| Age | Commit message (Collapse) | Author |
|---|
|
Add bootstage IDs for board init and LCD.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
It is useful to be able to write the bootstage information to memory for
use by a later utility, or the Linux kernel. Provide a function to do
this as well as a function to read bootstage information back and incorporate
it into the current table.
This also makes it possible for U-Boot to chain to another U-Boot and pass
on its bootstage information.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Add an option, CONFIG_BOOTSTAGE_FDT to pass boot timings to the kernel
in the device tree, if available. To use this, you must have
CONFIG_OF_LIBFDT defined.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Sometimes we want to add up the amount of time spent in a particular
activity when it is happening in a number of discrete chunks.
Add bootstage_start() to mark the start of an acitivity and
bootstage_accum() to accumulate the time since the last start. Calling
these function in pairs results in the accumulated time being collected.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
This function is not static, but not exported either. Add a prototype
in the header file and move the required enum to the header also.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Signed-off-by: Lei Wen <leiwen@marvell.com>
|
|
Add a new config CONFIG_GZIP_ENABLED, if enabled, the uboot bin would
include zlib's deflate method which could be used for compressing.
Signed-off-by: Lei Wen <leiwen@marvell.com>
|
|
|
|
Signed-off-by: Tom Rini <trini@ti.com>
|
|
On some system (e.g. powerpc), the load-address and entry-point is
located at address 0. So the current approach to load the image
(payload) including the header to the address "load-address - 64"
can't work here.
This patch adds an flag to skip this copying including header to
the SPL framework. By setting SPL_COPY_PAYLOAD_ONLY, only the
playload will be copied. This will be used by the SPL NOR flash
driver on powerpc.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
|
|
SPL NOR flash booting support is quite simple. Only copying of the
images is needed.
On MPC5xxx we need to make sure to only use the standard memcpy()
implementation and not the MPC5xxx specific one. As the MPC5xxx
version has some complexity which is not needed for this SPL
booting.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
|
|
The common spl framework expects the u-boot payload size through
CONFIG_SYS_MONITOR_LEN. Define the macro with the u-boot's size. With
this change, CONFIG_SYS_NAND_U_BOOT_SIZE is no longer required. Delete
the same.
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com>
|
|
- Convert the non-relocation part of board_init_f to spl_board_init, turn on CONFIG_SPL_BOARD_INIT in the configs.
- Remove duplicated code.
- Add spl_boot_device() that returns the statically chosen boot device.
Signed-off-by: Tom Rini <trini@ti.com>
|
|
This patch add support for the configuration of an external switch from
the 88E6xxx series from Marvell trough an MDIO link using indirect
adressing. This can be used if we do not want to use an EEPROM for the
configuration.
This driver is not generic and was not tested on other switches than the
88e6352. This is proposed as a first implementation that is somewhat
limited but works and that can be used as a basis for further
developments for this switch family.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
cc: Joe Hershberger <joe.hershberger@gmail.com>
|
|
In SPL (CONFIG_SPL_FRAMEWORK) board_init_f must setup the stack pointer,
clear the BSS and call board_init_r. We mark this as weak as some
platforms may need to perform additional initalization at this point.
We provide a gd that we know will be in a usable location, once the BSS
has been cleared to help with this as well. Finally, we no longer call
relocate_code so remove that from the armv7 version.
Next, both board_init_f and jump_to_image_linux are going to be
inherently arch-specific, so move these versions to arch/arm/lib/spl.c
Signed-off-by: Tom Rini <trini@ti.com>
|
|
Add a new flag, CONFIG_SPL_FRAMEWORK to opt into the common/spl SPL
framework, enable on all of the previously using boards. We move the
spl_ymodem.c portion to common/ and spl_mmc.c to drivers/mmc/. We leave
the NAND one in-place as we plan to replace it later in this series.
We use common/spl to avoid linker problems with respect to merging
constant strings in objects. Otherwise all strings in common/ will be
linked in and kept which grows SPL in size too much.
Signed-off-by: Tom Rini <trini@ti.com>
|
|
This is an OMAP/related-specific function, move calling it to
spl_board_init() and turn on CONFIG_SPL_BOARD_INIT on the boards that
enabled NAND and didn't enable this already.
Signed-off-by: Tom Rini <trini@ti.com>
|
|
Only omap4/5 currently have a meaningful set of display text and overo
had been adding a function to display nothing. Change how this works to
be opt-in and only turned on for omap4/5 now.
Signed-off-by: Tom Rini <trini@ti.com>
|
|
When storage devices contain files larger than the embedded RAM, it is
useful to be able to read these files by chunks, e.g. for a software
update to the embedded NAND Flash from an external storage device (USB
stick, SD card, etc.).
Hence, this patch makes it possible by adding a new FAT API to read
files from a given position. This patch also adds this feature to the
fatload command.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
|
|
Declare malloc_bin_reloc() in malloc.h and remove all extern declarations
in various board.c files to get rid of one checkpatch.pl warning.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Andreas Bießmann <andreas.devel@gmail.com>
Cc: Jason Jin <Jason.jin@freescale.com>
Cc: Macpaul Lin <macpaul@andestech.com>
Cc: Daniel Hellstrom <daniel@gaisler.com>
Acked-by: Andreas Bießmann <andreas.devel@gmail.com>
|
|
Device driver for Zynq Gem IP.
Signed-off-by: Michal Simek <monstr@monstr.eu>
CC: Joe Hershberger <joe.hershberger@gmail.com>
CC: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
|
|
Avoid clutter in ueth_data. Individual drivers should not mess
with structures belonging to the core like this.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
Each EFI partition table entry contains a UUID. Extend U-Boot's struct
disk_partition to be able to store this information, and modify
get_partition_info_efi() to fill it in.
The implementation of uuid_string() was derived from the Linux kernel,
tag v3.6-rc4 file lib/vsprintf.c function uuid_string().
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Rework get_device_and_partition() to:
a) Implement a new partition ID of "auto", which requests that U-Boot
search for the first "bootable" partition, and fall back to the first
valid partition if none is found. This way, users don't need to
specify an explicit partition in their commands.
b) Make use of get_device().
c) Add parameter to indicate whether returning a whole device is
acceptable, or whether a partition is mandatory.
d) Make error-checking of the user's device-/partition-specification
more complete. In particular, if strtoul() doesn't convert all
characters, it's an error rather than just ignored.
The resultant device/partition returned by the function will be as
follows, based on whether the disk has a partition table (ptable) or not,
and whether the calling command allows the whole device to be returned
or not.
(D and P are integers, P >= 1)
D
D:
No ptable:
!allow_whole_dev: error
allow_whole_dev: device D
ptable:
device D partition 1
D:0
!allow_whole_dev: error
allow_whole_dev: device D
D:P
No ptable: error
ptable: device D partition P
D:auto
No ptable:
!allow_whole_dev: error
allow_whole_dev: device D
ptable:
first partition in device D with bootable flag set.
If none, first valid paratition in device D.
Note: In order to review this patch, it's probably easiest to simply
look at the file contents post-application, rather than reading the
patch itself.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
[swarren: Rob implemented scanning for bootable partitions. I fixed a
couple of issues there, switched the syntax to ":auto", added the
error-checking rework, and ":0" syntax for the whole device]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
This patch introduces function get_device(). This looks up a
block_dev_desc_t from an interface name (e.g. mmc) and device number
(e.g. 0). This function is essentially the non-partition-specific
prefix of get_device_and_partition().
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Convert reiserload and reiserls to use common device and partition parsing
function. With the common function "dev:part" can come from the
environment and a '-' can be used in that case.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
|
|
Convert zfsload and zfsls to use common device and partition parsing
function. With the common function "dev:part" can come from the
environment and a '-' can be used in that case.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
|
|
Convert ext2/4 load, ls, and write functions to use common device and
partition parsing function. With the common function "dev:part" can come
from the environment and a '-' can be used in that case.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
|
|
There's no real need to expose this and it can be removed by using a static
allocation.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
|
|
All block device related commands (scsiboot, fatload, ext2ls, etc.) have
simliar duplicated device and partition parsing and selection code. This
adds a common function to replace various implementations.
The new function has an enhancement over current versions. If no device
or partition is specified on the command line, the bootdevice env variable
will be used (scsiboot does this).
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
|
|
Determine which partitions are bootable/active. In the partition listing,
print "Boot" for partitions with the bootable/active flag set.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
|
|
All the raw block load commands duplicate the same code. Starting with
the ide version as it has progress updates convert ide, usb, and scsi boot
commands to all use a common version.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
|
|
|
|
Check the incoming packets' source IP address... if ncip isn't set to a
broadcast address, only listen to the client at ncip.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
Previously u-boot would initialize the network interface for every
network operation and then shut it down again. This makes sense for
most operations where the network in not known to be needed soon after
the operation is complete. In the case of netconsole, it will use the
network for every interaction with the shell or every printf. This
means that the network is being reinitialized very often. On many
devices, this intialization is very slow.
This patch checks for consecutive netconsole actions and leaves the
ethernet hardware initialized between them. It will still behave the
same old way for all other network operations and any time another
network operation happens between netconsole operations.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
|
|
|
|
|
|
This makes it easier to include this header from other headers.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
|
|
This function should also be part of the GPIO API, so add it.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
|
|
Update Makefile change for LIBS -> LIBS-y change.
Conflicts:
Makefile
Signed-off-by: Tom Rini <trini@ti.com>
|
|
This patch fixes the build error for MCF537x. As the NANDFLASH_SIZE is
redefined in boards.cfg, it is needed to rename NANDFLASH_SIZE into
CONFIG_NANDFLASH_SIZE in include/configs/M5373EVB.h.
Signed-off-by: Alison Wang <b18965@freescale.com>
|
|
|
|
Add support for the onboard eSDHC MMC controller. The hardware on the
MPC8308RDB has the following errata:
- ESDHC111: manual asynchronous CMD12 is broken
- DMA is broken (PIO works)
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
[added include fsl_esdhc header to prevent implicit declarations of
fsl_esdhc_mmc_init() and fdt_fixup_esdhc()]
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
This is very useful on a modern system.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
The SPI pins are routed to header J8 for testing SPI functionality. A
Spansion flash has been wired up and tested on this header.
This patch breaks support for the second TSEC interface, since the GPIO
pin used as a chip select is pinmuxed with some of the TSEC pins.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
Change the syntax (user API) for "env default":
-f: override write-once variables
var... : accept individual variable(s)
-a: all (resetting the whole env is NOT the default behavior)
Enable variable checking and make changes effective by
enabling do_apply argument to himport_r().
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
|
|
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Reviewed-by: Marek Vasut <marex@denx.de>
|
|
Change hashtable so that a callback function will decide whether a
variable can be overwritten, and possibly apply the changes.
So add a new field to struct hsearch_data:
o "apply" callback function to check whether a variable can be
overwritten, and possibly immediately apply the changes;
when NULL, no check is performed.
And a new argument to himport_r():
o "do_apply": whether to call the apply callback function
NOTE: This patch does not change the current behavior.
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Reviewed-by: Marek Vasut <marex@denx.de>
|
|
Add 2 new arguments to himport_r():
o "nvars", "vars": number and list of variables to take into account
(0 means ALL)
NOTE: This patch does not change the current behaviour.
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Reviewed-by: Marek Vasut <marex@denx.de>
|
