From 1a103c6caa0b27fcd3798267b980444f5459860f Mon Sep 17 00:00:00 2001
From: Stefan Roese <sr@denx.de>
Date: Wed, 2 Sep 2015 14:29:12 +0200
Subject: mtd: nand: fsmc: Add BCH4 SW ECC support for SPEAr600

This patch adds support for 4-bit ECC BCH4 for the SPEAr600 SoC. This can
be used by boards equipped with a NAND chip that requires 4-bit ECC strength.
The SPEAr600 HW ECC only supports 1-bit ECC strength.

To enable SW BCH4, you need to specify this in your config header:

#define CONFIG_NAND_ECC_BCH
#define CONFIG_BCH

And use the command "nandecc bch4" to select this ECC scheme upon runtime.

Tested on SPEAr600 x600 board.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
---
 drivers/mtd/nand/fsmc_nand.c | 40 ++++++++++++++++++++++++++++++++++++++++
 1 file changed, 40 insertions(+)

(limited to 'drivers')

diff --git a/drivers/mtd/nand/fsmc_nand.c b/drivers/mtd/nand/fsmc_nand.c
index 567eff0914..0976a67ff8 100644
--- a/drivers/mtd/nand/fsmc_nand.c
+++ b/drivers/mtd/nand/fsmc_nand.c
@@ -13,6 +13,7 @@
 #include <asm/io.h>
 #include <linux/bitops.h>
 #include <linux/err.h>
+#include <linux/mtd/nand_bch.h>
 #include <linux/mtd/nand_ecc.h>
 #include <linux/mtd/fsmc_nand.h>
 #include <asm/arch/hardware.h>
@@ -390,6 +391,45 @@ static int fsmc_read_page_hwecc(struct mtd_info *mtd, struct nand_chip *chip,
 	return 0;
 }
 
+#ifndef CONFIG_SPL_BUILD
+/*
+ * fsmc_nand_switch_ecc - switch the ECC operation between different engines
+ *
+ * @eccstrength		- the number of bits that could be corrected
+ *			  (1 - HW, 4 - SW BCH4)
+ */
+int __maybe_unused fsmc_nand_switch_ecc(uint32_t eccstrength)
+{
+	struct nand_chip *nand;
+	struct mtd_info *mtd;
+	int err;
+
+	mtd = &nand_info[nand_curr_device];
+	nand = mtd->priv;
+
+	/* Setup the ecc configurations again */
+	if (eccstrength == 1) {
+		nand->ecc.mode = NAND_ECC_HW;
+		nand->ecc.bytes = 3;
+		nand->ecc.strength = 1;
+		nand->ecc.layout = &fsmc_ecc1_layout;
+		nand->ecc.correct = nand_correct_data;
+	} else {
+		nand->ecc.mode = NAND_ECC_SOFT_BCH;
+		nand->ecc.calculate = nand_bch_calculate_ecc;
+		nand->ecc.correct = nand_bch_correct_data;
+		nand->ecc.bytes = 7;
+		nand->ecc.strength = 4;
+		nand->ecc.layout = NULL;
+	}
+
+	/* Update NAND handling after ECC mode switch */
+	err = nand_scan_tail(mtd);
+
+	return err;
+}
+#endif /* CONFIG_SPL_BUILD */
+
 int fsmc_nand_init(struct nand_chip *nand)
 {
 	static int chip_nr;
-- 
cgit