From 39f633320c569a5d975d2d051ff2683db27bd021 Mon Sep 17 00:00:00 2001 From: Stephen Warren Date: Thu, 12 May 2016 12:11:23 -0600 Subject: mmc: tegra: add basic Tegra186 support Tegra186's MMC controller needs to be explicitly identified. Add another compatible value for it. Tegra186 will use an entirely different clock/reset control mechanism to existing chips, and will use standard clock/reset APIs rather than the existing Tegra-specific custom APIs. The driver support for that isn't ready yet, so simply disable all clock/reset usage if compiling for Tegra186. This must happen at compile time rather than run-time since the custom APIs won't even be compiled in on Tegra186. In the long term, the plan would be to convert the existing custom APIs to standard APIs and get rid of the ifdefs completely. The system's main eMMC will work without any clock/reset support, since the firmware will have already initialized the controller in order to load U-Boot. Hence the driver is useful even in this apparently crippled state. Signed-off-by: Stephen Warren Signed-off-by: Tom Warren --- drivers/mmc/tegra_mmc.c | 32 +++++++++++++++++++++++++++++++- 1 file changed, 31 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/mmc/tegra_mmc.c b/drivers/mmc/tegra_mmc.c index 573819a01e..c9d9432e5e 100644 --- a/drivers/mmc/tegra_mmc.c +++ b/drivers/mmc/tegra_mmc.c @@ -11,8 +11,10 @@ #include #include #include +#ifndef CONFIG_TEGRA186 #include #include +#endif #include #include #include @@ -357,8 +359,12 @@ static void mmc_change_clock(struct mmc_host *host, uint clock) */ if (clock == 0) goto out; +#ifndef CONFIG_TEGRA186 clock_adjust_periph_pll_div(host->mmc_id, CLOCK_ID_PERIPH, clock, &div); +#else + div = (20000000 + clock - 1) / clock; +#endif debug("div = %d\n", div); writew(0, &host->reg->clkcon); @@ -543,7 +549,9 @@ static int do_mmc_init(int dev_index, bool removable) gpio_get_number(&host->cd_gpio)); host->clock = 0; +#ifndef CONFIG_TEGRA186 clock_start_periph_pll(host->mmc_id, CLOCK_ID_PERIPH, 20000000); +#endif if (dm_gpio_is_valid(&host->pwr_gpio)) dm_gpio_set_value(&host->pwr_gpio, 1); @@ -568,7 +576,11 @@ static int do_mmc_init(int dev_index, bool removable) * (actually 52MHz) */ host->cfg.f_min = 375000; +#ifndef CONFIG_TEGRA186 host->cfg.f_max = 48000000; +#else + host->cfg.f_max = 375000; +#endif host->cfg.b_max = CONFIG_SYS_MMC_MAX_BLK_COUNT; @@ -600,11 +612,13 @@ static int mmc_get_config(const void *blob, int node, struct mmc_host *host, return -FDT_ERR_NOTFOUND; } +#ifndef CONFIG_TEGRA186 host->mmc_id = clock_decode_periph_id(blob, node); if (host->mmc_id == PERIPH_ID_NONE) { debug("%s: could not decode periph id\n", __func__); return -FDT_ERR_NOTFOUND; } +#endif /* * NOTE: mmc->bus_width is determined by mmc.c dynamically. @@ -624,7 +638,13 @@ static int mmc_get_config(const void *blob, int node, struct mmc_host *host, *removablep = !fdtdec_get_bool(blob, node, "non-removable"); debug("%s: found controller at %p, width = %d, periph_id = %d\n", - __func__, host->reg, host->width, host->mmc_id); + __func__, host->reg, host->width, +#ifndef CONFIG_TEGRA186 + host->mmc_id +#else + -1 +#endif + ); return 0; } @@ -668,6 +688,16 @@ void tegra_mmc_init(void) const void *blob = gd->fdt_blob; debug("%s entry\n", __func__); + /* See if any Tegra186 MMC controllers are present */ + count = fdtdec_find_aliases_for_id(blob, "sdhci", + COMPAT_NVIDIA_TEGRA186_SDMMC, node_list, + CONFIG_SYS_MMC_MAX_DEVICE); + debug("%s: count of Tegra186 sdhci nodes is %d\n", __func__, count); + if (process_nodes(blob, node_list, count)) { + printf("%s: Error processing T186 mmc node(s)!\n", __func__); + return; + } + /* See if any Tegra210 MMC controllers are present */ count = fdtdec_find_aliases_for_id(blob, "sdhci", COMPAT_NVIDIA_TEGRA210_SDMMC, node_list, -- cgit