From a9a5cef391ed5b2e47ed02a8cecf0ab1a19fc76a Mon Sep 17 00:00:00 2001 From: Alison Wang Date: Tue, 16 May 2017 10:45:58 +0800 Subject: armv8: layerscape: Adjust memory mapping for Flash/SD card on LS1043A This patch is to adjust the memory mapping for FLash/SD card on LS1043AQDS and LS1043ARDB, such as PPA firmware load address, FMAN firmware load address, QE firmware load address, U-Boot start address on serial flash and environment address. Signed-off-by: Alison Wang Reviewed-by: York Sun --- include/configs/ls1043a_common.h | 12 ++++++------ 1 file changed, 6 insertions(+), 6 deletions(-) (limited to 'include/configs/ls1043a_common.h') diff --git a/include/configs/ls1043a_common.h b/include/configs/ls1043a_common.h index e26924877d..05419fe9fb 100644 --- a/include/configs/ls1043a_common.h +++ b/include/configs/ls1043a_common.h @@ -208,20 +208,20 @@ #define CONFIG_SYS_FM_MURAM_SIZE 0x60000 #ifdef CONFIG_NAND_BOOT -/* Store Fman ucode at offeset 0x160000(11 blocks). */ +/* Store Fman ucode at offeset 0x900000(72 blocks). */ #define CONFIG_SYS_QE_FMAN_FW_IN_NAND -#define CONFIG_SYS_FMAN_FW_ADDR (11 * CONFIG_SYS_NAND_BLOCK_SIZE) +#define CONFIG_SYS_FMAN_FW_ADDR (72 * CONFIG_SYS_NAND_BLOCK_SIZE) #elif defined(CONFIG_SD_BOOT) /* * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is * about 1MB (2040 blocks), Env is stored after the image, and the env size is - * 0x2000 (16 blocks), 8 + 2040 + 16 = 2064, enlarge it to 2080(0x820). + * 0x2000 (16 blocks), 8 + 2040 + 16 = 2064, enlarge it to 18432(0x4800). */ #define CONFIG_SYS_QE_FMAN_FW_IN_MMC -#define CONFIG_SYS_FMAN_FW_ADDR (512 * 0x820) +#define CONFIG_SYS_FMAN_FW_ADDR (512 * 0x4800) #elif defined(CONFIG_QSPI_BOOT) #define CONFIG_SYS_QE_FW_IN_SPIFLASH -#define CONFIG_SYS_FMAN_FW_ADDR 0x400d0000 +#define CONFIG_SYS_FMAN_FW_ADDR 0x40900000 #define CONFIG_ENV_SPI_BUS 0 #define CONFIG_ENV_SPI_CS 0 #define CONFIG_ENV_SPI_MAX_HZ 1000000 @@ -229,7 +229,7 @@ #else #define CONFIG_SYS_QE_FMAN_FW_IN_NOR /* FMan fireware Pre-load address */ -#define CONFIG_SYS_FMAN_FW_ADDR 0x60300000 +#define CONFIG_SYS_FMAN_FW_ADDR 0x60900000 #endif #define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 #define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH) -- cgit