9x9_evk and mx6ul_14x14_evk configurations used old board specific logo code and do not link, fix them. Signed-off-by: Anatolij Gustschin <agust@denx.de> Acked-by: Peng Fan <peng.fan@nxp.com>
2019-10-08imx: add support for i.MX7/i.MX8MQ reset controllerPatrick Wildt
Add support for the reset controller that's used on the i.MX7D and i.MX8MQ. This will be needed to be able to assert the PCIe reset pins. Bindings taken from Linux, driver implementation mostly taken from Linux and adjusted to U-Boot infrastructure. Signed-off-by: Patrick Wildt <patrick@blueri.se> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-10-08imx: add support for i.MX8MQ power domain controllerPatrick Wildt
Add support for the power domain controller that's used on the i.MX8MQ. This will be needed to be able to power on the PCIe controller. Bindings taken from Linux, driver implementation taken from the i.MX8 power domain controller and adjusted for the i.MX8M SoC. Signed-off-by: Patrick Wildt <patrick@blueri.se>
2019-10-08imx: wandboard: convert FEC support to DM_ETHAnatolij Gustschin
Remove CONFIG_DM_ETH conversion warning to avoid board removal. Signed-off-by: Anatolij Gustschin <agust@denx.de>
2019-10-08DM: WDT: Convert WDT driver to use DM/DTS (including SYSRESET)Lukasz Majewski
This commit enables support for CONFIG_WDT in the U-Boot proper. Moreover, the SYSRESET_WATCHDOG driver is used to support 'reset' command. As SPL is not yet ready for DM conversion, the CONFIG_HW_WATCHDOG is enabled for it. This allows the legacy SPL code to work properly. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-08DM: SPI: Convert display5 to use SPI with DM/DTS (but no in SPL)Lukasz Majewski
The DM/DTS support for SPI is disabled on purpose for SPL, as it is not supported as of time of this conversion. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-08DM: eth: Switch display5 board to use DM_ETHLukasz Majewski
After this commit the display5 device would use FEC driver supporting driver model (DM_ETH). Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-08DM: I2C: Switch display5 board to use DM_I2CLukasz Majewski
After this commit the display5 device would use I2C driver supporting driver model (DM_I2C). The 'i2c' and 'eeprom' commands now use DM I2C drivers and initialize on-bus devices according to device tree description. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-08pico-imx6: Add Falcon modeFabio Estevam
Add Falcon mode support, which allows the SPL to load and jump to the Linux kernel directly, without the need of loading U-Boot proper. CONFIG_SPL_OS_BOOT=y needs to be passed in the defconfig in order to use Falcon mode. Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2019-10-08pico-imx6: Add splashscreen supportFabio Estevam
Add splashscreen support. Tested with the parallel FT5x06-WVGA panel. Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2019-10-08pico-imx6: Add Ethernet supportFabio Estevam
Add Ethernet support. Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2019-10-08pico-imx6: Fix bootmenu handlingOtavio Salvador
We should use a common script to allow booting the U-Boot console as fallback so we ended using a 'default_boot' and 'base_boot' environment scripts to accomplish that. Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2019-10-08pico-imx6: Add initial supportFabio Estevam
Add the initial support for the pico-imx6 variants. DDR initialization is based on the TechNexion's U-Boot code. Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2019-10-08mx53loco: Fix U-Boot corruption after saving the environmentFabio Estevam
U-Boot binary has grown in such a way that it goes beyond the reserved area for the environment variables. Running "saveenv" causes U-Boot to hang because of this overlap. Fix this problem by increasing the CONFIG_ENV_OFFSET size. Also, in order to prevent this same problem in the future, use CONFIG_BOARD_SIZE_LIMIT, which will detect the overlap in build-time. CONFIG_BOARD_SIZE_LIMIT does not accept math expressions, so declare CONFIG_ENV_OFFSET with its direct value instead. Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2019-10-08configs: pico-imx7d: Convert to DM_VIDEOJoris Offouga
This commit convert all pico-imx7d to DM_VIDEO Signed-off-by: Joris Offouga <offougajoris@gmail.com>
2019-10-08pico-imx7d: Add NYMPH baseboard supportOtavio Salvador
This add the boot menu option for the NYMPH baseboard as well as a specific config file for users which wish to use it as a pre-defined board. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2019-10-08pico-imx7d: Add DWARF baseboard supportOtavio Salvador
This add the boot menu option for the DWARF baseboard as well as a specific config file for users which wish to use it as a pre-defined board. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2019-10-08pico-imx6ul: Add LCD supportFabio Estevam
Add support for the VXT VL050-8048NT-C01 panel connected through the 24 bit parallel LCDIF interface. Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2019-10-08pico-imx6ul: Increase the CONFIG_ENV_OFFSET sizeFabio Estevam
U-Boot binary has grown in such a way that it goes beyond the reserved area for the environment variables. Running "saveenv" causes U-Boot to hang because of this overlap. Fix this problem by increasing the CONFIG_ENV_OFFSET size. Also, in order to prevent this same problem in the future, use CONFIG_BOARD_SIZE_LIMIT, which will detect the overlap in build-time. CONFIG_BOARD_SIZE_LIMIT does not accept math expressions, so declare CONFIG_ENV_OFFSET with its direct value instead. Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
generated by cgit (git 2.34.1) at 2024-12-29 17:33:40 +0000