summaryrefslogtreecommitdiff
path: root/include
AgeCommit message (Collapse)Author
2020-07-29drivers: tee: broadcom: add optee based bnxt fw load driverVikas Gupta
Add optee based bnxt fw load driver. bnxt is Broadcom NetXtreme controller Ethernet card. This driver is used to load bnxt firmware binary using OpTEE. Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com> Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2020-07-29dt-bindings: pinctrl: add ns3 pads definitionRayagonda Kokatanur
Add NS3 pads definitions. Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2020-07-29include/configs: ns3: add support for flashing imagesBharat Gooty
Add support for flashing images into QSPI and eMMC. Signed-off-by: Bharat Gooty <bharat.gooty@broadcom.com> Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2020-07-29include/configs: ns3: add env variables for Linux bootBharat Gooty
Add env variables and commands for booting Linux. Signed-off-by: Bharat Gooty <bharat.gooty@broadcom.com> Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2020-07-29dt-bindings: memory: ns3: add ddr memory definitionRayagonda Kokatanur
Add ddr memory definitions. Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2020-07-29dt-bindings: memory: ns3: add memory definitionsRayagonda Kokatanur
Add NS3 memory definitions. Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2020-07-29board: ns3: add support for Broadcom Northstar 3Rayagonda Kokatanur
Add support for Broadcom Northstar 3 SoC. NS3 is a octo-core 64-bit ARMv8 Cortex-A72 processors targeting a broad range of networking applications. Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2020-07-29board: mediatek: Use CONFIG_DEFAULT_FDT_FILE for default environmentDavid Woodhouse
Rather than hard-coding it to the Banana Pi R2. Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-29arm: add (default) config for nanopi2 boardStefan Bosch
Changes in relation to FriendlyARM's U-Boot nanopi2-v2016.01: - Configuration changed, mainly several "CONFIG_..." moved from s5p4418_nanopi2.h to s5p4418_nanopi2_defconfig and USB related configs removed because USB is not supported yet. - s5p4418_nanopi2.h: "CONFIG_" removed from several s5p4418/nanopi2 specific defines because the appropriate values do not need to be configurable. - pinctrl is supported now, therefore "CONFIG_PINCTRL=y" added to s5p4418_nanopi2_defconfig. Signed-off-by: Stefan Bosch <stefan_b@posteo.net>
2020-07-29arm: qemu: override flash accessors to use virtualizable instructionsArd Biesheuvel
Some instructions in the ARM ISA have multiple output registers, such as ldrd/ldp (load pair), where two registers are loaded from memory, but also ldr with indexing, where the memory base register is incremented as well when the value is loaded to the destination register. MMIO emulation under KVM is based on using the architecturally defined syndrome information that is provided when an exception is taken to the hypervisor. This syndrome information describes whether the instruction that triggered the exception is a load or a store, what the faulting address was, and which register was the destination register. This syndrome information can only describe one destination register, and when the trapping instruction is one with multiple outputs, KVM throws an error like kvm [615929]: Data abort outside memslots with no valid syndrome info on the host and kills the QEMU process with the following error: U-Boot 2020.07-rc3-00208-g88bd5b179360-dirty (Jun 06 2020 - 11:59:22 +0200) DRAM: 1 GiB Flash: error: kvm run failed Function not implemented R00=00000001 R01=00000040 R02=7ee0ce20 R03=00000000 R04=7ffd9eec R05=00000004 R06=7ffda3f8 R07=00000055 R08=7ffd9eec R09=7ef0ded0 R10=7ee0ce20 R11=00000000 R12=00000004 R13=7ee0cdf8 R14=00000000 R15=7ff72d08 PSR=200001d3 --C- A svc32 QEMU: Terminated This means that, in order to run U-Boot in QEMU under KVM, we need to avoid such instructions when accessing emulated devices. For the flash in particular, which is a hybrid between a ROM (backed by a read-only KVM memslot) when in array mode, and an emulated MMIO device (when in write mode), we need to take care to only use instructions that KVM can deal with when they trap. So override the flash read accessors that are used when running on QEMU under KVM. Note that the the 64-bit wide read and write accessors have been omitted: they are never used when running under QEMU given that it does not emulate CFI flash that supports it. Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Reviewed-by: Andre Przywara <andre.przywara@arm.com>
2020-07-28configs: migrate CONFIG_SPL_LOAD_FIT_ADDRESS to defconfigsPeng Fan
Done with: ./tools/moveconfig.py -S SPL_LOAD_FIT_ADDRESS ./tools/moveconfig.py -S SPL_LOAD_FIT_ADDRESS -H Signed-off-by: Peng Fan <peng.fan@nxp.com> [trini: A few more migrations] Signed-off-by: Tom Rini <trini@konsulko.com>
2020-07-28Convert CONFIG_SYS_MMCSD_FS_BOOT_PARTITION to KconfigAdam Ford
This converts the following to Kconfig: CONFIG_SYS_MMCSD_FS_BOOT_PARTITION Signed-off-by: Adam Ford <aford173@gmail.com>
2020-07-28configs: Remove dead CONFIG optionsAdam Ford
BOOTP_DEFAULT is defined in several boards, but this config option is never checked or used. This patch removes this config option from config files and the whitelist.txt Signed-off-by: Adam Ford <aford173@gmail.com>
2020-07-28Convert CONFIG_BOOTP_SEND_HOSTNAME to KconfigAdam Ford
This converts the following to Kconfig: CONFIG_BOOTP_SEND_HOSTNAME Signed-off-by: Adam Ford <aford173@gmail.com>
2020-07-28Convert CONFIG_DRIVER_TI_EMAC_USE_RMII to KconfigAdam Ford
This converts the following to Kconfig: CONFIG_DRIVER_TI_EMAC_USE_RMII Signed-off-by: Adam Ford <aford173@gmail.com>
2020-07-28Convert CONFIG_SPL_NAND_BASE et al to KconfigAdam Ford
This converts the following to Kconfig: CONFIG_SPL_NAND_BASE CONFIG_SPL_NAND_IDENT Signed-off-by: Adam Ford <aford173@gmail.com>
2020-07-28Convert CONFIG_SPL_NAND_DRIVERS et al to KconfigAdam Ford
This converts the following to Kconfig: CONFIG_SPL_NAND_DRIVERS CONFIG_SPL_NAND_ECC CONFIG_SPL_NAND_SIMPLE Signed-off-by: Adam Ford <aford173@gmail.com>
2020-07-28Convert CONFIG_ENV_OVERWRITE to KconfigAdam Ford
This converts the following to Kconfig: CONFIG_ENV_OVERWRITE Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Rerun migration, remove some comments] Signed-off-by: Tom Rini <trini@konsulko.com>
2020-07-27Merge https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriqTom Rini
- Bug fixes and updates on ls2088a,ls1028a, ls1046a, ls1043a, ls1012a - lx2-watchdog support - layerscape: pci-endpoint support, spin table relocation fixes and cleanups - fsl-crypto: RNG support and bug fixes
2020-07-27Merge tag 'dm-pull-20jul20-take2a' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-dm binman support for FIT new UCLASS_SOC patman switch 'test' command minor fdt fixes patman usability improvements
2020-07-27Merge https://gitlab.denx.de/u-boot/custodians/u-boot-shTom Rini
- R8A774A1 / Beacon EmbeddedWorks RZG2M Dev Kit support
2020-07-27Merge branch 'net' of https://gitlab.denx.de/u-boot/custodians/u-boot-shTom Rini
- Convert dc2114x driver to DM.
2020-07-27pci_ep: Add the init functionXiaowei Bao
Some EP deivces need to initialize before RC scan it, e.g. NXP layerscape platform, so add the init function in pci_ep uclass. Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com> Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-07-27crypto/fsl: instantiate the RNG with prediciton resistanceMichael Walle
If it is already instantiated tear it down first and then reinstanciate it again with prediction resistance. Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-07-27crypto/fsl: don't regenerate secure keysMichael Walle
The secure keys (TDKEK, JDKEK, TDSK) can only be generated once after a POR. Otherwise the RNG4 will throw an error. Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Horia Geantă <horia.geanta@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-07-27crypto/fsl: support newer SEC modulesMichael Walle
Since Era 10, the version registers changed. Add the version registers and use them on newer modules. Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Horia Geantă <horia.geanta@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-07-27crypto/fsl: export caam_get_era()Michael Walle
We need the era in other modules, too. For example, to get the RNG version. Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Horia Geantă <horia.geanta@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-07-27configs: ls1012a: Increase CONFIG_SYS_MALLOC_LEN valueKuldeep Singh
Previous attempt to increase CONFIG_SYS_MALLOC_LEN was done in commit c084a8edf4e2 ("configs: ls1012a: Increase CONFIG_SYS_MALLOC_LEN size") which increased malloc memory to ~1M. PFE firmware alone requires 3M of dynamic memory allocation and therefore, increase the config value to a larger value i.e 5M. This size should be enough as of now to accommodate further memory requirements. Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-07-27Move eSDHC adapter card identification to board filesYangbo Lu
The eSDHC adapter card identification and multiplexing configuration through FPGA had been implemented in both common mmc driver and fsl_esdhc driver. However it is proper to move these code to board files and do it during board initialization. The FPGA registers are also board specific. This patch is to move eSDHC adapter card identification and multiplexing configuration from mmc driver to specific board files. And the option CONFIG_FSL_ESDHC_ADAPTER_IDENT is no longer needed. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> [Rebased, Removed T1040QDS change as board does not exist] Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-07-27armv8: ls1028ardb: add xspi parameter to qixis commandYuantian Tang
Add xspi boot source to qixis command to let the soc boot from flex-nor flash chip. Signed-off-by: Yuantian Tang <andy.tang@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-07-27include/configs: ls1012a: Remove fdt_high env variableUdit Agarwal
Remove "fdt_high" environment variable to use the bootm_size to safely contain a kernel, device tree and initrd for relocation. Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-07-27I2C: ls1043a, ls1046a: enable SYS_I2C_MXCBiwen Li
This enables SYS_I2C_MXC to fix a bug that failed to boot from sd card with image u-boot-with-spl-pbl.bin Signed-off-by: Biwen Li <biwen.li@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-07-27armv8: layerscape: properly use CPU_RELEASE_ADDRMichael Walle
The generic armv8 code already has support to bring up the secondary cores. Thus, don't hardcode the jump in the layerscape lowlevel_init to the spin table code; instead just return early and let the common armv8 code handle the jump. This way we can actually use the CPU_RELEASE_ADDR feature. Signed-off-by: Michael Walle <michael@walle.cc> [Rebased, Removed kontron_sl28.h change as file does not exist] Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-07-27net: pfe_eth: Use spi_flash_read API to access flash memoryKuldeep Singh
Current PFE firmware access spi-nor memory directly. New spi-mem framework does not support direct memory access. So, let's use spi_flash_read API to access memory instead of directly using it. Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com> Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-07-27configs: ls1088ardb: Add support for usb boot targetEra Tiwari
LS1088A-RDB has MMC, SCSI, DHCP as boot targets, but the USB support was missing. Add support for USB as Boot_targets_devices. Signed-off-by: Era Tiwari <era.tiwari@nxp.com> Signed-off-by: Pramod Kumar <pramod.kumar_1@nxp.com> [Rebased] Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-07-27armv8: ls1028a: move FSL_LAYERSCAPE to kconfigMichael Walle
CONFIG_FSL_LAYERSCAPE is available in kconfig. There is no need to define it per board; the ls1028a_common.h is really board dependent and only fits to the NXP eval boards. Instead select CONFIG_FSL_LAYERSCAPE when ARCH_LS1028A is selected. Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-07-27fsl_dspi: Introduce DT bindings for CS-SCK and SCK-CS delaysVladimir Oltean
Communication with some SPI slaves just won't cut it if these delays (before the beginning, and after the end of a transfer) are not added to the Chip Select signal. These are a straight copy from Linux: Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt drivers/spi/spi-fsl-dspi.c Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> [Rebased] Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-07-26cmd: env: check real location for env info commandPatrick Delaunay
Check the current ENV location, dynamically provided by the weak function env_get_location to be sure that the environment can be persistent. The compilation flag ENV_IS_IN_DEVICE is not enough when the board dynamically select the available storage location (according boot device for example). This patch solves issue for stm32mp1 platform, when the boot device is USB. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
2020-07-25dm: soc: Introduce UCLASS_SOC for SOC ID and attribute matchingDave Gerlach
Introduce UCLASS_SOC to be used for SOC identification and attribute matching based on the SoC ID info. This allows drivers to be provided for SoCs to retrieve SoC identifying information and also for matching device attributes for selecting SoC specific data. This is useful for other device drivers that may need different parameters or quirks enabled depending on the specific device variant in use. Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
2020-07-25Revert "lib: fdt: Split fdtdec_setup_mem_size_base()"Michal Simek
This reverts commit 3ebe09d09a407f93022d945a205c5318239eb3f6. There is no user of this split function that's why remove it. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2020-07-25Revert "lib: fdt: Split fdtdec_setup_memory_banksize()"Michal Simek
This reverts commit 118f4d4559a4386fa87a1e2509e84a1986b24a34. There is no user of this split function that's why remove it. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2020-07-25cpu: Convert the methods to use a const udevice *Simon Glass
These functions should not modify the device. Convert them to const so that callers don't need to cast if they have a const udevice *. Signed-off-by: Simon Glass <sjg@chromium.org>
2020-07-25ARM: rmobile: Add Beacon EmbeddedWorks RZG2M Dev KitAdam Ford
The Beacon EmbeddedWorks kit is based on the R8A774A1 SoC also known as the RZ/G2M. The kit consists of a SOM + Baseboard and supports microSD, eMMC, Ethernet, a couple celular radios, two CAN interfaces, Bluetooth and WiFi. Signed-off-by: Adam Ford <aford173@gmail.com>
2020-07-25net: dc2114x: Add Kconfig entriesMarek Vasut
Add Kconfig entries for the dc2114x driver and convert various boards. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Ramon Fried <rfried.dev@gmail.com>
2020-07-25ARM: dts: r8a774a1: Import DTS from Linux 5.8-rc1Adam Ford
This patch imports the device tree and required bindings to permit the device tree to build for the R8Z774A1 (RZ/G2M). Signed-off-by: Adam Ford <aford173@gmail.com>
2020-07-24Merge https://gitlab.denx.de/u-boot/custodians/u-boot-riscvTom Rini
- Fix SiFive HiFive Unleashed board booting failure problem. - Enable SiFive fu540 PWM driver. - Support SiFive fu540: SPI boot. - Update OpenSBI used for RISC-V CI testing. - Revert "riscv: Allow use of reset drivers". - Revert "Revert "riscv: sifive: fu540: Add gpio-restart support"". - sysreset: syscon: - Don't assume default value for offset and mask property. - Support value property. - qemu: Add syscon reboot and poweroff support. - Fix SIFIVE debug serial dependency. - Fix linking error when building u-boot-spl with no SMP support. - AE350 use fdtdec_get_addr_size_auto_noparent to parse smc reg. - Make memory node available to SPL in hifive-unleashed-a00-u-boot.dtsi - SiFive fu540 avoid using hardcoded ram base and size.
2020-07-24Revert "Merge tag 'dm-pull-20jul20' of git://git.denx.de/u-boot-dm"Tom Rini
This reverts commit 5d3a21df6694ebd66d5c34c9d62a26edc7456fc7, reversing changes made to 56d37f1c564107e27d873181d838571b7d7860e7. Unfortunately this is causing CI failures: https://travis-ci.org/github/trini/u-boot/jobs/711313649 Signed-off-by: Tom Rini <trini@konsulko.com>
2020-07-24sifive: fu540: Enable SF distro bootcmdJagan Teki
Enable SPI flash(SF) distro boot command in Sifive FU540. This distro boot will read the boot script at specific location at the flash and start sourcing the same. Included the SF device at the last of the target devices list since all the rest of the devices on the list have more possibility to boot the distribution due to the size of the SPI flash is concern. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Bin Meng <bin.meng@windriver.com>
2020-07-24sifive: fu540: Add boot flash script offset, sizeJagan Teki
HiFive-Unleashed-A00 has SPI flash with 32MiB size. So, let's use the script offset at the end of 4K. This way it cannot overlap any offsets being used by software components in flash layout. So, SF distrocmd will pick the script at desired script address and run. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Bin Meng <bin.meng@windriver.com>
2020-07-23Merge tag 'dm-pull-20jul20' of git://git.denx.de/u-boot-dmTom Rini
binman support for FIT new UCLASS_SOC patman switch 'test' command minor fdt fixes patman usability improvements
generated by cgit (git 2.34.1) at 2024-12-23 23:19:36 +0000