From 8bbfb40e572ddb8a11482ca513131e21a75e99de Mon Sep 17 00:00:00 2001 From: Jerome Brunet Date: Fri, 19 Oct 2018 12:14:57 +0200 Subject: board: amlogic: remove p212 derivatives The Khadas vim and the libretech aml-s905x-cc (aka Potato) derive from amlogic s905x reference design (P212). All the code in these board is a copy/paste from the p212, which is tedious to maintain. This change use p212 u-boot board for all these boards, while keeping a dedicated defconfig to customize the names and device tree. Signed-off-by: Jerome Brunet Signed-off-by: Neil Armstrong --- board/amlogic/khadas-vim/Kconfig | 12 ---- board/amlogic/khadas-vim/MAINTAINERS | 6 -- board/amlogic/khadas-vim/Makefile | 6 -- board/amlogic/khadas-vim/README | 102 ----------------------------- board/amlogic/khadas-vim/khadas-vim.c | 57 ----------------- board/amlogic/libretech-cc/Kconfig | 12 ---- board/amlogic/libretech-cc/MAINTAINERS | 6 -- board/amlogic/libretech-cc/Makefile | 6 -- board/amlogic/libretech-cc/README | 102 ----------------------------- board/amlogic/libretech-cc/libretech-cc.c | 57 ----------------- board/amlogic/p212/README | 103 ------------------------------ board/amlogic/p212/README.khadas-vim | 102 +++++++++++++++++++++++++++++ board/amlogic/p212/README.libretech-cc | 102 +++++++++++++++++++++++++++++ board/amlogic/p212/README.p212 | 103 ++++++++++++++++++++++++++++++ 14 files changed, 307 insertions(+), 469 deletions(-) delete mode 100644 board/amlogic/khadas-vim/Kconfig delete mode 100644 board/amlogic/khadas-vim/MAINTAINERS delete mode 100644 board/amlogic/khadas-vim/Makefile delete mode 100644 board/amlogic/khadas-vim/README delete mode 100644 board/amlogic/khadas-vim/khadas-vim.c delete mode 100644 board/amlogic/libretech-cc/Kconfig delete mode 100644 board/amlogic/libretech-cc/MAINTAINERS delete mode 100644 board/amlogic/libretech-cc/Makefile delete mode 100644 board/amlogic/libretech-cc/README delete mode 100644 board/amlogic/libretech-cc/libretech-cc.c delete mode 100644 board/amlogic/p212/README create mode 100644 board/amlogic/p212/README.khadas-vim create mode 100644 board/amlogic/p212/README.libretech-cc create mode 100644 board/amlogic/p212/README.p212 (limited to 'board') diff --git a/board/amlogic/khadas-vim/Kconfig b/board/amlogic/khadas-vim/Kconfig deleted file mode 100644 index 0fa8db97ea..0000000000 --- a/board/amlogic/khadas-vim/Kconfig +++ /dev/null @@ -1,12 +0,0 @@ -if TARGET_KHADAS_VIM - -config SYS_BOARD - default "khadas-vim" - -config SYS_VENDOR - default "amlogic" - -config SYS_CONFIG_NAME - default "khadas-vim" - -endif diff --git a/board/amlogic/khadas-vim/MAINTAINERS b/board/amlogic/khadas-vim/MAINTAINERS deleted file mode 100644 index 024220a526..0000000000 --- a/board/amlogic/khadas-vim/MAINTAINERS +++ /dev/null @@ -1,6 +0,0 @@ -KHADAS-VIM -M: Neil Armstrong -S: Maintained -F: board/amlogic/khadas-vim/ -F: include/configs/khadas-vim.h -F: configs/khadas-vim_defconfig diff --git a/board/amlogic/khadas-vim/Makefile b/board/amlogic/khadas-vim/Makefile deleted file mode 100644 index 558c0769b7..0000000000 --- a/board/amlogic/khadas-vim/Makefile +++ /dev/null @@ -1,6 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0+ -# -# (C) Copyright 2016 BayLibre, SAS -# Author: Neil Armstrong - -obj-y := khadas-vim.o diff --git a/board/amlogic/khadas-vim/README b/board/amlogic/khadas-vim/README deleted file mode 100644 index b1942364f8..0000000000 --- a/board/amlogic/khadas-vim/README +++ /dev/null @@ -1,102 +0,0 @@ -U-Boot for Khadas VIM -======================= - -Khadas VIM is an Open Source DIY Box manufactured by Shenzhen Wesion -Technology Co., Ltd with the following specifications: - - - Amlogic S905X ARM Cortex-A53 quad-core SoC @ 1.5GHz - - ARM Mali 450 GPU - - 2GB DDR3 SDRAM - - 10/100 Ethernet - - HDMI 2.0 4K/60Hz display - - 40-pin GPIO header - - 2 x USB 2.0 Host, 1 x USB 2.0 Type-C OTG - - 8GB/16GBeMMC - - microSD - - SDIO Wifi Module, Bluetooth - - Two channels IR receiver - -Currently the u-boot port supports the following devices: - - serial - - eMMC, microSD - - Ethernet - - I2C - - Regulators - - Reset controller - - Clock controller - - USB Host - - ADC - -U-Boot compilation -================== - - > export ARCH=arm - > export CROSS_COMPILE=aarch64-none-elf- - > make khadas-vim_defconfig - > make - -Image creation -============== - -Amlogic doesn't provide sources for the firmware and for tools needed -to create the bootloader image, so it is necessary to obtain them from -the git tree published by the board vendor: - - > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz - > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz - > tar xvfJ gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz - > tar xvfJ gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz - > export PATH=$PWD/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux/bin:$PWD/gcc-linaro-arm-none-eabi-4.8-2013.11_linux/bin:$PATH - > git clone https://github.com/khadas/u-boot -b Vim vim-u-boot - > cd vim-u-boot - > make kvim_defconfig - > make - > export FIPDIR=$PWD/fip - -Go back to mainline U-Boot source tree then : - > mkdir fip - - > cp $FIPDIR/gxl/bl2.bin fip/ - > cp $FIPDIR/gxl/acs.bin fip/ - > cp $FIPDIR/gxl/bl21.bin fip/ - > cp $FIPDIR/gxl/bl30.bin fip/ - > cp $FIPDIR/gxl/bl301.bin fip/ - > cp $FIPDIR/gxl/bl31.img fip/ - > cp u-boot.bin fip/bl33.bin - - > $FIPDIR/blx_fix.sh \ - fip/bl30.bin \ - fip/zero_tmp \ - fip/bl30_zero.bin \ - fip/bl301.bin \ - fip/bl301_zero.bin \ - fip/bl30_new.bin \ - bl30 - - > python $FIPDIR/acs_tool.pyc fip/bl2.bin fip/bl2_acs.bin fip/acs.bin 0 - - > $FIPDIR/blx_fix.sh \ - fip/bl2_acs.bin \ - fip/zero_tmp \ - fip/bl2_zero.bin \ - fip/bl21.bin \ - fip/bl21_zero.bin \ - fip/bl2_new.bin \ - bl2 - - > $FIPDIR/gxl/aml_encrypt_gxl --bl3enc --input fip/bl30_new.bin - > $FIPDIR/gxl/aml_encrypt_gxl --bl3enc --input fip/bl31.img - > $FIPDIR/gxl/aml_encrypt_gxl --bl3enc --input fip/bl33.bin - > $FIPDIR/gxl/aml_encrypt_gxl --bl2sig --input fip/bl2_new.bin --output fip/bl2.n.bin.sig - > $FIPDIR/gxl/aml_encrypt_gxl --bootmk \ - --output fip/u-boot.bin \ - --bl2 fip/bl2.n.bin.sig \ - --bl30 fip/bl30_new.bin.enc \ - --bl31 fip/bl31.img.enc \ - --bl33 fip/bl33.bin.enc - -and then write the image to SD with: - - > DEV=/dev/your_sd_device - > dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=512 skip=1 seek=1 - > dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=1 count=444 diff --git a/board/amlogic/khadas-vim/khadas-vim.c b/board/amlogic/khadas-vim/khadas-vim.c deleted file mode 100644 index 692bf2add3..0000000000 --- a/board/amlogic/khadas-vim/khadas-vim.c +++ /dev/null @@ -1,57 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Copyright (C) 2016 BayLibre, SAS - * Author: Neil Armstrong - */ - -#include -#include -#include -#include -#include -#include -#include -#include - -#define EFUSE_SN_OFFSET 20 -#define EFUSE_SN_SIZE 16 -#define EFUSE_MAC_OFFSET 52 -#define EFUSE_MAC_SIZE 6 - -int board_init(void) -{ - return 0; -} - -int misc_init_r(void) -{ - u8 mac_addr[EFUSE_MAC_SIZE]; - char serial[EFUSE_SN_SIZE]; - ssize_t len; - - meson_gx_eth_init(PHY_INTERFACE_MODE_RMII, - MESON_GXL_USE_INTERNAL_RMII_PHY); - - if (!eth_env_get_enetaddr("ethaddr", mac_addr)) { - len = meson_sm_read_efuse(EFUSE_MAC_OFFSET, - mac_addr, EFUSE_MAC_SIZE); - if (len == EFUSE_MAC_SIZE && is_valid_ethaddr(mac_addr)) - eth_env_set_enetaddr("ethaddr", mac_addr); - } - - if (!env_get("serial#")) { - len = meson_sm_read_efuse(EFUSE_SN_OFFSET, serial, - EFUSE_SN_SIZE); - if (len == EFUSE_SN_SIZE) - env_set("serial#", serial); - } - - return 0; -} - -int ft_board_setup(void *blob, bd_t *bd) -{ - meson_gx_init_reserved_memory(blob); - - return 0; -} diff --git a/board/amlogic/libretech-cc/Kconfig b/board/amlogic/libretech-cc/Kconfig deleted file mode 100644 index 7a6f9169bd..0000000000 --- a/board/amlogic/libretech-cc/Kconfig +++ /dev/null @@ -1,12 +0,0 @@ -if TARGET_LIBRETECH_CC - -config SYS_BOARD - default "libretech-cc" - -config SYS_VENDOR - default "amlogic" - -config SYS_CONFIG_NAME - default "libretech-cc" - -endif diff --git a/board/amlogic/libretech-cc/MAINTAINERS b/board/amlogic/libretech-cc/MAINTAINERS deleted file mode 100644 index 398ce57db2..0000000000 --- a/board/amlogic/libretech-cc/MAINTAINERS +++ /dev/null @@ -1,6 +0,0 @@ -LIBRETECH-CC -M: Neil Armstrong -S: Maintained -F: board/amlogic/libretech-cc/ -F: include/configs/libretech-cc.h -F: configs/libretech-cc_defconfig diff --git a/board/amlogic/libretech-cc/Makefile b/board/amlogic/libretech-cc/Makefile deleted file mode 100644 index 3b0adf8bf5..0000000000 --- a/board/amlogic/libretech-cc/Makefile +++ /dev/null @@ -1,6 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0+ -# -# (C) Copyright 2016 BayLibre, SAS -# Author: Neil Armstrong - -obj-y := libretech-cc.o diff --git a/board/amlogic/libretech-cc/README b/board/amlogic/libretech-cc/README deleted file mode 100644 index d007f58764..0000000000 --- a/board/amlogic/libretech-cc/README +++ /dev/null @@ -1,102 +0,0 @@ -U-Boot for LibreTech CC -======================= - -LibreTech CC is a single board computer manufactured by Libre Technology -with the following specifications: - - - Amlogic S905X ARM Cortex-A53 quad-core SoC @ 1.5GHz - - ARM Mali 450 GPU - - 2GB DDR3 SDRAM - - 10/100 Ethernet - - HDMI 2.0 4K/60Hz display - - 40-pin GPIO header - - 4 x USB 2.0 Host - - eMMC, microSD - - Infrared receiver - -Schematics are available on the manufacturer website. - -Currently the U-Boot port supports the following devices: - - serial - - eMMC, microSD - - Ethernet - - I2C - - Regulators - - Reset controller - - Clock controller - - USB Host - - ADC - -U-Boot compilation -================== - - > export ARCH=arm - > export CROSS_COMPILE=aarch64-none-elf- - > make libretech-cc_defconfig - > make - -Image creation -============== - -Amlogic doesn't provide sources for the firmware and for tools needed -to create the bootloader image, so it is necessary to obtain them from -the git tree published by the board vendor: - - > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz - > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz - > tar xvfJ gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz - > tar xvfJ gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz - > export PATH=$PWD/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux/bin:$PWD/gcc-linaro-arm-none-eabi-4.8-2013.11_linux/bin:$PATH - > git clone https://github.com/BayLibre/u-boot.git -b libretech-cc amlogic-u-boot - > cd amlogic-u-boot - > make libretech_cc_defconfig - > make - > export FIPDIR=$PWD/fip - -Go back to mainline U-Boot source tree then : - > mkdir fip - - > cp $FIPDIR/gxl/bl2.bin fip/ - > cp $FIPDIR/gxl/acs.bin fip/ - > cp $FIPDIR/gxl/bl21.bin fip/ - > cp $FIPDIR/gxl/bl30.bin fip/ - > cp $FIPDIR/gxl/bl301.bin fip/ - > cp $FIPDIR/gxl/bl31.img fip/ - > cp u-boot.bin fip/bl33.bin - - > $FIPDIR/blx_fix.sh \ - fip/bl30.bin \ - fip/zero_tmp \ - fip/bl30_zero.bin \ - fip/bl301.bin \ - fip/bl301_zero.bin \ - fip/bl30_new.bin \ - bl30 - - > $FIPDIR/acs_tool.pyc fip/bl2.bin fip/bl2_acs.bin fip/acs.bin 0 - - > $FIPDIR/blx_fix.sh \ - fip/bl2_acs.bin \ - fip/zero_tmp \ - fip/bl2_zero.bin \ - fip/bl21.bin \ - fip/bl21_zero.bin \ - fip/bl2_new.bin \ - bl2 - - > $FIPDIR/gxl/aml_encrypt_gxl --bl3enc --input fip/bl30_new.bin - > $FIPDIR/gxl/aml_encrypt_gxl --bl3enc --input fip/bl31.img - > $FIPDIR/gxl/aml_encrypt_gxl --bl3enc --input fip/bl33.bin - > $FIPDIR/gxl/aml_encrypt_gxl --bl2sig --input fip/bl2_new.bin --output fip/bl2.n.bin.sig - > $FIPDIR/gxl/aml_encrypt_gxl --bootmk \ - --output fip/u-boot.bin \ - --bl2 fip/bl2.n.bin.sig \ - --bl30 fip/bl30_new.bin.enc \ - --bl31 fip/bl31.img.enc \ - --bl33 fip/bl33.bin.enc - -and then write the image to SD with: - - > DEV=/dev/your_sd_device - > dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=512 skip=1 seek=1 - > dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=1 count=444 diff --git a/board/amlogic/libretech-cc/libretech-cc.c b/board/amlogic/libretech-cc/libretech-cc.c deleted file mode 100644 index ccab1272c5..0000000000 --- a/board/amlogic/libretech-cc/libretech-cc.c +++ /dev/null @@ -1,57 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Copyright (C) 2016 BayLibre, SAS - * Author: Neil Armstrong - */ - -#include -#include -#include -#include -#include -#include -#include -#include - -#define EFUSE_SN_OFFSET 20 -#define EFUSE_SN_SIZE 16 -#define EFUSE_MAC_OFFSET 52 -#define EFUSE_MAC_SIZE 6 - -int board_init(void) -{ - return 0; -} - -int misc_init_r(void) -{ - u8 mac_addr[EFUSE_MAC_SIZE]; - char serial[EFUSE_SN_SIZE]; - ssize_t len; - - meson_gx_eth_init(PHY_INTERFACE_MODE_RMII, - MESON_GXL_USE_INTERNAL_RMII_PHY); - - if (!eth_env_get_enetaddr("ethaddr", mac_addr)) { - len = meson_sm_read_efuse(EFUSE_MAC_OFFSET, - mac_addr, EFUSE_MAC_SIZE); - if (len == EFUSE_MAC_SIZE && is_valid_ethaddr(mac_addr)) - eth_env_set_enetaddr("ethaddr", mac_addr); - } - - if (!env_get("serial#")) { - len = meson_sm_read_efuse(EFUSE_SN_OFFSET, serial, - EFUSE_SN_SIZE); - if (len == EFUSE_SN_SIZE) - env_set("serial#", serial); - } - - return 0; -} - -int ft_board_setup(void *blob, bd_t *bd) -{ - meson_gx_init_reserved_memory(blob); - - return 0; -} diff --git a/board/amlogic/p212/README b/board/amlogic/p212/README deleted file mode 100644 index ef5370c763..0000000000 --- a/board/amlogic/p212/README +++ /dev/null @@ -1,103 +0,0 @@ -U-Boot for Amlogic P212 -======================= - -P212 is a reference board manufactured by Amlogic with the following -specifications: - - - Amlogic S905X ARM Cortex-A53 quad-core SoC @ 1.5GHz - - ARM Mali 450 GPU - - 2GB DDR3 SDRAM - - 10/100 Ethernet - - HDMI 2.0 4K/60Hz display - - 2 x USB 2.0 Host - - eMMC, microSD - - Infrared receiver - - SDIO WiFi Module - - CVBS+Stereo Audio Jack - -Schematics are available from Amlogic on demand. - -Currently the u-boot port supports the following devices: - - serial - - eMMC, microSD - - Ethernet - - I2C - - Regulators - - Reset controller - - Clock controller - - USB Host - - ADC - -u-boot compilation -================== - - > export ARCH=arm - > export CROSS_COMPILE=aarch64-none-elf- - > make p212_defconfig - > make - -Image creation -============== - -Amlogic doesn't provide sources for the firmware and for tools needed -to create the bootloader image, so it is necessary to obtain them from -the git tree published by the board vendor: - - > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz - > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz - > tar xvfJ gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz - > tar xvfJ gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz - > export PATH=$PWD/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux/bin:$PWD/gcc-linaro-arm-none-eabi-4.8-2013.11_linux/bin:$PATH - > git clone https://github.com/BayLibre/u-boot.git -b n-amlogic-openlinux-20170606 amlogic-u-boot - > cd amlogic-u-boot - > make gxl_p212_v1_defconfig - > make - > export FIPDIR=$PWD/fip - -Go back to mainline U-boot source tree then : - > mkdir fip - - > cp $FIPDIR/gxl/bl2.bin fip/ - > cp $FIPDIR/gxl/acs.bin fip/ - > cp $FIPDIR/gxl/bl21.bin fip/ - > cp $FIPDIR/gxl/bl30.bin fip/ - > cp $FIPDIR/gxl/bl301.bin fip/ - > cp $FIPDIR/gxl/bl31.img fip/ - > cp u-boot.bin fip/bl33.bin - - > $FIPDIR/blx_fix.sh \ - fip/bl30.bin \ - fip/zero_tmp \ - fip/bl30_zero.bin \ - fip/bl301.bin \ - fip/bl301_zero.bin \ - fip/bl30_new.bin \ - bl30 - - > $FIPDIR/acs_tool.pyc fip/bl2.bin fip/bl2_acs.bin fip/acs.bin 0 - - > $FIPDIR/blx_fix.sh \ - fip/bl2_acs.bin \ - fip/zero_tmp \ - fip/bl2_zero.bin \ - fip/bl21.bin \ - fip/bl21_zero.bin \ - fip/bl2_new.bin \ - bl2 - - > $FIPDIR/gxl/aml_encrypt_gxl --bl3enc --input fip/bl30_new.bin - > $FIPDIR/gxl/aml_encrypt_gxl --bl3enc --input fip/bl31.img - > $FIPDIR/gxl/aml_encrypt_gxl --bl3enc --input fip/bl33.bin - > $FIPDIR/gxl/aml_encrypt_gxl --bl2sig --input fip/bl2_new.bin --output fip/bl2.n.bin.sig - > $FIPDIR/gxl/aml_encrypt_gxl --bootmk \ - --output fip/u-boot.bin \ - --bl2 fip/bl2.n.bin.sig \ - --bl30 fip/bl30_new.bin.enc \ - --bl31 fip/bl31.img.enc \ - --bl33 fip/bl33.bin.enc - -and then write the image to SD with: - - > DEV=/dev/your_sd_device - > dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=512 skip=1 seek=1 - > dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=1 count=444 diff --git a/board/amlogic/p212/README.khadas-vim b/board/amlogic/p212/README.khadas-vim new file mode 100644 index 0000000000..b1942364f8 --- /dev/null +++ b/board/amlogic/p212/README.khadas-vim @@ -0,0 +1,102 @@ +U-Boot for Khadas VIM +======================= + +Khadas VIM is an Open Source DIY Box manufactured by Shenzhen Wesion +Technology Co., Ltd with the following specifications: + + - Amlogic S905X ARM Cortex-A53 quad-core SoC @ 1.5GHz + - ARM Mali 450 GPU + - 2GB DDR3 SDRAM + - 10/100 Ethernet + - HDMI 2.0 4K/60Hz display + - 40-pin GPIO header + - 2 x USB 2.0 Host, 1 x USB 2.0 Type-C OTG + - 8GB/16GBeMMC + - microSD + - SDIO Wifi Module, Bluetooth + - Two channels IR receiver + +Currently the u-boot port supports the following devices: + - serial + - eMMC, microSD + - Ethernet + - I2C + - Regulators + - Reset controller + - Clock controller + - USB Host + - ADC + +U-Boot compilation +================== + + > export ARCH=arm + > export CROSS_COMPILE=aarch64-none-elf- + > make khadas-vim_defconfig + > make + +Image creation +============== + +Amlogic doesn't provide sources for the firmware and for tools needed +to create the bootloader image, so it is necessary to obtain them from +the git tree published by the board vendor: + + > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz + > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz + > tar xvfJ gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz + > tar xvfJ gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz + > export PATH=$PWD/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux/bin:$PWD/gcc-linaro-arm-none-eabi-4.8-2013.11_linux/bin:$PATH + > git clone https://github.com/khadas/u-boot -b Vim vim-u-boot + > cd vim-u-boot + > make kvim_defconfig + > make + > export FIPDIR=$PWD/fip + +Go back to mainline U-Boot source tree then : + > mkdir fip + + > cp $FIPDIR/gxl/bl2.bin fip/ + > cp $FIPDIR/gxl/acs.bin fip/ + > cp $FIPDIR/gxl/bl21.bin fip/ + > cp $FIPDIR/gxl/bl30.bin fip/ + > cp $FIPDIR/gxl/bl301.bin fip/ + > cp $FIPDIR/gxl/bl31.img fip/ + > cp u-boot.bin fip/bl33.bin + + > $FIPDIR/blx_fix.sh \ + fip/bl30.bin \ + fip/zero_tmp \ + fip/bl30_zero.bin \ + fip/bl301.bin \ + fip/bl301_zero.bin \ + fip/bl30_new.bin \ + bl30 + + > python $FIPDIR/acs_tool.pyc fip/bl2.bin fip/bl2_acs.bin fip/acs.bin 0 + + > $FIPDIR/blx_fix.sh \ + fip/bl2_acs.bin \ + fip/zero_tmp \ + fip/bl2_zero.bin \ + fip/bl21.bin \ + fip/bl21_zero.bin \ + fip/bl2_new.bin \ + bl2 + + > $FIPDIR/gxl/aml_encrypt_gxl --bl3enc --input fip/bl30_new.bin + > $FIPDIR/gxl/aml_encrypt_gxl --bl3enc --input fip/bl31.img + > $FIPDIR/gxl/aml_encrypt_gxl --bl3enc --input fip/bl33.bin + > $FIPDIR/gxl/aml_encrypt_gxl --bl2sig --input fip/bl2_new.bin --output fip/bl2.n.bin.sig + > $FIPDIR/gxl/aml_encrypt_gxl --bootmk \ + --output fip/u-boot.bin \ + --bl2 fip/bl2.n.bin.sig \ + --bl30 fip/bl30_new.bin.enc \ + --bl31 fip/bl31.img.enc \ + --bl33 fip/bl33.bin.enc + +and then write the image to SD with: + + > DEV=/dev/your_sd_device + > dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=512 skip=1 seek=1 + > dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=1 count=444 diff --git a/board/amlogic/p212/README.libretech-cc b/board/amlogic/p212/README.libretech-cc new file mode 100644 index 0000000000..d007f58764 --- /dev/null +++ b/board/amlogic/p212/README.libretech-cc @@ -0,0 +1,102 @@ +U-Boot for LibreTech CC +======================= + +LibreTech CC is a single board computer manufactured by Libre Technology +with the following specifications: + + - Amlogic S905X ARM Cortex-A53 quad-core SoC @ 1.5GHz + - ARM Mali 450 GPU + - 2GB DDR3 SDRAM + - 10/100 Ethernet + - HDMI 2.0 4K/60Hz display + - 40-pin GPIO header + - 4 x USB 2.0 Host + - eMMC, microSD + - Infrared receiver + +Schematics are available on the manufacturer website. + +Currently the U-Boot port supports the following devices: + - serial + - eMMC, microSD + - Ethernet + - I2C + - Regulators + - Reset controller + - Clock controller + - USB Host + - ADC + +U-Boot compilation +================== + + > export ARCH=arm + > export CROSS_COMPILE=aarch64-none-elf- + > make libretech-cc_defconfig + > make + +Image creation +============== + +Amlogic doesn't provide sources for the firmware and for tools needed +to create the bootloader image, so it is necessary to obtain them from +the git tree published by the board vendor: + + > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz + > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz + > tar xvfJ gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz + > tar xvfJ gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz + > export PATH=$PWD/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux/bin:$PWD/gcc-linaro-arm-none-eabi-4.8-2013.11_linux/bin:$PATH + > git clone https://github.com/BayLibre/u-boot.git -b libretech-cc amlogic-u-boot + > cd amlogic-u-boot + > make libretech_cc_defconfig + > make + > export FIPDIR=$PWD/fip + +Go back to mainline U-Boot source tree then : + > mkdir fip + + > cp $FIPDIR/gxl/bl2.bin fip/ + > cp $FIPDIR/gxl/acs.bin fip/ + > cp $FIPDIR/gxl/bl21.bin fip/ + > cp $FIPDIR/gxl/bl30.bin fip/ + > cp $FIPDIR/gxl/bl301.bin fip/ + > cp $FIPDIR/gxl/bl31.img fip/ + > cp u-boot.bin fip/bl33.bin + + > $FIPDIR/blx_fix.sh \ + fip/bl30.bin \ + fip/zero_tmp \ + fip/bl30_zero.bin \ + fip/bl301.bin \ + fip/bl301_zero.bin \ + fip/bl30_new.bin \ + bl30 + + > $FIPDIR/acs_tool.pyc fip/bl2.bin fip/bl2_acs.bin fip/acs.bin 0 + + > $FIPDIR/blx_fix.sh \ + fip/bl2_acs.bin \ + fip/zero_tmp \ + fip/bl2_zero.bin \ + fip/bl21.bin \ + fip/bl21_zero.bin \ + fip/bl2_new.bin \ + bl2 + + > $FIPDIR/gxl/aml_encrypt_gxl --bl3enc --input fip/bl30_new.bin + > $FIPDIR/gxl/aml_encrypt_gxl --bl3enc --input fip/bl31.img + > $FIPDIR/gxl/aml_encrypt_gxl --bl3enc --input fip/bl33.bin + > $FIPDIR/gxl/aml_encrypt_gxl --bl2sig --input fip/bl2_new.bin --output fip/bl2.n.bin.sig + > $FIPDIR/gxl/aml_encrypt_gxl --bootmk \ + --output fip/u-boot.bin \ + --bl2 fip/bl2.n.bin.sig \ + --bl30 fip/bl30_new.bin.enc \ + --bl31 fip/bl31.img.enc \ + --bl33 fip/bl33.bin.enc + +and then write the image to SD with: + + > DEV=/dev/your_sd_device + > dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=512 skip=1 seek=1 + > dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=1 count=444 diff --git a/board/amlogic/p212/README.p212 b/board/amlogic/p212/README.p212 new file mode 100644 index 0000000000..ef5370c763 --- /dev/null +++ b/board/amlogic/p212/README.p212 @@ -0,0 +1,103 @@ +U-Boot for Amlogic P212 +======================= + +P212 is a reference board manufactured by Amlogic with the following +specifications: + + - Amlogic S905X ARM Cortex-A53 quad-core SoC @ 1.5GHz + - ARM Mali 450 GPU + - 2GB DDR3 SDRAM + - 10/100 Ethernet + - HDMI 2.0 4K/60Hz display + - 2 x USB 2.0 Host + - eMMC, microSD + - Infrared receiver + - SDIO WiFi Module + - CVBS+Stereo Audio Jack + +Schematics are available from Amlogic on demand. + +Currently the u-boot port supports the following devices: + - serial + - eMMC, microSD + - Ethernet + - I2C + - Regulators + - Reset controller + - Clock controller + - USB Host + - ADC + +u-boot compilation +================== + + > export ARCH=arm + > export CROSS_COMPILE=aarch64-none-elf- + > make p212_defconfig + > make + +Image creation +============== + +Amlogic doesn't provide sources for the firmware and for tools needed +to create the bootloader image, so it is necessary to obtain them from +the git tree published by the board vendor: + + > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz + > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz + > tar xvfJ gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz + > tar xvfJ gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz + > export PATH=$PWD/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux/bin:$PWD/gcc-linaro-arm-none-eabi-4.8-2013.11_linux/bin:$PATH + > git clone https://github.com/BayLibre/u-boot.git -b n-amlogic-openlinux-20170606 amlogic-u-boot + > cd amlogic-u-boot + > make gxl_p212_v1_defconfig + > make + > export FIPDIR=$PWD/fip + +Go back to mainline U-boot source tree then : + > mkdir fip + + > cp $FIPDIR/gxl/bl2.bin fip/ + > cp $FIPDIR/gxl/acs.bin fip/ + > cp $FIPDIR/gxl/bl21.bin fip/ + > cp $FIPDIR/gxl/bl30.bin fip/ + > cp $FIPDIR/gxl/bl301.bin fip/ + > cp $FIPDIR/gxl/bl31.img fip/ + > cp u-boot.bin fip/bl33.bin + + > $FIPDIR/blx_fix.sh \ + fip/bl30.bin \ + fip/zero_tmp \ + fip/bl30_zero.bin \ + fip/bl301.bin \ + fip/bl301_zero.bin \ + fip/bl30_new.bin \ + bl30 + + > $FIPDIR/acs_tool.pyc fip/bl2.bin fip/bl2_acs.bin fip/acs.bin 0 + + > $FIPDIR/blx_fix.sh \ + fip/bl2_acs.bin \ + fip/zero_tmp \ + fip/bl2_zero.bin \ + fip/bl21.bin \ + fip/bl21_zero.bin \ + fip/bl2_new.bin \ + bl2 + + > $FIPDIR/gxl/aml_encrypt_gxl --bl3enc --input fip/bl30_new.bin + > $FIPDIR/gxl/aml_encrypt_gxl --bl3enc --input fip/bl31.img + > $FIPDIR/gxl/aml_encrypt_gxl --bl3enc --input fip/bl33.bin + > $FIPDIR/gxl/aml_encrypt_gxl --bl2sig --input fip/bl2_new.bin --output fip/bl2.n.bin.sig + > $FIPDIR/gxl/aml_encrypt_gxl --bootmk \ + --output fip/u-boot.bin \ + --bl2 fip/bl2.n.bin.sig \ + --bl30 fip/bl30_new.bin.enc \ + --bl31 fip/bl31.img.enc \ + --bl33 fip/bl33.bin.enc + +and then write the image to SD with: + + > DEV=/dev/your_sd_device + > dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=512 skip=1 seek=1 + > dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=1 count=444 -- cgit