From 82a821f89bee913d7ba17cb500c778cf08dce321 Mon Sep 17 00:00:00 2001 From: Ajay Kumar Gupta Date: Tue, 22 Dec 2009 10:56:11 +0530 Subject: DA830: Add pinmux for USB0_DRVVBUS USB0_DRVVBUS pinmux configuration is required for USB functinality in uboot. Signed-off-by: Ajay Kumar Gupta Signed-off-by: Swaminathan S --- board/davinci/da830evm/da830evm.c | 8 ++++++++ 1 file changed, 8 insertions(+) diff --git a/board/davinci/da830evm/da830evm.c b/board/davinci/da830evm/da830evm.c index bb8cc3c928..7cf601301b 100644 --- a/board/davinci/da830evm/da830evm.c +++ b/board/davinci/da830evm/da830evm.c @@ -65,6 +65,11 @@ const struct pinmux_config i2c_pins[] = { { pinmux[9], 2, 4 } }; +/* USB0_DRVVBUS pin muxer settings */ +const struct pinmux_config usb_pins[] = { + { pinmux[9], 1, 1 } +}; + int board_init(void) { #ifndef CONFIG_USE_IRQ @@ -118,6 +123,9 @@ int board_init(void) if (davinci_configure_pin_mux(i2c_pins, ARRAY_SIZE(i2c_pins)) != 0) return 1; + if (davinci_configure_pin_mux(usb_pins, ARRAY_SIZE(usb_pins)) != 0) + return 1; + /* enable the console UART */ writel((DAVINCI_UART_PWREMU_MGMT_FREE | DAVINCI_UART_PWREMU_MGMT_URRST | DAVINCI_UART_PWREMU_MGMT_UTRST), -- cgit From 0b232310b2087d4278fb224fa01e228136fb8bdf Mon Sep 17 00:00:00 2001 From: Ajay Kumar Gupta Date: Tue, 22 Dec 2009 10:56:12 +0530 Subject: DA8xx: Add GPIO register definitions Added DA8xx GPIO base addresses in gpio_defs.h and pointers to different BANKs which can be used to program GPIOs. Signed-off-by: Ajay Kumar Gupta Signed-off-by: Swaminathan S --- include/asm-arm/arch-davinci/gpio_defs.h | 14 ++++++++++++++ 1 file changed, 14 insertions(+) diff --git a/include/asm-arm/arch-davinci/gpio_defs.h b/include/asm-arm/arch-davinci/gpio_defs.h index ff629761b5..1be2ac2660 100644 --- a/include/asm-arm/arch-davinci/gpio_defs.h +++ b/include/asm-arm/arch-davinci/gpio_defs.h @@ -22,12 +22,21 @@ #ifndef _GPIO_DEFS_H_ #define _GPIO_DEFS_H_ +#ifndef CONFIG_SOC_DA8XX #define DAVINCI_GPIO_BINTEN 0x01C67008 #define DAVINCI_GPIO_BANK01 0x01C67010 #define DAVINCI_GPIO_BANK23 0x01C67038 #define DAVINCI_GPIO_BANK45 0x01C67060 #define DAVINCI_GPIO_BANK67 0x01C67088 +#else /* CONFIG_SOC_DA8XX */ +#define DAVINCI_GPIO_BINTEN 0x01E26008 +#define DAVINCI_GPIO_BANK01 0x01E26010 +#define DAVINCI_GPIO_BANK23 0x01E26038 +#define DAVINCI_GPIO_BANK45 0x01E26060 +#define DAVINCI_GPIO_BANK67 0x01E26088 +#endif /* CONFIG_SOC_DA8XX */ + struct davinci_gpio { unsigned int dir; unsigned int out_data; @@ -49,4 +58,9 @@ struct davinci_gpio_bank { unsigned long base; }; +#define davinci_gpio_bank01 ((struct davinci_gpio *)DAVINCI_GPIO_BANK01) +#define davinci_gpio_bank23 ((struct davinci_gpio *)DAVINCI_GPIO_BANK23) +#define davinci_gpio_bank45 ((struct davinci_gpio *)DAVINCI_GPIO_BANK45) +#define davinci_gpio_bank67 ((struct davinci_gpio *)DAVINCI_GPIO_BANK67) + #endif -- cgit From 7359273d946a7dcde04c5e8d5bad669146efc87c Mon Sep 17 00:00:00 2001 From: Ajay Kumar Gupta Date: Tue, 22 Dec 2009 10:56:13 +0530 Subject: DA8xx: Add MUSB host support Tested USB host functionality on DA830 EVM. Signed-off-by: Ajay Kumar Gupta Signed-off-by: Swaminathan S --- drivers/usb/musb/Makefile | 1 + drivers/usb/musb/da8xx.c | 139 ++++++++++++++++++++++++++++++++++++++++++++++ drivers/usb/musb/da8xx.h | 103 ++++++++++++++++++++++++++++++++++ include/usb.h | 2 +- 4 files changed, 244 insertions(+), 1 deletion(-) create mode 100644 drivers/usb/musb/da8xx.c create mode 100644 drivers/usb/musb/da8xx.h diff --git a/drivers/usb/musb/Makefile b/drivers/usb/musb/Makefile index f2ccd9fe06..12e115ef11 100644 --- a/drivers/usb/musb/Makefile +++ b/drivers/usb/musb/Makefile @@ -29,6 +29,7 @@ COBJS-$(CONFIG_MUSB_HCD) += musb_hcd.o musb_core.o COBJS-$(CONFIG_MUSB_UDC) += musb_udc.o musb_core.o COBJS-$(CONFIG_USB_DAVINCI) += davinci.o COBJS-$(CONFIG_USB_OMAP3) += omap3.o +COBJS-$(CONFIG_USB_DA8XX) += da8xx.o COBJS := $(COBJS-y) SRCS := $(COBJS:.o=.c) diff --git a/drivers/usb/musb/da8xx.c b/drivers/usb/musb/da8xx.c new file mode 100644 index 0000000000..40bfe440d8 --- /dev/null +++ b/drivers/usb/musb/da8xx.c @@ -0,0 +1,139 @@ +/* + * da8xx.c - TI's DA8xx platform specific usb wrapper functions. + * + * Author: Ajay Kumar Gupta + * + * Based on drivers/usb/musb/davinci.c + * + * Copyright (C) 2009 Texas Instruments Incorporated + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ +#include + +#include "da8xx.h" + +/* MUSB platform configuration */ +struct musb_config musb_cfg = { + (struct musb_regs *)DA8XX_USB_OTG_CORE_BASE, + DA8XX_USB_OTG_TIMEOUT, + 0 +}; + +/* + * This function enables VBUS by driving the GPIO Bank4 Pin 15 high. + */ +static void enable_vbus(void) +{ + u32 value; + + /* configure GPIO bank4 pin 15 in output direction */ + value = readl(&davinci_gpio_bank45->dir); + writel((value & (~DA8XX_USB_VBUS_GPIO)), &davinci_gpio_bank45->dir); + + /* set GPIO bank4 pin 15 high to drive VBUS */ + value = readl(&davinci_gpio_bank45->set_data); + writel((value | DA8XX_USB_VBUS_GPIO), &davinci_gpio_bank45->set_data); +} + +/* + * Enable the usb0 phy. This initialization procedure is explained in + * the DA8xx USB user guide document. + */ +static u8 phy_on(void) +{ + u32 timeout; + u32 cfgchip2; + + cfgchip2 = readl(&davinci_syscfg_regs->cfgchip2); + + cfgchip2 &= ~(CFGCHIP2_RESET | CFGCHIP2_PHYPWRDN | CFGCHIP2_OTGPWRDN | + CFGCHIP2_OTGMODE | CFGCHIP2_REFFREQ); + cfgchip2 |= CFGCHIP2_SESENDEN | CFGCHIP2_VBDTCTEN | CFGCHIP2_PHY_PLLON | + CFGCHIP2_REFFREQ_24MHZ; + + writel(cfgchip2, &davinci_syscfg_regs->cfgchip2); + + /* wait until the usb phy pll locks */ + timeout = musb_cfg.timeout; + while (timeout--) + if (readl(&davinci_syscfg_regs->cfgchip2) & CFGCHIP2_PHYCLKGD) + return 1; + + /* USB phy was not turned on */ + return 0; +} + +/* + * Disable the usb phy + */ +static void phy_off(void) +{ + u32 cfgchip2; + + /* + * Power down the on-chip PHY. + */ + cfgchip2 = readl(&davinci_syscfg_regs->cfgchip2); + cfgchip2 &= ~CFGCHIP2_PHY_PLLON; + cfgchip2 |= CFGCHIP2_PHYPWRDN | CFGCHIP2_OTGPWRDN; + writel(cfgchip2, &davinci_syscfg_regs->cfgchip2); +} + +/* + * This function performs DA8xx platform specific initialization for usb0. + */ +int musb_platform_init(void) +{ + u32 revision; + + /* enable psc for usb2.0 */ + lpsc_on(33); + + /* enable usb vbus */ + enable_vbus(); + + /* reset the controller */ + writel(0x1, &da8xx_usb_regs->control); + udelay(5000); + + /* start the on-chip usb phy and its pll */ + if (phy_on() == 0) + return -1; + + /* Returns zero if e.g. not clocked */ + revision = readl(&da8xx_usb_regs->revision); + if (revision == 0) + return -1; + + /* Disable all interrupts */ + writel((DA8XX_USB_USBINT_MASK | DA8XX_USB_TXINT_MASK | + DA8XX_USB_RXINT_MASK), &da8xx_usb_regs->intmsk_set); + return 0; +} + +/* + * This function performs DA8xx platform specific deinitialization for usb0. + */ +void musb_platform_deinit(void) +{ + /* Turn of the phy */ + phy_off(); + + /* flush any interrupts */ + writel((DA8XX_USB_USBINT_MASK | DA8XX_USB_TXINT_MASK | + DA8XX_USB_RXINT_MASK), &da8xx_usb_regs->intmsk_clr); + writel(0, &da8xx_usb_regs->eoi); +} diff --git a/drivers/usb/musb/da8xx.h b/drivers/usb/musb/da8xx.h new file mode 100644 index 0000000000..93234f0dd4 --- /dev/null +++ b/drivers/usb/musb/da8xx.h @@ -0,0 +1,103 @@ +/* + * da8xx.h -- TI's DA8xx platform specific usb wrapper definitions. + * + * Author: Ajay Kumar Gupta + * + * Based on drivers/usb/musb/davinci.h + * + * Copyright (C) 2009 Texas Instruments Incorporated + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ +#ifndef __DA8XX_MUSB_H__ +#define __DA8XX_MUSB_H__ + +#include +#include +#include "musb_core.h" + +/* Base address of da8xx usb0 wrapper */ +#define DA8XX_USB_OTG_BASE 0x01E00000 + +/* Base address of da8xx musb core */ +#define DA8XX_USB_OTG_CORE_BASE (DA8XX_USB_OTG_BASE + 0x400) + +/* Timeout for DA8xx usb module */ +#define DA8XX_USB_OTG_TIMEOUT 0x3FFFFFF + +/* + * DA8xx platform USB wrapper register overlay. + */ +struct da8xx_usb_regs { + dv_reg revision; + dv_reg control; + dv_reg status; + dv_reg emulation; + dv_reg mode; + dv_reg autoreq; + dv_reg srpfixtime; + dv_reg teardown; + dv_reg intsrc; + dv_reg intsrc_set; + dv_reg intsrc_clr; + dv_reg intmsk; + dv_reg intmsk_set; + dv_reg intmsk_clr; + dv_reg intsrcmsk; + dv_reg eoi; + dv_reg intvector; + dv_reg grndis_size[4]; +}; + +#define da8xx_usb_regs ((struct da8xx_usb_regs *)DA8XX_USB_OTG_BASE) + +/* DA8XX interrupt bits definitions */ +#define DA8XX_USB_TX_ENDPTS_MASK 0x1f /* ep0 + 4 tx */ +#define DA8XX_USB_RX_ENDPTS_MASK 0x1e /* 4 rx */ +#define DA8XX_USB_TXINT_SHIFT 0 +#define DA8XX_USB_RXINT_SHIFT 8 + +#define DA8XX_USB_USBINT_MASK 0x01ff0000 /* 8 Mentor, DRVVBUS */ +#define DA8XX_USB_TXINT_MASK \ + (DA8XX_USB_TX_ENDPTS_MASK << DA8XX_USB_TXINT_SHIFT) +#define DA8XX_USB_RXINT_MASK \ + (DA8XX_USB_RX_ENDPTS_MASK << DA8XX_USB_RXINT_SHIFT) + +/* DA8xx CFGCHIP2 (USB 2.0 PHY Control) register bits */ +#define CFGCHIP2_PHYCLKGD (1 << 17) +#define CFGCHIP2_VBUSSENSE (1 << 16) +#define CFGCHIP2_RESET (1 << 15) +#define CFGCHIP2_OTGMODE (3 << 13) +#define CFGCHIP2_NO_OVERRIDE (0 << 13) +#define CFGCHIP2_FORCE_HOST (1 << 13) +#define CFGCHIP2_FORCE_DEVICE (2 << 13) +#define CFGCHIP2_FORCE_HOST_VBUS_LOW (3 << 13) +#define CFGCHIP2_USB1PHYCLKMUX (1 << 12) +#define CFGCHIP2_USB2PHYCLKMUX (1 << 11) +#define CFGCHIP2_PHYPWRDN (1 << 10) +#define CFGCHIP2_OTGPWRDN (1 << 9) +#define CFGCHIP2_DATPOL (1 << 8) +#define CFGCHIP2_USB1SUSPENDM (1 << 7) +#define CFGCHIP2_PHY_PLLON (1 << 6) /* override PLL suspend */ +#define CFGCHIP2_SESENDEN (1 << 5) /* Vsess_end comparator */ +#define CFGCHIP2_VBDTCTEN (1 << 4) /* Vbus comparator */ +#define CFGCHIP2_REFFREQ (0xf << 0) +#define CFGCHIP2_REFFREQ_12MHZ (1 << 0) +#define CFGCHIP2_REFFREQ_24MHZ (2 << 0) +#define CFGCHIP2_REFFREQ_48MHZ (3 << 0) + +#define DA8XX_USB_VBUS_GPIO (1 << 15) +#endif /* __DA8XX_MUSB_H__ */ + diff --git a/include/usb.h b/include/usb.h index 1cc3e4229d..2a9cd04eb9 100644 --- a/include/usb.h +++ b/include/usb.h @@ -132,7 +132,7 @@ struct usb_device { defined(CONFIG_USB_EHCI) || defined(CONFIG_USB_OHCI_NEW) || \ defined(CONFIG_USB_SL811HS) || defined(CONFIG_USB_ISP116X_HCD) || \ defined(CONFIG_USB_R8A66597_HCD) || defined(CONFIG_USB_DAVINCI) || \ - defined(CONFIG_USB_OMAP3) + defined(CONFIG_USB_OMAP3) || defined(CONFIG_USB_DA8XX) int usb_lowlevel_init(void); int usb_lowlevel_stop(void); -- cgit From 7b4292883b6fdc42984671fbe4e0a352ec704bde Mon Sep 17 00:00:00 2001 From: Ajay Kumar Gupta Date: Tue, 22 Dec 2009 10:56:14 +0530 Subject: DA830: Add usb config Adding USB configuration. Default is set for USB MSC host. Signed-off-by: Ajay Kumar Gupta Signed-off-by: Swaminathan S --- include/configs/da830evm.h | 38 +++++++++++++++++++++++++++++++++----- 1 file changed, 33 insertions(+), 5 deletions(-) diff --git a/include/configs/da830evm.h b/include/configs/da830evm.h index 38e2ce1f1c..432cd57a70 100644 --- a/include/configs/da830evm.h +++ b/include/configs/da830evm.h @@ -149,6 +149,11 @@ #define CONFIG_SYS_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED #endif +/* + * USB configuration + */ +#define CONFIG_USB_DA8XX /* Platform hookup to MUSB controller */ +#define CONFIG_MUSB_HCD /* * U-Boot general configuration @@ -234,10 +239,33 @@ #endif #ifdef CONFIG_USB_DA8XX -#define CONFIG_CMD_USB /* include support for usb */ -#define CONFIG_CMD_STORAGE /* include support for usb */ -#define CONFIG_CMD_FAT /* include support for FAT/storage*/ -#define CONFIG_DOS_PARTITION /* include support for FAT/storage*/ -#endif +#ifdef CONFIG_MUSB_HCD /* include support for usb host */ +#define CONFIG_CMD_USB /* include support for usb cmd */ + +#define CONFIG_USB_STORAGE /* MSC class support */ +#define CONFIG_CMD_STORAGE /* inclue support for usb-storage cmd */ +#define CONFIG_CMD_FAT /* inclue support for FAT/storage */ +#define CONFIG_DOS_PARTITION /* inclue support for FAT/storage */ + +#ifdef CONFIG_USB_KEYBOARD /* HID class support */ +#define CONFIG_SYS_USB_EVENT_POLL +#define CONFIG_PREBOOT "usb start" +#endif /* CONFIG_USB_KEYBOARD */ + +#endif /* CONFIG_MUSB_HCD */ + +#ifdef CONFIG_MUSB_UDC +/* USB device configuration */ +#define CONFIG_USB_DEVICE 1 +#define CONFIG_USB_TTY 1 +#define CONFIG_SYS_CONSOLE_IS_IN_ENV 1 +/* Change these to suit your needs */ +#define CONFIG_USBD_VENDORID 0x0451 +#define CONFIG_USBD_PRODUCTID 0x5678 +#define CONFIG_USBD_MANUFACTURER "Texas Instruments" +#define CONFIG_USBD_PRODUCT_NAME "DA830EVM" +#endif /* CONFIG_MUSB_UDC */ + +#endif /* CONFIG_USB_DA8XX */ #endif /* __CONFIG_H */ -- cgit From dc2cd05c91a134d53fada41e8f97a434be22de02 Mon Sep 17 00:00:00 2001 From: Mike Frysinger Date: Wed, 16 Dec 2009 22:03:58 -0500 Subject: usb: musb: make sure the register layout is packed Signed-off-by: Mike Frysinger Signed-off-by: Remy Bohmer --- drivers/usb/musb/musb_core.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/usb/musb/musb_core.h b/drivers/usb/musb/musb_core.h index 15c7f49a35..cee7a11294 100644 --- a/drivers/usb/musb/musb_core.h +++ b/drivers/usb/musb/musb_core.h @@ -137,7 +137,7 @@ struct musb_regs { struct musb_epN_regs epN; } ep[16]; -} __attribute__((aligned(32))); +} __attribute__((packed, aligned(32))); /* * MUSB Register bits -- cgit From df402ba38103df51f6929848b6a797eff4db61f8 Mon Sep 17 00:00:00 2001 From: Bryan Wu Date: Wed, 16 Dec 2009 22:03:59 -0500 Subject: usb: musb: make fifo support configurable The dynamic FIFO handling under MUSB is optional, and some parts (like the Blackfin processor) do not implement support for it. Due to this, the FIFO reading/writing steps need special handling, so mark the common versions weak so drivers can override. Signed-off-by: Bryan Wu Signed-off-by: Cliff Cai Signed-off-by: Mike Frysinger Signed-off-by: Remy Bohmer --- drivers/usb/musb/musb_core.c | 18 ++++++++++++++---- 1 file changed, 14 insertions(+), 4 deletions(-) diff --git a/drivers/usb/musb/musb_core.c b/drivers/usb/musb/musb_core.c index 22f3dba0cf..7766069bfc 100644 --- a/drivers/usb/musb/musb_core.c +++ b/drivers/usb/musb/musb_core.c @@ -50,6 +50,16 @@ void musb_start(void) #endif } +#ifdef MUSB_NO_DYNAMIC_FIFO +# define config_fifo(dir, idx, addr) +#else +# define config_fifo(dir, idx, addr) \ + do { \ + writeb(idx, &musbr->dir##fifosz); \ + writew(fifoaddr >> 3, &musbr->dir##fifoadd); \ + } while (0) +#endif + /* * This function configures the endpoint configuration. The musb hcd or musb * device implementation can use this function to configure the endpoints @@ -74,8 +84,7 @@ void musb_configure_ep(struct musb_epinfo *epinfo, u8 cnt) writeb(epinfo->epnum, &musbr->index); if (epinfo->epdir) { /* Configure fifo size and fifo base address */ - writeb(idx, &musbr->txfifosz); - writew(fifoaddr >> 3, &musbr->txfifoadd); + config_fifo(tx, idx, fifoaddr); csr = readw(&musbr->txcsr); #if defined(CONFIG_MUSB_HCD) @@ -88,8 +97,7 @@ void musb_configure_ep(struct musb_epinfo *epinfo, u8 cnt) &musbr->txcsr); } else { /* Configure fifo size and fifo base address */ - writeb(idx, &musbr->rxfifosz); - writew(fifoaddr >> 3, &musbr->rxfifoadd); + config_fifo(rx, idx, fifoaddr); csr = readw(&musbr->rxcsr); #if defined(CONFIG_MUSB_HCD) @@ -113,6 +121,7 @@ void musb_configure_ep(struct musb_epinfo *epinfo, u8 cnt) * length - number of bytes to write to FIFO * fifo_data - Pointer to data buffer that contains the data to write */ +__attribute__((weak)) void write_fifo(u8 ep, u32 length, void *fifo_data) { u8 *data = (u8 *)fifo_data; @@ -132,6 +141,7 @@ void write_fifo(u8 ep, u32 length, void *fifo_data) * length - number of bytes to read from FIFO * fifo_data - pointer to data buffer into which data is read */ +__attribute__((weak)) void read_fifo(u8 ep, u32 length, void *fifo_data) { u8 *data = (u8 *)fifo_data; -- cgit From 8868fd443b7a52bf433903cc9527403ad055acb9 Mon Sep 17 00:00:00 2001 From: Bryan Wu Date: Wed, 16 Dec 2009 22:04:00 -0500 Subject: usb: musb: make multipoint optional The multipoint handling under MUSB is optional, and some parts (like the Blackfin processor) do not implement support for it. Signed-off-by: Bryan Wu Signed-off-by: Cliff Cai Signed-off-by: Mike Frysinger Signed-off-by: Remy Bohmer --- drivers/usb/musb/musb_hcd.c | 20 ++++++++++++++++++++ 1 file changed, 20 insertions(+) diff --git a/drivers/usb/musb/musb_hcd.c b/drivers/usb/musb/musb_hcd.c index 555d2dc1b0..5481600509 100644 --- a/drivers/usb/musb/musb_hcd.c +++ b/drivers/usb/musb/musb_hcd.c @@ -402,11 +402,13 @@ static void config_hub_port(struct usb_device *dev, u8 ep) if (dev->parent->children[chid] == dev) break; +#ifndef MUSB_NO_MULTIPOINT /* configure the hub address and the port address */ writeb(hub, &musbr->tar[ep].txhubaddr); writeb((chid + 1), &musbr->tar[ep].txhubport); writeb(hub, &musbr->tar[ep].rxhubaddr); writeb((chid + 1), &musbr->tar[ep].rxhubport); +#endif } /* @@ -415,7 +417,9 @@ static void config_hub_port(struct usb_device *dev, u8 ep) int submit_control_msg(struct usb_device *dev, unsigned long pipe, void *buffer, int len, struct devrequest *setup) { +#ifndef MUSB_NO_MULTIPOINT int devnum = usb_pipedevice(pipe); +#endif u16 csr; u8 devspeed; @@ -423,9 +427,11 @@ int submit_control_msg(struct usb_device *dev, unsigned long pipe, void *buffer, writeb(MUSB_CONTROL_EP, &musbr->index); csr = readw(&musbr->txcsr); +#ifndef MUSB_NO_MULTIPOINT /* target addr and (for multipoint) hub addr/port */ writeb(devnum, &musbr->tar[MUSB_CONTROL_EP].txfuncaddr); writeb(devnum, &musbr->tar[MUSB_CONTROL_EP].rxfuncaddr); +#endif /* configure the hub address and the port number as required */ devspeed = get_dev_speed(dev); @@ -435,10 +441,12 @@ int submit_control_msg(struct usb_device *dev, unsigned long pipe, void *buffer, writeb(devspeed << 6, &musbr->txtype); } else { writeb(musb_cfg.musb_speed << 6, &musbr->txtype); +#ifndef MUSB_NO_MULTIPOINT writeb(0, &musbr->tar[MUSB_CONTROL_EP].txhubaddr); writeb(0, &musbr->tar[MUSB_CONTROL_EP].txhubport); writeb(0, &musbr->tar[MUSB_CONTROL_EP].rxhubaddr); writeb(0, &musbr->tar[MUSB_CONTROL_EP].rxhubport); +#endif } /* Control transfer setup phase */ @@ -497,7 +505,9 @@ int submit_bulk_msg(struct usb_device *dev, unsigned long pipe, { int dir_out = usb_pipeout(pipe); int ep = usb_pipeendpoint(pipe); +#ifndef MUSB_NO_MULTIPOINT int devnum = usb_pipedevice(pipe); +#endif u8 type; u16 csr; u32 txlen = 0; @@ -507,11 +517,13 @@ int submit_bulk_msg(struct usb_device *dev, unsigned long pipe, /* select bulk endpoint */ writeb(MUSB_BULK_EP, &musbr->index); +#ifndef MUSB_NO_MULTIPOINT /* write the address of the device */ if (dir_out) writeb(devnum, &musbr->tar[MUSB_BULK_EP].txfuncaddr); else writeb(devnum, &musbr->tar[MUSB_BULK_EP].rxfuncaddr); +#endif /* configure the hub address and the port number as required */ devspeed = get_dev_speed(dev); @@ -524,6 +536,7 @@ int submit_bulk_msg(struct usb_device *dev, unsigned long pipe, */ config_hub_port(dev, MUSB_BULK_EP); } else { +#ifndef MUSB_NO_MULTIPOINT if (dir_out) { writeb(0, &musbr->tar[MUSB_BULK_EP].txhubaddr); writeb(0, &musbr->tar[MUSB_BULK_EP].txhubport); @@ -531,6 +544,7 @@ int submit_bulk_msg(struct usb_device *dev, unsigned long pipe, writeb(0, &musbr->tar[MUSB_BULK_EP].rxhubaddr); writeb(0, &musbr->tar[MUSB_BULK_EP].rxhubport); } +#endif devspeed = musb_cfg.musb_speed; } @@ -696,7 +710,9 @@ int submit_int_msg(struct usb_device *dev, unsigned long pipe, { int dir_out = usb_pipeout(pipe); int ep = usb_pipeendpoint(pipe); +#ifndef MUSB_NO_MULTIPOINT int devnum = usb_pipedevice(pipe); +#endif u8 type; u16 csr; u32 txlen = 0; @@ -706,11 +722,13 @@ int submit_int_msg(struct usb_device *dev, unsigned long pipe, /* select interrupt endpoint */ writeb(MUSB_INTR_EP, &musbr->index); +#ifndef MUSB_NO_MULTIPOINT /* write the address of the device */ if (dir_out) writeb(devnum, &musbr->tar[MUSB_INTR_EP].txfuncaddr); else writeb(devnum, &musbr->tar[MUSB_INTR_EP].rxfuncaddr); +#endif /* configure the hub address and the port number as required */ devspeed = get_dev_speed(dev); @@ -723,6 +741,7 @@ int submit_int_msg(struct usb_device *dev, unsigned long pipe, */ config_hub_port(dev, MUSB_INTR_EP); } else { +#ifndef MUSB_NO_MULTIPOINT if (dir_out) { writeb(0, &musbr->tar[MUSB_INTR_EP].txhubaddr); writeb(0, &musbr->tar[MUSB_INTR_EP].txhubport); @@ -730,6 +749,7 @@ int submit_int_msg(struct usb_device *dev, unsigned long pipe, writeb(0, &musbr->tar[MUSB_INTR_EP].rxhubaddr); writeb(0, &musbr->tar[MUSB_INTR_EP].rxhubport); } +#endif devspeed = musb_cfg.musb_speed; } -- cgit From bc72a919e037782f64e3ac45c91bc60408e57e85 Mon Sep 17 00:00:00 2001 From: Bryan Wu Date: Wed, 16 Dec 2009 22:04:01 -0500 Subject: usb: musb: change rxcsr register from write to read/modify/write The RX Control/Status register has bits that we want to preserve, so don't just write out a single bit. Preserve the others bits in the process. The original code posted to the u-boot list had this behavior, but looks like it was lost somewhere along the way to merging. Signed-off-by: Bryan Wu Signed-off-by: Cliff Cai Signed-off-by: Mike Frysinger Signed-off-by: Remy Bohmer --- drivers/usb/musb/musb_hcd.c | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-) diff --git a/drivers/usb/musb/musb_hcd.c b/drivers/usb/musb/musb_hcd.c index 5481600509..adb8c38527 100644 --- a/drivers/usb/musb/musb_hcd.c +++ b/drivers/usb/musb/musb_hcd.c @@ -604,7 +604,8 @@ int submit_bulk_msg(struct usb_device *dev, unsigned long pipe, (len-txlen) : dev->epmaxpacketin[ep]; /* Set the ReqPkt bit */ - writew(MUSB_RXCSR_H_REQPKT, &musbr->rxcsr); + csr = readw(&musbr->rxcsr); + writew(csr | MUSB_RXCSR_H_REQPKT, &musbr->rxcsr); /* Wait until the RxPktRdy bit is set */ if (!wait_until_rxep_ready(dev, MUSB_BULK_EP)) { @@ -775,7 +776,8 @@ int submit_int_msg(struct usb_device *dev, unsigned long pipe, (len-txlen) : dev->epmaxpacketin[ep]; /* Set the ReqPkt bit */ - writew(MUSB_RXCSR_H_REQPKT, &musbr->rxcsr); + csr = readw(&musbr->rxcsr); + writew(csr | MUSB_RXCSR_H_REQPKT, &musbr->rxcsr); /* Wait until the RxPktRdy bit is set */ if (!wait_until_rxep_ready(dev, MUSB_INTR_EP)) { -- cgit From e608f221c13943d88e86f44753e23668342c3df3 Mon Sep 17 00:00:00 2001 From: Bryan Wu Date: Wed, 16 Dec 2009 22:04:02 -0500 Subject: usb: musb: add support for Blackfin MUSB Signed-off-by: Bryan Wu Signed-off-by: Cliff Cai Signed-off-by: Mike Frysinger Signed-off-by: Remy Bohmer --- drivers/usb/musb/Makefile | 1 + drivers/usb/musb/blackfin_usb.c | 143 +++++++++++++++ drivers/usb/musb/blackfin_usb.h | 99 +++++++++++ drivers/usb/musb/musb_core.h | 16 ++ drivers/usb/musb/musb_hcd.h | 4 +- include/asm-blackfin/mach-common/bits/usb.h | 264 ++++++++++++++++++++++++++++ include/usb.h | 3 +- 7 files changed, 528 insertions(+), 2 deletions(-) create mode 100644 drivers/usb/musb/blackfin_usb.c create mode 100644 drivers/usb/musb/blackfin_usb.h create mode 100644 include/asm-blackfin/mach-common/bits/usb.h diff --git a/drivers/usb/musb/Makefile b/drivers/usb/musb/Makefile index 12e115ef11..397f5fe7a3 100644 --- a/drivers/usb/musb/Makefile +++ b/drivers/usb/musb/Makefile @@ -27,6 +27,7 @@ LIB := $(obj)libusb_musb.a COBJS-$(CONFIG_MUSB_HCD) += musb_hcd.o musb_core.o COBJS-$(CONFIG_MUSB_UDC) += musb_udc.o musb_core.o +COBJS-$(CONFIG_USB_BLACKFIN) += blackfin_usb.o COBJS-$(CONFIG_USB_DAVINCI) += davinci.o COBJS-$(CONFIG_USB_OMAP3) += omap3.o COBJS-$(CONFIG_USB_DA8XX) += da8xx.o diff --git a/drivers/usb/musb/blackfin_usb.c b/drivers/usb/musb/blackfin_usb.c new file mode 100644 index 0000000000..38aceb2e93 --- /dev/null +++ b/drivers/usb/musb/blackfin_usb.c @@ -0,0 +1,143 @@ +/* + * Blackfin MUSB HCD (Host Controller Driver) for u-boot + * + * Copyright (c) 2008-2009 Analog Devices Inc. + * + * Licensed under the GPL-2 or later. + */ + +#include + +#include + +#include +#include + +#include "musb_core.h" + +/* MUSB platform configuration */ +struct musb_config musb_cfg = { + .regs = (struct musb_regs *)USB_FADDR, + .timeout = 0x3FFFFFF, + .musb_speed = 0, +}; + +/* + * This function read or write data to endpoint fifo + * Blackfin use DMA polling method to avoid buffer alignment issues + * + * ep - Endpoint number + * length - Number of bytes to write to FIFO + * fifo_data - Pointer to data buffer to be read/write + * is_write - Flag for read or write + */ +void rw_fifo(u8 ep, u32 length, void *fifo_data, int is_write) +{ + struct bfin_musb_dma_regs *regs; + u32 val = (u32)fifo_data; + + blackfin_dcache_flush_invalidate_range(fifo_data, fifo_data + length); + + regs = (void *)USB_DMA_INTERRUPT; + regs += ep; + + /* Setup DMA address register */ + bfin_write16(®s->addr_low, val); + SSYNC(); + + bfin_write16(®s->addr_high, val >> 16); + SSYNC(); + + /* Setup DMA count register */ + bfin_write16(®s->count_low, length); + bfin_write16(®s->count_high, 0); + SSYNC(); + + /* Enable the DMA */ + val = (ep << 4) | DMA_ENA | INT_ENA; + if (is_write) + val |= DIRECTION; + bfin_write16(®s->control, val); + SSYNC(); + + /* Wait for compelete */ + while (!(bfin_read_USB_DMA_INTERRUPT() & (1 << ep))) + continue; + + /* acknowledge dma interrupt */ + bfin_write_USB_DMA_INTERRUPT(1 << ep); + SSYNC(); + + /* Reset DMA */ + bfin_write16(®s->control, 0); + SSYNC(); +} + +void write_fifo(u8 ep, u32 length, void *fifo_data) +{ + rw_fifo(ep, length, fifo_data, 1); +} + +void read_fifo(u8 ep, u32 length, void *fifo_data) +{ + rw_fifo(ep, length, fifo_data, 0); +} + + +/* + * CPU and board-specific MUSB initializations. Aliased function + * signals caller to move on. + */ +static void __def_musb_init(void) +{ +} +void board_musb_init(void) __attribute__((weak, alias("__def_musb_init"))); + +int musb_platform_init(void) +{ + /* board specific initialization */ + board_musb_init(); + + if (ANOMALY_05000346) { + bfin_write_USB_APHY_CALIB(ANOMALY_05000346_value); + SSYNC(); + } + + if (ANOMALY_05000347) { + bfin_write_USB_APHY_CNTRL(0x0); + SSYNC(); + } + + /* Configure PLL oscillator register */ + bfin_write_USB_PLLOSC_CTRL(0x30a8); + SSYNC(); + + bfin_write_USB_SRP_CLKDIV((get_sclk()/1000) / 32 - 1); + SSYNC(); + + bfin_write_USB_EP_NI0_RXMAXP(64); + SSYNC(); + + bfin_write_USB_EP_NI0_TXMAXP(64); + SSYNC(); + + /* Route INTRUSB/INTR_RX/INTR_TX to USB_INT0*/ + bfin_write_USB_GLOBINTR(0x7); + SSYNC(); + + bfin_write_USB_GLOBAL_CTL(GLOBAL_ENA | EP1_TX_ENA | EP2_TX_ENA | + EP3_TX_ENA | EP4_TX_ENA | EP5_TX_ENA | + EP6_TX_ENA | EP7_TX_ENA | EP1_RX_ENA | + EP2_RX_ENA | EP3_RX_ENA | EP4_RX_ENA | + EP5_RX_ENA | EP6_RX_ENA | EP7_RX_ENA); + SSYNC(); + + return 0; +} + +/* + * This function performs Blackfin platform specific deinitialization for usb. +*/ +void musb_platform_deinit(void) +{ +} diff --git a/drivers/usb/musb/blackfin_usb.h b/drivers/usb/musb/blackfin_usb.h new file mode 100644 index 0000000000..ab26ca2d51 --- /dev/null +++ b/drivers/usb/musb/blackfin_usb.h @@ -0,0 +1,99 @@ +/* + * Blackfin MUSB HCD (Host Controller Driver) for u-boot + * + * Copyright (c) 2008-2009 Analog Devices Inc. + * + * Licensed under the GPL-2 or later. + */ + +#ifndef __BLACKFIN_USB_H__ +#define __BLACKFIN_USB_H__ + +#include + +/* Every register is 32bit aligned, but only 16bits in size */ +#define ureg(name) u16 name; u16 __pad_##name; + +#define musb_regs musb_regs +struct musb_regs { + /* common registers */ + ureg(faddr) + ureg(power) + ureg(intrtx) + ureg(intrrx) + ureg(intrtxe) + ureg(intrrxe) + ureg(intrusb) + ureg(intrusbe) + ureg(frame) + ureg(index) + ureg(testmode) + ureg(globintr) + ureg(global_ctl) + u32 reserved0[3]; + /* indexed registers */ + ureg(txmaxp) + ureg(txcsr) + ureg(rxmaxp) + ureg(rxcsr) + ureg(rxcount) + ureg(txtype) + ureg(txinterval) + ureg(rxtype) + ureg(rxinterval) + u32 reserved1; + ureg(txcount) + u32 reserved2[5]; + /* fifo */ + u16 fifox[32]; + /* OTG, dynamic FIFO, version & vendor registers */ + u32 reserved3[16]; + ureg(devctl) + ureg(vbus_irq) + ureg(vbus_mask) + u32 reserved4[15]; + ureg(linkinfo) + ureg(vplen) + ureg(hseof1) + ureg(fseof1) + ureg(lseof1) + u32 reserved5[41]; + /* target address registers */ + struct musb_tar_regs { + ureg(txmaxp) + ureg(txcsr) + ureg(rxmaxp) + ureg(rxcsr) + ureg(rxcount) + ureg(txtype) + ureg(txinternal) + ureg(rxtype) + ureg(rxinternal) + u32 reserved6; + ureg(txcount) + u32 reserved7[5]; + } tar[8]; +} __attribute__((packed)); + +struct bfin_musb_dma_regs { + ureg(interrupt); + ureg(control); + ureg(addr_low); + ureg(addr_high); + ureg(count_low); + ureg(count_high); + ureg(pad); +}; + +#undef ureg + +/* EP5-EP7 are the only ones with 1024 byte FIFOs which BULK really needs */ +#define MUSB_BULK_EP 5 + +/* Blackfin FIFO's are static */ +#define MUSB_NO_DYNAMIC_FIFO + +/* No HUB support :( */ +#define MUSB_NO_MULTIPOINT + +#endif diff --git a/drivers/usb/musb/musb_core.h b/drivers/usb/musb/musb_core.h index cee7a11294..f0f0301bd1 100644 --- a/drivers/usb/musb/musb_core.h +++ b/drivers/usb/musb/musb_core.h @@ -38,6 +38,10 @@ #include #include +#ifdef CONFIG_USB_BLACKFIN +# include "blackfin_usb.h" +#endif + #define MUSB_EP0_FIFOSIZE 64 /* This is non-configurable */ /* EP0 */ @@ -71,6 +75,7 @@ struct musb_epN_regs { }; /* Mentor USB core register overlay structure */ +#ifndef musb_regs struct musb_regs { /* common registers */ u8 faddr; @@ -138,6 +143,7 @@ struct musb_regs { } ep[16]; } __attribute__((packed, aligned(32))); +#endif /* * MUSB Register bits @@ -347,4 +353,14 @@ extern void musb_configure_ep(struct musb_epinfo *epinfo, u8 cnt); extern void write_fifo(u8 ep, u32 length, void *fifo_data); extern void read_fifo(u8 ep, u32 length, void *fifo_data); +#if defined(CONFIG_USB_BLACKFIN) +/* Every USB register is accessed as a 16-bit even if the value itself + * is only 8-bits in size. Fun stuff. + */ +# undef readb +# define readb(addr) (u8)bfin_read16(addr) +# undef writeb +# define writeb(b, addr) bfin_write16(addr, b) +#endif + #endif /* __MUSB_HDRC_DEFS_H__ */ diff --git a/drivers/usb/musb/musb_hcd.h b/drivers/usb/musb/musb_hcd.h index 17e9091a0a..a437985dc8 100644 --- a/drivers/usb/musb/musb_hcd.h +++ b/drivers/usb/musb/musb_hcd.h @@ -38,7 +38,9 @@ extern unsigned char new[]; #define MUSB_CONTROL_EP 0 /* This defines the endpoint number used for bulk transfer */ -#define MUSB_BULK_EP 1 +#ifndef MUSB_BULK_EP +# define MUSB_BULK_EP 1 +#endif /* This defines the endpoint number used for interrupt transfer */ #define MUSB_INTR_EP 2 diff --git a/include/asm-blackfin/mach-common/bits/usb.h b/include/asm-blackfin/mach-common/bits/usb.h new file mode 100644 index 0000000000..c6390589bc --- /dev/null +++ b/include/asm-blackfin/mach-common/bits/usb.h @@ -0,0 +1,264 @@ +/* + * USB Masks + */ + +#ifndef __BFIN_PERIPHERAL_USB__ +#define __BFIN_PERIPHERAL_USB__ + +/* Bit masks for USB_FADDR */ + +#define FUNCTION_ADDRESS 0x7f /* Function address */ + +/* Bit masks for USB_POWER */ + +#define ENABLE_SUSPENDM 0x1 /* enable SuspendM output */ +#define SUSPEND_MODE 0x2 /* Suspend Mode indicator */ +#define RESUME_MODE 0x4 /* DMA Mode */ +#define RESET 0x8 /* Reset indicator */ +#define HS_MODE 0x10 /* High Speed mode indicator */ +#define HS_ENABLE 0x20 /* high Speed Enable */ +#define SOFT_CONN 0x40 /* Soft connect */ +#define ISO_UPDATE 0x80 /* Isochronous update */ + +/* Bit masks for USB_INTRTX */ + +#define EP0_TX 0x1 /* Tx Endpoint 0 interrupt */ +#define EP1_TX 0x2 /* Tx Endpoint 1 interrupt */ +#define EP2_TX 0x4 /* Tx Endpoint 2 interrupt */ +#define EP3_TX 0x8 /* Tx Endpoint 3 interrupt */ +#define EP4_TX 0x10 /* Tx Endpoint 4 interrupt */ +#define EP5_TX 0x20 /* Tx Endpoint 5 interrupt */ +#define EP6_TX 0x40 /* Tx Endpoint 6 interrupt */ +#define EP7_TX 0x80 /* Tx Endpoint 7 interrupt */ + +/* Bit masks for USB_INTRRX */ + +#define EP1_RX 0x2 /* Rx Endpoint 1 interrupt */ +#define EP2_RX 0x4 /* Rx Endpoint 2 interrupt */ +#define EP3_RX 0x8 /* Rx Endpoint 3 interrupt */ +#define EP4_RX 0x10 /* Rx Endpoint 4 interrupt */ +#define EP5_RX 0x20 /* Rx Endpoint 5 interrupt */ +#define EP6_RX 0x40 /* Rx Endpoint 6 interrupt */ +#define EP7_RX 0x80 /* Rx Endpoint 7 interrupt */ + +/* Bit masks for USB_INTRTXE */ + +#define EP0_TX_E 0x1 /* Endpoint 0 interrupt Enable */ +#define EP1_TX_E 0x2 /* Tx Endpoint 1 interrupt enable */ +#define EP2_TX_E 0x4 /* Tx Endpoint 2 interrupt enable */ +#define EP3_TX_E 0x8 /* Tx Endpoint 3 interrupt enable */ +#define EP4_TX_E 0x10 /* Tx Endpoint 4 interrupt enable */ +#define EP5_TX_E 0x20 /* Tx Endpoint 5 interrupt enable */ +#define EP6_TX_E 0x40 /* Tx Endpoint 6 interrupt enable */ +#define EP7_TX_E 0x80 /* Tx Endpoint 7 interrupt enable */ + +/* Bit masks for USB_INTRRXE */ + +#define EP1_RX_E 0x02 /* Rx Endpoint 1 interrupt enable */ +#define EP2_RX_E 0x04 /* Rx Endpoint 2 interrupt enable */ +#define EP3_RX_E 0x08 /* Rx Endpoint 3 interrupt enable */ +#define EP4_RX_E 0x10 /* Rx Endpoint 4 interrupt enable */ +#define EP5_RX_E 0x20 /* Rx Endpoint 5 interrupt enable */ +#define EP6_RX_E 0x40 /* Rx Endpoint 6 interrupt enable */ +#define EP7_RX_E 0x80 /* Rx Endpoint 7 interrupt enable */ + +/* Bit masks for USB_INTRUSB */ + +#define SUSPEND_B 0x01 /* Suspend indicator */ +#define RESUME_B 0x02 /* Resume indicator */ +#define RESET_OR_BABLE_B 0x04 /* Reset/babble indicator */ +#define SOF_B 0x08 /* Start of frame */ +#define CONN_B 0x10 /* Connection indicator */ +#define DISCON_B 0x20 /* Disconnect indicator */ +#define SESSION_REQ_B 0x40 /* Session Request */ +#define VBUS_ERROR_B 0x80 /* Vbus threshold indicator */ + +/* Bit masks for USB_INTRUSBE */ + +#define SUSPEND_BE 0x01 /* Suspend indicator int enable */ +#define RESUME_BE 0x02 /* Resume indicator int enable */ +#define RESET_OR_BABLE_BE 0x04 /* Reset/babble indicator int enable */ +#define SOF_BE 0x08 /* Start of frame int enable */ +#define CONN_BE 0x10 /* Connection indicator int enable */ +#define DISCON_BE 0x20 /* Disconnect indicator int enable */ +#define SESSION_REQ_BE 0x40 /* Session Request int enable */ +#define VBUS_ERROR_BE 0x80 /* Vbus threshold indicator int enable */ + +/* Bit masks for USB_FRAME */ + +#define FRAME_NUMBER 0x7ff /* Frame number */ + +/* Bit masks for USB_INDEX */ + +#define SELECTED_ENDPOINT 0xf /* selected endpoint */ + +/* Bit masks for USB_GLOBAL_CTL */ + +#define GLOBAL_ENA 0x0001 /* enables USB module */ +#define EP1_TX_ENA 0x0002 /* Transmit endpoint 1 enable */ +#define EP2_TX_ENA 0x0004 /* Transmit endpoint 2 enable */ +#define EP3_TX_ENA 0x0008 /* Transmit endpoint 3 enable */ +#define EP4_TX_ENA 0x0010 /* Transmit endpoint 4 enable */ +#define EP5_TX_ENA 0x0020 /* Transmit endpoint 5 enable */ +#define EP6_TX_ENA 0x0040 /* Transmit endpoint 6 enable */ +#define EP7_TX_ENA 0x0080 /* Transmit endpoint 7 enable */ +#define EP1_RX_ENA 0x0100 /* Receive endpoint 1 enable */ +#define EP2_RX_ENA 0x0200 /* Receive endpoint 2 enable */ +#define EP3_RX_ENA 0x0400 /* Receive endpoint 3 enable */ +#define EP4_RX_ENA 0x0800 /* Receive endpoint 4 enable */ +#define EP5_RX_ENA 0x1000 /* Receive endpoint 5 enable */ +#define EP6_RX_ENA 0x2000 /* Receive endpoint 6 enable */ +#define EP7_RX_ENA 0x4000 /* Receive endpoint 7 enable */ + +/* Bit masks for USB_OTG_DEV_CTL */ + +#define SESSION 0x1 /* session indicator */ +#define HOST_REQ 0x2 /* Host negotiation request */ +#define HOST_MODE 0x4 /* indicates USBDRC is a host */ +#define VBUS0 0x8 /* Vbus level indicator[0] */ +#define VBUS1 0x10 /* Vbus level indicator[1] */ +#define LSDEV 0x20 /* Low-speed indicator */ +#define FSDEV 0x40 /* Full or High-speed indicator */ +#define B_DEVICE 0x80 /* A' or 'B' device indicator */ + +/* Bit masks for USB_OTG_VBUS_IRQ */ + +#define DRIVE_VBUS_ON 0x1 /* indicator to drive VBUS control circuit */ +#define DRIVE_VBUS_OFF 0x2 /* indicator to shut off charge pump */ +#define CHRG_VBUS_START 0x4 /* indicator for external circuit to start charging VBUS */ +#define CHRG_VBUS_END 0x8 /* indicator for external circuit to end charging VBUS */ +#define DISCHRG_VBUS_START 0x10 /* indicator to start discharging VBUS */ +#define DISCHRG_VBUS_END 0x20 /* indicator to stop discharging VBUS */ + +/* Bit masks for USB_OTG_VBUS_MASK */ + +#define DRIVE_VBUS_ON_ENA 0x01 /* enable DRIVE_VBUS_ON interrupt */ +#define DRIVE_VBUS_OFF_ENA 0x02 /* enable DRIVE_VBUS_OFF interrupt */ +#define CHRG_VBUS_START_ENA 0x04 /* enable CHRG_VBUS_START interrupt */ +#define CHRG_VBUS_END_ENA 0x08 /* enable CHRG_VBUS_END interrupt */ +#define DISCHRG_VBUS_START_ENA 0x10 /* enable DISCHRG_VBUS_START interrupt */ +#define DISCHRG_VBUS_END_ENA 0x20 /* enable DISCHRG_VBUS_END interrupt */ + +/* Bit masks for USB_CSR0 */ + +#define RXPKTRDY 0x1 /* data packet receive indicator */ +#define TXPKTRDY 0x2 /* data packet in FIFO indicator */ +#define STALL_SENT 0x4 /* STALL handshake sent */ +#define DATAEND 0x8 /* Data end indicator */ +#define SETUPEND 0x10 /* Setup end */ +#define SENDSTALL 0x20 /* Send STALL handshake */ +#define SERVICED_RXPKTRDY 0x40 /* used to clear the RxPktRdy bit */ +#define SERVICED_SETUPEND 0x80 /* used to clear the SetupEnd bit */ +#define FLUSHFIFO 0x100 /* flush endpoint FIFO */ +#define STALL_RECEIVED_H 0x4 /* STALL handshake received host mode */ +#define SETUPPKT_H 0x8 /* send Setup token host mode */ +#define ERROR_H 0x10 /* timeout error indicator host mode */ +#define REQPKT_H 0x20 /* Request an IN transaction host mode */ +#define STATUSPKT_H 0x40 /* Status stage transaction host mode */ +#define NAK_TIMEOUT_H 0x80 /* EP0 halted after a NAK host mode */ + +/* Bit masks for USB_COUNT0 */ + +#define EP0_RX_COUNT 0x7f /* number of received bytes in EP0 FIFO */ + +/* Bit masks for USB_NAKLIMIT0 */ + +#define EP0_NAK_LIMIT 0x1f /* frames/micro frames count after which EP0 timeouts */ + +/* Bit masks for USB_TX_MAX_PACKET */ + +#define MAX_PACKET_SIZE_T 0x7ff /* maximum data pay load in a frame */ + +/* Bit masks for USB_RX_MAX_PACKET */ + +#define MAX_PACKET_SIZE_R 0x7ff /* maximum data pay load in a frame */ + +/* Bit masks for USB_TXCSR */ + +#define TXPKTRDY_T 0x1 /* data packet in FIFO indicator */ +#define FIFO_NOT_EMPTY_T 0x2 /* FIFO not empty */ +#define UNDERRUN_T 0x4 /* TxPktRdy not set for an IN token */ +#define FLUSHFIFO_T 0x8 /* flush endpoint FIFO */ +#define STALL_SEND_T 0x10 /* issue a Stall handshake */ +#define STALL_SENT_T 0x20 /* Stall handshake transmitted */ +#define CLEAR_DATATOGGLE_T 0x40 /* clear endpoint data toggle */ +#define INCOMPTX_T 0x80 /* indicates that a large packet is split */ +#define DMAREQMODE_T 0x400 /* DMA mode (0 or 1) selection */ +#define FORCE_DATATOGGLE_T 0x800 /* Force data toggle */ +#define DMAREQ_ENA_T 0x1000 /* Enable DMA request for Tx EP */ +#define ISO_T 0x4000 /* enable Isochronous transfers */ +#define AUTOSET_T 0x8000 /* allows TxPktRdy to be set automatically */ +#define ERROR_TH 0x4 /* error condition host mode */ +#define STALL_RECEIVED_TH 0x20 /* Stall handshake received host mode */ +#define NAK_TIMEOUT_TH 0x80 /* NAK timeout host mode */ + +/* Bit masks for USB_TXCOUNT */ + +#define TX_COUNT 0x1fff /* Byte len for the selected endpoint Tx FIFO */ + +/* Bit masks for USB_RXCSR */ + +#define RXPKTRDY_R 0x1 /* data packet in FIFO indicator */ +#define FIFO_FULL_R 0x2 /* FIFO not empty */ +#define OVERRUN_R 0x4 /* TxPktRdy not set for an IN token */ +#define DATAERROR_R 0x8 /* Out packet cannot be loaded into Rx FIFO */ +#define FLUSHFIFO_R 0x10 /* flush endpoint FIFO */ +#define STALL_SEND_R 0x20 /* issue a Stall handshake */ +#define STALL_SENT_R 0x40 /* Stall handshake transmitted */ +#define CLEAR_DATATOGGLE_R 0x80 /* clear endpoint data toggle */ +#define INCOMPRX_R 0x100 /* indicates that a large packet is split */ +#define DMAREQMODE_R 0x800 /* DMA mode (0 or 1) selection */ +#define DISNYET_R 0x1000 /* disable Nyet handshakes */ +#define DMAREQ_ENA_R 0x2000 /* Enable DMA request for Tx EP */ +#define ISO_R 0x4000 /* enable Isochronous transfers */ +#define AUTOCLEAR_R 0x8000 /* allows TxPktRdy to be set automatically */ +#define ERROR_RH 0x4 /* TxPktRdy not set for an IN token host mode */ +#define REQPKT_RH 0x20 /* request an IN transaction host mode */ +#define STALL_RECEIVED_RH 0x40 /* Stall handshake received host mode */ +#define INCOMPRX_RH 0x100 /* large packet is split host mode */ +#define DMAREQMODE_RH 0x800 /* DMA mode (0 or 1) selection host mode */ +#define AUTOREQ_RH 0x4000 /* sets ReqPkt automatically host mode */ + +/* Bit masks for USB_RXCOUNT */ + +#define RX_COUNT 0x1fff /* Packet byte len in the Rx FIFO */ + +/* Bit masks for USB_TXTYPE */ + +#define TARGET_EP_NO_T 0xf /* EP number */ +#define PROTOCOL_T 0xc /* transfer type */ + +/* Bit masks for USB_TXINTERVAL */ + +#define TX_POLL_INTERVAL 0xff /* polling interval for selected Tx EP */ + +/* Bit masks for USB_RXTYPE */ + +#define TARGET_EP_NO_R 0xf /* EP number */ +#define PROTOCOL_R 0xc /* transfer type */ + +/* Bit masks for USB_RXINTERVAL */ + +#define RX_POLL_INTERVAL 0xff /* polling interval for selected Rx EP */ + +/* Bit masks for USB_DMA_INTERRUPT */ + +#define DMA0_INT 0x1 /* DMA0 pending interrupt */ +#define DMA1_INT 0x2 /* DMA1 pending interrupt */ +#define DMA2_INT 0x4 /* DMA2 pending interrupt */ +#define DMA3_INT 0x8 /* DMA3 pending interrupt */ +#define DMA4_INT 0x10 /* DMA4 pending interrupt */ +#define DMA5_INT 0x20 /* DMA5 pending interrupt */ +#define DMA6_INT 0x40 /* DMA6 pending interrupt */ +#define DMA7_INT 0x80 /* DMA7 pending interrupt */ + +/* Bit masks for USB_DMAxCONTROL */ + +#define DMA_ENA 0x1 /* DMA enable */ +#define DIRECTION 0x2 /* direction of DMA transfer */ +#define MODE 0x4 /* DMA Bus error */ +#define INT_ENA 0x8 /* Interrupt enable */ +#define EPNUM 0xf0 /* EP number */ +#define BUSERROR 0x100 /* DMA Bus error */ + +#endif diff --git a/include/usb.h b/include/usb.h index 2a9cd04eb9..a1f09d4d7a 100644 --- a/include/usb.h +++ b/include/usb.h @@ -132,7 +132,8 @@ struct usb_device { defined(CONFIG_USB_EHCI) || defined(CONFIG_USB_OHCI_NEW) || \ defined(CONFIG_USB_SL811HS) || defined(CONFIG_USB_ISP116X_HCD) || \ defined(CONFIG_USB_R8A66597_HCD) || defined(CONFIG_USB_DAVINCI) || \ - defined(CONFIG_USB_OMAP3) || defined(CONFIG_USB_DA8XX) + defined(CONFIG_USB_OMAP3) || defined(CONFIG_USB_DA8XX) || \ + defined(CONFIG_USB_BLACKFIN) int usb_lowlevel_init(void); int usb_lowlevel_stop(void); -- cgit From b301be0599d14be46fc088861bb798648844aea5 Mon Sep 17 00:00:00 2001 From: Sanjeev Premi Date: Thu, 24 Dec 2009 14:20:41 +0530 Subject: omap3: fix compile warning This patch fixes this warning during compile: omap3.c: In function 'musb_platform_init': omap3.c:126: warning: label 'end' defined but not used Problem reported by: Dirk Behme[dirk.behme@googlemail.com] Signed-off-by: Sanjeev Premi --- drivers/usb/musb/omap3.c | 3 +++ 1 file changed, 3 insertions(+) diff --git a/drivers/usb/musb/omap3.c b/drivers/usb/musb/omap3.c index ea98c3cac1..3bfd0a085f 100644 --- a/drivers/usb/musb/omap3.c +++ b/drivers/usb/musb/omap3.c @@ -123,7 +123,10 @@ int musb_platform_init(void) } ret = platform_needs_initialization; + +#ifdef CONFIG_TWL4030_USB end: +#endif return ret; } -- cgit From b416191a14770c6bcc6fd67be7decf8159b2baee Mon Sep 17 00:00:00 2001 From: Chris Zhang Date: Wed, 6 Jan 2010 13:34:04 -0800 Subject: Fix EHCI port reset. In USB ehci driver, the port reset is not terminated. EHCI spec says "A host controller must terminate the reset and stabilize the state of the port within 2 milliseconds". Without termination, a port stays at reset state. This is observed on ppc4xx(sequoia) boards. Signed-off-by: Chris Zhang --- drivers/usb/host/ehci-hcd.c | 3 +++ 1 file changed, 3 insertions(+) diff --git a/drivers/usb/host/ehci-hcd.c b/drivers/usb/host/ehci-hcd.c index ba85991e86..9ebeb4f23d 100644 --- a/drivers/usb/host/ehci-hcd.c +++ b/drivers/usb/host/ehci-hcd.c @@ -708,6 +708,9 @@ ehci_submit_root(struct usb_device *dev, unsigned long pipe, void *buffer, * root */ wait_ms(50); + /* terminate the reset */ + ehci_writel(status_reg, reg & ~EHCI_PS_PR); + wait_ms(2); portreset |= 1 << le16_to_cpu(req->index); } break; -- cgit From 5f82887feecd7895593401f1ccda866bfb299fbb Mon Sep 17 00:00:00 2001 From: Chris Zhang Date: Wed, 6 Jan 2010 13:34:05 -0800 Subject: Add ppc440epx USB ehci support. Currently ppc440epx uses OHCI for USB full-speed support. This change adds support for EHCI. Signed-off-by: Chris Zhang --- drivers/usb/host/Makefile | 1 + drivers/usb/host/ehci-ppc4xx.c | 48 ++++++++++++++++++++++++++++++++++++++++++ 2 files changed, 49 insertions(+) create mode 100644 drivers/usb/host/ehci-ppc4xx.c diff --git a/drivers/usb/host/Makefile b/drivers/usb/host/Makefile index 940d4a8b91..255679a186 100644 --- a/drivers/usb/host/Makefile +++ b/drivers/usb/host/Makefile @@ -36,6 +36,7 @@ COBJS-$(CONFIG_USB_SL811HS) += sl811-hcd.o # echi COBJS-$(CONFIG_USB_EHCI) += ehci-hcd.o COBJS-$(CONFIG_USB_EHCI_FSL) += ehci-fsl.o +COBJS-$(CONFIG_USB_EHCI_PPC4XX) += ehci-ppc4xx.o COBJS-$(CONFIG_USB_EHCI_IXP4XX) += ehci-ixp.o COBJS-$(CONFIG_USB_EHCI_KIRKWOOD) += ehci-kirkwood.o COBJS-$(CONFIG_USB_EHCI_PCI) += ehci-pci.o diff --git a/drivers/usb/host/ehci-ppc4xx.c b/drivers/usb/host/ehci-ppc4xx.c new file mode 100644 index 0000000000..946a0a07ef --- /dev/null +++ b/drivers/usb/host/ehci-ppc4xx.c @@ -0,0 +1,48 @@ +/* + * (C) Copyright 2010, Chris Zhang + * + * Author: Chris Zhang + * This code is based on ehci freescale driver + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ +#include +#include + +#include "ehci.h" +#include "ehci-core.h" + +/* + * Create the appropriate control structures to manage + * a new EHCI host controller. + */ +int ehci_hcd_init(void) +{ + hccr = (struct ehci_hccr *)(CONFIG_SYS_PPC4XX_USB_ADDR); + hcor = (struct ehci_hcor *)((uint32_t) hccr + + HC_LENGTH(ehci_readl(&hccr->cr_capbase))); + usb_dev_init(); + return 0; +} + +/* + * Destroy the appropriate control structures corresponding + * the the EHCI host controller. + */ +int ehci_hcd_stop(void) +{ + return 0; +} -- cgit From 559e2c87e45ae7261837d4945411c04833937d2a Mon Sep 17 00:00:00 2001 From: Chris Zhang Date: Wed, 6 Jan 2010 13:34:06 -0800 Subject: Adds EHCI definitions to sequoia board configuration file. Adds required definitions for EHCI support in sequoia configuration file. But still keeps the OHCI as default driver. Signed-off-by: Chris Zhang --- include/configs/sequoia.h | 16 +++++++++++++++- 1 file changed, 15 insertions(+), 1 deletion(-) diff --git a/include/configs/sequoia.h b/include/configs/sequoia.h index 5788d581af..568d9fc0cd 100644 --- a/include/configs/sequoia.h +++ b/include/configs/sequoia.h @@ -282,8 +282,20 @@ /* USB */ #ifdef CONFIG_440EPX + +#undef CONFIG_USB_EHCI /* OHCI by default */ + +#ifdef CONFIG_USB_EHCI +#define CONFIG_USB_EHCI_PPC4XX +#define CONFIG_SYS_PPC4XX_USB_ADDR 0xe0000300 +#define CONFIG_EHCI_HCD_INIT_AFTER_RESET +#define CONFIG_EHCI_MMIO_BIG_ENDIAN +#define CONFIG_EHCI_DESC_BIG_ENDIAN +#ifdef CONFIG_4xx_DCACHE +#define CONFIG_EHCI_DCACHE +#endif +#else /* CONFIG_USB_EHCI */ #define CONFIG_USB_OHCI_NEW -#define CONFIG_USB_STORAGE #define CONFIG_SYS_OHCI_BE_CONTROLLER #undef CONFIG_SYS_USB_OHCI_BOARD_INIT @@ -291,7 +303,9 @@ #define CONFIG_SYS_USB_OHCI_REGS_BASE CONFIG_SYS_USB_HOST #define CONFIG_SYS_USB_OHCI_SLOT_NAME "ppc440" #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15 +#endif +#define CONFIG_USB_STORAGE /* Comment this out to enable USB 1.1 device */ #define USB_2_0_DEVICE -- cgit From 321790f61bb92fead0fc01b8d055aa331d8dcf85 Mon Sep 17 00:00:00 2001 From: Bryan Wu Date: Sat, 9 Jan 2010 16:53:54 -0500 Subject: usb: musb: add virtual root hub control support For MUSB devices that do not support multipoint (hubs), we have to emulate a root hub so that we can support core operations like resetting ports. Signed-off-by: Bryan Wu Signed-off-by: Cliff Cai Signed-off-by: Mike Frysinger --- drivers/usb/musb/musb_hcd.c | 429 +++++++++++++++++++++++++++++++++++++++++++- drivers/usb/musb/musb_hcd.h | 55 ++++++ 2 files changed, 482 insertions(+), 2 deletions(-) diff --git a/drivers/usb/musb/musb_hcd.c b/drivers/usb/musb/musb_hcd.c index adb8c38527..dd2aa7f27c 100644 --- a/drivers/usb/musb/musb_hcd.c +++ b/drivers/usb/musb/musb_hcd.c @@ -35,6 +35,106 @@ static struct musb_epinfo epinfo[3] = { {MUSB_INTR_EP, 0, 64} /* EP2 - Interrupt IN - 64 Bytes */ }; +/* --- Virtual Root Hub ---------------------------------------------------- */ +#ifdef MUSB_NO_MULTIPOINT +static int rh_devnum; +static u32 port_status; + +/* Device descriptor */ +static u8 root_hub_dev_des[] = { + 0x12, /* __u8 bLength; */ + 0x01, /* __u8 bDescriptorType; Device */ + 0x00, /* __u16 bcdUSB; v1.1 */ + 0x02, + 0x09, /* __u8 bDeviceClass; HUB_CLASSCODE */ + 0x00, /* __u8 bDeviceSubClass; */ + 0x00, /* __u8 bDeviceProtocol; */ + 0x08, /* __u8 bMaxPacketSize0; 8 Bytes */ + 0x00, /* __u16 idVendor; */ + 0x00, + 0x00, /* __u16 idProduct; */ + 0x00, + 0x00, /* __u16 bcdDevice; */ + 0x00, + 0x00, /* __u8 iManufacturer; */ + 0x01, /* __u8 iProduct; */ + 0x00, /* __u8 iSerialNumber; */ + 0x01 /* __u8 bNumConfigurations; */ +}; + +/* Configuration descriptor */ +static u8 root_hub_config_des[] = { + 0x09, /* __u8 bLength; */ + 0x02, /* __u8 bDescriptorType; Configuration */ + 0x19, /* __u16 wTotalLength; */ + 0x00, + 0x01, /* __u8 bNumInterfaces; */ + 0x01, /* __u8 bConfigurationValue; */ + 0x00, /* __u8 iConfiguration; */ + 0x40, /* __u8 bmAttributes; + Bit 7: Bus-powered, 6: Self-powered, 5 Remote-wakwup, 4..0: resvd */ + 0x00, /* __u8 MaxPower; */ + + /* interface */ + 0x09, /* __u8 if_bLength; */ + 0x04, /* __u8 if_bDescriptorType; Interface */ + 0x00, /* __u8 if_bInterfaceNumber; */ + 0x00, /* __u8 if_bAlternateSetting; */ + 0x01, /* __u8 if_bNumEndpoints; */ + 0x09, /* __u8 if_bInterfaceClass; HUB_CLASSCODE */ + 0x00, /* __u8 if_bInterfaceSubClass; */ + 0x00, /* __u8 if_bInterfaceProtocol; */ + 0x00, /* __u8 if_iInterface; */ + + /* endpoint */ + 0x07, /* __u8 ep_bLength; */ + 0x05, /* __u8 ep_bDescriptorType; Endpoint */ + 0x81, /* __u8 ep_bEndpointAddress; IN Endpoint 1 */ + 0x03, /* __u8 ep_bmAttributes; Interrupt */ + 0x00, /* __u16 ep_wMaxPacketSize; ((MAX_ROOT_PORTS + 1) / 8 */ + 0x02, + 0xff /* __u8 ep_bInterval; 255 ms */ +}; + +static unsigned char root_hub_str_index0[] = { + 0x04, /* __u8 bLength; */ + 0x03, /* __u8 bDescriptorType; String-descriptor */ + 0x09, /* __u8 lang ID */ + 0x04, /* __u8 lang ID */ +}; + +static unsigned char root_hub_str_index1[] = { + 0x1c, /* __u8 bLength; */ + 0x03, /* __u8 bDescriptorType; String-descriptor */ + 'M', /* __u8 Unicode */ + 0, /* __u8 Unicode */ + 'U', /* __u8 Unicode */ + 0, /* __u8 Unicode */ + 'S', /* __u8 Unicode */ + 0, /* __u8 Unicode */ + 'B', /* __u8 Unicode */ + 0, /* __u8 Unicode */ + ' ', /* __u8 Unicode */ + 0, /* __u8 Unicode */ + 'R', /* __u8 Unicode */ + 0, /* __u8 Unicode */ + 'o', /* __u8 Unicode */ + 0, /* __u8 Unicode */ + 'o', /* __u8 Unicode */ + 0, /* __u8 Unicode */ + 't', /* __u8 Unicode */ + 0, /* __u8 Unicode */ + ' ', /* __u8 Unicode */ + 0, /* __u8 Unicode */ + 'H', /* __u8 Unicode */ + 0, /* __u8 Unicode */ + 'u', /* __u8 Unicode */ + 0, /* __u8 Unicode */ + 'b', /* __u8 Unicode */ + 0, /* __u8 Unicode */ +}; +#endif + /* * This function writes the data toggle value. */ @@ -411,18 +511,341 @@ static void config_hub_port(struct usb_device *dev, u8 ep) #endif } +#ifdef MUSB_NO_MULTIPOINT + +static void musb_port_reset(int do_reset) +{ + u8 power = readb(&musbr->power); + + if (do_reset) { + power &= 0xf0; + writeb(power | MUSB_POWER_RESET, &musbr->power); + port_status |= USB_PORT_STAT_RESET; + port_status &= ~USB_PORT_STAT_ENABLE; + udelay(30000); + } else { + writeb(power & ~MUSB_POWER_RESET, &musbr->power); + + power = readb(&musbr->power); + if (power & MUSB_POWER_HSMODE) + port_status |= USB_PORT_STAT_HIGH_SPEED; + + port_status &= ~(USB_PORT_STAT_RESET | (USB_PORT_STAT_C_CONNECTION << 16)); + port_status |= USB_PORT_STAT_ENABLE + | (USB_PORT_STAT_C_RESET << 16) + | (USB_PORT_STAT_C_ENABLE << 16); + } +} + +/* + * root hub control + */ +static int musb_submit_rh_msg(struct usb_device *dev, unsigned long pipe, + void *buffer, int transfer_len, + struct devrequest *cmd) +{ + int leni = transfer_len; + int len = 0; + int stat = 0; + u32 datab[4]; + u8 *data_buf = (u8 *) datab; + u16 bmRType_bReq; + u16 wValue; + u16 wIndex; + u16 wLength; + u16 int_usb; + + if ((pipe & PIPE_INTERRUPT) == PIPE_INTERRUPT) { + debug("Root-Hub submit IRQ: NOT implemented\n"); + return 0; + } + + bmRType_bReq = cmd->requesttype | (cmd->request << 8); + wValue = swap_16(cmd->value); + wIndex = swap_16(cmd->index); + wLength = swap_16(cmd->length); + + debug("--- HUB ----------------------------------------\n"); + debug("submit rh urb, req=%x val=%#x index=%#x len=%d\n", + bmRType_bReq, wValue, wIndex, wLength); + debug("------------------------------------------------\n"); + + switch (bmRType_bReq) { + case RH_GET_STATUS: + debug("RH_GET_STATUS\n"); + + *(__u16 *) data_buf = swap_16(1); + len = 2; + break; + + case RH_GET_STATUS | RH_INTERFACE: + debug("RH_GET_STATUS | RH_INTERFACE\n"); + + *(__u16 *) data_buf = swap_16(0); + len = 2; + break; + + case RH_GET_STATUS | RH_ENDPOINT: + debug("RH_GET_STATUS | RH_ENDPOINT\n"); + + *(__u16 *) data_buf = swap_16(0); + len = 2; + break; + + case RH_GET_STATUS | RH_CLASS: + debug("RH_GET_STATUS | RH_CLASS\n"); + + *(__u32 *) data_buf = swap_32(0); + len = 4; + break; + + case RH_GET_STATUS | RH_OTHER | RH_CLASS: + debug("RH_GET_STATUS | RH_OTHER | RH_CLASS\n"); + + int_usb = readw(&musbr->intrusb); + if (int_usb & MUSB_INTR_CONNECT) { + port_status |= USB_PORT_STAT_CONNECTION + | (USB_PORT_STAT_C_CONNECTION << 16); + port_status |= USB_PORT_STAT_HIGH_SPEED + | USB_PORT_STAT_ENABLE; + } + + if (port_status & USB_PORT_STAT_RESET) + musb_port_reset(0); + + *(__u32 *) data_buf = swap_32(port_status); + len = 4; + break; + + case RH_CLEAR_FEATURE | RH_ENDPOINT: + debug("RH_CLEAR_FEATURE | RH_ENDPOINT\n"); + + switch (wValue) { + case RH_ENDPOINT_STALL: + debug("C_HUB_ENDPOINT_STALL\n"); + len = 0; + break; + } + port_status &= ~(1 << wValue); + break; + + case RH_CLEAR_FEATURE | RH_CLASS: + debug("RH_CLEAR_FEATURE | RH_CLASS\n"); + + switch (wValue) { + case RH_C_HUB_LOCAL_POWER: + debug("C_HUB_LOCAL_POWER\n"); + len = 0; + break; + + case RH_C_HUB_OVER_CURRENT: + debug("C_HUB_OVER_CURRENT\n"); + len = 0; + break; + } + port_status &= ~(1 << wValue); + break; + + case RH_CLEAR_FEATURE | RH_OTHER | RH_CLASS: + debug("RH_CLEAR_FEATURE | RH_OTHER | RH_CLASS\n"); + + switch (wValue) { + case RH_PORT_ENABLE: + len = 0; + break; + + case RH_PORT_SUSPEND: + len = 0; + break; + + case RH_PORT_POWER: + len = 0; + break; + + case RH_C_PORT_CONNECTION: + len = 0; + break; + + case RH_C_PORT_ENABLE: + len = 0; + break; + + case RH_C_PORT_SUSPEND: + len = 0; + break; + + case RH_C_PORT_OVER_CURRENT: + len = 0; + break; + + case RH_C_PORT_RESET: + len = 0; + break; + + default: + debug("invalid wValue\n"); + stat = USB_ST_STALLED; + } + + port_status &= ~(1 << wValue); + break; + + case RH_SET_FEATURE | RH_OTHER | RH_CLASS: + debug("RH_SET_FEATURE | RH_OTHER | RH_CLASS\n"); + + switch (wValue) { + case RH_PORT_SUSPEND: + len = 0; + break; + + case RH_PORT_RESET: + musb_port_reset(1); + len = 0; + break; + + case RH_PORT_POWER: + len = 0; + break; + + case RH_PORT_ENABLE: + len = 0; + break; + + default: + debug("invalid wValue\n"); + stat = USB_ST_STALLED; + } + + port_status |= 1 << wValue; + break; + + case RH_SET_ADDRESS: + debug("RH_SET_ADDRESS\n"); + + rh_devnum = wValue; + len = 0; + break; + + case RH_GET_DESCRIPTOR: + debug("RH_GET_DESCRIPTOR: %x, %d\n", wValue, wLength); + + switch (wValue) { + case (USB_DT_DEVICE << 8): /* device descriptor */ + len = min_t(unsigned int, + leni, min_t(unsigned int, + sizeof(root_hub_dev_des), + wLength)); + data_buf = root_hub_dev_des; + break; + + case (USB_DT_CONFIG << 8): /* configuration descriptor */ + len = min_t(unsigned int, + leni, min_t(unsigned int, + sizeof(root_hub_config_des), + wLength)); + data_buf = root_hub_config_des; + break; + + case ((USB_DT_STRING << 8) | 0x00): /* string 0 descriptors */ + len = min_t(unsigned int, + leni, min_t(unsigned int, + sizeof(root_hub_str_index0), + wLength)); + data_buf = root_hub_str_index0; + break; + + case ((USB_DT_STRING << 8) | 0x01): /* string 1 descriptors */ + len = min_t(unsigned int, + leni, min_t(unsigned int, + sizeof(root_hub_str_index1), + wLength)); + data_buf = root_hub_str_index1; + break; + + default: + debug("invalid wValue\n"); + stat = USB_ST_STALLED; + } + + break; + + case RH_GET_DESCRIPTOR | RH_CLASS: + debug("RH_GET_DESCRIPTOR | RH_CLASS\n"); + + data_buf[0] = 0x09; /* min length; */ + data_buf[1] = 0x29; + data_buf[2] = 0x1; /* 1 port */ + data_buf[3] = 0x01; /* per-port power switching */ + data_buf[3] |= 0x10; /* no overcurrent reporting */ + + /* Corresponds to data_buf[4-7] */ + data_buf[4] = 0; + data_buf[5] = 5; + data_buf[6] = 0; + data_buf[7] = 0x02; + data_buf[8] = 0xff; + + len = min_t(unsigned int, leni, + min_t(unsigned int, data_buf[0], wLength)); + break; + + case RH_GET_CONFIGURATION: + debug("RH_GET_CONFIGURATION\n"); + + *(__u8 *) data_buf = 0x01; + len = 1; + break; + + case RH_SET_CONFIGURATION: + debug("RH_SET_CONFIGURATION\n"); + + len = 0; + break; + + default: + debug("*** *** *** unsupported root hub command *** *** ***\n"); + stat = USB_ST_STALLED; + } + + len = min_t(int, len, leni); + if (buffer != data_buf) + memcpy(buffer, data_buf, len); + + dev->act_len = len; + dev->status = stat; + debug("dev act_len %d, status %d\n", dev->act_len, dev->status); + + return stat; +} + +static void musb_rh_init(void) +{ + rh_devnum = 0; + port_status = 0; +} + +#else + +static void musb_rh_init(void) {} + +#endif + /* * do a control transfer */ int submit_control_msg(struct usb_device *dev, unsigned long pipe, void *buffer, int len, struct devrequest *setup) { -#ifndef MUSB_NO_MULTIPOINT int devnum = usb_pipedevice(pipe); -#endif u16 csr; u8 devspeed; +#ifdef MUSB_NO_MULTIPOINT + /* Control message is for the HUB? */ + if (devnum == rh_devnum) + return musb_submit_rh_msg(dev, pipe, buffer, len, setup); +#endif + /* select control endpoint */ writeb(MUSB_CONTROL_EP, &musbr->index); csr = readw(&musbr->txcsr); @@ -649,6 +1072,8 @@ int usb_lowlevel_init(void) u8 power; u32 timeout; + musb_rh_init(); + if (musb_platform_init() == -1) return -1; diff --git a/drivers/usb/musb/musb_hcd.h b/drivers/usb/musb/musb_hcd.h index a437985dc8..dde7d37722 100644 --- a/drivers/usb/musb/musb_hcd.h +++ b/drivers/usb/musb/musb_hcd.h @@ -50,6 +50,61 @@ extern unsigned char new[]; ((readb(&musbr->power) & MUSB_POWER_HSMODE) \ >> MUSB_POWER_HSMODE_SHIFT) +#define min_t(type, x, y) \ + ({ type __x = (x); type __y = (y); __x < __y ? __x : __y; }) + +/* USB HUB CONSTANTS (not OHCI-specific; see hub.h) */ + +/* destination of request */ +#define RH_INTERFACE 0x01 +#define RH_ENDPOINT 0x02 +#define RH_OTHER 0x03 + +#define RH_CLASS 0x20 +#define RH_VENDOR 0x40 + +/* Requests: bRequest << 8 | bmRequestType */ +#define RH_GET_STATUS 0x0080 +#define RH_CLEAR_FEATURE 0x0100 +#define RH_SET_FEATURE 0x0300 +#define RH_SET_ADDRESS 0x0500 +#define RH_GET_DESCRIPTOR 0x0680 +#define RH_SET_DESCRIPTOR 0x0700 +#define RH_GET_CONFIGURATION 0x0880 +#define RH_SET_CONFIGURATION 0x0900 +#define RH_GET_STATE 0x0280 +#define RH_GET_INTERFACE 0x0A80 +#define RH_SET_INTERFACE 0x0B00 +#define RH_SYNC_FRAME 0x0C80 +/* Our Vendor Specific Request */ +#define RH_SET_EP 0x2000 + +/* Hub port features */ +#define RH_PORT_CONNECTION 0x00 +#define RH_PORT_ENABLE 0x01 +#define RH_PORT_SUSPEND 0x02 +#define RH_PORT_OVER_CURRENT 0x03 +#define RH_PORT_RESET 0x04 +#define RH_PORT_POWER 0x08 +#define RH_PORT_LOW_SPEED 0x09 + +#define RH_C_PORT_CONNECTION 0x10 +#define RH_C_PORT_ENABLE 0x11 +#define RH_C_PORT_SUSPEND 0x12 +#define RH_C_PORT_OVER_CURRENT 0x13 +#define RH_C_PORT_RESET 0x14 + +/* Hub features */ +#define RH_C_HUB_LOCAL_POWER 0x00 +#define RH_C_HUB_OVER_CURRENT 0x01 + +#define RH_DEVICE_REMOTE_WAKEUP 0x00 +#define RH_ENDPOINT_STALL 0x01 + +#define RH_ACK 0x01 +#define RH_REQ_ERR -1 +#define RH_NACK 0x00 + /* extern functions */ extern int musb_platform_init(void); extern void musb_platform_deinit(void); -- cgit