From 0d331c035a091c1c1af4180b40bd234e3b87e80a Mon Sep 17 00:00:00 2001
From: Peng Fan <peng.fan@nxp.com>
Date: Tue, 5 Mar 2019 02:32:49 +0000
Subject: imx: support i.MX8QM MEK board

Add i.MX8QM MEK board support.
Included a basic dts, enabled SPL FIT

Boot log as below:
U-Boot SPL 2019.01-rc1-00029-gf002213219 (Dec 24 2018 - 10:28:30 +0800)
Normal Boot
Trying to boot from MMC2_2

U-Boot 2019.01-rc1-00029-gf002213219 (Dec 24 2018 - 10:28:30 +0800)

CPU:   NXP i.MX8QM RevB A53 at 142933 MHz

Model: Freescale i.MX8QM MEK
Board: iMX8QM MEK
Build: SCFW 9330215b
Boot:  SD1
DRAM:  6 GiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... *** Warning - bad CRC, using default environment

In:    serial@5a060000
Out:   serial@5a060000
Err:   serial@5a060000
Net:
Error: ethernet@5b040000 address not set.
eth-1: ethernet@5b040000
Hit any key to stop autoboot:  0

Signed-off-by: Peng Fan <peng.fan@nxp.com>
---
 board/freescale/imx8qm_mek/README | 57 +++++++++++++++++++++++++++++++++++++++
 1 file changed, 57 insertions(+)
 create mode 100644 board/freescale/imx8qm_mek/README

(limited to 'board/freescale/imx8qm_mek/README')

diff --git a/board/freescale/imx8qm_mek/README b/board/freescale/imx8qm_mek/README
new file mode 100644
index 0000000000..c3523801ae
--- /dev/null
+++ b/board/freescale/imx8qm_mek/README
@@ -0,0 +1,57 @@
+U-Boot for the NXP i.MX8QM EVK board
+
+Quick Start
+===========
+
+- Build the ARM Trusted firmware binary
+- Get scfw_tcm.bin and ahab-container.img
+- Build U-Boot
+- Flash the binary into the SD card
+- Boot
+
+Get and Build the ARM Trusted firmware
+======================================
+
+$ git clone https://source.codeaurora.org/external/imx/imx-atf
+$ cd imx-atf/
+$ git checkout origin/imx_4.14.78_1.0.0_ga -b imx_4.14.78_1.0.0_ga
+$ make PLAT=imx8qm bl31
+
+Get scfw_tcm.bin and ahab-container.img
+==============================
+
+$ wget https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/imx-sc-firmware-1.1.bin
+$ chmod +x imx-sc-firmware-1.1.bin
+$ ./imx-sc-firmware-1.1.bin
+$ wget https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/firmware-imx-8.0.bin
+$ chmod +x firmware-imx-8.0.bin
+$ ./firmware-imx-8.0.bin
+
+Copy the following binaries to U-Boot folder:
+
+$ cp imx-atf/build/imx8qm/release/bl31.bin .
+$ cp u-boot/u-boot.bin .
+
+Copy the following firmwares U-Boot folder :
+
+$ cp firmware-imx-7.6/firmware/seco/ahab-container.img .
+$ cp imx-sc-firmware-0.7/mx8qm-mek-scfw-tcm.bin	.
+
+Build U-Boot
+============
+$ export ATF_LOAD_ADDR=0x80000000
+$ export BL33_LOAD_ADDR=0x80020000
+$ make imx8qm_mek_defconfig
+$ make flash.bin
+$ dd if=u-boot.itb of=flash.bin bs=512 seek=1984
+
+Flash the binary into the SD card
+=================================
+
+Burn the flash.bin binary to SD card offset 32KB:
+
+$ sudo dd if=flash.bin of=/dev/sd[x] bs=1024 seek=32
+
+Boot
+====
+Set Boot switch SW2: 1100.
-- 
cgit