From 2906845a1faf52a1db177b153f4353be804ef421 Mon Sep 17 00:00:00 2001 From: York Sun Date: Wed, 26 Jan 2011 10:30:00 -0800 Subject: p1022ds: fix pixis_reset altbank Fix the bits for ngpixis to reset to alternative bank. Originally the mask was 0xE0, which left it possible to reset to bank 3 if DIP switch is set to boot from bank 1. Changing to 0xF0 gurantees to reset to bank 2. Signed-off-by: York Sun Signed-off-by: Kumar Gala --- include/configs/P1022DS.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/include/configs/P1022DS.h b/include/configs/P1022DS.h index f31076858e..cb240418fe 100644 --- a/include/configs/P1022DS.h +++ b/include/configs/P1022DS.h @@ -151,7 +151,7 @@ #define CONFIG_SYS_OR2_PRELIM (OR_AM_32KB | 0x6ff7) #define PIXIS_LBMAP_SWITCH 7 -#define PIXIS_LBMAP_MASK 0xE0 +#define PIXIS_LBMAP_MASK 0xF0 #define PIXIS_LBMAP_ALTBANK 0x20 #define CONFIG_SYS_INIT_RAM_LOCK -- cgit From a14a94469c21feebad34e37d4881110e1469f415 Mon Sep 17 00:00:00 2001 From: Alex Dubov Date: Sun, 23 Jan 2011 21:59:10 -0800 Subject: mpq101: initial support for Mercury Computer Systems MPQ101 board Mpq101 is a RapidIO development board in AMC form factor, featuring MPC8548 processor, 512MB of hardwired DDR2 RAM, 128MB of hardwired NAND flash memory, real time clock and additional serial EEPROM on i2c bus (enabled). USB controller is available, but not presently enabled. Additional board information is available at: http://www.mc.com/products/boards/ensemble_mpq101_rapidio_powerquicc_iii.aspx Environment is configured to precede the actual u-boot image so that it's located at the beginning of flash erase block (made necessary by the recent changes to the embedded environment handling). This is achieved by means of custom ld script. Signed-off-by: Alex Dubov Signed-off-by: Kumar Gala --- MAINTAINERS | 4 + board/mercury/mpq101/Makefile | 53 ++++++ board/mercury/mpq101/law.c | 52 ++++++ board/mercury/mpq101/mpq101.c | 129 +++++++++++++ board/mercury/mpq101/tlb.c | 82 +++++++++ board/mercury/mpq101/u-boot.lds | 132 ++++++++++++++ boards.cfg | 1 + include/configs/mpq101.h | 394 ++++++++++++++++++++++++++++++++++++++++ 8 files changed, 847 insertions(+) create mode 100644 board/mercury/mpq101/Makefile create mode 100644 board/mercury/mpq101/law.c create mode 100644 board/mercury/mpq101/mpq101.c create mode 100644 board/mercury/mpq101/tlb.c create mode 100644 board/mercury/mpq101/u-boot.lds create mode 100644 include/configs/mpq101.h diff --git a/MAINTAINERS b/MAINTAINERS index edd1c5cd2a..14d06ca0c5 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -138,6 +138,10 @@ Jon Diekema sbc8260 MPC8260 +Alex Dubov + + mpq101 MPC8548 + Dirk Eibach devconcenter PPC460EX diff --git a/board/mercury/mpq101/Makefile b/board/mercury/mpq101/Makefile new file mode 100644 index 0000000000..58bc1b3f1f --- /dev/null +++ b/board/mercury/mpq101/Makefile @@ -0,0 +1,53 @@ +# +# Copyright 2007 Freescale Semiconductor, Inc. +# (C) Copyright 2001-2006 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).o + +COBJS-y += $(BOARD).o +COBJS-y += law.o +COBJS-y += tlb.o + +SRCS := $(SOBJS:.o=.S) $(COBJS-y:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS-y)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(obj).depend $(OBJS) $(SOBJS) + $(call cmd_link_o_target, $(OBJS)) + +clean: + rm -f $(OBJS) $(SOBJS) + +distclean: clean + rm -f $(LIB) core *.bak .depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/mercury/mpq101/law.c b/board/mercury/mpq101/law.c new file mode 100644 index 0000000000..0e23a6aabd --- /dev/null +++ b/board/mercury/mpq101/law.c @@ -0,0 +1,52 @@ +/* + * Copyright 2008 Freescale Semiconductor, Inc. + * + * (C) Copyright 2000 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include +#include + +/* + * LAW(Local Access Window) configuration: + * + * 0x0000_0000 0x1fff_ffff DDR SYS_SDRAM_SIZE + * 0xc000_0000 0xdfff_ffff RapidIO (set elsewhere) 512M + * 0xe000_0000 0xe000_ffff CCSR (set elsewhere) 1M + * 0xf000_0000 0xffff_ffff LBC options + FLASH 256M + * + * Notes: + * CCSRBAR and L2-as-SRAM don't need a configured Local Access Window. + * If flash is 8M at default position (last 8M), no LAW needed. + * + * LAW 0 is reserved for boot mapping + */ + +struct law_entry law_table[] = { + SET_LAW(CONFIG_SYS_SDRAM_BASE, CONFIG_SYS_SDRAM_SIZE_LOG - 1, + LAW_TRGT_IF_DDR_1), + SET_LAW(CONFIG_SYS_LBC_OPTION_BASE_PHYS, LAW_SIZE_256M, + LAW_TRGT_IF_LBC) +}; + +int num_law_entries = ARRAY_SIZE(law_table); diff --git a/board/mercury/mpq101/mpq101.c b/board/mercury/mpq101/mpq101.c new file mode 100644 index 0000000000..e02e87f111 --- /dev/null +++ b/board/mercury/mpq101/mpq101.c @@ -0,0 +1,129 @@ +/* + * (C) Copyright 2011 Alex Dubov + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include + +/* + * Initialize Local Bus + */ +void local_bus_init(void) +{ + fsl_lbc_t *lbc = LBC_BASE_ADDR; + + out_be32(&lbc->ltesr, 0xffffffff); /* Clear LBC error interrupts */ + out_be32(&lbc->lteir, 0xffffffff); /* Enable LBC error interrupts */ +} + +int checkboard(void) +{ + ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + ccsr_local_ecm_t *ecm = (void *)(CONFIG_SYS_MPC85xx_ECM_ADDR); + + puts("Board: Mercury Computer Systems, Inc. MPQ-101 "); +#ifdef CONFIG_PHYS_64BIT + puts("(36-bit addrmap) "); +#endif + putc('\n'); + + /* + * Initialize local bus. + */ + local_bus_init(); + + /* + * Hack TSEC 3 and 4 IO voltages. + */ + out_be32(&gur->tsec34ioovcr, 0xe7e0); /* 1110 0111 1110 0xxx */ + + out_be32(&ecm->eedr, 0xffffffff); /* clear ecm errors */ + out_be32(&ecm->eeer, 0xffffffff); /* enable ecm errors */ + return 0; +} + +phys_size_t fixed_sdram(void) +{ + ccsr_ddr_t *ddr = (void *)(CONFIG_SYS_MPC85xx_DDR_ADDR); + const char *p_mode = getenv("perf_mode"); + + puts("Initializing...."); + + out_be32(&ddr->cs0_bnds, CONFIG_SYS_DDR_CS0_BNDS); + out_be32(&ddr->cs0_config, CONFIG_SYS_DDR_CS0_CONFIG); + + out_be32(&ddr->timing_cfg_3, CONFIG_SYS_DDR_TIMING_3); + out_be32(&ddr->timing_cfg_0, CONFIG_SYS_DDR_TIMING_0); + + if (p_mode && !strcmp("performance", p_mode)) { + out_be32(&ddr->timing_cfg_1, CONFIG_SYS_DDR_TIMING_1_PERF); + out_be32(&ddr->timing_cfg_2, CONFIG_SYS_DDR_TIMING_2_PERF); + out_be32(&ddr->sdram_mode, CONFIG_SYS_DDR_MODE_1_PERF); + out_be32(&ddr->sdram_mode_2, CONFIG_SYS_DDR_MODE_2_PERF); + out_be32(&ddr->sdram_interval, CONFIG_SYS_DDR_INTERVAL_PERF); + } else { + out_be32(&ddr->timing_cfg_1, CONFIG_SYS_DDR_TIMING_1); + out_be32(&ddr->timing_cfg_2, CONFIG_SYS_DDR_TIMING_2); + out_be32(&ddr->sdram_mode, CONFIG_SYS_DDR_MODE_1); + out_be32(&ddr->sdram_mode_2, CONFIG_SYS_DDR_MODE_2); + out_be32(&ddr->sdram_interval, CONFIG_SYS_DDR_INTERVAL); + } + + out_be32(&ddr->sdram_clk_cntl, CONFIG_SYS_DDR_CLK_CTRL); + out_be32(&ddr->sdram_cfg_2, CONFIG_SYS_DDR_CONTROL2); + + asm("sync;isync"); + udelay(500); + + out_be32(&ddr->sdram_cfg, CONFIG_SYS_DDR_CONTROL); + asm("sync; isync"); + udelay(500); + + return ((phys_size_t)1) << CONFIG_SYS_SDRAM_SIZE_LOG; +} + +void pci_init_board(void) +{ + ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + + /* PCI is disabled */ + out_be32(&gur->devdisr, in_be32(&gur->devdisr) + | MPC85xx_DEVDISR_PCI1 + | MPC85xx_DEVDISR_PCI2 + | MPC85xx_DEVDISR_PCIE); +} + + +#if defined(CONFIG_OF_BOARD_SETUP) + +void ft_board_setup(void *blob, bd_t *bd) +{ + ft_cpu_setup(blob, bd); +} + +#endif diff --git a/board/mercury/mpq101/tlb.c b/board/mercury/mpq101/tlb.c new file mode 100644 index 0000000000..fd2eaec484 --- /dev/null +++ b/board/mercury/mpq101/tlb.c @@ -0,0 +1,82 @@ +/* + * (C) Copyright 2000 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include + +struct fsl_e_tlb_entry tlb_table[] = { + /* TLB 0 - for temp stack in cache */ + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, CONFIG_SYS_INIT_RAM_ADDR, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024, + CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024, + CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024, + CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + + /* + * TLB 0: 256M Non-cacheable, guarded + * 0xf0000000 256M LBC (FLASH included) + * Out of reset this entry is only 4K. + */ + SET_TLB_ENTRY(1, CONFIG_SYS_LBC_OPTION_BASE, + CONFIG_SYS_LBC_OPTION_BASE_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 0, BOOKE_PAGESZ_256M, 1), + + /* + * TLB 1: 1M Non-cacheable, guarded + * 0xe000_0000 1M CCSRBAR + */ + SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 1, BOOKE_PAGESZ_1M, 1), + +#ifdef CONFIG_SYS_SRIO1_MEM_PHYS + /* + * TLB 2: 256M Non-cacheable, guarded + */ + SET_TLB_ENTRY(1, CONFIG_SYS_SRIO1_MEM_VIRT, CONFIG_SYS_SRIO1_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 2, BOOKE_PAGESZ_256M, 1), + + /* + * TLB 3: 256M Non-cacheable, guarded + */ + SET_TLB_ENTRY(1, CONFIG_SYS_SRIO1_MEM_VIRT + 0x10000000, + CONFIG_SYS_SRIO1_MEM_PHYS + 0x10000000, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 3, BOOKE_PAGESZ_256M, 1), + +#endif +}; + +int num_tlb_entries = ARRAY_SIZE(tlb_table); diff --git a/board/mercury/mpq101/u-boot.lds b/board/mercury/mpq101/u-boot.lds new file mode 100644 index 0000000000..4f4dda57b9 --- /dev/null +++ b/board/mercury/mpq101/u-boot.lds @@ -0,0 +1,132 @@ +/* + * Copyright 2007-2009 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef RESET_VECTOR_ADDRESS +#define RESET_VECTOR_ADDRESS 0xfffffffc +#endif + +#include + +OUTPUT_ARCH(powerpc) + +PHDRS +{ + text PT_LOAD; + bss PT_LOAD; +} + +SECTIONS +{ + /* Read-only sections, merged into text segment: */ + . = + SIZEOF_HEADERS; + .interp : { *(.interp) } + /* To simplify mass deployment, environment precedes the monitor text in the + * same flash sector. + */ + .ppcenv CONFIG_ENV_ADDR : { common/env_embedded.o (.ppcenv) } + .text : + { + *(.text*) + } :text + _etext = .; + PROVIDE (etext = .); + .rodata : + { + *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*))) + } :text + + /* Read-write section, merged into data segment: */ + . = (. + 0x00FF) & 0xFFFFFF00; + _erotext = .; + PROVIDE (erotext = .); + .reloc : + { + _GOT2_TABLE_ = .; + KEEP(*(.got2)) + KEEP(*(.got)) + PROVIDE(_GLOBAL_OFFSET_TABLE_ = . + 4); + _FIXUP_TABLE_ = .; + KEEP(*(.fixup)) + } + __got2_entries = ((_GLOBAL_OFFSET_TABLE_ - _GOT2_TABLE_) >> 2) - 1; + __fixup_entries = (. - _FIXUP_TABLE_) >> 2; + + .data : + { + *(.data*) + *(.sdata*) + } + _edata = .; + PROVIDE (edata = .); + + . = .; + __u_boot_cmd_start = .; + .u_boot_cmd : { *(.u_boot_cmd) } + __u_boot_cmd_end = .; + + . = .; + __start___ex_table = .; + __ex_table : { *(__ex_table) } + __stop___ex_table = .; + + . = ALIGN(256); + __init_begin = .; + .text.init : { *(.text.init) } + .data.init : { *(.data.init) } + . = ALIGN(256); + __init_end = .; + + .bootpg RESET_VECTOR_ADDRESS - 0xffc : + { + arch/powerpc/cpu/mpc85xx/start.o (.bootpg) + } :text = 0xffff + + .resetvec RESET_VECTOR_ADDRESS : + { + KEEP(*(.resetvec)) + } :text = 0xffff + + . = RESET_VECTOR_ADDRESS + 0x4; + + /* + * Make sure that the bss segment isn't linked at 0x0, otherwise its + * address won't be updated during relocation fixups. Note that + * this is a temporary fix. Code to dynamically the fixup the bss + * location will be added in the future. When the bss relocation + * fixup code is present this workaround should be removed. + */ +#if (RESET_VECTOR_ADDRESS == 0xfffffffc) + . |= 0x10; +#endif + + __bss_start = .; + .bss (NOLOAD) : + { + *(.sbss*) + *(.bss*) + *(COMMON) + } :bss + + . = ALIGN(4); + _end = . ; + PROVIDE (end = .); +} diff --git a/boards.cfg b/boards.cfg index eceacf6763..141b143731 100644 --- a/boards.cfg +++ b/boards.cfg @@ -496,6 +496,7 @@ P2020RDB_NAND powerpc mpc85xx p1_p2_rdb freesca P2020RDB_SDCARD powerpc mpc85xx p1_p2_rdb freescale - P1_P2_RDB:P2020,SDCARD P2020RDB_SPIFLASH powerpc mpc85xx p1_p2_rdb freescale - P1_P2_RDB:P2020,SPIFLASH P4080DS powerpc mpc85xx corenet_ds freescale +mpq101 powerpc mpc85xx mpq101 mercury - mpq101 stxgp3 powerpc mpc85xx stxgp3 stx stxssa powerpc mpc85xx stxssa stx - stxssa stxssa_4M powerpc mpc85xx stxssa stx - stxssa:STXSSA_4M diff --git a/include/configs/mpq101.h b/include/configs/mpq101.h new file mode 100644 index 0000000000..e76ca73d47 --- /dev/null +++ b/include/configs/mpq101.h @@ -0,0 +1,394 @@ +/* + * Copyright 2011 Alex Dubov + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * Merury Computers MPQ101 board configuration file + * + */ +#ifndef __CONFIG_H +#define __CONFIG_H + +#ifdef CONFIG_36BIT +# define CONFIG_PHYS_64BIT +#endif + +/* High Level Configuration Options */ +#define CONFIG_BOOKE /* BOOKE */ +#define CONFIG_E500 /* BOOKE e500 family */ +#define CONFIG_MPC85xx /* MPC8540/60/55/41/48 */ +#define CONFIG_MPC8548 /* MPC8548 specific */ +#define CONFIG_MPQ101 /* MPQ101 board specific */ + +#define CONFIG_SYS_SRIO /* enable serial RapidIO */ +#define CONFIG_TSEC_ENET /* tsec ethernet support */ +#define CONFIG_INTERRUPTS /* enable pci, srio, ddr interrupts */ +#define CONFIG_FSL_LAW /* Use common FSL init code */ + +/* + * These can be toggled for performance analysis, otherwise use default. + */ +#define CONFIG_L2_CACHE /* toggle L2 cache */ +#define CONFIG_BTB /* toggle branch predition */ + +#define CONFIG_PANIC_HANG + +/* + * Only possible on E500 Version 2 or newer cores. + */ +#define CONFIG_ENABLE_36BIT_PHYS + +#ifdef CONFIG_PHYS_64BIT +# define CONFIG_ADDR_MAP +# define CONFIG_SYS_NUM_ADDR_MAP 16 /* number of TLB1 entries */ +#endif + + +#define CONFIG_SYS_CLK_FREQ 33000000 /* sysclk for MPC85xx */ + +/* + * Base addresses -- Note these are effective addresses where the + * actual resources get mapped (not physical addresses) + */ +#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 +#define CONFIG_SYS_CCSRBAR 0xe0000000 + +#ifdef CONFIG_PHYS_64BIT +# define CONFIG_SYS_CCSRBAR_PHYS 0xfe0000000ull +#else +# define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR +#endif + +#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR + +/* DDR Setup */ +#define CONFIG_FSL_DDR2 + +#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */ + +#define CONFIG_MEM_INIT_VALUE 0xDeadBeef +#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE + +#define CONFIG_NUM_DDR_CONTROLLERS 1 +#define CONFIG_DIMM_SLOTS_PER_CTLR 1 +#define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR) + +/* Fixed 512MB DDR2 parameters */ +#define CONFIG_SYS_SDRAM_SIZE_LOG 29 /* DDR is 512MB */ +#define CONFIG_SYS_DDR_CS0_BNDS 0x0000001f +#define CONFIG_SYS_DDR_CS0_CONFIG 0x80014102 +#define CONFIG_SYS_DDR_TIMING_3 0x00010000 +#define CONFIG_SYS_DDR_TIMING_0 0x00260802 +#define CONFIG_SYS_DDR_TIMING_1 0x5c47a432 +#define CONFIG_SYS_DDR_TIMING_1_PERF 0x49352322 +#define CONFIG_SYS_DDR_TIMING_2 0x03984cce +#define CONFIG_SYS_DDR_TIMING_2_PERF 0x14904cca +#define CONFIG_SYS_DDR_MODE_1 0x00400442 +#define CONFIG_SYS_DDR_MODE_1_PERF 0x00480432 +#define CONFIG_SYS_DDR_MODE_2 0x00000000 +#define CONFIG_SYS_DDR_MODE_2_PERF 0x00000000 +#define CONFIG_SYS_DDR_INTERVAL 0x08200100 +#define CONFIG_SYS_DDR_INTERVAL_PERF 0x06180100 +#define CONFIG_SYS_DDR_CLK_CTRL 0x03800000 +#define CONFIG_SYS_DDR_CONTROL 0xc3008000 /* Type = DDR2 */ +#define CONFIG_SYS_DDR_CONTROL2 0x04400000 + +#define CONFIG_SYS_ALT_MEMTEST +#define CONFIG_SYS_MEMTEST_START 0x0ff00000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x0ffffffc + +/* + * RAM definitions + */ +#define CONFIG_SYS_INIT_RAM_LOCK +#define CONFIG_SYS_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */ +#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in RAM */ + +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE \ + - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ +#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */ + +/* + * Local Bus Definitions + */ +#define CONFIG_SYS_LBC_LCRR 0x00000004 /* LB clock ratio reg */ +#define CONFIG_SYS_LBC_LBCR 0x00000000 /* LB config reg */ + + +/* + * FLASH on the Local Bus + * One bank, 128M, using the CFI driver. + */ +#define CONFIG_SYS_BOOT_BLOCK 0xf8000000 /* boot TLB block */ +#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_BOOT_BLOCK /* start of FLASH 128M */ + +#ifdef CONFIG_PHYS_64BIT +# define CONFIG_SYS_FLASH_BASE_PHYS 0xff8000000ull +#else +# define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE +#endif + +/* 0xf8001801 */ +#define CONFIG_SYS_BR0_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \ + | BR_PS_32 | BR_V) + +/* 0xf8006ff7 */ +#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(128) | OR_GPCM_XAM | OR_GPCM_CSNT \ + | OR_GPCM_ACS_DIV2 | OR_GPCM_XACS \ + | OR_GPCM_SCY_15 | OR_GPCM_TRLX \ + | OR_GPCM_EHTR | OR_GPCM_EAD) + +#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS} +#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ + +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 512 /* sectors per device */ + +#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ + +#define CONFIG_FLASH_CFI_DRIVER +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_SYS_FLASH_EMPTY_INFO +#define CONFIG_SYS_FLASH_AMD_CHECK_DQ7 +/* + * When initializing flash, if we cannot find the manufacturer ID, + * assume this is the AMD flash. + */ +#define CONFIG_ASSUME_AMD_FLASH + +/* + * Environment parameters + */ +#define CONFIG_ENV_IS_IN_FLASH +#define CONFIG_ENV_OVERWRITE +#define CONFIG_SYS_USE_PPCENV +#define ENV_IS_EMBEDDED +#define CONFIG_ENV_SECT_SIZE 0x40000 /* 256K */ +#define CONFIG_ENV_SIZE 0x800 + +/* Environment at the start of flash sector, before text. */ +#define CONFIG_ENV_ADDR (CONFIG_SYS_TEXT_BASE - CONFIG_ENV_SIZE) +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ +#define CONFIG_SYS_TEXT_BASE 0xfffc0800 +#define CONFIG_SYS_LDSCRIPT "board/mercury/mpq101/u-boot.lds" + +/* + * Cypress CY7C67200 USB controller on the Local Bus. + * Not supported by u-boot at present. + */ +#define CONFIG_SYS_LBC_OPTION_BASE 0xf0000000 + +#ifdef CONFIG_PHYS_64BIT +# define CONFIG_SYS_LBC_OPTION_BASE_PHYS 0xff0000000ull +#else +# define CONFIG_SYS_LBC_OPTION_BASE_PHYS CONFIG_SYS_LBC_OPTION_BASE +#endif + +/* 0xf0001001 */ +#define CONFIG_SYS_BR1_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_LBC_OPTION_BASE_PHYS) \ + | BR_PS_16 | BR_V) + +/* fffff002 */ +#define CONFIG_SYS_OR1_PRELIM (P2SZ_TO_AM(0x8000) | OR_GPCM_XAM \ + | OR_GPCM_BCTLD | OR_GPCM_EHTR) + +/* + * Serial Ports + */ +#define CONFIG_CONS_INDEX 2 +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) + +#define CONFIG_SYS_BAUDRATE_TABLE {300, 600, 1200, 2400, 4800, 9600, \ + 19200, 38400, 115200} + +#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) +#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) + +/* + * I2C buses and peripherals + */ +#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ +#define CONFIG_HARD_I2C /* I2C with hardware support*/ +#define CONFIG_I2C_MULTI_BUS +#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_SLAVE 0x7f +#define CONFIG_SYS_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C2_OFFSET 0x3100 + +/* I2C RTC - M41T81 */ +#define CONFIG_RTC_M41T62 +#define CONFIG_SYS_I2C_RTC_ADDR 0x68 +#define CONFIG_SYS_M41T11_BASE_YEAR 2000 + +/* I2C EEPROM - 24C256 */ +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 12 +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 +#define CONFIG_SYS_EEPROM_BUS_NUM 1 + +/* + * RapidIO MMU + */ +#ifdef CONFIG_SYS_SRIO +# define CONFIG_SRIO1 +# define CONFIG_SYS_SRIO1_MEM_VIRT 0xc0000000 +# define CONFIG_SYS_SRIO1_MEM_SIZE 0x20000000 /* 512M */ + +# ifdef CONFIG_PHYS_64BIT +# define CONFIG_SYS_SRIO1_MEM_PHYS 0xfc0000000ull +# else +# define CONFIG_SYS_SRIO1_MEM_PHYS CONFIG_SYS_SRIO1_MEM_VIRT +# endif +#endif + +/* + * Ethernet + */ +#ifdef CONFIG_TSEC_ENET + +# ifndef CONFIG_NET_MULTI +# define CONFIG_NET_MULTI +# endif + +# define CONFIG_MII /* MII PHY management */ +# define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */ + +# define CONFIG_TSEC1 +# define CONFIG_TSEC1_NAME "eTSEC0" +# define TSEC1_PHY_ADDR 0x10 +# define TSEC1_PHYIDX 0 +# define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) + +# define CONFIG_TSEC2 +# define CONFIG_TSEC2_NAME "eTSEC1" +# define TSEC2_PHY_ADDR 0x11 +# define TSEC2_PHYIDX 0 +# define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) + +# define CONFIG_TSEC3 +# define CONFIG_TSEC3_NAME "eTSEC2" +# define TSEC3_PHY_ADDR 0x12 +# define TSEC3_PHYIDX 0 +# define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) + +# define CONFIG_TSEC4 +# define CONFIG_TSEC4_NAME "eTSEC3" +# define TSEC4_PHY_ADDR 0x13 +# define TSEC4_PHYIDX 0 +# define TSEC4_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) + +/* Options are: eTSEC[0-3] */ +# define CONFIG_ETHPRIME "eTSEC0" +# define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */ +#endif + +/* + * Command line configuration. + */ +#include + +#define CONFIG_CMD_DATE +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_PING +#define CONFIG_CMD_SNTP +#define CONFIG_CMD_I2C +#define CONFIG_CMD_EEPROM +#define CONFIG_CMD_MII +#define CONFIG_CMD_ELF +#define CONFIG_CMD_IRQ +#define CONFIG_CMD_SETEXPR +#define CONFIG_CMD_JFFS2 + +/* + * Miscellaneous configurable options + */ + +/* pass open firmware flat tree */ +#define CONFIG_OF_LIBFDT +#define CONFIG_OF_BOARD_SETUP +#define CONFIG_OF_STDOUT_VIA_ALIAS + +#define CONFIG_FIT /* new uImage format support */ +#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */ + +/* Use the HUSH parser */ +#define CONFIG_SYS_HUSH_PARSER + +#ifdef CONFIG_SYS_HUSH_PARSER +# define CONFIG_SYS_PROMPT_HUSH_PS2 "> " +#endif + +#define CONFIG_LOADS_ECHO /* echo on for serial download */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ + +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_CMDLINE_EDITING /* Command-line editing */ +#define CONFIG_AUTO_COMPLETE /* add autocompletion support */ + +#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ +#define CONFIG_SYS_PROMPT "MPQ-101=> " /* Monitor Command Prompt */ + +/* Console I/O Buffer Size */ +#ifdef CONFIG_CMD_KGDB +# define CONFIG_SYS_CBSIZE 1024 +#else +# define CONFIG_SYS_CBSIZE 256 +#endif + +/* Print Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT)+16) + +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 16 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/ +#define CONFIG_SYS_BOOTM_LEN (16 << 20) /* Increase max gunzip size */ + +#ifdef CONFIG_CMD_KGDB +# define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ +# define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif + +/* + * Basic Environment Configuration + */ +#define CONFIG_BAUDRATE 115200 +#define CONFIG_BOOTDELAY 5 /* -1 disables auto-boot */ + +/*default location for tftp and bootm*/ +#define CONFIG_LOADADDR CONFIG_SYS_LOAD_ADDR + +#endif /* __CONFIG_H */ -- cgit