From 0dc579f36c912188c42122574911cf4e64fc357c Mon Sep 17 00:00:00 2001 From: Przemyslaw Marczak Date: Mon, 1 Sep 2014 13:50:42 +0200 Subject: samsung: misc: fix soc revision setting in the set_board_info() The byte order of soc revision was inverted, now it is fixed. Signed-off-by: Przemyslaw Marczak Cc: Minkyu Kang Signed-off-by: Minkyu Kang --- board/samsung/common/misc.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'board') diff --git a/board/samsung/common/misc.c b/board/samsung/common/misc.c index 03106fdb9f..a453a82f40 100644 --- a/board/samsung/common/misc.c +++ b/board/samsung/common/misc.c @@ -26,8 +26,8 @@ void set_board_info(void) { char info[64]; - snprintf(info, ARRAY_SIZE(info), "%d.%d", s5p_cpu_rev & 0x0f, - (s5p_cpu_rev & 0xf0) >> 0x04); + snprintf(info, ARRAY_SIZE(info), "%u.%u", (s5p_cpu_rev & 0xf0) >> 4, + s5p_cpu_rev & 0xf); setenv("soc_rev", info); snprintf(info, ARRAY_SIZE(info), "%x", s5p_cpu_id); -- cgit From 33a4fcf637c306d43109b37d55bb718c069b8cdf Mon Sep 17 00:00:00 2001 From: Przemyslaw Marczak Date: Mon, 1 Sep 2014 13:50:45 +0200 Subject: board:samsung: check the boot device and init the right mmc driver. It is possible to boot device using a micro SD or eMMC slots. In this situation, boot device should be registered as a block device 0 in the MMC framework, because CONFIG_SYS_MMC_ENV_DEV is usually set to "0" in the most config cases. Signed-off-by: Przemyslaw Marczak Signed-off-by: Minkyu Kang --- board/samsung/common/board.c | 37 +++++++++++++++++++++++++++---------- 1 file changed, 27 insertions(+), 10 deletions(-) (limited to 'board') diff --git a/board/samsung/common/board.c b/board/samsung/common/board.c index 9dc7c832e6..1fa0e51b3e 100644 --- a/board/samsung/common/board.c +++ b/board/samsung/common/board.c @@ -240,22 +240,39 @@ int board_eth_init(bd_t *bis) } #ifdef CONFIG_GENERIC_MMC -int board_mmc_init(bd_t *bis) +static int init_mmc(void) +{ +#ifdef CONFIG_SDHCI + return exynos_mmc_init(gd->fdt_blob); +#else + return 0; +#endif +} + +static int init_dwmmc(void) { - int ret; #ifdef CONFIG_DWMMC - /* dwmmc initializattion for available channels */ - ret = exynos_dwmmc_init(gd->fdt_blob); - if (ret) - debug("dwmmc init failed\n"); + return exynos_dwmmc_init(gd->fdt_blob); +#else + return 0; #endif +} + +int board_mmc_init(bd_t *bis) +{ + int ret; + + if (get_boot_mode() == BOOT_MODE_SD) { + ret = init_mmc(); + ret |= init_dwmmc(); + } else { + ret = init_dwmmc(); + ret |= init_mmc(); + } -#ifdef CONFIG_SDHCI - /* mmc initializattion for available channels */ - ret = exynos_mmc_init(gd->fdt_blob); if (ret) debug("mmc init failed\n"); -#endif + return ret; } #endif -- cgit From 1d07c1013c717bd79bb2bd7a94861fbeb2067176 Mon Sep 17 00:00:00 2001 From: Przemyslaw Marczak Date: Mon, 1 Sep 2014 13:50:46 +0200 Subject: samsung: misc: add function for setting $dfu_alt_info This change introduces new common function: - set_dfu_alt_info() - put dfu system and bootloader setting into $dfu_alt_info. functions declaration: - char *get_dfu_alt_system(void) - char *get_dfu_alt_boot(void) - void set_dfu_alt_info(void) and new config: - CONFIG_SET_DFU_ALT_INFO This function can be used for auto setting dfu configuration on boot. Such feature is useful for multi board support by one u-boot binary. Each board should define two functions: - get_dfu_alt_system() - get_dfu_alt_boot() Signed-off-by: Przemyslaw Marczak Cc: Minkyu Kang Signed-off-by: Minkyu Kang --- board/samsung/common/misc.c | 41 +++++++++++++++++++++++++++++++++++++++++ 1 file changed, 41 insertions(+) (limited to 'board') diff --git a/board/samsung/common/misc.c b/board/samsung/common/misc.c index a453a82f40..9e5245230a 100644 --- a/board/samsung/common/misc.c +++ b/board/samsung/common/misc.c @@ -11,6 +11,7 @@ #include #include #include +#include #include #include #include @@ -21,6 +22,46 @@ DECLARE_GLOBAL_DATA_PTR; +#ifdef CONFIG_SET_DFU_ALT_INFO +void set_dfu_alt_info(void) +{ + size_t buf_size = CONFIG_SET_DFU_ALT_BUF_LEN; + ALLOC_CACHE_ALIGN_BUFFER(char, buf, buf_size); + char *alt_info = "Settings not found!"; + char *status = "error!\n"; + char *alt_setting; + char *alt_sep; + int offset = 0; + + puts("DFU alt info setting: "); + + alt_setting = get_dfu_alt_boot(); + if (alt_setting) { + setenv("dfu_alt_boot", alt_setting); + offset = snprintf(buf, buf_size, "%s", alt_setting); + } + + alt_setting = get_dfu_alt_system(); + if (alt_setting) { + if (offset) + alt_sep = ";"; + else + alt_sep = ""; + + offset += snprintf(buf + offset, buf_size - offset, + "%s%s", alt_sep, alt_setting); + } + + if (offset) { + alt_info = buf; + status = "done\n"; + } + + setenv("dfu_alt_info", alt_info); + puts(status); +} +#endif + #ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG void set_board_info(void) { -- cgit From 32ee9bc5ed615497179a4b0e38322d1a250f2c79 Mon Sep 17 00:00:00 2001 From: Przemyslaw Marczak Date: Mon, 1 Sep 2014 13:50:47 +0200 Subject: samsung:board: misc_init_r: call set_dfu_alt_info() This change enable automatic setting of dfu alt info on every boot. This is useful in case of booting one u-boot binary from multiple media. Signed-off-by: Przemyslaw Marczak Signed-off-by: Minkyu Kang --- board/samsung/common/board.c | 3 +++ 1 file changed, 3 insertions(+) (limited to 'board') diff --git a/board/samsung/common/board.c b/board/samsung/common/board.c index 1fa0e51b3e..56938135a9 100644 --- a/board/samsung/common/board.c +++ b/board/samsung/common/board.c @@ -324,6 +324,9 @@ int arch_early_init_r(void) #ifdef CONFIG_MISC_INIT_R int misc_init_r(void) { +#ifdef CONFIG_SET_DFU_ALT_INFO + set_dfu_alt_info(); +#endif #ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG set_board_info(); #endif -- cgit From d50c41efcd6621481dbf4ff25331badf980cb429 Mon Sep 17 00:00:00 2001 From: Przemyslaw Marczak Date: Mon, 1 Sep 2014 13:50:49 +0200 Subject: samsung: board: enable support of multiple board types This change adds declaration of functions: - set_board_type() - called at board_early_init_f() - get_board_type() - called at checkboard() For supporting multiple board types in a one config - it is welcome to display the current board model. This is what get_board_type() should return. Signed-off-by: Przemyslaw Marczak Cc: Minkyu Kang Signed-off-by: Minkyu Kang --- board/samsung/common/board.c | 15 ++++++++++----- 1 file changed, 10 insertions(+), 5 deletions(-) (limited to 'board') diff --git a/board/samsung/common/board.c b/board/samsung/common/board.c index 56938135a9..3d1cf437fa 100644 --- a/board/samsung/common/board.c +++ b/board/samsung/common/board.c @@ -137,7 +137,9 @@ static int board_uart_init(void) int board_early_init_f(void) { int err; - +#ifdef CONFIG_BOARD_TYPES + set_board_type(); +#endif err = board_uart_init(); if (err) { debug("UART init failed\n"); @@ -147,7 +149,6 @@ int board_early_init_f(void) #ifdef CONFIG_SYS_I2C_INIT_BOARD board_i2c_init(gd->fdt_blob); #endif - return exynos_early_init_f(); } #endif @@ -280,11 +281,15 @@ int board_mmc_init(bd_t *bis) #ifdef CONFIG_DISPLAY_BOARDINFO int checkboard(void) { - const char *board_name; + const char *board_info; - board_name = fdt_getprop(gd->fdt_blob, 0, "model", NULL); - printf("Board: %s\n", board_name ? board_name : "unknown"); + board_info = fdt_getprop(gd->fdt_blob, 0, "model", NULL); + printf("Board: %s\n", board_info ? board_info : "unknown"); +#ifdef CONFIG_BOARD_TYPES + board_info = get_board_type(); + printf("Model: %s\n", board_info ? board_info : "unknown"); +#endif return 0; } #endif -- cgit From c9c36bf56e4c6a7df3ea5abafbd993df265c9538 Mon Sep 17 00:00:00 2001 From: Przemyslaw Marczak Date: Mon, 1 Sep 2014 13:50:50 +0200 Subject: samsung: misc: use board specific functions to set env board info This change adds setup of environmental board info using get_board_name() and get_board_type() functions for config CONFIG_BOARD_TYPES. This is useful in case of running many boards with just one config. Signed-off-by: Przemyslaw Marczak Cc: Minkyu Kang Signed-off-by: Minkyu Kang --- board/samsung/common/misc.c | 12 ++++++++++-- 1 file changed, 10 insertions(+), 2 deletions(-) (limited to 'board') diff --git a/board/samsung/common/misc.c b/board/samsung/common/misc.c index 9e5245230a..8766f0ca06 100644 --- a/board/samsung/common/misc.c +++ b/board/samsung/common/misc.c @@ -79,8 +79,16 @@ void set_board_info(void) setenv("board_rev", info); #endif #ifdef CONFIG_OF_LIBFDT - snprintf(info, ARRAY_SIZE(info), "%s%x-%s.dtb", - CONFIG_SYS_SOC, s5p_cpu_id, CONFIG_SYS_BOARD); + const char *bdtype = ""; + const char *bdname = CONFIG_SYS_BOARD; + +#ifdef CONFIG_BOARD_TYPES + bdtype = get_board_type(); + sprintf(info, "%s%s", bdname, bdtype); + setenv("boardname", info); +#endif + snprintf(info, ARRAY_SIZE(info), "%s%x-%s%s.dtb", + CONFIG_SYS_SOC, s5p_cpu_id, bdname, bdtype); setenv("fdtfile", info); #endif } -- cgit From bf3a08bec8f4cb0328eead7c4ac2c1bb9cd2ad35 Mon Sep 17 00:00:00 2001 From: Przemyslaw Marczak Date: Mon, 1 Sep 2014 13:50:51 +0200 Subject: odroid: add board file for Odroid X2/U3 based on Samsung Exynos4412 This board file supports standard features of Odroid X2 and U3 boards: - Exynos4412 core clock set to 1000MHz and MPLL peripherial clock set to 800MHz, - MAX77686 power regulator, - USB PHY, - enable XCL205 - power for board peripherials - check board type: U3 or X2. - enable Odroid U3 FAN cooler Signed-off-by: Przemyslaw Marczak Cc: Minkyu Kang Cc: Tom Rini Signed-off-by: Minkyu Kang --- board/samsung/odroid/Makefile | 8 + board/samsung/odroid/odroid.c | 470 ++++++++++++++++++++++++++++++++++++++++++ board/samsung/odroid/setup.h | 255 +++++++++++++++++++++++ 3 files changed, 733 insertions(+) create mode 100644 board/samsung/odroid/Makefile create mode 100644 board/samsung/odroid/odroid.c create mode 100644 board/samsung/odroid/setup.h (limited to 'board') diff --git a/board/samsung/odroid/Makefile b/board/samsung/odroid/Makefile new file mode 100644 index 0000000000..b98aaeb101 --- /dev/null +++ b/board/samsung/odroid/Makefile @@ -0,0 +1,8 @@ +# +# Copyright (c) 2014 Samsung Electronics Co., Ltd. All rights reserved. +# Przemyslaw Marczak +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y := odroid.o diff --git a/board/samsung/odroid/odroid.c b/board/samsung/odroid/odroid.c new file mode 100644 index 0000000000..ac19527a90 --- /dev/null +++ b/board/samsung/odroid/odroid.c @@ -0,0 +1,470 @@ +/* + * Copyright (C) 2014 Samsung Electronics + * Przemyslaw Marczak + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include "setup.h" + +DECLARE_GLOBAL_DATA_PTR; + +#ifdef CONFIG_BOARD_TYPES +/* Odroid board types */ +enum { + ODROID_TYPE_U3, + ODROID_TYPE_X2, + ODROID_TYPES, +}; + +void set_board_type(void) +{ + /* Set GPA1 pin 1 to HI - enable XCL205 output */ + writel(XCL205_EN_GPIO_CON_CFG, XCL205_EN_GPIO_CON); + writel(XCL205_EN_GPIO_DAT_CFG, XCL205_EN_GPIO_CON + 0x4); + writel(XCL205_EN_GPIO_PUD_CFG, XCL205_EN_GPIO_CON + 0x8); + writel(XCL205_EN_GPIO_DRV_CFG, XCL205_EN_GPIO_CON + 0xc); + + /* Set GPC1 pin 2 to IN - check XCL205 output state */ + writel(XCL205_STATE_GPIO_CON_CFG, XCL205_STATE_GPIO_CON); + writel(XCL205_STATE_GPIO_PUD_CFG, XCL205_STATE_GPIO_CON + 0x8); + + /* XCL205 - needs some latch time */ + sdelay(200000); + + /* Check GPC1 pin2 - LED supplied by XCL205 - X2 only */ + if (readl(XCL205_STATE_GPIO_DAT) & (1 << XCL205_STATE_GPIO_PIN)) + gd->board_type = ODROID_TYPE_X2; + else + gd->board_type = ODROID_TYPE_U3; +} + +const char *get_board_type(void) +{ + const char *board_type[] = {"u3", "x2"}; + + return board_type[gd->board_type]; +} +#endif + +#ifdef CONFIG_SET_DFU_ALT_INFO +char *get_dfu_alt_system(void) +{ + return getenv("dfu_alt_system"); +} + +char *get_dfu_alt_boot(void) +{ + char *alt_boot; + + switch (get_boot_mode()) { + case BOOT_MODE_SD: + alt_boot = CONFIG_DFU_ALT_BOOT_SD; + break; + case BOOT_MODE_EMMC: + case BOOT_MODE_EMMC_SD: + alt_boot = CONFIG_DFU_ALT_BOOT_EMMC; + break; + default: + alt_boot = NULL; + break; + } + return alt_boot; +} +#endif + +static void board_clock_init(void) +{ + unsigned int set, clr, clr_src_cpu, clr_pll_con0, clr_src_dmc; + struct exynos4x12_clock *clk = (struct exynos4x12_clock *) + samsung_get_base_clock(); + + /* + * CMU_CPU clocks src to MPLL + * Bit values: 0 ; 1 + * MUX_APLL_SEL: FIN_PLL ; FOUT_APLL + * MUX_CORE_SEL: MOUT_APLL ; SCLK_MPLL + * MUX_HPM_SEL: MOUT_APLL ; SCLK_MPLL_USER_C + * MUX_MPLL_USER_SEL_C: FIN_PLL ; SCLK_MPLL + */ + clr_src_cpu = MUX_APLL_SEL(1) | MUX_CORE_SEL(1) | + MUX_HPM_SEL(1) | MUX_MPLL_USER_SEL_C(1); + set = MUX_APLL_SEL(0) | MUX_CORE_SEL(1) | MUX_HPM_SEL(1) | + MUX_MPLL_USER_SEL_C(1); + + clrsetbits_le32(&clk->src_cpu, clr_src_cpu, set); + + /* Wait for mux change */ + while (readl(&clk->mux_stat_cpu) & MUX_STAT_CPU_CHANGING) + continue; + + /* Set APLL to 1000MHz */ + clr_pll_con0 = SDIV(7) | PDIV(63) | MDIV(1023) | FSEL(1); + set = SDIV(0) | PDIV(3) | MDIV(125) | FSEL(1); + + clrsetbits_le32(&clk->apll_con0, clr_pll_con0, set); + + /* Wait for PLL to be locked */ + while (!(readl(&clk->apll_con0) & PLL_LOCKED_BIT)) + continue; + + /* Set CMU_CPU clocks src to APLL */ + set = MUX_APLL_SEL(1) | MUX_CORE_SEL(0) | MUX_HPM_SEL(0) | + MUX_MPLL_USER_SEL_C(1); + clrsetbits_le32(&clk->src_cpu, clr_src_cpu, set); + + /* Wait for mux change */ + while (readl(&clk->mux_stat_cpu) & MUX_STAT_CPU_CHANGING) + continue; + + set = CORE_RATIO(0) | COREM0_RATIO(2) | COREM1_RATIO(5) | + PERIPH_RATIO(0) | ATB_RATIO(4) | PCLK_DBG_RATIO(1) | + APLL_RATIO(0) | CORE2_RATIO(0); + /* + * Set dividers for MOUTcore = 1000 MHz + * coreout = MOUT / (ratio + 1) = 1000 MHz (0) + * corem0 = armclk / (ratio + 1) = 333 MHz (2) + * corem1 = armclk / (ratio + 1) = 166 MHz (5) + * periph = armclk / (ratio + 1) = 1000 MHz (0) + * atbout = MOUT / (ratio + 1) = 200 MHz (4) + * pclkdbgout = atbout / (ratio + 1) = 100 MHz (1) + * sclkapll = MOUTapll / (ratio + 1) = 1000 MHz (0) + * core2out = core_out / (ratio + 1) = 1000 MHz (0) (armclk) + */ + clr = CORE_RATIO(7) | COREM0_RATIO(7) | COREM1_RATIO(7) | + PERIPH_RATIO(7) | ATB_RATIO(7) | PCLK_DBG_RATIO(7) | + APLL_RATIO(7) | CORE2_RATIO(7); + + clrsetbits_le32(&clk->div_cpu0, clr, set); + + /* Wait for divider ready status */ + while (readl(&clk->div_stat_cpu0) & DIV_STAT_CPU0_CHANGING) + continue; + + /* + * For MOUThpm = 1000 MHz (MOUTapll) + * doutcopy = MOUThpm / (ratio + 1) = 200 (4) + * sclkhpm = doutcopy / (ratio + 1) = 200 (4) + * cores_out = armclk / (ratio + 1) = 1000 (0) + */ + clr = COPY_RATIO(7) | HPM_RATIO(7) | CORES_RATIO(7); + set = COPY_RATIO(4) | HPM_RATIO(4) | CORES_RATIO(0); + + clrsetbits_le32(&clk->div_cpu1, clr, set); + + /* Wait for divider ready status */ + while (readl(&clk->div_stat_cpu1) & DIV_STAT_CPU1_CHANGING) + continue; + + /* + * Set CMU_DMC clocks src to APLL + * Bit values: 0 ; 1 + * MUX_C2C_SEL: SCLKMPLL ; SCLKAPLL + * MUX_DMC_BUS_SEL: SCLKMPLL ; SCLKAPLL + * MUX_DPHY_SEL: SCLKMPLL ; SCLKAPLL + * MUX_MPLL_SEL: FINPLL ; MOUT_MPLL_FOUT + * MUX_PWI_SEL: 0110 (MPLL); 0111 (EPLL); 1000 (VPLL); 0(XXTI) + * MUX_G2D_ACP0_SEL: SCLKMPLL ; SCLKAPLL + * MUX_G2D_ACP1_SEL: SCLKEPLL ; SCLKVPLL + * MUX_G2D_ACP_SEL: OUT_ACP0 ; OUT_ACP1 + */ + clr_src_dmc = MUX_C2C_SEL(1) | MUX_DMC_BUS_SEL(1) | + MUX_DPHY_SEL(1) | MUX_MPLL_SEL(1) | + MUX_PWI_SEL(15) | MUX_G2D_ACP0_SEL(1) | + MUX_G2D_ACP1_SEL(1) | MUX_G2D_ACP_SEL(1); + set = MUX_C2C_SEL(1) | MUX_DMC_BUS_SEL(1) | MUX_DPHY_SEL(1) | + MUX_MPLL_SEL(0) | MUX_PWI_SEL(0) | MUX_G2D_ACP0_SEL(1) | + MUX_G2D_ACP1_SEL(1) | MUX_G2D_ACP_SEL(1); + + clrsetbits_le32(&clk->src_dmc, clr_src_dmc, set); + + /* Wait for mux change */ + while (readl(&clk->mux_stat_dmc) & MUX_STAT_DMC_CHANGING) + continue; + + /* Set MPLL to 800MHz */ + set = SDIV(0) | PDIV(3) | MDIV(100) | FSEL(0) | PLL_ENABLE(1); + + clrsetbits_le32(&clk->mpll_con0, clr_pll_con0, set); + + /* Wait for PLL to be locked */ + while (!(readl(&clk->mpll_con0) & PLL_LOCKED_BIT)) + continue; + + /* Switch back CMU_DMC mux */ + set = MUX_C2C_SEL(0) | MUX_DMC_BUS_SEL(0) | MUX_DPHY_SEL(0) | + MUX_MPLL_SEL(1) | MUX_PWI_SEL(8) | MUX_G2D_ACP0_SEL(0) | + MUX_G2D_ACP1_SEL(0) | MUX_G2D_ACP_SEL(0); + + clrsetbits_le32(&clk->src_dmc, clr_src_dmc, set); + + /* Wait for mux change */ + while (readl(&clk->mux_stat_dmc) & MUX_STAT_DMC_CHANGING) + continue; + + /* CLK_DIV_DMC0 */ + clr = ACP_RATIO(7) | ACP_PCLK_RATIO(7) | DPHY_RATIO(7) | + DMC_RATIO(7) | DMCD_RATIO(7) | DMCP_RATIO(7); + /* + * For: + * MOUTdmc = 800 MHz + * MOUTdphy = 800 MHz + * + * aclk_acp = MOUTdmc / (ratio + 1) = 200 (3) + * pclk_acp = aclk_acp / (ratio + 1) = 100 (1) + * sclk_dphy = MOUTdphy / (ratio + 1) = 400 (1) + * sclk_dmc = MOUTdmc / (ratio + 1) = 400 (1) + * aclk_dmcd = sclk_dmc / (ratio + 1) = 200 (1) + * aclk_dmcp = aclk_dmcd / (ratio + 1) = 100 (1) + */ + set = ACP_RATIO(3) | ACP_PCLK_RATIO(1) | DPHY_RATIO(1) | + DMC_RATIO(1) | DMCD_RATIO(1) | DMCP_RATIO(1); + + clrsetbits_le32(&clk->div_dmc0, clr, set); + + /* Wait for divider ready status */ + while (readl(&clk->div_stat_dmc0) & DIV_STAT_DMC0_CHANGING) + continue; + + /* CLK_DIV_DMC1 */ + clr = G2D_ACP_RATIO(15) | C2C_RATIO(7) | PWI_RATIO(15) | + C2C_ACLK_RATIO(7) | DVSEM_RATIO(127) | DPM_RATIO(127); + /* + * For: + * MOUTg2d = 800 MHz + * MOUTc2c = 800 Mhz + * MOUTpwi = 108 MHz + * + * sclk_g2d_acp = MOUTg2d / (ratio + 1) = 400 (1) + * sclk_c2c = MOUTc2c / (ratio + 1) = 400 (1) + * aclk_c2c = sclk_c2c / (ratio + 1) = 200 (1) + * sclk_pwi = MOUTpwi / (ratio + 1) = 18 (5) + */ + set = G2D_ACP_RATIO(1) | C2C_RATIO(1) | PWI_RATIO(5) | + C2C_ACLK_RATIO(1) | DVSEM_RATIO(1) | DPM_RATIO(1); + + clrsetbits_le32(&clk->div_dmc1, clr, set); + + /* Wait for divider ready status */ + while (readl(&clk->div_stat_dmc1) & DIV_STAT_DMC1_CHANGING) + continue; + + /* CLK_SRC_PERIL0 */ + clr = UART0_SEL(15) | UART1_SEL(15) | UART2_SEL(15) | + UART3_SEL(15) | UART4_SEL(15); + /* + * Set CLK_SRC_PERIL0 clocks src to MPLL + * src values: 0(XXTI); 1(XusbXTI); 2(SCLK_HDMI24M); 3(SCLK_USBPHY0); + * 5(SCLK_HDMIPHY); 6(SCLK_MPLL_USER_T); 7(SCLK_EPLL); + * 8(SCLK_VPLL) + * + * Set all to SCLK_MPLL_USER_T + */ + set = UART0_SEL(6) | UART1_SEL(6) | UART2_SEL(6) | UART3_SEL(6) | + UART4_SEL(6); + + clrsetbits_le32(&clk->src_peril0, clr, set); + + /* CLK_DIV_PERIL0 */ + clr = UART0_RATIO(15) | UART1_RATIO(15) | UART2_RATIO(15) | + UART3_RATIO(15) | UART4_RATIO(15); + /* + * For MOUTuart0-4: 800MHz + * + * SCLK_UARTx = MOUTuartX / (ratio + 1) = 100 (7) + */ + set = UART0_RATIO(7) | UART1_RATIO(7) | UART2_RATIO(7) | + UART3_RATIO(7) | UART4_RATIO(7); + + clrsetbits_le32(&clk->div_peril0, clr, set); + + while (readl(&clk->div_stat_peril0) & DIV_STAT_PERIL0_CHANGING) + continue; + + /* CLK_DIV_FSYS1 */ + clr = MMC0_RATIO(15) | MMC0_PRE_RATIO(255) | MMC1_RATIO(15) | + MMC1_PRE_RATIO(255); + /* + * For MOUTmmc0-3 = 800 MHz (MPLL) + * + * DOUTmmc1 = MOUTmmc1 / (ratio + 1) = 100 (7) + * sclk_mmc1 = DOUTmmc1 / (ratio + 1) = 50 (1) + * DOUTmmc0 = MOUTmmc0 / (ratio + 1) = 100 (7) + * sclk_mmc0 = DOUTmmc0 / (ratio + 1) = 50 (1) + */ + set = MMC0_RATIO(7) | MMC0_PRE_RATIO(1) | MMC1_RATIO(7) | + MMC1_PRE_RATIO(1); + + clrsetbits_le32(&clk->div_fsys1, clr, set); + + /* Wait for divider ready status */ + while (readl(&clk->div_stat_fsys1) & DIV_STAT_FSYS1_CHANGING) + continue; + + /* CLK_DIV_FSYS2 */ + clr = MMC2_RATIO(15) | MMC2_PRE_RATIO(255) | MMC3_RATIO(15) | + MMC3_PRE_RATIO(255); + /* + * For MOUTmmc0-3 = 800 MHz (MPLL) + * + * DOUTmmc3 = MOUTmmc3 / (ratio + 1) = 100 (7) + * sclk_mmc3 = DOUTmmc3 / (ratio + 1) = 50 (1) + * DOUTmmc2 = MOUTmmc2 / (ratio + 1) = 100 (7) + * sclk_mmc2 = DOUTmmc2 / (ratio + 1) = 50 (1) + */ + set = MMC2_RATIO(7) | MMC2_PRE_RATIO(1) | MMC3_RATIO(7) | + MMC3_PRE_RATIO(1); + + clrsetbits_le32(&clk->div_fsys2, clr, set); + + /* Wait for divider ready status */ + while (readl(&clk->div_stat_fsys2) & DIV_STAT_FSYS2_CHANGING) + continue; + + /* CLK_DIV_FSYS3 */ + clr = MMC4_RATIO(15) | MMC4_PRE_RATIO(255); + /* + * For MOUTmmc4 = 800 MHz (MPLL) + * + * DOUTmmc4 = MOUTmmc4 / (ratio + 1) = 100 (7) + * sclk_mmc4 = DOUTmmc4 / (ratio + 1) = 100 (0) + */ + set = MMC4_RATIO(7) | MMC4_PRE_RATIO(0); + + clrsetbits_le32(&clk->div_fsys3, clr, set); + + /* Wait for divider ready status */ + while (readl(&clk->div_stat_fsys3) & DIV_STAT_FSYS3_CHANGING) + continue; + + return; +} + +static void board_gpio_init(void) +{ + /* eMMC Reset Pin */ + gpio_cfg_pin(EXYNOS4X12_GPIO_K12, S5P_GPIO_FUNC(0x1)); + gpio_set_pull(EXYNOS4X12_GPIO_K12, S5P_GPIO_PULL_NONE); + gpio_set_drv(EXYNOS4X12_GPIO_K12, S5P_GPIO_DRV_4X); + + /* Enable FAN (Odroid U3) */ + gpio_set_pull(EXYNOS4X12_GPIO_D00, S5P_GPIO_PULL_UP); + gpio_set_drv(EXYNOS4X12_GPIO_D00, S5P_GPIO_DRV_4X); + gpio_direction_output(EXYNOS4X12_GPIO_D00, 1); + + /* OTG Vbus output (Odroid U3+) */ + gpio_set_pull(EXYNOS4X12_GPIO_L20, S5P_GPIO_PULL_NONE); + gpio_set_drv(EXYNOS4X12_GPIO_L20, S5P_GPIO_DRV_4X); + gpio_direction_output(EXYNOS4X12_GPIO_L20, 0); + + /* OTG INT (Odroid U3+) */ + gpio_set_pull(EXYNOS4X12_GPIO_X31, S5P_GPIO_PULL_UP); + gpio_set_drv(EXYNOS4X12_GPIO_X31, S5P_GPIO_DRV_4X); + gpio_direction_input(EXYNOS4X12_GPIO_X31); +} + +static int pmic_init_max77686(void) +{ + struct pmic *p = pmic_get("MAX77686_PMIC"); + + if (pmic_probe(p)) + return -ENODEV; + + /* Set LDO Voltage */ + max77686_set_ldo_voltage(p, 20, 1800000); /* LDO20 eMMC */ + max77686_set_ldo_voltage(p, 21, 2800000); /* LDO21 SD */ + max77686_set_ldo_voltage(p, 22, 2800000); /* LDO22 eMMC */ + + return 0; +} + +#ifdef CONFIG_SYS_I2C_INIT_BOARD +static void board_init_i2c(void) +{ + /* I2C_0 */ + if (exynos_pinmux_config(PERIPH_ID_I2C0, PINMUX_FLAG_NONE)) + debug("I2C%d not configured\n", (I2C_0)); +} +#endif + +int exynos_early_init_f(void) +{ + board_clock_init(); + board_gpio_init(); + + return 0; +} + +int exynos_init(void) +{ + /* The last MB of memory is reserved for secure firmware */ + gd->ram_size -= SZ_1M; + gd->bd->bi_dram[CONFIG_NR_DRAM_BANKS - 1].size -= SZ_1M; + + return 0; +} + +int exynos_power_init(void) +{ +#ifdef CONFIG_SYS_I2C_INIT_BOARD + board_init_i2c(); +#endif + pmic_init(I2C_0); + pmic_init_max77686(); + + return 0; +} + +#ifdef CONFIG_USB_GADGET +static int s5pc210_phy_control(int on) +{ + struct pmic *p_pmic; + + p_pmic = pmic_get("MAX77686_PMIC"); + if (!p_pmic) + return -ENODEV; + + if (pmic_probe(p_pmic)) + return -1; + + if (on) + return max77686_set_ldo_mode(p_pmic, 12, OPMODE_ON); + else + return max77686_set_ldo_mode(p_pmic, 12, OPMODE_LPM); +} + +struct s3c_plat_otg_data s5pc210_otg_data = { + .phy_control = s5pc210_phy_control, + .regs_phy = EXYNOS4X12_USBPHY_BASE, + .regs_otg = EXYNOS4X12_USBOTG_BASE, + .usb_phy_ctrl = EXYNOS4X12_USBPHY_CONTROL, + .usb_flags = PHY0_SLEEP, +}; + +int board_usb_init(int index, enum usb_init_type init) +{ + debug("USB_udc_probe\n"); + return s3c_udc_probe(&s5pc210_otg_data); +} +#endif + +void reset_misc(void) +{ + /* Reset eMMC*/ + gpio_set_value(EXYNOS4X12_GPIO_K12, 0); + mdelay(10); + gpio_set_value(EXYNOS4X12_GPIO_K12, 1); +} diff --git a/board/samsung/odroid/setup.h b/board/samsung/odroid/setup.h new file mode 100644 index 0000000000..3e48dada27 --- /dev/null +++ b/board/samsung/odroid/setup.h @@ -0,0 +1,255 @@ +/* + * Copyright (C) 2014 Samsung Electronics + * Przemyslaw Marczak + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __ODROIDU3_SETUP__ +#define __ODROIDU3_SETUP__ + +/* A/M PLL_CON0 */ +#define SDIV(x) ((x) & 0x7) +#define PDIV(x) (((x) & 0x3f) << 8) +#define MDIV(x) (((x) & 0x3ff) << 16) +#define FSEL(x) (((x) & 0x1) << 27) +#define PLL_LOCKED_BIT (0x1 << 29) +#define PLL_ENABLE(x) (((x) & 0x1) << 31) + +/* CLK_SRC_CPU */ +#define MUX_APLL_SEL(x) ((x) & 0x1) +#define MUX_CORE_SEL(x) (((x) & 0x1) << 16) +#define MUX_HPM_SEL(x) (((x) & 0x1) << 20) +#define MUX_MPLL_USER_SEL_C(x) (((x) & 0x1) << 24) + +#define MUX_STAT_CHANGING 0x100 + +/* CLK_MUX_STAT_CPU */ +#define APLL_SEL(x) ((x) & 0x7) +#define CORE_SEL(x) (((x) & 0x7) << 16) +#define HPM_SEL(x) (((x) & 0x7) << 20) +#define MPLL_USER_SEL_C(x) (((x) & 0x7) << 24) +#define MUX_STAT_CPU_CHANGING (APLL_SEL(MUX_STAT_CHANGING) | \ + CORE_SEL(MUX_STAT_CHANGING) | \ + HPM_SEL(MUX_STAT_CHANGING) | \ + MPLL_USER_SEL_C(MUX_STAT_CHANGING)) + +/* CLK_DIV_CPU0 */ +#define CORE_RATIO(x) ((x) & 0x7) +#define COREM0_RATIO(x) (((x) & 0x7) << 4) +#define COREM1_RATIO(x) (((x) & 0x7) << 8) +#define PERIPH_RATIO(x) (((x) & 0x7) << 12) +#define ATB_RATIO(x) (((x) & 0x7) << 16) +#define PCLK_DBG_RATIO(x) (((x) & 0x7) << 20) +#define APLL_RATIO(x) (((x) & 0x7) << 24) +#define CORE2_RATIO(x) (((x) & 0x7) << 28) + +/* CLK_DIV_STAT_CPU0 */ +#define DIV_CORE(x) ((x) & 0x1) +#define DIV_COREM0(x) (((x) & 0x1) << 4) +#define DIV_COREM1(x) (((x) & 0x1) << 8) +#define DIV_PERIPH(x) (((x) & 0x1) << 12) +#define DIV_ATB(x) (((x) & 0x1) << 16) +#define DIV_PCLK_DBG(x) (((x) & 0x1) << 20) +#define DIV_APLL(x) (((x) & 0x1) << 24) +#define DIV_CORE2(x) (((x) & 0x1) << 28) + +#define DIV_STAT_CHANGING 0x1 +#define DIV_STAT_CPU0_CHANGING (DIV_CORE(DIV_STAT_CHANGING) | \ + DIV_COREM0(DIV_STAT_CHANGING) | \ + DIV_COREM1(DIV_STAT_CHANGING) | \ + DIV_PERIPH(DIV_STAT_CHANGING) | \ + DIV_ATB(DIV_STAT_CHANGING) | \ + DIV_PCLK_DBG(DIV_STAT_CHANGING) | \ + DIV_APLL(DIV_STAT_CHANGING) | \ + DIV_CORE2(DIV_STAT_CHANGING)) + +/* CLK_DIV_CPU1 */ +#define COPY_RATIO(x) ((x) & 0x7) +#define HPM_RATIO(x) (((x) & 0x7) << 4) +#define CORES_RATIO(x) (((x) & 0x7) << 8) + +/* CLK_DIV_STAT_CPU1 */ +#define DIV_COPY(x) ((x) & 0x7) +#define DIV_HPM(x) (((x) & 0x1) << 4) +#define DIV_CORES(x) (((x) & 0x1) << 8) + +#define DIV_STAT_CPU1_CHANGING (DIV_COPY(DIV_STAT_CHANGING) | \ + DIV_HPM(DIV_STAT_CHANGING) | \ + DIV_CORES(DIV_STAT_CHANGING)) + +/* CLK_SRC_DMC */ +#define MUX_C2C_SEL(x) ((x) & 0x1) +#define MUX_DMC_BUS_SEL(x) (((x) & 0x1) << 4) +#define MUX_DPHY_SEL(x) (((x) & 0x1) << 8) +#define MUX_MPLL_SEL(x) (((x) & 0x1) << 12) +#define MUX_PWI_SEL(x) (((x) & 0xf) << 16) +#define MUX_G2D_ACP0_SEL(x) (((x) & 0x1) << 20) +#define MUX_G2D_ACP1_SEL(x) (((x) & 0x1) << 24) +#define MUX_G2D_ACP_SEL(x) (((x) & 0x1) << 28) + +/* CLK_MUX_STAT_DMC */ +#define C2C_SEL(x) (((x)) & 0x7) +#define DMC_BUS_SEL(x) (((x) & 0x7) << 4) +#define DPHY_SEL(x) (((x) & 0x7) << 8) +#define MPLL_SEL(x) (((x) & 0x7) << 12) +/* #define PWI_SEL(x) (((x) & 0xf) << 16) - Reserved */ +#define G2D_ACP0_SEL(x) (((x) & 0x7) << 20) +#define G2D_ACP1_SEL(x) (((x) & 0x7) << 24) +#define G2D_ACP_SEL(x) (((x) & 0x7) << 28) + +#define MUX_STAT_DMC_CHANGING (C2C_SEL(MUX_STAT_CHANGING) | \ + DMC_BUS_SEL(MUX_STAT_CHANGING) | \ + DPHY_SEL(MUX_STAT_CHANGING) | \ + MPLL_SEL(MUX_STAT_CHANGING) |\ + G2D_ACP0_SEL(MUX_STAT_CHANGING) | \ + G2D_ACP1_SEL(MUX_STAT_CHANGING) | \ + G2D_ACP_SEL(MUX_STAT_CHANGING)) + +/* CLK_DIV_DMC0 */ +#define ACP_RATIO(x) ((x) & 0x7) +#define ACP_PCLK_RATIO(x) (((x) & 0x7) << 4) +#define DPHY_RATIO(x) (((x) & 0x7) << 8) +#define DMC_RATIO(x) (((x) & 0x7) << 12) +#define DMCD_RATIO(x) (((x) & 0x7) << 16) +#define DMCP_RATIO(x) (((x) & 0x7) << 20) + +/* CLK_DIV_STAT_DMC0 */ +#define DIV_ACP(x) ((x) & 0x1) +#define DIV_ACP_PCLK(x) (((x) & 0x1) << 4) +#define DIV_DPHY(x) (((x) & 0x1) << 8) +#define DIV_DMC(x) (((x) & 0x1) << 12) +#define DIV_DMCD(x) (((x) & 0x1) << 16) +#define DIV_DMCP(x) (((x) & 0x1) << 20) + +#define DIV_STAT_DMC0_CHANGING (DIV_ACP(DIV_STAT_CHANGING) | \ + DIV_ACP_PCLK(DIV_STAT_CHANGING) | \ + DIV_DPHY(DIV_STAT_CHANGING) | \ + DIV_DMC(DIV_STAT_CHANGING) | \ + DIV_DMCD(DIV_STAT_CHANGING) | \ + DIV_DMCP(DIV_STAT_CHANGING)) + +/* CLK_DIV_DMC1 */ +#define G2D_ACP_RATIO(x) ((x) & 0xf) +#define C2C_RATIO(x) (((x) & 0x7) << 4) +#define PWI_RATIO(x) (((x) & 0xf) << 8) +#define C2C_ACLK_RATIO(x) (((x) & 0x7) << 12) +#define DVSEM_RATIO(x) (((x) & 0x7f) << 16) +#define DPM_RATIO(x) (((x) & 0x7f) << 24) + +/* CLK_DIV_STAT_DMC1 */ +#define DIV_G2D_ACP(x) ((x) & 0x1) +#define DIV_C2C(x) (((x) & 0x1) << 4) +#define DIV_PWI(x) (((x) & 0x1) << 8) +#define DIV_C2C_ACLK(x) (((x) & 0x1) << 12) +#define DIV_DVSEM(x) (((x) & 0x1) << 16) +#define DIV_DPM(x) (((x) & 0x1) << 24) + +#define DIV_STAT_DMC1_CHANGING (DIV_G2D_ACP(DIV_STAT_CHANGING) | \ + DIV_C2C(DIV_STAT_CHANGING) | \ + DIV_PWI(DIV_STAT_CHANGING) | \ + DIV_C2C_ACLK(DIV_STAT_CHANGING) | \ + DIV_DVSEM(DIV_STAT_CHANGING) | \ + DIV_DPM(DIV_STAT_CHANGING)) + +/* Set CLK_SRC_PERIL0 */ +#define UART4_SEL(x) (((x) & 0xf) << 16) +#define UART3_SEL(x) (((x) & 0xf) << 12) +#define UART2_SEL(x) (((x) & 0xf) << 8) +#define UART1_SEL(x) (((x) & 0xf) << 4) +#define UART0_SEL(x) ((x) & 0xf) + +/* Set CLK_DIV_PERIL0 */ +#define UART4_RATIO(x) (((x) & 0xf) << 16) +#define UART3_RATIO(x) (((x) & 0xf) << 12) +#define UART2_RATIO(x) (((x) & 0xf) << 8) +#define UART1_RATIO(x) (((x) & 0xf) << 4) +#define UART0_RATIO(x) ((x) & 0xf) + +/* Set CLK_DIV_STAT_PERIL0 */ +#define DIV_UART4(x) (((x) & 0x1) << 16) +#define DIV_UART3(x) (((x) & 0x1) << 12) +#define DIV_UART2(x) (((x) & 0x1) << 8) +#define DIV_UART1(x) (((x) & 0x1) << 4) +#define DIV_UART0(x) ((x) & 0x1) + +#define DIV_STAT_PERIL0_CHANGING (DIV_UART4(DIV_STAT_CHANGING) | \ + DIV_UART3(DIV_STAT_CHANGING) | \ + DIV_UART2(DIV_STAT_CHANGING) | \ + DIV_UART1(DIV_STAT_CHANGING) | \ + DIV_UART0(DIV_STAT_CHANGING)) + +/* CLK_DIV_FSYS1 */ +#define MMC0_RATIO(x) ((x) & 0xf) +#define MMC0_PRE_RATIO(x) (((x) & 0xff) << 8) +#define MMC1_RATIO(x) (((x) & 0xf) << 16) +#define MMC1_PRE_RATIO(x) (((x) & 0xff) << 24) + +/* CLK_DIV_STAT_FSYS1 */ +#define DIV_MMC0(x) ((x) & 1) +#define DIV_MMC0_PRE(x) (((x) & 1) << 8) +#define DIV_MMC1(x) (((x) & 1) << 16) +#define DIV_MMC1_PRE(x) (((x) & 1) << 24) + +#define DIV_STAT_FSYS1_CHANGING (DIV_MMC0(DIV_STAT_CHANGING) | \ + DIV_MMC0_PRE(DIV_STAT_CHANGING) | \ + DIV_MMC1(DIV_STAT_CHANGING) | \ + DIV_MMC1_PRE(DIV_STAT_CHANGING)) + +/* CLK_DIV_FSYS2 */ +#define MMC2_RATIO(x) ((x) & 0xf) +#define MMC2_PRE_RATIO(x) (((x) & 0xff) << 8) +#define MMC3_RATIO(x) (((x) & 0xf) << 16) +#define MMC3_PRE_RATIO(x) (((x) & 0xff) << 24) + +/* CLK_DIV_STAT_FSYS2 */ +#define DIV_MMC2(x) ((x) & 0x1) +#define DIV_MMC2_PRE(x) (((x) & 0x1) << 8) +#define DIV_MMC3(x) (((x) & 0x1) << 16) +#define DIV_MMC3_PRE(x) (((x) & 0x1) << 24) + +#define DIV_STAT_FSYS2_CHANGING (DIV_MMC2(DIV_STAT_CHANGING) | \ + DIV_MMC2_PRE(DIV_STAT_CHANGING) | \ + DIV_MMC3(DIV_STAT_CHANGING) | \ + DIV_MMC3_PRE(DIV_STAT_CHANGING)) + +/* CLK_DIV_FSYS3 */ +#define MMC4_RATIO(x) ((x) & 0x7) +#define MMC4_PRE_RATIO(x) (((x) & 0xff) << 8) + +/* CLK_DIV_STAT_FSYS3 */ +#define DIV_MMC4(x) ((x) & 0x1) +#define DIV_MMC4_PRE(x) (((x) & 0x1) << 8) + +#define DIV_STAT_FSYS3_CHANGING (DIV_MMC4(DIV_STAT_CHANGING) | \ + DIV_MMC4_PRE(DIV_STAT_CHANGING)) + +/* XCL205 GPIO config - Odroid U3 */ +#define XCL205_GPIO_BASE EXYNOS4X12_GPIO_PART1_BASE +#define XCL205_EN_GPIO_OFFSET 0x20 /* GPA1 */ +#define XCL205_EN_GPIO_PIN 1 +#define XCL205_EN_GPIO_CON (XCL205_GPIO_BASE + \ + XCL205_EN_GPIO_OFFSET) +#define XCL205_EN_GPIO_CON_CFG (S5P_GPIO_OUTPUT << \ + 4 * XCL205_EN_GPIO_PIN) +#define XCL205_EN_GPIO_DAT_CFG (0x1 << XCL205_EN_GPIO_PIN) +#define XCL205_EN_GPIO_PUD_CFG (S5P_GPIO_PULL_UP << \ + 2 * XCL205_EN_GPIO_PIN) +#define XCL205_EN_GPIO_DRV_CFG (S5P_GPIO_DRV_4X << \ + 2 * XCL205_EN_GPIO_PIN) + +#define XCL205_STATE_GPIO_OFFSET 0x80 /* GPC1 */ +#define XCL205_STATE_GPIO_PIN 2 +#define XCL205_STATE_GPIO_CON (XCL205_GPIO_BASE + \ + XCL205_STATE_GPIO_OFFSET) +#define XCL205_STATE_GPIO_DAT XCL205_STATE_GPIO_CON + 0x4 +#define XCL205_STATE_GPIO_CON_CFG (S5P_GPIO_INPUT << \ + 4 * XCL205_STATE_GPIO_PIN) +#define XCL205_STATE_GPIO_PUD_CFG (S5P_GPIO_PULL_NONE << \ + 2 * XCL205_STATE_GPIO_PIN) + +#ifdef CONFIG_BOARD_TYPES +extern void sdelay(unsigned long); +#endif + +#endif /*__ODROIDU3_SETUP__ */ -- cgit From 73eca21128de78f2ebe172a4a9348057ce2a7534 Mon Sep 17 00:00:00 2001 From: Przemyslaw Marczak Date: Mon, 1 Sep 2014 13:50:53 +0200 Subject: odroid: kconfig: add odroid_defconfig This config is valid for two devices: - Odroid X2, - Odroid U3. Signed-off-by: Przemyslaw Marczak Cc: Minkyu Kang Cc: Tom Rini Signed-off-by: Minkyu Kang --- board/samsung/odroid/Kconfig | 15 +++++++++++++++ board/samsung/odroid/MAINTAINERS | 6 ++++++ 2 files changed, 21 insertions(+) create mode 100644 board/samsung/odroid/Kconfig create mode 100644 board/samsung/odroid/MAINTAINERS (limited to 'board') diff --git a/board/samsung/odroid/Kconfig b/board/samsung/odroid/Kconfig new file mode 100644 index 0000000000..8dcfb4808d --- /dev/null +++ b/board/samsung/odroid/Kconfig @@ -0,0 +1,15 @@ +if TARGET_ODROID + +config SYS_BOARD + string + default "odroid" + +config SYS_VENDOR + string + default "samsung" + +config SYS_CONFIG_NAME + string + default "odroid" + +endif diff --git a/board/samsung/odroid/MAINTAINERS b/board/samsung/odroid/MAINTAINERS new file mode 100644 index 0000000000..2131d365ce --- /dev/null +++ b/board/samsung/odroid/MAINTAINERS @@ -0,0 +1,6 @@ +ODROID BOARD +M: Przemyslaw Marczak +S: Maintained +F: board/samsung/odroid/ +F: include/configs/odroid.h +F: configs/odroid_defconfig -- cgit From fd97fe251c9fc6f7af374a161a47f49df6caad52 Mon Sep 17 00:00:00 2001 From: Masahiro Yamada Date: Mon, 4 Aug 2014 10:13:35 +0900 Subject: MAINTAINERS: update the maintainer of Arndale board Inderpal's email address is not working any more. Chander will be a new maintainer. Signed-off-by: Masahiro Yamada Cc: Chander Kashyap Cc: Minkyu Kang Signed-off-by: Minkyu Kang --- board/samsung/arndale/MAINTAINERS | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'board') diff --git a/board/samsung/arndale/MAINTAINERS b/board/samsung/arndale/MAINTAINERS index 0a01a076a3..7dc17854d1 100644 --- a/board/samsung/arndale/MAINTAINERS +++ b/board/samsung/arndale/MAINTAINERS @@ -1,5 +1,5 @@ ARNDALE BOARD -M: Inderpal Singh +M: Chander Kashyap S: Maintained F: board/samsung/arndale/ F: include/configs/arndale.h -- cgit From b09200639d4c052e2bdf0df6fe843b7a8bcf01cc Mon Sep 17 00:00:00 2001 From: Przemyslaw Marczak Date: Thu, 24 Jul 2014 12:42:01 +0200 Subject: odroid: set MPLL clock to 880MHz This patch changes MPLL from 800MHz to 880MHz on Odroid. Signed-off-by: Przemyslaw Marczak Signed-off-by: Minkyu Kang --- board/samsung/odroid/odroid.c | 60 +++++++++++++++++++++---------------------- 1 file changed, 30 insertions(+), 30 deletions(-) (limited to 'board') diff --git a/board/samsung/odroid/odroid.c b/board/samsung/odroid/odroid.c index ac19527a90..fd5d2d2ca9 100644 --- a/board/samsung/odroid/odroid.c +++ b/board/samsung/odroid/odroid.c @@ -195,8 +195,8 @@ static void board_clock_init(void) while (readl(&clk->mux_stat_dmc) & MUX_STAT_DMC_CHANGING) continue; - /* Set MPLL to 800MHz */ - set = SDIV(0) | PDIV(3) | MDIV(100) | FSEL(0) | PLL_ENABLE(1); + /* Set MPLL to 880MHz */ + set = SDIV(0) | PDIV(3) | MDIV(110) | FSEL(0) | PLL_ENABLE(1); clrsetbits_le32(&clk->mpll_con0, clr_pll_con0, set); @@ -220,15 +220,15 @@ static void board_clock_init(void) DMC_RATIO(7) | DMCD_RATIO(7) | DMCP_RATIO(7); /* * For: - * MOUTdmc = 800 MHz - * MOUTdphy = 800 MHz + * MOUTdmc = 880 MHz + * MOUTdphy = 880 MHz * - * aclk_acp = MOUTdmc / (ratio + 1) = 200 (3) - * pclk_acp = aclk_acp / (ratio + 1) = 100 (1) - * sclk_dphy = MOUTdphy / (ratio + 1) = 400 (1) - * sclk_dmc = MOUTdmc / (ratio + 1) = 400 (1) - * aclk_dmcd = sclk_dmc / (ratio + 1) = 200 (1) - * aclk_dmcp = aclk_dmcd / (ratio + 1) = 100 (1) + * aclk_acp = MOUTdmc / (ratio + 1) = 220 (3) + * pclk_acp = aclk_acp / (ratio + 1) = 110 (1) + * sclk_dphy = MOUTdphy / (ratio + 1) = 440 (1) + * sclk_dmc = MOUTdmc / (ratio + 1) = 440 (1) + * aclk_dmcd = sclk_dmc / (ratio + 1) = 220 (1) + * aclk_dmcp = aclk_dmcd / (ratio + 1) = 110 (1) */ set = ACP_RATIO(3) | ACP_PCLK_RATIO(1) | DPHY_RATIO(1) | DMC_RATIO(1) | DMCD_RATIO(1) | DMCP_RATIO(1); @@ -244,13 +244,13 @@ static void board_clock_init(void) C2C_ACLK_RATIO(7) | DVSEM_RATIO(127) | DPM_RATIO(127); /* * For: - * MOUTg2d = 800 MHz - * MOUTc2c = 800 Mhz + * MOUTg2d = 880 MHz + * MOUTc2c = 880 Mhz * MOUTpwi = 108 MHz * - * sclk_g2d_acp = MOUTg2d / (ratio + 1) = 400 (1) - * sclk_c2c = MOUTc2c / (ratio + 1) = 400 (1) - * aclk_c2c = sclk_c2c / (ratio + 1) = 200 (1) + * sclk_g2d_acp = MOUTg2d / (ratio + 1) = 440 (1) + * sclk_c2c = MOUTc2c / (ratio + 1) = 440 (1) + * aclk_c2c = sclk_c2c / (ratio + 1) = 220 (1) * sclk_pwi = MOUTpwi / (ratio + 1) = 18 (5) */ set = G2D_ACP_RATIO(1) | C2C_RATIO(1) | PWI_RATIO(5) | @@ -282,9 +282,9 @@ static void board_clock_init(void) clr = UART0_RATIO(15) | UART1_RATIO(15) | UART2_RATIO(15) | UART3_RATIO(15) | UART4_RATIO(15); /* - * For MOUTuart0-4: 800MHz + * For MOUTuart0-4: 880MHz * - * SCLK_UARTx = MOUTuartX / (ratio + 1) = 100 (7) + * SCLK_UARTx = MOUTuartX / (ratio + 1) = 110 (7) */ set = UART0_RATIO(7) | UART1_RATIO(7) | UART2_RATIO(7) | UART3_RATIO(7) | UART4_RATIO(7); @@ -298,12 +298,12 @@ static void board_clock_init(void) clr = MMC0_RATIO(15) | MMC0_PRE_RATIO(255) | MMC1_RATIO(15) | MMC1_PRE_RATIO(255); /* - * For MOUTmmc0-3 = 800 MHz (MPLL) + * For MOUTmmc0-3 = 880 MHz (MPLL) * - * DOUTmmc1 = MOUTmmc1 / (ratio + 1) = 100 (7) - * sclk_mmc1 = DOUTmmc1 / (ratio + 1) = 50 (1) - * DOUTmmc0 = MOUTmmc0 / (ratio + 1) = 100 (7) - * sclk_mmc0 = DOUTmmc0 / (ratio + 1) = 50 (1) + * DOUTmmc1 = MOUTmmc1 / (ratio + 1) = 110 (7) + * sclk_mmc1 = DOUTmmc1 / (ratio + 1) = 60 (1) + * DOUTmmc0 = MOUTmmc0 / (ratio + 1) = 110 (7) + * sclk_mmc0 = DOUTmmc0 / (ratio + 1) = 60 (1) */ set = MMC0_RATIO(7) | MMC0_PRE_RATIO(1) | MMC1_RATIO(7) | MMC1_PRE_RATIO(1); @@ -318,12 +318,12 @@ static void board_clock_init(void) clr = MMC2_RATIO(15) | MMC2_PRE_RATIO(255) | MMC3_RATIO(15) | MMC3_PRE_RATIO(255); /* - * For MOUTmmc0-3 = 800 MHz (MPLL) + * For MOUTmmc0-3 = 880 MHz (MPLL) * - * DOUTmmc3 = MOUTmmc3 / (ratio + 1) = 100 (7) - * sclk_mmc3 = DOUTmmc3 / (ratio + 1) = 50 (1) - * DOUTmmc2 = MOUTmmc2 / (ratio + 1) = 100 (7) - * sclk_mmc2 = DOUTmmc2 / (ratio + 1) = 50 (1) + * DOUTmmc3 = MOUTmmc3 / (ratio + 1) = 110 (7) + * sclk_mmc3 = DOUTmmc3 / (ratio + 1) = 60 (1) + * DOUTmmc2 = MOUTmmc2 / (ratio + 1) = 110 (7) + * sclk_mmc2 = DOUTmmc2 / (ratio + 1) = 60 (1) */ set = MMC2_RATIO(7) | MMC2_PRE_RATIO(1) | MMC3_RATIO(7) | MMC3_PRE_RATIO(1); @@ -337,10 +337,10 @@ static void board_clock_init(void) /* CLK_DIV_FSYS3 */ clr = MMC4_RATIO(15) | MMC4_PRE_RATIO(255); /* - * For MOUTmmc4 = 800 MHz (MPLL) + * For MOUTmmc4 = 880 MHz (MPLL) * - * DOUTmmc4 = MOUTmmc4 / (ratio + 1) = 100 (7) - * sclk_mmc4 = DOUTmmc4 / (ratio + 1) = 100 (0) + * DOUTmmc4 = MOUTmmc4 / (ratio + 1) = 110 (7) + * sclk_mmc4 = DOUTmmc4 / (ratio + 1) = 110 (0) */ set = MMC4_RATIO(7) | MMC4_PRE_RATIO(0); -- cgit From f0017175e33d7c21269deebc5e2ca2827b1e5975 Mon Sep 17 00:00:00 2001 From: Ajay Kumar Date: Fri, 5 Sep 2014 16:53:30 +0530 Subject: exynos_fb: Remove usage of static defines Previously, we used to statically assign values for vl_col, vl_row and vl_bpix using #defines like LCD_XRES, LCD_YRES and LCD_COLOR16. Introducing the function exynos_lcd_early_init() would take care of this assignment on the fly by parsing FIMD DT properties, thereby allowing us to remove LCD_XRES and LCD_YRES from the main config file. Signed-off-by: Ajay Kumar Acked-by: Simon Glass Tested-by: Simon Glass Signed-off-by: Minkyu Kang --- board/samsung/common/board.c | 16 ++++++++++++++++ 1 file changed, 16 insertions(+) (limited to 'board') diff --git a/board/samsung/common/board.c b/board/samsung/common/board.c index 3d1cf437fa..5c3c5bb925 100644 --- a/board/samsung/common/board.c +++ b/board/samsung/common/board.c @@ -20,6 +20,7 @@ #include #include #include +#include #include #include #include @@ -149,6 +150,21 @@ int board_early_init_f(void) #ifdef CONFIG_SYS_I2C_INIT_BOARD board_i2c_init(gd->fdt_blob); #endif + +#if defined(CONFIG_OF_CONTROL) && defined(CONFIG_EXYNOS_FB) +/* + * board_init_f(arch/arm/lib/board.c) calls lcd_setmem() which needs + * panel_info.vl_col, panel_info.vl_row and panel_info.vl_bpix, to reserve + * FB memory at a very early stage. So, we need to fill panel_info.vl_col, + * panel_info.vl_row and panel_info.vl_bpix before lcd_setmem() is called. + */ + err = exynos_lcd_early_init(gd->fdt_blob); + if (err) { + debug("LCD early init failed\n"); + return err; + } +#endif + return exynos_early_init_f(); } #endif -- cgit From a99cea03132bfc7bb87cb6cfae38c1af5b1bf0b0 Mon Sep 17 00:00:00 2001 From: Ajay Kumar Date: Fri, 5 Sep 2014 16:53:36 +0530 Subject: exynos5420: add callbacks needed for exynos_fb driver Add initialization code for peach_pit panel, parade bridge chip, and backlight. Signed-off-by: Ajay Kumar Acked-by: Simon Glass Tested-by: Simon Glass Signed-off-by: Minkyu Kang --- board/samsung/smdk5420/smdk5420.c | 129 ++++++++++++++------------------------ 1 file changed, 47 insertions(+), 82 deletions(-) (limited to 'board') diff --git a/board/samsung/smdk5420/smdk5420.c b/board/samsung/smdk5420/smdk5420.c index 183c52248a..270ee834e6 100644 --- a/board/samsung/smdk5420/smdk5420.c +++ b/board/samsung/smdk5420/smdk5420.c @@ -10,11 +10,14 @@ #include #include #include +#include #include #include #include #include +#include #include +#include DECLARE_GLOBAL_DATA_PTR; @@ -40,95 +43,57 @@ int exynos_init(void) } #ifdef CONFIG_LCD -void cfg_lcd_gpio(void) +static int has_edp_bridge(void) { - /* For Backlight */ - gpio_cfg_pin(EXYNOS5420_GPIO_B20, S5P_GPIO_OUTPUT); - gpio_set_value(EXYNOS5420_GPIO_B20, 1); + int node; + + node = fdtdec_next_compatible(gd->fdt_blob, 0, COMPAT_PARADE_PS8625); - /* LCD power on */ - gpio_cfg_pin(EXYNOS5420_GPIO_X15, S5P_GPIO_OUTPUT); - gpio_set_value(EXYNOS5420_GPIO_X15, 1); + /* No node for bridge in device tree. */ + if (node <= 0) + return 0; - /* Set Hotplug detect for DP */ - gpio_cfg_pin(EXYNOS5420_GPIO_X07, S5P_GPIO_FUNC(0x3)); + /* Default is with bridge ic */ + return 1; } -vidinfo_t panel_info = { - .vl_freq = 60, - .vl_col = 2560, - .vl_row = 1600, - .vl_width = 2560, - .vl_height = 1600, - .vl_clkp = CONFIG_SYS_LOW, - .vl_hsp = CONFIG_SYS_LOW, - .vl_vsp = CONFIG_SYS_LOW, - .vl_dp = CONFIG_SYS_LOW, - .vl_bpix = 4, /* LCD_BPP = 2^4, for output conosle on LCD */ - - /* wDP panel timing infomation */ - .vl_hspw = 32, - .vl_hbpd = 80, - .vl_hfpd = 48, - - .vl_vspw = 6, - .vl_vbpd = 37, - .vl_vfpd = 3, - .vl_cmd_allow_len = 0xf, - - .win_id = 3, - .cfg_gpio = cfg_lcd_gpio, - .backlight_on = NULL, - .lcd_power_on = NULL, - .reset_lcd = NULL, - .dual_lcd_enabled = 0, - - .init_delay = 0, - .power_on_delay = 0, - .reset_delay = 0, - .interface_mode = FIMD_RGB_INTERFACE, - .dp_enabled = 1, -}; - -static struct edp_device_info edp_info = { - .disp_info = { - .h_res = 2560, - .h_sync_width = 32, - .h_back_porch = 80, - .h_front_porch = 48, - .v_res = 1600, - .v_sync_width = 6, - .v_back_porch = 37, - .v_front_porch = 3, - .v_sync_rate = 60, - }, - .lt_info = { - .lt_status = DP_LT_NONE, - }, - .video_info = { - .master_mode = 0, - .bist_mode = DP_DISABLE, - .bist_pattern = NO_PATTERN, - .h_sync_polarity = 0, - .v_sync_polarity = 0, - .interlaced = 0, - .color_space = COLOR_RGB, - .dynamic_range = VESA, - .ycbcr_coeff = COLOR_YCBCR601, - .color_depth = COLOR_8, - }, -}; - -static struct exynos_dp_platform_data dp_platform_data = { - .phy_enable = set_dp_phy_ctrl, - .edp_dev_info = &edp_info, -}; - -void init_panel_info(vidinfo_t *vid) +void exynos_lcd_power_on(void) { - vid->rgb_mode = MODE_RGB_P; + int ret; + +#ifdef CONFIG_POWER_TPS65090 + ret = tps65090_init(); + if (ret < 0) { + printf("%s: tps65090_init() failed\n", __func__); + return; + } + + tps65090_fet_enable(6); +#endif + + mdelay(5); + + /* TODO(ajaykumar.rs@samsung.com): Use device tree */ + gpio_direction_output(EXYNOS5420_GPIO_X35, 1); /* EDP_SLP# */ + mdelay(10); + gpio_direction_output(EXYNOS5420_GPIO_Y77, 1); /* EDP_RST# */ + gpio_direction_input(EXYNOS5420_GPIO_X26); /* EDP_HPD */ + gpio_set_pull(EXYNOS5420_GPIO_X26, S5P_GPIO_PULL_NONE); - exynos_set_dp_platform_data(&dp_platform_data); + if (has_edp_bridge()) + if (parade_init(gd->fdt_blob)) + printf("%s: ps8625_init() failed\n", __func__); +} + +void exynos_backlight_on(unsigned int onoff) +{ + /* For PWM */ + gpio_cfg_pin(EXYNOS5420_GPIO_B20, S5P_GPIO_FUNC(0x1)); + gpio_set_value(EXYNOS5420_GPIO_B20, 1); + +#ifdef CONFIG_POWER_TPS65090 + tps65090_fet_enable(1); +#endif } #endif -- cgit