summaryrefslogtreecommitdiff
path: root/include
AgeCommit message (Collapse)Author
2012-01-16arm, davinci: Use a common configuration file for da850evm and da850_am18xxevmChristian Riesch
In commit 06194b6b65f701a9d6ef2d9b4123c4afe57d8783 a separate header file was introduced for the AM1808 EVM, include/configs/da850_am18xxevm.h. Before this commit, the da850evm.h configuration file was used for both the AM1808 and the OMAP-L138 EVMs. The only substantial difference between the da850evm and the da850_am18xxevm configuration is a single bit in the hardware revision that is passed to the Linux kernel. This patch removes include/configs/da850_am18xxevm.h. Instead the include/configs/da850evm.h configuration is used for AM18xx EVMs and CONFIG_DA850_AM18X_EVM is defined in boards.cfg. Signed-off-by: Christian Riesch <christian.riesch@omicron.at> Cc: Tom Rini <trini@ti.com>
2012-01-16i.mx: i.mx6q: add the initial support for i.mx6q Sabre Lite boardJason Liu
Add the initial support for Freescale i.MX6Q Sabre Lite board Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com> Signed-off-by: Jason Liu <jason.hui@linaro.org> CC: Eric Nelson <eric.nelson@boundarydevices.com>
2012-01-16M28EVK: Fix build if CONFIG_CMD_NAND not selectedMarek Vasut
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Stefano Babic <sbabic@denx.de>
2012-01-16m28evk: Use GENERATED_GBL_DATA_SIZEFabio Estevam
Use GENERATED_GBL_DATA_SIZE for calculating CONFIG_SYS_INIT_SP_OFFSET. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-01-16mx28evk: Add initial support for MX28EVK boardFabio Estevam
Add initial support for Freescale MX28EVK board. Tested boot via SD card and by loading a kernel via TFTP through the FEC interface. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Marek Vasut <marek.vasut@gmail.com> Acked-by: Stefano Babic <sbabic@denx.de>
2012-01-16i.mx6q: arm2: Add the enet function supportJason Liu
This enable the network function on the i.mx6q armadillo2 board(arm2), thus we can use tftp to load image from network. Cc: Stefano Babic <sbabic@denx.de> Signed-off-by: Jason Liu <jason.hui@linaro.org> Tested-by: Dirk Behme <dirk.behme@de.bosch.com>
2012-01-13openrisc: Add openrisc-generic example boardStefan Kristiansson
Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
2012-01-13openrisc: Add architecture image supportStefan Kristiansson
Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
2012-01-13Merge branch 'master' of /home/wd/git/u-boot/custodiansWolfgang Denk
* 'master' of /home/wd/git/u-boot/custodians: fsl_lbc: add printout of LCRR and LBCR to local bus regs sbc8548: Fix up local bus init to be frequency aware sbc8548: enable support for hardware SPD errata workaround sbc8548: relocate fixed ddr init code to ddr.c file sbc8548: Make enabling SPD RAM configuration work sbc8548: Fix LBC SDRAM initialization settings sbc8548: enable ability to boot from alternate flash sbc8548: relocate 64MB user flash to sane boundary Revert "SBC8548: fix address mask to allow 64M flash" MPC85xxCDS: Fix missing LCRR_DBYP bits for 66-133MHz LBC eXMeritus HWW-1U-1A: Add support for the AT24C128N I2C EEPROM eXMeritus HWW-1U-1A: Minor environment variable tweaks
2012-01-13Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxWolfgang Denk
* 'master' of git://git.denx.de/u-boot-mpc85xx: fsl_lbc: add printout of LCRR and LBCR to local bus regs sbc8548: Fix up local bus init to be frequency aware sbc8548: enable support for hardware SPD errata workaround sbc8548: relocate fixed ddr init code to ddr.c file sbc8548: Make enabling SPD RAM configuration work sbc8548: Fix LBC SDRAM initialization settings sbc8548: enable ability to boot from alternate flash sbc8548: relocate 64MB user flash to sane boundary Revert "SBC8548: fix address mask to allow 64M flash" MPC85xxCDS: Fix missing LCRR_DBYP bits for 66-133MHz LBC eXMeritus HWW-1U-1A: Add support for the AT24C128N I2C EEPROM eXMeritus HWW-1U-1A: Minor environment variable tweaks
2012-01-13Merge branch 'master' of /home/wd/git/u-boot/custodiansWolfgang Denk
* 'master' of /home/wd/git/u-boot/custodians: fix: error ATMEL_FIO_BASE undeclared, if use I2C_Soft on AT91
2012-01-13Merge branch 'master' of git://git.denx.de/u-boot-i2cWolfgang Denk
* 'master' of git://git.denx.de/u-boot-i2c: fix: error ATMEL_FIO_BASE undeclared, if use I2C_Soft on AT91
2012-01-13Merge branch 'master' of /home/wd/git/u-boot/custodiansWolfgang Denk
* 'master' of /home/wd/git/u-boot/custodians: board/mpl/pati: use the CFI driver for the PATI board board/mpl/mip405: use the CFI driver for the MIP405/MIP405T board board/mpl/pip405: use the CFI driver for the PIP405 board board/mpl/common: remove the old legacy flash ppc4xx: Setup HICB on Io64
2012-01-13Merge branch 'master' of git://git.denx.de/u-boot-ppc4xxWolfgang Denk
* 'master' of git://git.denx.de/u-boot-ppc4xx: board/mpl/pati: use the CFI driver for the PATI board board/mpl/mip405: use the CFI driver for the MIP405/MIP405T board board/mpl/pip405: use the CFI driver for the PIP405 board board/mpl/common: remove the old legacy flash ppc4xx: Setup HICB on Io64
2012-01-13Merge branch 'master' of /home/wd/git/u-boot/custodiansWolfgang Denk
* 'master' of /home/wd/git/u-boot/custodians: mpc8313erdb: fix mtdparts address powerpc/83xx/km: add support for 8321 based tuge1 board powerpc/83xx/km: merge tuxa and tuda1 boards to tuxx1 powerpc/83xx/km: remove obsolete defines for tuda1 powerpc/83xx/km: update SDRAM parameters for km8321 boards mpc8313erdb: Enable GPIO support on the MPC8313E RDB mpc83xx: Add a GPIO driver for the MPC83XX family gpio: Replace ARM gpio.h with the common API in include/asm-generic gpio: Modify common gpio.h to more closely match Linux
2012-01-13Merge branch 'master' of git://git.denx.de/u-boot-mpc83xxWolfgang Denk
* 'master' of git://git.denx.de/u-boot-mpc83xx: mpc8313erdb: fix mtdparts address powerpc/83xx/km: add support for 8321 based tuge1 board powerpc/83xx/km: merge tuxa and tuda1 boards to tuxx1 powerpc/83xx/km: remove obsolete defines for tuda1 powerpc/83xx/km: update SDRAM parameters for km8321 boards mpc8313erdb: Enable GPIO support on the MPC8313E RDB mpc83xx: Add a GPIO driver for the MPC83XX family gpio: Replace ARM gpio.h with the common API in include/asm-generic gpio: Modify common gpio.h to more closely match Linux
2012-01-13Merge branch 'master' of /home/wd/git/u-boot/custodiansWolfgang Denk
* 'master' of /home/wd/git/u-boot/custodians: fsl_esdhc: fix PIO mode transfers mmc: tegra2: Implement card-detect hook. mmc: fsl_esdhc: Implement card-detect hook. mmc: Implement card detection. mmc: Change board_mmc_getcd() function prototype. drivers/mmc/mv_sdhci.c: Fix build warning ftsdc010: improve performance and capability mmc: add host_caps checking avoid switch card improperly i.mx: fsl_esdhc: add the i.mx6q support
2012-01-11sbc8548: enable support for hardware SPD errata workaroundPaul Gortmaker
Existing boards by default have an issue where the LBC SDRAM SPD EEPROM and the DDR2 SDRAM SPD EEPROM both land at 0x51. After the hardware modification listed in the README is made, then the DDR2 SPD EEPROM appears at 0x53. So this implements a board specific get_spd() by taking advantage of the existing weak linkage, that 1st tries reading at 0x53 and then if that fails, it falls back to the old 0x51. Since the old dependency issue of "SPD implies no LBC SDRAM" gets removed with the hardware errata fix, remove that restriction in the code, so both LBC SDRAM and SPD can be selected. Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2012-01-11sbc8548: relocate fixed ddr init code to ddr.c filePaul Gortmaker
Nothing to see here, just a relocation of the fixed ddr init sequence to live in the actual ddr.c file itself. Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2012-01-11sbc8548: Make enabling SPD RAM configuration workPaul Gortmaker
Previously, SPD configuration of RAM was non functional on this board. Now that the root cause is known (an i2c address conflict), there is a simple end-user workaround - remove the old slower local bus 128MB module and then SPD detection on the main DDR2 memory module works fine. We make the enablement of the LBC SDRAM support conditional on being not SPD enabled. We can revisit this dependency as the hardware workaround becomes available. Turning off LBC SDRAM support revealed a couple implict dependencies in the tlb/law code that always expected an LBC SDRAM address. This has been tested with the default 256MB module, a 512MB a 1GB and a 2GB, of varying speeds, and the SPD autoconfiguration worked fine in all cases. The default configuration remains to go with the hard coded DDR config, so the default build will continue to work on boards where people don't bother to read the docs. But the advantage of going to the SPD config is that even the small default module gets configured for CL3 instead of CL4. Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2012-01-11sbc8548: Fix LBC SDRAM initialization settingsPaul Gortmaker
These were cloned from the mpc8548cds platform which has a different memory layout (1/2 the size). Set the values by comparing to the register file for the board used during JTAG init sequence: LSDMR1 0x2863B727 /* PCHALL */ LSDMR2 0x0863B727 /* NORMAL */ LSDMR3 0x1863B727 /* MRW */ LSDMR4 0x4063B727 /* RFEN */ This differs from what was there already in that the RFEN is not bundled in all four steps implicitly, but issued once as the final step. The other difference seen when comparing vs. the register file init, is that since the memory is split across /CS3 and /CS4, the dummy writes need to go to 0xf000_0000 _and_ to 0xf400_0000. We also rewrite the final LBC SDRAM inits as macros, as there is no real need for them to be a local variable that is modified on the fly at runtime. Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2012-01-11sbc8548: enable ability to boot from alternate flashPaul Gortmaker
This board has an 8MB soldered on flash, and a 64MB SODIMM flash module. Normally the board boots from the 8MB flash, but the hardware can be configured for booting from the 64MB flash as well by swapping CS0 and CS6. This can be handy for recovery purposes, or for supporting u-boot and VxBoot at the same time. To support this in u-boot, we need to have different BR0/OR0 and BR6/OR6 settings in place for when the board is configured in this way, and a different TEXT_BASE needs to be used due to the larger sector size of the 64MB flash module. We introduce the suffix _8M and _64M for the BR0/BR6 and the OR0/OR6 values so it is clear which is being used to map what specific device. The larger sector size (512k) of the alternate flash needs a larger malloc pool, otherwise you'll get failures when running saveenv, so bump it up accordingly. Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2012-01-11sbc8548: relocate 64MB user flash to sane boundaryPaul Gortmaker
The current situation has the 64MB user flash at an awkward alignment; shifted back from 0xfc00_0000 by 8M, to leave an 8MB hole for the soldered on boot flash @ EOM. But to switch to optionally supporting booting off the 64MB flash, the 64MB will then be mapped at the sane address of 0xfc00_0000. This leads to awkward things when programming the 64MB flash prior to transitioning to it -- i.e. even though the chip spans from 0xfb80_0000 to 0xff7f_ffff, you would have to program a u-boot image into the two sectors from 0xfbf0_0000 --> 0xfbff_ffff so that it was in the right place when JP12/SW2.8 were switched to make the 64MB on /CS0. (i.e. the chip is only looking at the bits in mask 0x3ff_ffff) We also have to have three TLB entries responsible for dealing with mapping the 64MB flash due to this 8MB of misalignment. In the end, there is address space from 0xec00_0000 to 0xefff_ffff where we can map it, and then the transition from booting from one config to the other will be a simple 0xec --> 0xfc mapping. Plus we can toss out a TLB entry. Note that TLB0 is kept at 64MB and not shrunk down to the 8MB boot flash; this means we won't have to change it when the alternate config uses the full 64MB for booting, in TLB0. Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2012-01-11Revert "SBC8548: fix address mask to allow 64M flash"Paul Gortmaker
This reverts commit ccf1ad535ae1c0dc2d466235c668adbdfe3a55b7. The commit "SBC8548: fix address mask to allow 64M flash" essentially made this change: * OR6: - * Addr Mask = 64M = OR6[0:16] = 1111 1100 0000 0000 0 + * Addr Mask = 64M = OR6[0:16] = 1111 1000 0000 0000 0 But this makes no sense, as section 13.3.1.2.1 in the MPC8548ERM v2 clearly indicates the masks: 1111_1111_1000_0000_0 8 Mbytes 1111_1100_0000_0000_0 64 Mbytes 1111_1000_0000_0000_0 128 Mbytes So the original value was correct, and the commit was invalid, causing a 128MB mapping for a 64MB flash device. The problem rears its head when trying to configure u-boot to have access to both flash, since the default memory map is: FB80_0000 – FF7F_FFFF 32-bits 64MB FLASH SODIMM FF80_0000 – FFFF_FFFF 8-bits 8MB FLASH By extending the mapping of the 64MB flash to 128MB, it now conflicts with the normal 8MB boot flash, causing issues. Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2012-01-11eXMeritus HWW-1U-1A: Add support for the AT24C128N I2C EEPROMKyle Moffett
This EEPROM is hardware-write-protected and used to persist key information such as the serial number and MAC addresses even if the primary environment sector in NOR FLASH is overwritten. During manufacturing, the environment is initialized from Linux and then the key parameters copied to the EEPROM via U-Boot: env export -c -s 0x2000 $loadaddr serial# macaddr mac1addr mac2addr eeprom write $loadaddr 0x0000 0x2000 The chip is then locked via hardware for delivery. When doing a field U-Boot upgrade, the environment is erased and reset to the defaults to avoid problems with "hwconfig" changes, etc. After loading the new U-Boot image, the hardware data is reloaded: i2c dev 0 eeprom read $loadaddr 0x0000 0x2000 env import -c $loadaddr 0x2000 saveenv The first three commands are saved in the "restore_eeprom" variable for user convenience. (EG: "run restore_eeprom && saveenv") Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com> Cc: Andy Fleming <afleming@gmail.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2012-01-11eXMeritus HWW-1U-1A: Minor environment variable tweaksKyle Moffett
Most of the ethernet connections are internal links with specialized hardware and are not useful for "dhcp" or general-purpose networking; U-Boot should not be cycling through them. Force the primary external network interface in "ethprime" and disable the interface cycling with "ethrotate=no". Additionally, the environment variable "preboot" has its own config option and means something entirely different from what the HWW-1U-1A variable was intended for. Rename the board variable to "setbootargs" to avoid potential confusion. Finally, fix an incorrect address for the kernel in FLASH memory. Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com> Cc: Andy Fleming <afleming@gmail.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2012-01-11fix: error ATMEL_FIO_BASE undeclared, if use I2C_Soft on AT91esw@bus-elektronik.de
* Since AT91 name schema was changed to ATMEL_BASE_xxx, I2C_SOFT on AT91 devices fails with 'error: ATMEL_FIO_BASE undeclared' * change ATMEL_PIO_BASE to ATMEL_BASE_PIOA will fix this Signed-off-by: Jens Scharsig <esw@bus-elektronik.de>
2012-01-09mpc8313erdb: fix mtdparts addressScott Wood
Fix a copy-and-paste error when adapting mpc8315erdb mtdparts to mpc8313erdb. mtdids was already using the proper address on mpc8313erdb. Signed-off-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2012-01-09powerpc/83xx/km: add support for 8321 based tuge1 boardHolger Brunck
This board is similar to our tuxx1 target. But on this board there is only one application specific chip select configured. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> cc: Valentin Longchamp <valentin.longchamp@keymile.com> Acked-by: Heiko Schocher <hs@denx.de> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2012-01-09powerpc/83xx/km: merge tuxa and tuda1 boards to tuxx1Holger Brunck
These boards are from a u-boot point of view identical. So collect the two headerfiles to one, to decrease maintenance. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> cc: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Heiko Schocher <hs@denx.de> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2012-01-09powerpc/83xx/km: remove obsolete defines for tuda1Holger Brunck
CONFIG_SYS_LCRR is unused and CONFIG_SYS_LBC_LBCR is already defined in the common header file, so remove them. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> cc: Valentin Longchamp <valentin.longchamp@keymile.com> Acked-by: Heiko Schocher <hs@denx.de> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2012-01-09powerpc/83xx/km: update SDRAM parameters for km8321 boardsMarco Schmid
Measurements during HW basic test showed, that the SDRAM timing has to be optimized. This patch adapted these timings accordingly. Signed-off-by: Marco Schmid <marco.schmid@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com> cc: Valentin Longchamp <valentin.longchamp@keymile.com> Acked-by: Heiko Schocher <hs@denx.de> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2012-01-09mpc8313erdb: Enable GPIO support on the MPC8313E RDBJoe Hershberger
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Cc: Joe Hershberger <joe.hershberger@gmail.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2012-01-09gpio: Modify common gpio.h to more closely match LinuxJoe Hershberger
Change "int gp" to "unsigned gpio" Add request and free entry-points Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Cc: Joe Hershberger <joe.hershberger@gmail.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2012-01-09board/mpl/pati: use the CFI driver for the PATI boardDavid Müller
Signed-off-by: David Mueller <d.mueller@elsoft.ch> Signed-off-by: Stefan Roese <sr@denx.de>
2012-01-09board/mpl/mip405: use the CFI driver for the MIP405/MIP405T boardDavid Müller
Signed-off-by: David Mueller <d.mueller@elsoft.ch> Signed-off-by: Stefan Roese <sr@denx.de>
2012-01-09board/mpl/pip405: use the CFI driver for the PIP405 boardDavid Müller
Signed-off-by: David Mueller <d.mueller@elsoft.ch> Signed-off-by: Stefan Roese <sr@denx.de>
2012-01-09ppc4xx: Setup HICB on Io64Dirk Eibach
The FPGA High-Speed Interconnect Bus (HICB) is now setup by u-boot. Signed-off-by: Dirk Eibach <eibach@gdsys.de> Signed-off-by: Stefan Roese <sr@denx.de>
2012-01-08mmc: Implement card detection.Thierry Reding
Check for card detect each time an MMC/SD device is initialized. If card detection is not implemented, this code behaves as before and continues assuming a card is present. If no card is detected, has_init is reset for the MMC/SD device (to force initialization next time) and an error is returned. Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de> Tested-by: Jason Liu <jason.hui@linaro.org>
2012-01-08mmc: Change board_mmc_getcd() function prototype.Thierry Reding
The new API no longer uses the extra cd parameter that was used to store the card presence state. Instead, this information is returned via the function's return value. board_mmc_getcd() returns -1 to indicate that no card-detection mechanism is implemented; 0 indicates that no card is present and 1 is returned if it was detected that a card is present. The rationale for this change can be found in the following email thread: http://lists.denx.de/pipermail/u-boot/2011-November/110180.html In summary, the old API was not consistent with the rest of the MMC API which always passes a struct mmc as the first parameter. Furthermore the cd parameter was used to mean "card absence" in some implementations and "card presence" in others. Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de> Tested-by: Jason Liu <jason.hui@linaro.org>
2012-01-06Revert "common.h: remove value from bool defines"Wolfgang Denk
This reverts commit 914c9ee971924665c9d2927fe83d8d70060b1eb8 which is causing tons of build warnings like start.S:39:0: warning: "_LINUX_CONFIG_H" redefined [enabled by default] /home/wd/git/u-boot/work/include/common.h:28:0: note: this is the location of the previous definition /work/wd/tmp-ppc/nand_spl/board/freescale/mpc8315erdb/start.S:39:0: warning: "_LINUX_CONFIG_H" redefined [enabled by default] /home/wd/git/u-boot/work/include/common.h:28:0: note: this is the location of the previous definition etc. Signed-off-by: Wolfgang Denk <wd@denx.de>
2012-01-05ARM: highbank: enable networking and pxeRob Herring
This enables the XGMAC ethernet driver and networking related config options. Signed-off-by: Jason Hobbs <jason.hobbs@calxeda.com> Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2012-01-05net: add Calxeda xgmac driverRob Herring
This adds ethernet driver for Calxeda xgmac found on Highbank SOC. Signed-off-by: Rob Herring <rob.herring@calxeda.com> Fix: WARNING: __aligned(size) is preferred over __attribute__((aligned(size))) Signed-off-by: Wolfgang Denk <wd@denx.de>
2012-01-05Merge branch 'master' of git://git.denx.de/u-boot-armWolfgang Denk
* 'master' of git://git.denx.de/u-boot-arm: tegra2: Optimize out-of-tree build for Ventana. tegra: Move boards over to use arch-level board UART function tegra: Add support for UART init in cpu board.c tegra: Add a function mux feature tegra: add clock_ll_start_uart() to enable UART prior to reloc tegra: Move clock_early_init() to arch_cpu_init() tegra: Move cpu_init_cp15() to arch_cpu_init() arm: Tegra: Fix Harmony and Ventana builds in u-boot-tegra/master tegra: Fix build error in plutux, medcom tegra2: Add Avionic Design Medcom support. tegra2: Add Avionic Design Plutux support. tegra2: Add common Avionic Design Tamonten support. tegra2: Move tegra2_mmc_init() prototype to public header. tegra2: Change CONFIG_SYS_TEXT_BASE to 0x00108000. tegra2: Always build with USE_PRIVATE_LIBGCC=yes. tegra2: Plumb in SPI/UART switch code tegra2: spi: Support SPI / UART switch tegra2: Implement SPI / UART GPIO switch tegra2: Enable SPI environment on Seaboard tegra2: config: Enable SPI flash on Seaboard tegra2: spi: Add SPI driver for Tegra2 SOC tegra2: Add UARTB support tegra2: Tidy UART selection arm, davinci: Fix build warnings for cam_enc_4xx Devkit8000: Switch over to enable_gpmc_cs_config arm, davinci: Add support for generating AIS images to the Makefile mkimage: Fix variable length header support arm, da850evm: Add an SPL for SPI boot arm, davinci: Add SPL support for DA850 SoCs sf: Add spi_boot() to allow booting from SPI flash in an SPL spl: display_options.o is required for SPI flash support in SPL ARM: omap3: add support to Technexion twister board ARM: omap3: added common configuration for Technexion TAM3517 vision2: Fix checkpatch warning
2012-01-05env: remove value from boolean definesIgor Grinberg
Several boolean defines have a value assigned. Remove the value as defining the symbol is enough. Signed-off-by: Igor Grinberg <grinberg@compulab.co.il> Acked-by: Marek Vasut <marek.vasut@gmail.com> Acked-by: Mike Frysinger <vapier@gentoo.org>
2012-01-05common.h: remove value from bool definesIgor Grinberg
Several boolean defines have a value assigned. Remove the value as defining the symbol is enough. Signed-off-by: Igor Grinberg <grinberg@compulab.co.il> Acked-by: Mike Frysinger <vapier@gentoo.org>
2012-01-05fpga: add definition for Xilinx Spartan-6 XC6SLX4Stefano Babic
Signed-off-by: Stefano Babic <sbabic@denx.de>
2012-01-05phy: add phy_smsc_init() declarationVladimir Zapolskiy
This trivial change removes a compilation warning: ----8<---- phy.c: In function 'phy_init': phy.c:448:2: warning: implicit declaration of function 'phy_smsc_init' ----8<---- Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Acked-by: Marek Vasut <marek.vasut@gmail.com>
2011-12-24arm: Tegra: Fix Harmony and Ventana builds in u-boot-tegra/masterTom Warren
Seaboard changes have removed the need for common/board.o in the Makefile. Propagate this change to the other Tegra2 builds. Signed-off-by: Tom Warren <twarren@nvidia.com>
2011-12-24tegra: Fix build error in plutux, medcomSimon Glass
We need to define CONFIG_ENV_IS_NOWHERE to avoid this error: cmd_nvedit.c:69:3: error: #error Define one of CONFIG_ENV_IS_IN_... Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
generated by cgit (git 2.34.1) at 2025-01-09 08:20:53 +0000