From e95b4bdd8dcadeecd516406387604aa56b76804c Mon Sep 17 00:00:00 2001 From: Lukasz Majewski Date: Tue, 3 Sep 2019 16:38:43 +0200 Subject: DM: SPI: Convert display5 to use SPI with DM/DTS (but no in SPL) The DM/DTS support for SPI is disabled on purpose for SPL, as it is not supported as of time of this conversion. Signed-off-by: Lukasz Majewski --- board/liebherr/display5/common.c | 18 ------------------ board/liebherr/display5/common.h | 1 - board/liebherr/display5/display5.c | 37 ++++++++++++------------------------- 3 files changed, 12 insertions(+), 44 deletions(-) (limited to 'board/liebherr') diff --git a/board/liebherr/display5/common.c b/board/liebherr/display5/common.c index 754c442427..d2d174beaa 100644 --- a/board/liebherr/display5/common.c +++ b/board/liebherr/display5/common.c @@ -45,18 +45,6 @@ void displ5_set_iomux_misc_spl(void) } #ifdef CONFIG_MXC_SPI -iomux_v3_cfg_t const ecspi_pads[] = { - /* SPI3 */ - MX6_PAD_DISP0_DAT2__ECSPI3_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL), - MX6_PAD_DISP0_DAT1__ECSPI3_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL), - MX6_PAD_DISP0_DAT0__ECSPI3_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL), - MX6_PAD_DISP0_DAT3__ECSPI3_SS0 | MUX_PAD_CTRL(NO_PAD_CTRL), - MX6_PAD_DISP0_DAT4__ECSPI3_SS1 | MUX_PAD_CTRL(NO_PAD_CTRL), - MX6_PAD_DISP0_DAT5__ECSPI3_SS2 | MUX_PAD_CTRL(NO_PAD_CTRL), - MX6_PAD_DISP0_DAT6__ECSPI3_SS3 | MUX_PAD_CTRL(NO_PAD_CTRL), - MX6_PAD_DISP0_DAT7__ECSPI3_RDY | MUX_PAD_CTRL(NO_PAD_CTRL), -}; - iomux_v3_cfg_t const ecspi2_pads[] = { /* SPI2, NOR Flash nWP, CS0 */ MX6_PAD_CSI0_DAT10__ECSPI2_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL), @@ -79,14 +67,8 @@ void displ5_set_iomux_ecspi_spl(void) SETUP_IOMUX_PADS(ecspi2_pads); } -void displ5_set_iomux_ecspi(void) -{ - SETUP_IOMUX_PADS(ecspi_pads); -} - #else void displ5_set_iomux_ecspi_spl(void) {} -void displ5_set_iomux_ecspi(void) {} #endif #ifdef CONFIG_FSL_ESDHC_IMX diff --git a/board/liebherr/display5/common.h b/board/liebherr/display5/common.h index 231cefc960..2bbd934e7a 100644 --- a/board/liebherr/display5/common.h +++ b/board/liebherr/display5/common.h @@ -34,7 +34,6 @@ void displ5_set_iomux_uart_spl(void); void displ5_set_iomux_uart(void); void displ5_set_iomux_ecspi_spl(void); -void displ5_set_iomux_ecspi(void); void displ5_set_iomux_usdhc_spl(void); void displ5_set_iomux_misc_spl(void); diff --git a/board/liebherr/display5/display5.c b/board/liebherr/display5/display5.c index e008ea9a3f..541e3e94a5 100644 --- a/board/liebherr/display5/display5.c +++ b/board/liebherr/display5/display5.c @@ -19,7 +19,6 @@ #include #include #include -#include #include #include #include @@ -28,11 +27,6 @@ #include #include -#ifndef CONFIG_MXC_SPI -#error "CONFIG_SPI must be set for this board" -#error "Please check your config file" -#endif - #include "common.h" DECLARE_GLOBAL_DATA_PTR; @@ -140,21 +134,6 @@ iomux_v3_cfg_t const misc_pads[] = { MX6_PAD_EIM_D29__GPIO3_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL), }; -static void displ5_setup_ecspi(void) -{ - int ret; - - displ5_set_iomux_ecspi(); - - ret = gpio_request(IMX_GPIO_NR(5, 29), "spi2_cs0"); - if (!ret) - gpio_direction_output(IMX_GPIO_NR(5, 29), 1); - - ret = gpio_request(IMX_GPIO_NR(7, 0), "spi2_#wp"); - if (!ret) - gpio_direction_output(IMX_GPIO_NR(7, 0), 1); -} - /* * Do not overwrite the console * Always use serial for U-Boot console @@ -188,7 +167,7 @@ int board_phy_config(struct phy_device *phydev) int board_init(void) { - struct gpio_desc phy_int_gbe; + struct gpio_desc phy_int_gbe, spi2_wp; int ret; debug("board init\n"); @@ -197,9 +176,6 @@ int board_init(void) /* Setup iomux for non console UARTS */ displ5_set_iomux_uart(); - - displ5_setup_ecspi(); - /* Setup misc (application specific) stuff */ SETUP_IOMUX_PADS(misc_pads); @@ -229,6 +205,17 @@ int board_init(void) iomuxc_set_rgmii_io_voltage(DDR_SEL_1P5V_IO); enable_fec_anatop_clock(0, ENET_125MHZ); + /* Setup #WP for SPI-NOR memory */ + ret = dm_gpio_lookup_name("GPIO7_0", &spi2_wp); + if (ret) { + printf("Cannot get GPIO7_0\n"); + } else { + ret = dm_gpio_request(&spi2_wp, "spi2_#wp"); + if (!ret) + dm_gpio_set_dir_flags(&spi2_wp, GPIOD_IS_OUT | + GPIOD_IS_OUT_ACTIVE); + } + return 0; } -- cgit