| Age | Commit message (Collapse) | Author |
|---|
|
Most architectures currently supported by U-Boot use trivial
implementations of map_to_physmem & virt_to_phys which simply cast a
physical address to a pointer for use a virtual address & vice-versa.
This results in a lot of duplicate implementations of these mapping
functions.
The set of functions provided by different architectures also differs,
with some having implementations of phys_to_virt & others not. A later
patch will make use of phys_to_virt in architecture-neutral code, and so
requires that it be provided for all architectures.
This patch introduces an asm-generic/io.h which provides generic
implementations of address mapping functions, allowing the duplication
of them between architectures to be removed. Once architectures are
converted to make use of this generic header it will also ensure that
all of phys_to_virt, virt_to_phys, map_physmem & unmap_physmem are
provided. The 2 families of functions differ in that map_physmem may
create dynamic mappings whilst phys_to_virt may not & therefore is more
limited in scope but doesn't require information such as a length &
flags.
This patch doesn't convert any architectures to make use of this generic
header - later patches in the series will do so.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Alexey Brodkin <alexey.brodkin@synopsys.com>
Cc: Angelo Dureghello <angelo@sysam.it>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Macpaul Lin <macpaul@andestech.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Thomas Chou <thomas@wytron.com.tw>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Angelo Dureghello <angelo@sysam.it>
Tested-by: Angelo Dureghello <angelo@sysam.it>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
|
|
Signed-off-by: Marek Behun <marek.behun@nic.cz>
create mode 100644 fs/btrfs/Kconfig
create mode 100644 fs/btrfs/Makefile
create mode 100644 fs/btrfs/btrfs.c
create mode 100644 include/btrfs.h
|
|
Add a header variadic-macro.h which defines the CALL_MACRO_FOR_EACH marco.
This macro can be used as follows:
#define TEST(x)
CALL_MACRO_FOR_EACH(TEST, a, b, c, d)
This will expand to
TEST(a) TEST(b) TEST(c) TEST(d)
The nice thing is that CALL_MACRO_FOR_EACH is a variadic macro, thus the
number of arguments can vary (although it has an upper limit - in this
implementation 32 arguments).
Signed-off-by: Marek Behun <marek.behun@nic.cz>
create mode 100644 include/u-boot/variadic-macro.h
|
|
The ext4, reiserfs and zfs filesystems all have their own implementation
of the same function, *_devread. Generalize this function into fs_devread
and put the code into fs/fs_internal.c.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
[trini: Move fs/fs_internal.o hunk to the end of fs/Makefile as all
cases need it]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This is needed for BTRFS.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
create mode 100644 lib/crc32c.c
|
|
|
|
|
|
USB endpoint reports the period between consecutive requests to send
or receive data as bInverval in its endpoint descriptor. So far this
is ignored by xHCI driver and the 'Interval' field in xHC's endpoint
context is always programmed to zero which means 1ms for low speed
or full speed , or 125us for high speed or super speed. We should
honor the interval by getting it from endpoint descriptor.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
|
|
With the root hub unbinding in usb_stop(), there is no need to do
a Sandbox-specific reset operation. usb_emul_reset() is no longer
used anywhere, drop it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
|
|
This can be useful outside of the sandbox usb emulation uclass
driver. Expose it as a public API with a proper prefix (usb_emul_).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Current emulator select logic in usb_emul_find_devnum() is to test
the USB address. The USB address of the device being enumerated is
initialized to zero at the beginning of the enumeration process in
usb_setup_device(). At this point, the saved USB address in the
platform data has not been assigned to any valid USB address either.
This means: the logic will select an emulator device according to
its sequence of declaring order in the device tree. Take test.dts
for example, flash-stick@0 will be selected before flash-stick@1.
But unfortunately such logic is wrong.
In fact USB devices show up in a random order during the enumeration
which means usb_emul_find_devnum() may be called on port 3 for keyb@3
before on port 0 for flash-stick@0.
To fix this, we introduce a new emulator uclass specific platdata
to store the USB device's port number on its parent hub, and update
the logic to test the port number instead.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
|
|
There is no such a parameter called 'bus'.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
|
|
This parameter is never used.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Patch queue for efi - 2017-10-01
Lots of new things this time. High level highlights are:
- Shim support (to boot Fedora)
- Initial set of unit tests
- Preparations to support UEFI Shell
|
|
CONFIG_ENV_OFFSET is already defined in
include/configs/rockchip-common.h
For CONFIG_ROCKCHIP_BACK_TO_BROM=y we redefine CONFIG_ENV_OFFSET
to an unsuitable value. We were lucky to get a compiler warning.
Remove the incorrect redefinition.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
Add Falcon mode support in vyasa rk3288 board.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
Since the size of SPL can't be exceeded 0x8000 bytes in RK3288,
it is not possible add new SPL features like Falcon mode or etc.
So add TPL stage so-that adding new features to SPL is possible.
- TPL: DRAM init, clocks
- SPL: MMC, falcon, etc
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
The clk_saradc is dividing from the 24M, clk_saradc=24MHz/(saradc_div_con+1).
SARADC integer divider control register is 10-bits width.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
Add tracing printings to Linux/Android boot commands, so that we can see
what's going on. Helps to trace possible bugs on early stages and
improves the output for user (which is especially useful, because we
have a bunch of boot commands executing one by one).
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Extract commands for booting Linux from eMMC to separate command. It
seems more logical that way, and allows us to run the whole command set
from U-Boot shell with only one command.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Right now on OMAP5-based boards we have only one partition defined for
Linux boot, which is rootfs. That doesn't work with bootpart=1:2 (that
is defined in include/environment/ti/boot.h). To fix Linux boot we may
either:
1. Change bootpart to be 1:1
2. Or add preceding partition, so that rootfs is actually 1:2
Second choice seems more reasonable, as DFU is already using similar
partition table and can rely on bootpart to be 1:2.
This patch adds "bootloader" partition. So now eMMC layout for Linux
boot looks like this:
offset content size partition
(KiB) (KiB)
Reviewed-by: Tom Rini <trini@konsulko.com>
=======================================================================
0 +--------------------------------+
| MBR/GPT header | 128 -
128 +--------------------------------+
| MLO | 256 -
384 +--------------------------------+
| u-boot.img | 1792 bootloader
2176 +--------------------------------+
| //////////// hole //////////// | 256 -
2432 +--------------------------------+
| U-Boot environment | 128 -
2560 +--------------------------------+
| U-Boot environment (redundant) | 128 -
2688 +--------------------------------+
| rootfs | remaining rootfs
end +--------------------------------+
=======================================================================
Guard hole appears because U-Boot environment offset was calculated for
Android partition table, which has two additional partitions in place of
that hole ("environment" and "misc" partitions).
This patch also changes rootfs offset from 2 MiB further to 2688 KiB,
so that there won't be any collisions with U-Boot environment when we
flash rootfs.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
|
|
Right now on OMAP5-based boards we have only one partition defined for
Linux boot, which is rootfs. That doesn't work with bootpart=1:2 (that
is defined in include/environment/ti/boot.h). To fix Linux boot we may
either:
1. Change bootpart to be 1:1
2. Or add preceding partition, so that rootfs is actually 1:2
Second choice seems more reasonable, as DFU is already using similar
partition table and can rely on bootpart to be 1:2.
This patch adds "bootloader" partition. So now eMMC layout for Linux
boot looks like this:
offset content size partition
(KiB) (KiB)
Reviewed-by: Tom Rini <trini@konsulko.com>
=======================================================================
0 +--------------------------------+
| MBR/GPT header | 128 -
128 +--------------------------------+
| MLO | 256 -
384 +--------------------------------+
| u-boot.img | 1792 bootloader
2176 +--------------------------------+
| //////////// hole //////////// | 256 -
2432 +--------------------------------+
| U-Boot environment | 128 -
2560 +--------------------------------+
| U-Boot environment (redundant) | 128 -
2688 +--------------------------------+
| rootfs | remaining rootfs
end +--------------------------------+
=======================================================================
Guard hole appears because U-Boot environment offset was calculated for
Android partition table, which has two additional partitions in place of
that hole ("environment" and "misc" partitions).
This patch also changes rootfs offset from 2 MiB further to 2688 KiB,
so that there won't be any collisions with U-Boot environment when we
flash rootfs.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
|
|
Now the u-boot spi image is greater than 0x80000, increase the same
in env during spi erase.
Reported-by: Yan Liu <yan-liu@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
On all other platforms the command 'findfdt' populates the variable
'fdtfile', but on K2G we only populate 'name_fdt'. The generic boot
and automation scripts fail when 'findfdt' is not populated, fix
this for K2G.
Signed-off-by: Andrew F. Davis <afd@ti.com>
|
|
On secure devices the initial secure software may install a firewall at
the end of DRAM, define protected RAM to avoid space.
Signed-off-by: Andrew F. Davis <afd@ti.com>
|
|
With the device tree ported from Linux 4.13, this enables
Driver Model and Device Tree support for the am3517-evm
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Derald D. Woods <woods.technical@gmail.com>
|
|
With DM now enabled with the device tree pulled from Linux, we can
enable DM_I2C in U-Boot.
Reviewed-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Add DM_I2C_COMPAT to da850_am18xxevm to fix warning]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
There is a discrepency between U-Boot and Linux on the partition map.
This enabes the MTD parts to pass MTD partition information from U-Boot to
Linux. Linux already has a pending patch to enable MTD PARTS in
davinci_all_defconfig
Reviewed-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
|
|
With the device tree ported and DM compatible drivers, enable:
OF_CONTROL, DM_SPI, DM_SPI_FLASH and DM_SERIAL
Note: DM_SERIAL is not enabled for da850evm_direct_nor_defconfig
yet.
Reviewed-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
|
|
The HCD may have limitation on the maximum bytes to be transferred
in a USB transfer. USB class driver needs to be aware of this.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
|
|
|
|
|
|
The status register is optional in the AMD command sets, but it's
presence can be checked by reading out CFI table entry 0xc bit 0.
If the register is present, prefer using it's bit 7 to determine
if the flash is busy over reading the flash ; this is needed ie.
on Hyperflash memories.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Embed the flash base into struct flash_info instead of having ad-hoc
static array in the code. This does not only remove static variable,
but also allows CFI-like controllers, ie. HyperFlash ones, to use most
of the CFI flash code by populating the flash_info with matching base
address.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
This converts the following to Kconfig:
CONFIG_MVNETA
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
|
|
|
|
CONFIG_NAND_DENALI select's CONFIG_SYS_NAND_SELF_INIT, so the
NAND initialization process is driven by the driver itself.
CONFIG_SYS_NAND_MAX_CHIPS and CONFIG_SYS_NAND_BASE are unused.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Current u-boot disables IFC support for SD boot on all ls1043a
boards. Actually IFC only conflicts with QSPI on ls1043a hardware.
Only when QSPI is used, IFC should be disabled. Otherwise,
the u-boot with ls1043aqds_sdcard_ifc_defconfig would not work.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
For most of ls2080ardb use-cases, mc private DRAM block is required
to be of 1.75GB.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
[YS: this reservation needs to be reduced if memory is not enough]
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
As per updated board design, different QSPI flash
is connected on boards, hence change QSPI flash type
from Micron n25q512a device to spansion s25fs512s
device in dts and config.
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
CONFIG_DISPLAY_BOARDINFO_LATE config is used to delay
the prints of boardinfo late in cycle during uboot boot.
This feature is not required in case of QSPI_BOOT.
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Commit a8ecb39e accidentally reverted config macro CONFIG_ARCH_LS1021A
to CONFIG_LS102XA.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
dev_read_string_count() is used to get the number of strings in a
stringlist.
dev_read_string_index() is used to get a string in the stringlist based on
its position in the list.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
|
|
This patch adds support for stm32h7 soc family, stm32h743
discovery and evaluation boards.
For more information about STM32H7 series, please visit:
http://www.st.com/en/microcontrollers/stm32h7-series.html
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This patch adapts stm32h743 disco and eval dts files to match
with U-boot requirements or add features wich are not yet
upstreamed on kernel side :
_ Add RCC clock driver node and update all clocks phandle
accordingly.
By default, on kernel side, all clocks was temporarly
configured as a phandle to timer_clk waiting for a RCC
clock driver to be available.
On U-boot side, we now have a dedicated RCC clock driver, we
can configured all clocks as phandle to this driver.
All this binding update will be available soon in a kernel tag,
as all the bindings have been acked by Rob Herring [1].
[1] http://lkml.iu.edu/hypermail/linux/kernel/1704.0/00935.html
_ Align STM32H7 serial compatible string with the one which will be
available in next kernel tag. The bindings has been acked by
Rob Herring [2].
This compatible string will be usefull to add stm32h7 specific
feature for this serial driver.
[2] https://lkml.org/lkml/2017/7/17/739
_ Add gpio compatible and aliases for stm32h743
_ Add FMC sdram node with associated new bindings value to
manage second bank (ie bank 1).
_ Add missing HSI and CSI oscillators nodes needed
by STM32H7 RCC clock driver.
Clock sources could be:
_ HSE (High Speed External)
_ HSI (High Speed Internal)
_ CSI (Low Power Internal)
These clocks can be used as clocksource in some configuration.
By default, HSE is selected as clock source.
_ Set HSE to 25Mhz for stm32h743i-disco and eval board
By default, the external oscillator frequency is defined at
25 Mhz in SoC stm32h743.dtsi file.
It has been set at 125 Mhz in kernel DT temporarly waiting for
RCC clock driver becomes available.
As in U-boot we got a RCC clock driver, the real value of HSE
clock can be used.
_ Add "u-boot,dm-pre-reloc" for rcc, fmc, fixed-clock, pinctrl,
pwrcfg and gpio nodes.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
All these files are imported from linux kernel v4.13
Add device tree support for STM32H743 SoC and discovery
board. This board offers :
_ STM32H743XIH6 microcontroller with 2 Mbytes of
Flash memory and 1 Mbyte of RAM in TFBGA240+25 package
_ 5.7” 640x480 TFT color LCD with touch screen
_ Ethernet compliant with IEEE-802.3-2002
_ USB OTG HS
_ I2 C compatible serial interface
_ ST-MEMS digital microphones
_ 8-Gbyte (or more) SDIO3.0 interface microSD™ card
_ 8Mx32bit SDRAM
_ 1-Gbit Twin Quad-SPI NOR Flash
_ Reset, wakeup, or key buttons
_ Joystick with 4-direction control and selector
_ Board connectors :
1 USB with Micro-AB
Ethernet RJ45
Stereo headset jack including analog microphone input
microSD™ card
RCA connector
JTAG/SWD and ETM trace
_ Expansion connectors:
Arduino Uno compatible Connectors
2 x PIO connectors (PMOD and PMOD+)
_ On-board ST-LINK/V2-1 debugger/programmer with USB re-enumeration
capability: mass storage, virtual COM port and debug port
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This driver is adapted from linux drivers/reset/reset-stm32.c
It's compatible with STM32 F4/F7/H7 SoCs.
This driver doesn't implement .of_match as it's binded
by MFD RCC driver.
To add support for each SoC family, a SoC's specific
include/dt-binfings/mfd/stm32xx-rcc.h file must be added.
This patch only includes stm32h7-rcc.h dedicated for STM32H7 SoCs.
Other SoCs support will be added in the future.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This driver implements basic clock setup, only clock gating
is implemented.
This driver doesn't implement .of_match as it's binded
by MFD RCC driver.
Files include/dt-bindings/clock/stm32h7-clks.h and
doc/device-tree-bindings/clock/st,stm32h7-rcc.txt
will be available soon in a kernel tag, as all the
bindings have been acked by Rob Herring [1].
[1] http://lkml.iu.edu/hypermail/linux/kernel/1704.0/00935.html
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This patch adds the ST glue logic to manage the DWC3 HC
on STiH407 SoC family. It configures the internal glue
logic and syscfg registers.
Part of this code been extracted from kernel.org driver
(drivers/usb/dwc3/dwc3-st.c)
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
