summaryrefslogtreecommitdiff
path: root/include
AgeCommit message (Collapse)Author
2009-01-21mpc83xx: Add PCI-E support for MPC837XEMDS boardsAnton Vorontsov
MPC837XEMDS boards can support PCI-E via "PCI-E riser card". The card provides two PCI-E (x2) ports. Though, only one port can be used in x2 mode. Two ports can function simultaneously in x1 mode. PCI-E x1/x2 modes can be switched via "pex_x2" environment variable. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-01-21mpc83xx: Add PCI-E support for MPC8315ERDB boardsAnton Vorontsov
MPC8315ERDB boards features PCI-E x1 and Mini PCI-E x1 ports. Let's support them. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-01-21mpc83xx: Add support for MPC83xx PCI-E controllersAnton Vorontsov
This patch adds support for MPC83xx PCI-E controllers in Root Complex mode. The patch is based on Tony Li and Dave Liu work[1]. Though unlike the original patch, by default we don't register PCI-E buses for use in U-Boot, we only configure the controllers for future use in other OSes (Linux). This is done because we don't have enough of spare BATs to map all the PCI-E regions. To actually use PCI-E in U-Boot, users should explicitly define CONFIG_83XX_GENERIC_PCIE_REGISTER_HOSES symbol in the board file. And only then U-Boot will able to access PCI-E, but at the cost of disabled address translation. [1] http://lists.denx.de/pipermail/u-boot/2008-January/027630.html Signed-off-by: Tony Li <tony.li@freescale.com> Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Acked-by: Dave Liu <daveliu@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-01-2183xx: PCI agent mode fixes for multi-board systemsIra Snyder
When running a system with 2 or more MPC8349EMDS boards in PCI agent mode, the boards will lock up the PCI bus by scanning against each other. The boards lock against each other by trying to access the PCI bus before clearing their configuration lock bit. Both boards end up in a loop, sending and receiving "Target Not Ready" messages forever. When running in PCI agent mode, the scanning now takes place after the boards have cleared their configuration lock bit. Also, add a missing declaration to the mpc83xx.h header file, fixing a build warning. Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-01-21Merge branch 'master' into nextKim Phillips
2009-01-16Merge branch 'master' of git://git.denx.de/u-boot-shWolfgang Denk
2009-01-16sh: use write{8,16,32} in all lowlevel_initJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2009-01-14ppc4xx: Add loadpci command to esd's CPCI4052 and CPCI405AB boardsMatthias Fuchs
This patch adds esd's loadpci BSP command to CPCI4052 and CPCI405AB board. This requires CONFIG_CMD_BSP and CONFIG_PRAM. Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com> Signed-off-by: Stefan Roese <sr@denx.de>
2009-01-14Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxWolfgang Denk
2009-01-13Some changes of TLB entry setting for MPC8572DSHaiying Wang
- Move the TLB entry of PIXIS_BASE from TLB0 to TLB1[8], because in CAMP mode, all the TLB0 entries will be invalidated after cpu1 brings up kernel, thus cpu0 can not access PIXIS_BASE anymore (any access will cause DataTLBError exception) - Set CONFIG_SYS_DDR_TLB_START to 9 for MPC8572DS board. Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
2009-01-13mpc8610hpcd: Fix PCI mapping conceptsBecky Bruce
Rename _BASE to _BUS, as it's actually a PCI bus address, separate virtual and physical addresses into _VIRT and _PHYS, and use each appopriately. This makes the code easier to read and understand, and facilitates mapping changes going forward. Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
2009-01-13sbc8641d: Fix PCI mapping conceptsBecky Bruce
Rename _BASE to _BUS, as it's actually a PCI bus address, separate virtual and physical addresses into _VIRT and _PHYS, and use each appopriately. This makes the code easier to read and understand, and facilitates mapping changes going forward. Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
2009-01-06at91rm9200: move define from lowlevel_init to headerJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-01-06m501sk: move to the common memory setupJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-01-06at91rm9200: rename lowlevel init value to CONFIG_SYS_Jean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-12-30Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxWolfgang Denk
2008-12-30Merge branch 'master' of git://git.denx.de/u-boot-mipsWolfgang Denk
2008-12-29XPedite5200 board support cleanupPeter Tyser
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2008-12-20usb_kbd: fix usb_kbd_deregister when DEVICE_DEREGISTER not enableJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Signed-off-by: Remy Böhmer <linux@bohmer.net>
2008-12-19mpc8[56]xx: Put localbus clock in sysinfo and gdTrent Piepho
Currently MPC85xx and MPC86xx boards just calculate the localbus frequency and print it out, but don't save it. This changes where its calculated and stored to be more consistent with the CPU, CCB, TB, and DDR frequencies and the MPC83xx localbus clock. The localbus frequency is added to sysinfo and calculated when sysinfo is set up, in cpu/mpc8[56]xx/speed.c, the same as the other frequencies are. get_clocks() copies the frequency into the global data, as the other frequencies are, into a new field that is only enabled for MPC85xx and MPC86xx. checkcpu() in cpu/mpc8[56]xx/cpu.c will print out the local bus frequency from sysinfo, like the other frequencies, instead of calculating it on the spot. Signed-off-by: Trent Piepho <tpiepho@freescale.com> Acked-by: Kumar Gala <galak@kernel.crashing.org> Acked-by: Jon Loeliger <jdl@freescale.com>
2008-12-19sbc8548: use proper PHY addressPaul Gortmaker
The values given for the PHY address were wrong, so the code read no valid PHY ID, and fell through to the generic PHY support, which would work on 1000M but would not auto negotiate down to 100M or 10M. Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2008-12-19sbc8548: enable command line editing by default.Paul Gortmaker
Lets make things a bit more user friendly. It isn't 1985 anymore. Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2008-12-19sbc8548: don't enable the 3rd and 4th eTSECPaul Gortmaker
These interfaces don't have usable connectors on the board, so don't bother enumerating or configuring them. Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2008-12-19mpc8xxx: LCRR[CLKDIV] is sometimes five bitsTrent Piepho
On newer CPUs, 8536, 8572, and 8610, the CLKDIV field of LCRR is five bits instead of four. In order to avoid an ifdef, LCRR_CLKDIV is set to 0x1f on all systems. It should be safe as the fifth bit was defined as reserved and set to 0. Code that was using a hard coded 0x0f is changed to use LCRR_CLKDIV. Signed-off-by: Trent Piepho <tpiepho@freescale.com> Acked-by: Kumar Gala <galak@kernel.crashing.org> Acked-by: Jon Loeliger <jdl@freescale.com>
2008-12-19ppc: Use addrmap in virt_to_phys and map_physmem.Kumar Gala
If we have addr map support enabled use the mapping functions to implement virt_to_phys() and map_physmem(). Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-12-1985xx: Add support to populate addr map based on TLB settingsKumar Gala
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-12-19XPedite5370 board supportPeter Tyser
Initial support for Extreme Engineering Solutions XPedite5370 - a MPC8572-based 3U VPX single board computer with a PMC/XMC site. Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2008-12-19Add support for PCA953x I2C gpio devicesPeter Tyser
Initial support for NXP's 4 and 8 bit I2C gpio expanders (eg pca9537, pca9557, etc). The CONFIG_PCA953X define enables support for the devices while the CONFIG_CMD_PCA953X define enables the pca953x command. The CONFIG_CMD_PCA953X_INFO define enables an 'info' sub-command which provides summary information for the given pca953x device. Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2008-12-17avr32: Remove second definition of virt_to_phys()Haavard Skinnemoen
The second definition introduced by 65e43a1063 conflicts with the existing one. Also, convert the existing definition to use phys_addr_t. The volatile qualifier is still needed due to brain damage elsewhere. Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-12-17MIPS: qemu_mips: move env storage just after u-bootJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
2008-12-16include/configs/at91cap9adk.h: fix typo.Wolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-12-16powerpc: fix io.h build warning with CONFIG_PHYS_64BITBecky Bruce
Casting a pointer to a phys_addr_t when it's an unsigned long long on a 32-bit system without first casting to a non-pointer type generates a compiler warning. Fix this. Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
2008-12-16Coding style cleanup, update CHANGELOG.Wolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-12-15i2c: merge all i2c_reg_read() and i2c_reg_write() into inline functionsTimur Tabi
All implementations of the functions i2c_reg_read() and i2c_reg_write() are identical. We can save space and simplify the code by converting these functions into inlines and putting them in i2c.h. Signed-off-by: Timur Tabi <timur@freescale.com> Acked-By: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-12-15Introduce addr_map libraryKumar Gala
Add a library that helps in translating between virtual and physical addresses. This library can be useful as a simple means to implement map_physmem() and virt_to_phys() for platforms that need functionality beyond the simple 1:1 mapping. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-12-15Introduce virt_to_phys()Kumar Gala
virt_to_phys() returns the physical address given a virtual. In most cases this will be just the input value as the vast majority of systems run in a 1:1 mode. However in systems that are not running this way it should report the physical address or ~0 if no mapping exists for the given virtual address. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-12-14Remove unused CONFIG_ADDR_STREAMING definesPeter Tyser
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2008-12-14Fix new found CFG_Jean-Christophe PLAGNIOL-VILLARD
Also fix some minor typos. Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-12-13Fix FIT and FDT support to have CONFIG_OF_LIBFDT and CONFIG_FIT independentJean-Christophe PLAGNIOL-VILLARD
FDT support is used for both FIT style images and for architectures that can pass a fdt blob to an OS (ppc, m68k, sparc). For other architectures and boards which do not pass a fdt blob to an OS but want to use the new uImage format, we just need FIT support. Now we can have the 4 following configurations : 1) FIT only CONFIG_FIT 2) fdt blob only CONFIG_OF_LIBFDT 3) both CONFIG_OF_LIBFDT & CONFIG_FIT 4) none none Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-12-13Merge branch 'master' of git://git.denx.de/u-boot-ppc4xxWolfgang Denk
2008-12-13Merge branch 'master' of git://git.denx.de/u-boot-shWolfgang Denk
2008-12-13Merge branch 'master' of git://git.denx.de/u-boot-microblazeWolfgang Denk
2008-12-13Merge branch 'master' of git://git.denx.de/u-boot-ubiWolfgang Denk
2008-12-10sh: Changed value of CACHE_OC_NUM_ENTRIES and CACHE_OC_WAY_SHIFTNobuhiro Iwamatsu
SH4 is different a value of CACHE_OC_NUM_ENTRIES and CACHE_OC_WAY_SHIFT every CPU. This patch corrects these values. Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2008-12-10sh: Update ms7722se board configNobuhiro Iwamatsu
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2008-12-10ppc4xx: Update TEXT_BASE for CPCI405 boardsMatthias Fuchs
This patch fixes building U-Boot for CPCI405 boards. Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com> Signed-off-by: Stefan Roese <sr@denx.de>
2008-12-10ppc4xx: Remove some features from ALPR to fit into 256k againStefan Roese
Signed-off-by: Stefan Roese <sr@denx.de>
2008-12-10microblaze: Remove XUPV2P boardMichal Simek
--- Microblaze platforms use generic settings and to have many platforms is confusing that's why I decided to remove this platform from U-BOOT. ml401 tree is sufficient for covering all Microblaze platforms. This change will go through microblaze custodian tree.
2008-12-10microblaze: Remove CONFIG_LIBFDT due to error in common filesMichal Simek
2008-12-10microblaze: Fix ml401 uart16550 settingMichal Simek
Signed-off-by: Michal Simek <monstr@monstr.eu>
generated by cgit (git 2.34.1) at 2024-12-27 11:15:09 +0000