From d141b75cbf628a1e16eeeda43b44bee1845b65bd Mon Sep 17 00:00:00 2001 From: Marcel Ziswiler Date: Fri, 8 Feb 2019 18:42:14 +0100 Subject: colibri_imx6: migrate mmc to using driver model Migrate MMC to using driver model. Signed-off-by: Marcel Ziswiler --- board/toradex/colibri_imx6/colibri_imx6.c | 38 ++++--------------------------- configs/colibri_imx6_defconfig | 1 + 2 files changed, 5 insertions(+), 34 deletions(-) diff --git a/board/toradex/colibri_imx6/colibri_imx6.c b/board/toradex/colibri_imx6/colibri_imx6.c index 0131d9a635..1238474d7e 100644 --- a/board/toradex/colibri_imx6/colibri_imx6.c +++ b/board/toradex/colibri_imx6/colibri_imx6.c @@ -77,6 +77,7 @@ iomux_v3_cfg_t const uart1_pads[] = { MX6_PAD_CSI0_DAT11__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), }; +#if defined(CONFIG_FSL_ESDHC) && defined(CONFIG_SPL_BUILD) /* Colibri MMC */ iomux_v3_cfg_t const usdhc1_pads[] = { MX6_PAD_SD1_CLK__SD1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), @@ -103,6 +104,7 @@ iomux_v3_cfg_t const usdhc3_pads[] = { MX6_PAD_SD3_DAT7__SD3_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL), MX6_PAD_SD3_RST__SD3_RESET | MUX_PAD_CTRL(USDHC_PAD_CTRL), }; +#endif /* CONFIG_FSL_ESDHC & CONFIG_SPL_BUILD */ iomux_v3_cfg_t const enet_pads[] = { MX6_PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL), @@ -310,7 +312,7 @@ int board_ehci_power(int port, int on) } #endif /* CONFIG_USB_EHCI_MX6 */ -#ifdef CONFIG_FSL_ESDHC +#if defined(CONFIG_FSL_ESDHC) && defined(CONFIG_SPL_BUILD) /* use the following sequence: eMMC, MMC */ struct fsl_esdhc_cfg usdhc_cfg[CONFIG_SYS_FSL_USDHC_NUM] = { {USDHC3_BASE_ADDR}, @@ -335,37 +337,6 @@ int board_mmc_getcd(struct mmc *mmc) int board_mmc_init(bd_t *bis) { -#ifndef CONFIG_SPL_BUILD - s32 status = 0; - u32 index = 0; - - usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK); - usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK); - - usdhc_cfg[0].max_bus_width = 8; - usdhc_cfg[1].max_bus_width = 4; - - for (index = 0; index < CONFIG_SYS_FSL_USDHC_NUM; ++index) { - switch (index) { - case 0: - imx_iomux_v3_setup_multiple_pads( - usdhc3_pads, ARRAY_SIZE(usdhc3_pads)); - break; - case 1: - imx_iomux_v3_setup_multiple_pads( - usdhc1_pads, ARRAY_SIZE(usdhc1_pads)); - break; - default: - printf("Warning: you configured more USDHC controllers (%d) then supported by the board (%d)\n", - index + 1, CONFIG_SYS_FSL_USDHC_NUM); - return status; - } - - status |= fsl_esdhc_initialize(bis, &usdhc_cfg[index]); - } - - return status; -#else /* !CONFIG_SPL_BUILD */ struct src *psrc = (struct src *)SRC_BASE_ADDR; unsigned reg = readl(&psrc->sbmr1) >> 11; /* @@ -397,9 +368,8 @@ int board_mmc_init(bd_t *bis) } return fsl_esdhc_initialize(bis, &usdhc_cfg[0]); -#endif /* !CONFIG_SPL_BUILD */ } -#endif /* CONFIG_FSL_ESDHC */ +#endif /* CONFIG_FSL_ESDHC & CONFIG_SPL_BUILD */ int board_phy_config(struct phy_device *phydev) { diff --git a/configs/colibri_imx6_defconfig b/configs/colibri_imx6_defconfig index 6fd050a99f..2ab7db44a8 100644 --- a/configs/colibri_imx6_defconfig +++ b/configs/colibri_imx6_defconfig @@ -54,6 +54,7 @@ CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y CONFIG_DFU_MMC=y CONFIG_DM_GPIO=y CONFIG_DM_I2C=y +CONFIG_DM_MMC=y CONFIG_FSL_ESDHC=y CONFIG_PHYLIB=y CONFIG_PHY_MICREL=y -- cgit