| Age | Commit message (Collapse) | Author |
|---|
|
T4240 PCIe IP is version 3.0 and has some update comparing previous
QorIQ products.
1. Move Freescale specific register define
to
arch/powerpc/include/asm/fsl_pci.h
and update the register offset define for T4240.
2. add the status/control register define
use status/control register to judge the link status
3. The original code uses 'Programming Interface' field to judge if PCIE is
EP or RC mode, however, T4240 does not support this functionality.
According to PCIE specification, 'Header Type' offset 0x0e is used to
indicate header type, so for PCIE controller, the patch changes code to
use 'Header Type' field to identify if the PCIE is RC or EP mode.
This patch fixes the PCIe card link up issue on T4240QDS.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
|
|
1. Add CONFIG_SYS_DPAA_RMAN macro to t4240 and b4860.
2. Decrease RMan liodn offset number.
SET_RMAN_LIODN() is used to set liodn offset of RMan blocks 0-3.
For t4240 and b4860, RMan liodn base is assigned to 922, the original
offset number is too large that the liodn (base+offset 922+678 = 1600)
is greater than 0x500 the maximum liodn number.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
|
|
1) Add support in B4860 board files for using IDT driver where
IDT8T49N222A is a low phase noise Frequency Translator / Synthesizer
that generate different refclks for SerDes modules, used this driver
for reconfiguring SerDes1 Refclks(based on SerDes1 protocols)
for CPRI to work. CPRI works on 122.88MHz and default refclks coming
on board are not suitable for it
2) Move SerDes1 refclk1 source selection from eth_b4860qds.c file
to b4860qds board file, as SerDes1 Refclk1 would come from
PHY MUX in case of certain protocols, that have been checked here.
This change would make on board SGMIIs to work
3) Add I2C addresses for IDT8T49N222A devices in board/include file
4) Add define for PCA-I2C bus multiplexer, on which IDT devices exist
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
|
|
BSC9132QDS is a Freescale Reference Design Board for BSC9132 SoC which is a
integrated device that contains two powerpc e500v2 cores and two DSP
starcores.
To support DSP starcore
-Creating LAW and TLB for DSP-CCSR space.
-Creating LAW for DSP-core subsystem M2 and M3 memory
-Creating LAW for 1GB DDR which is connected exclusively to DSP-cores
Signed-off-by: Manish Jaggi <manish.jaggi@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
|
|
Add new board p1020RDB-PD. P1020RDB-PD board was update from P1020RDB.
DDR changed from DDR2 1G to DDR3 2G.
NAND: 128 MiB
Flash: 64 MiB
Also change P1020RDB to P1020RDB-PC to distinguish from P1020RDB board.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
CC: Scott Wood <scottwood@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
|
|
JEDEC spec requires the clocks to be stable before deasserting reset
signal for RDIMMs. Clocks start when any chip select is enabled and
clock control register is set. This patch also adds the interface to
toggle memory reset signal if needed by the boards.
Signed-off-by: York Sun <yorksun@freescale.com>
|
|
Add emulator support for T4240. Emulator has limited peripherals and
interfaces. Difference between emulator and T4240QDS includes:
ECC for DDR is disabled due the procedure to load images
No board FPGA (QIXIS)
NOR flash has 32-bit port for higher loading speed
IFC and I2C timing don't really matter, so set them fast
No ethernet
Signed-off-by: York Sun <yorksun@freescale.com>
|
|
CONFIG_PHYS_64BIT is always defined for t4qds. Removed unused #ifdef.
Signed-off-by: York Sun <yorksun@freescale.com>
|
|
Move CONFIG_FSL_CORENET define to config_mpc85xx.h. It is not board
specific feature and belongs to SoC header.
Signed-off-by: York Sun <yorksun@freescale.com>
|
|
TWR-P1025 Specification:
-----------------------
Memory subsystem:
512MB DDR3 (on board DDR)
64Mbyte 16bit NOR flash
One microSD Card slot
Ethernet:
eTSEC1: Connected to Atheros AR8035 GETH PHY
eTSEC3: Connected to Atheros AR8035 GETH PHY
UART:
Two UARTs are routed to the FDTI dual USB to RS232 convertor
USB: Two USB2.0 Type A ports
I2C:
AT24C01B 1K Board EEPROM (8 bit address)
QUICC Engine:
Connected to DP83849i PHY supply two 10/100M ethernet ports
QE UART for RS485 or RS232
PCIE:
One mini-PCIE slot
Signed-off-by: Michael Johnston <michael.johnston@freescale.com>
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
[yorksun: Fixup include/configs/p1_twr.h]
Signed-off-by: York Sun <yorksun@freescale.com>
|
|
|
|
In case only the CONFIG_SYS_I2C_SPEED is set in configuration file,
the CONFIG_SYS_I2C_SOFT_SPEED is defined as CONFIG_SYS_I2C_SPEED.
The CONFIG_SYS_I2C_SOFT_SPEED is then used throughout the driver.
Unfortunatelly, due to a typo in the driver, instead of defining
CONFIG_SYS_I2C_SOFT_SPEED, an CONFIG_SYS_SOFT_I2C_SPEED was defined
and therefore the driver failed to compile. The same applies for
CONFIG_SYS_I2C_SOFT_SLAVE , where the swap happens as well.
This patch fixes the issue.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
|
|
Now that nothing uses CONFIG_ARCH_DEVICE_TREE, stop defining it.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Aside from microblaze, all other SoCs/boards/vendors store their DT files
in board/$vendor/dts/$soc-$board.dts. Move microblaze-generic.dts to this
location for consistency.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Michal Simek <monstr@monstr.eu>
|
|
|
|
This commit adds some prototypes into include/mtd/cfi_flash.h.
These functions are defined with a weak attribute in
drivers/mtd/cfi_flash.c.
This means they can be overrided by board-specific ones
if necessary.
When defining such functions under board/ directory or
somewhere, cfi_flash.h should be included.
This makes sure that board-specfic cfi functions
are defined in a correct prototype.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
switch
This patch extends dfu code to support transmission with -R switch
specified at dfu-util.
When -R is specified, the extra USB_REQ_DFU_DETACH request is sent after
successful data transmission. Then dfu resources are released and reset
command is issued.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
|
|
The requests sent to the controller are not properly cache aligned
most of the time, thus implement a simple bounce buffer to avoid
problem with cache.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
|
|
Allocate the qTD items all at once instead of allocating them
separately. Moreover, make sure each qTD is properly aligned
to 32-bytes boundary and that cache can be safely flushed over
each qTD touple.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
|
|
Both the endpoint queue head and the endpoint item list is a controller
specific thing. Move them both into controller private data.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
|
|
The usb_lowlevel_init() call already fills and passes back struct
ehci_ctrl , which readily contains correctly determined address of
the port register block address computed from values from controller
configuration registers. Leverage this and make use of this value
as this makes the code mode universal, but also gets us rid of the
CONFIG_USB_REG_BASE configuration option.
Moreover, this patch cleans up the usb_gadget_register_driver() call
a little by correcting the error handling. Note the usb_lowlevel_init()
and mvudc_probe() are now called in reversed order, but this has no
impact on the code.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
|
|
Move the constant values that are programmed into mv_ep.ep into
separate static const structure so they can be memcpy()'d when
the initialization happens.
Moveover, we only every init NUM_ENDPOINTS, not 2 * NUM_ENDPOINTS,
so fix this bug as well.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
|
|
The endpoints are operated on a per-controller basis, move the
endpoint array into controller's private data. Also shuffle the
struct mv_ep structure definition just above the definition of
the struct mv_drv so they're well grouped together.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
|
|
Do a coding-style cleanup of this file and throw away useless
defined values. These values were likely a result of a copy-paste
job.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
|
|
CONFIG_SYS_FLASH_PROTECTION was active on most gdsys boards by default,
while hardware flash protection was not implemented.
Hardware support was added recently and we get into trouble because backward
compatibility is broken (u-boot can't unprotect the protected flash after a
downgrade). So we decided to disable hardware flash protection for all our boards.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
A set of accessor functions was added to be able to access not only
memory mapped FPGA in a generic way.
Thanks to Wolfgang Denk for getting this sorted properly.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
|
|
Signed-off-by: Tom Rini <trini@ti.com>
|
|
Conflict over SPDX changes means that one change was effectively dropped
as it was fixing typos in a removed hunk of text.
Conflicts:
arch/mips/cpu/mips64/start.S
Signed-off-by: Tom Rini <trini@ti.com>
|
|
Qemu emulates a PCNET PCI card for the Malta CoreLV board.
Enable the pcnet driver and add board specific ethernet
initialization function to bring it up. Also enable the
CONFIG_CMD_NET and CONFIG_CMD_PING options.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
|
|
Qemu emulates the Galileo GT64120 System Controller
which provides a CPU bus to PCI bus bridge.
The patch adds driver for this bridge and enables
PCI support for the emulated Malta board.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
|
|
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
|
|
Add minimal support for the MIPS Malta CoreLV board
emulated by Qemu. The only supported peripherial is
the UART.
This is enough to boot U-Boot to the command prompt
both in little and big endian mode.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
|
|
The Linux specific register access macros, the
extern function declarations and the UL suffixes
has been removed.
The header file will be used for the qemu-malta
board.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
|
|
The sandburst-specific i2c drivers have been deleted, conflict was just
over the SPDX conversion.
Conflicts:
board/sandburst/common/ppc440gx_i2c.c
board/sandburst/common/ppc440gx_i2c.h
Signed-off-by: Tom Rini <trini@ti.com>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
|
|
Add a header file, setup.h, which copy from Linux source code,
this file contain structures are used to pass initialisation parameters
to Linux. Enable this function on adp-ag101/adp-ag101p target
Signed-off-by: Kuan-Yu Kuo <ken.kuoky@gmail.com>
Cc: Macpaul Lin <macpaul@gmail.com>
|
|
Signed-off-by: Kuan-Yu Kuo <ken.kuoky@gmail.com>
Cc: Macpaul Lin <macpaul@gmail.com>
|
|
The original adp-ag101/adp-ag101p initialize only one bank(64MB)
by default at boot time, but it is not enough for some application,
so increasing to two banks(128M).
Signed-off-by: Kuan-Yu Kuo <ken.kuoky@gmail.com>
Cc: Macpaul Lin <macpaul@gmail.com>
|
|
Even though the header files is used only by the
pci_ftpci100 driver, it contains declaration for
a function which is used by external code.
Move the header file to a common location which
lets external code use it.
Compile tested only.
Cc: Macpaul Lin <macpaul@andestech.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
|
|
Add a const keyword to the sect_buf argument of
ide_write_data to fix the following warning:
cmd_ide.c: In function '__ide_output_data':
cmd_ide.c:548: warning: passing argument 2 of 'ide_write_data' discards qualifiers from pointer target type
/devel/u-boot.git/include/ide.h:76: note: expected 'ulong *' but argument is of type 'const ulong *'
Also modify the driver-model documentation to
match with the new prototype.
Compile tested only.
Cc: Macpaul Lin <macpaul@andestech.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
|
|
Adds a new COMPAT string exynos5-hsi2c for high speed i2c controller
available on exynos5 SoCs from Samsung.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
|
|
This patch adds I2C support for Vybrid VF610 platform and adds
I2C0 support to VF610TWR board.
Signed-off-by: Alison Wang <b18965@freescale.com>
|
|
Due to the new I2C framework we need to adapt the u-boot update
function. Due to the new framework all i2c leafs behind a mux are
present in the system and not only those who are defined and used. So it
is bus number 5 after the rework.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Heiko Schocher <hs@denx.de>
cc: Prafulla Wadaskar <prafulla@marvell.com>
|
|
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Heiko Schocher <hs@denx.de>
Cc: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
|
|
This enables CONFIG_SYS_I2C on Tegra, updating existing boards and the Tegra
i2c driver to support this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
as the keymile boards use now the new i2c multibus/multiadapter
framework, remove the EEprom_ivm Environmentvar, as not longer
needed.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Holger Brunck <holger.brunck@keymile.com>
Tested-By: Holger Brunck <holger.brunck@keymile.com>
|
