From 517c5dfed5107fe1d77dd1e003c3c076bcf279e6 Mon Sep 17 00:00:00 2001 From: Michael Schwingen Date: Mon, 23 May 2011 00:00:04 +0200 Subject: update/fix AcTux1 board Signed-off-by: Michael Schwingen --- include/configs/actux1.h | 62 ++++++++++++++++++++++++++++-------------------- 1 file changed, 36 insertions(+), 26 deletions(-) (limited to 'include/configs') diff --git a/include/configs/actux1.h b/include/configs/actux1.h index 8121b27229..160c10af29 100644 --- a/include/configs/actux1.h +++ b/include/configs/actux1.h @@ -26,13 +26,6 @@ #ifndef __CONFIG_H #define __CONFIG_H -/* 1: modified board with 32MB DRAM */ -#define CONFIG_ACTUX1_32MB 0 -/* 1: 2*2MB FLASH (standard) */ -#define CONFIG_ACTUX1_FLASH2X2 1 -/* 1: 1*8MB FLASH (upgraded boards) */ -#define CONFIG_ACTUX1_FLASH1X8 0 - #define CONFIG_IXP425 1 #define CONFIG_ACTUX1 1 @@ -44,12 +37,12 @@ #define CONFIG_BAUDRATE 115200 #define CONFIG_BOOTDELAY 3 #define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ +#define CONFIG_BOARD_EARLY_INIT_F 1 +#define CONFIG_SYS_LDSCRIPT "board/actux1/u-boot.lds" /*************************************************************** * U-boot generic defines start here. ***************************************************************/ -#undef CONFIG_USE_IRQ - /* * Size of malloc() pool */ @@ -62,8 +55,13 @@ #include #define CONFIG_CMD_ELF -#undef CONFIG_CMD_PCI -#undef CONFIG_PCI +#ifdef CONFIG_PCI +#define CONFIG_CMD_PCI +#define CONFIG_PCI_PNP +#define CONFIG_IXP_PCI +#define CONFIG_PCI_SCAN_SHOW +#define CONFIG_CMD_PCI_ENUM +#endif #define CONFIG_BOOTCOMMAND "run boot_flash" /* enable passing of ATAGs */ @@ -93,8 +91,9 @@ #define CONFIG_SYS_MEMTEST_START 0x00400000 #define CONFIG_SYS_MEMTEST_END 0x00800000 -/* spec says 66.666 MHz, but it appears to be 33 */ -#define CONFIG_SYS_HZ 3333333 +/* timer clock - 2* OSC_IN system clock */ +#define CONFIG_IXP425_TIMER_CLK 66666666 +#define CONFIG_SYS_HZ 1000 /* default load address */ #define CONFIG_SYS_LOAD_ADDR 0x00010000 @@ -109,10 +108,6 @@ * The stack sizes are set up in start.S using the settings below */ #define CONFIG_STACKSIZE (128*1024) /* regular stack */ -#ifdef CONFIG_USE_IRQ -# define CONFIG_STACKSIZE_IRQ (4*1024) /* IRQ stack */ -# define CONFIG_STACKSIZE_FIQ (4*1024) /* FIQ stack */ -#endif /* Expansion bus settings */ #define CONFIG_SYS_EXP_CS0 0xbd113842 @@ -120,9 +115,9 @@ /* SDRAM settings */ #define CONFIG_NR_DRAM_BANKS 1 #define PHYS_SDRAM_1 0x00000000 -#define CONFIG_SYS_DRAM_BASE 0x00000000 +#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#if CONFIG_ACTUX1_32MB +#ifdef CONFIG_RAM_32MB # define CONFIG_SYS_SDR_CONFIG 0x18 # define PHYS_SDRAM_1_SIZE 0x02000000 # define CONFIG_SYS_SDRAM_REFRESH_CNT 0x81a @@ -136,8 +131,11 @@ # define CONFIG_SYS_DRAM_SIZE 0x01000000 #endif + + /* FLASH organization */ -#if CONFIG_ACTUX1_FLASH2X2 +#define CONFIG_SYS_TEXT_BASE 0x50000000 +#ifdef CONFIG_FLASH2X2 # define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of sectors on one chip */ # define CONFIG_SYS_MAX_FLASH_SECT 40 @@ -145,7 +143,7 @@ # define PHYS_FLASH_2 0x50200000 # define CONFIG_SYS_FLASH_BANKS_LIST { PHYS_FLASH_1, PHYS_FLASH_2 } #endif -#if CONFIG_ACTUX1_FLASH1X8 +#ifdef CONFIG_FLASH1X8 # define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of sectors on one chip */ # define CONFIG_SYS_MAX_FLASH_SECT 140 @@ -156,6 +154,7 @@ #define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1 #define CONFIG_SYS_MONITOR_BASE PHYS_FLASH_1 #define CONFIG_SYS_MONITOR_LEN (256 << 10) +#define CONFIG_BOARD_SIZE_LIMIT 262144 /* Use common CFI driver */ #define CONFIG_SYS_FLASH_CFI @@ -172,12 +171,16 @@ #define CONFIG_NET_MULTI 1 /* NPE0 PHY address */ #define CONFIG_PHY_ADDR 0 +/* NPE1 PHY address (HW Release E only) */ +#define CONFIG_PHY1_ADDR 1 /* MII PHY management */ #define CONFIG_MII 1 /* Number of ethernet rx buffers & descriptors */ #define CONFIG_SYS_RX_ETH_BUFFER 16 #define CONFIG_RESET_PHY_R 1 +#define CONFIG_HAS_ETH1 1 + #define CONFIG_CMD_DHCP #define CONFIG_CMD_NET #define CONFIG_CMD_MII @@ -202,17 +205,19 @@ #define CONFIG_ENV_ADDR (PHYS_FLASH_1 + 0x4000) #define CONFIG_SYS_USE_PPCENV 1 -#define CONFIG_EXTRA_ENV_SETTINGS \ +#define CONFIG_EXTRA_ENV_SETTINGS \ "npe_ucode=50040000\0" \ "mtd=IXP4XX-Flash.0:256k(uboot),64k(ucode),1152k(linux),-(root)\0" \ "kerneladdr=50050000\0" \ + "kernelfile=actux1/uImage\0" \ + "rootfile=actux1/rootfs\0" \ "rootaddr=50170000\0" \ "loadaddr=10000\0" \ "updateboot_ser=mw.b 10000 ff 40000;" \ " loady ${loadaddr};" \ " run eraseboot writeboot\0" \ "updateboot_net=mw.b 10000 ff 40000;" \ - " tftp ${loadaddr} u-boot.bin;" \ + " tftp ${loadaddr} actux1/u-boot.bin;" \ " run eraseboot writeboot\0" \ "eraseboot=protect off 50000000 50003fff;" \ " protect off 50006000 5003ffff;" \ @@ -220,8 +225,9 @@ " erase 50006000 5003ffff\0" \ "writeboot=cp.b 10000 50000000 4000;" \ " cp.b 16000 50006000 3a000\0" \ - "eraseenv=protect off 50004000 50005fff;" \ - " erase 50004000 50005fff\0" \ + "updateucode=loady;" \ + " era ${npe_ucode} +${filesize};" \ + " cp.b ${loadaddr} ${npe_ucode} ${filesize}\0" \ "updateroot=tftp ${loadaddr} ${rootfile};" \ " era ${rootaddr} +${filesize};" \ " cp.b ${loadaddr} ${rootaddr} ${filesize}\0" \ @@ -232,7 +238,7 @@ " rootfstype=squashfs,jffs2 init=/etc/preinit\0" \ "netargs=setenv bootargs mtdparts=${mtd} root=/dev/mtdblock3" \ " rootfstype=squashfs,jffs2 init=/etc/preinit\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0" \ + "addtty=setenv bootargs ${bootargs} console=ttyS1,${baudrate}\0" \ "addeth=setenv bootargs ${bootargs} ethaddr=${ethaddr}\0" \ "boot_flash=run flashargs addtty addeth;" \ " bootm ${kerneladdr}\0" \ @@ -240,4 +246,8 @@ " tftpboot ${loadaddr} ${kernelfile};" \ " bootm\0" +/* additions for new relocation code, must be added to all boards */ +#define CONFIG_SYS_INIT_SP_ADDR \ + (CONFIG_SYS_SDRAM_BASE + 0x1000 - GENERATED_GBL_DATA_SIZE) + #endif /* __CONFIG_H */ -- cgit From af0504858ca2651e32e15f2efe9ec9fcd0b7d57f Mon Sep 17 00:00:00 2001 From: Michael Schwingen Date: Mon, 23 May 2011 00:00:05 +0200 Subject: update/fix AcTux2 board Signed-off-by: Michael Schwingen --- include/configs/actux2.h | 35 +++++++++++++++++++++++------------ 1 file changed, 23 insertions(+), 12 deletions(-) (limited to 'include/configs') diff --git a/include/configs/actux2.h b/include/configs/actux2.h index 8ab3b19933..eca814b3ee 100644 --- a/include/configs/actux2.h +++ b/include/configs/actux2.h @@ -37,12 +37,12 @@ #define CONFIG_BAUDRATE 115200 #define CONFIG_BOOTDELAY 5 #define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ +#define CONFIG_BOARD_EARLY_INIT_F 1 +#define CONFIG_SYS_LDSCRIPT "board/actux2/u-boot.lds" /*************************************************************** * U-boot generic defines start here. ***************************************************************/ -#undef CONFIG_USE_IRQ - /* Size of malloc() pool */ #define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024) @@ -84,8 +84,9 @@ #define CONFIG_SYS_MEMTEST_START 0x00400000 #define CONFIG_SYS_MEMTEST_END 0x00800000 -/* spec says 66.666 MHz, but it appears to be 33 */ -#define CONFIG_SYS_HZ 3333333 +/* timer clock - 2* OSC_IN system clock */ +#define CONFIG_IXP425_TIMER_CLK 66666666 +#define CONFIG_SYS_HZ 1000 /* default load address */ #define CONFIG_SYS_LOAD_ADDR 0x00010000 @@ -100,10 +101,6 @@ * The stack sizes are set up in start.S using the settings below */ #define CONFIG_STACKSIZE (128*1024) /* regular stack */ -#ifdef CONFIG_USE_IRQ -# define CONFIG_STACKSIZE_IRQ (4*1024) /* IRQ stack */ -# define CONFIG_STACKSIZE_FIQ (4*1024) /* FIQ stack */ -#endif /* Expansion bus settings */ #define CONFIG_SYS_EXP_CS0 0xbd113042 @@ -111,7 +108,7 @@ /* SDRAM settings */ #define CONFIG_NR_DRAM_BANKS 1 #define PHYS_SDRAM_1 0x00000000 -#define CONFIG_SYS_DRAM_BASE 0x00000000 +#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* 16MB SDRAM */ #define CONFIG_SYS_SDR_CONFIG 0x3A @@ -121,6 +118,7 @@ #define CONFIG_SYS_DRAM_SIZE 0x01000000 /* FLASH organization */ +#define CONFIG_SYS_TEXT_BASE 0x50000000 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of sectors on one chip */ #define CONFIG_SYS_MAX_FLASH_SECT 140 @@ -130,6 +128,7 @@ #define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1 #define CONFIG_SYS_MONITOR_BASE PHYS_FLASH_1 #define CONFIG_SYS_MONITOR_LEN (256 << 10) +#define CONFIG_BOARD_SIZE_LIMIT 262144 /* Use common CFI driver */ #define CONFIG_SYS_FLASH_CFI @@ -149,6 +148,11 @@ #define CONFIG_PHY_ADDR 0x00 /* MII PHY management */ #define CONFIG_MII 1 +/* fixed-speed switch without standard PHY registers on MII */ +#define CONFIG_MII_NPE0_FIXEDLINK 1 +#define CONFIG_MII_NPE0_SPEED 100 +#define CONFIG_MII_NPE0_FULLDUPLEX 1 + /* Number of ethernet rx buffers & descriptors */ #define CONFIG_SYS_RX_ETH_BUFFER 16 #define CONFIG_RESET_PHY_R 1 @@ -183,13 +187,15 @@ "npe_ucode=50040000\0" \ "mtd=IXP4XX-Flash.0:256k(uboot),64k(ucode),1152k(linux),-(root)\0" \ "kerneladdr=50050000\0" \ + "kernelfile=actux2/uImage\0" \ + "rootfile=actux2/rootfs\0" \ "rootaddr=50170000\0" \ "loadaddr=10000\0" \ "updateboot_ser=mw.b 10000 ff 40000;" \ " loady ${loadaddr};" \ " run eraseboot writeboot\0" \ "updateboot_net=mw.b 10000 ff 40000;" \ - " tftp ${loadaddr} u-boot.bin;" \ + " tftp ${loadaddr} actux2/u-boot.bin;" \ " run eraseboot writeboot\0" \ "eraseboot=protect off 50000000 50003fff;" \ " protect off 50006000 5003ffff;" \ @@ -197,8 +203,9 @@ " erase 50006000 5003ffff\0" \ "writeboot=cp.b 10000 50000000 4000;" \ " cp.b 16000 50006000 3a000\0" \ - "eraseenv=protect off 50004000 50005fff;" \ - " erase 50004000 50005fff\0" \ + "updateucode=loady;" \ + " era ${npe_ucode} +${filesize};" \ + " cp.b ${loadaddr} ${npe_ucode} ${filesize}\0" \ "updateroot=tftp ${loadaddr} ${rootfile};" \ " era ${rootaddr} +${filesize};" \ " cp.b ${loadaddr} ${rootaddr} ${filesize}\0" \ @@ -217,4 +224,8 @@ " tftpboot ${loadaddr} ${kernelfile};" \ " bootm\0" +/* additions for new relocation code, must be added to all boards */ +#define CONFIG_SYS_INIT_SP_ADDR \ + (CONFIG_SYS_SDRAM_BASE + 0x1000 - GENERATED_GBL_DATA_SIZE) + #endif /* __CONFIG_H */ -- cgit From 8b5ab4c1b6622b30f060708cd8b66a8e97d61268 Mon Sep 17 00:00:00 2001 From: Michael Schwingen Date: Mon, 23 May 2011 00:00:06 +0200 Subject: update/fix AcTux3 board Signed-off-by: Michael Schwingen --- include/configs/actux3.h | 37 ++++++++++++++++++++++++------------- 1 file changed, 24 insertions(+), 13 deletions(-) (limited to 'include/configs') diff --git a/include/configs/actux3.h b/include/configs/actux3.h index 91987cbce5..c103312402 100644 --- a/include/configs/actux3.h +++ b/include/configs/actux3.h @@ -37,12 +37,12 @@ #define CONFIG_BAUDRATE 115200 #define CONFIG_BOOTDELAY 3 #define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ +#define CONFIG_BOARD_EARLY_INIT_F 1 +#define CONFIG_SYS_LDSCRIPT "board/actux3/u-boot.lds" /*************************************************************** * U-boot generic defines start here. ***************************************************************/ -#undef CONFIG_USE_IRQ - /* Size of malloc() pool */ #define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024) @@ -82,8 +82,9 @@ #define CONFIG_SYS_MEMTEST_START 0x00400000 #define CONFIG_SYS_MEMTEST_END 0x00800000 -/* spec says 66.666 MHz, but it appears to be 33 */ -#define CONFIG_SYS_HZ 3333333 +/* timer clock - 2* OSC_IN system clock */ +#define CONFIG_IXP425_TIMER_CLK 66666666 +#define CONFIG_SYS_HZ 1000 /* default load address */ #define CONFIG_SYS_LOAD_ADDR 0x00010000 @@ -99,10 +100,6 @@ * The stack sizes are set up in start.S using the settings below */ #define CONFIG_STACKSIZE (128*1024) /* regular stack */ -#ifdef CONFIG_USE_IRQ -# define CONFIG_STACKSIZE_IRQ (4*1024) /* IRQ stack */ -# define CONFIG_STACKSIZE_FIQ (4*1024) /* FIQ stack */ -#endif /* Expansion bus settings */ #define CONFIG_SYS_EXP_CS0 0xbd113442 @@ -110,7 +107,7 @@ /* SDRAM settings */ #define CONFIG_NR_DRAM_BANKS 1 #define PHYS_SDRAM_1 0x00000000 -#define CONFIG_SYS_DRAM_BASE 0x00000000 +#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* 16MB SDRAM */ #define CONFIG_SYS_SDR_CONFIG 0x3A @@ -120,6 +117,7 @@ #define CONFIG_SYS_DRAM_SIZE 0x01000000 /* FLASH organization */ +#define CONFIG_SYS_TEXT_BASE 0x50000000 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of sectors on one chip */ #define CONFIG_SYS_MAX_FLASH_SECT 140 @@ -129,6 +127,7 @@ #define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1 #define CONFIG_SYS_MONITOR_BASE PHYS_FLASH_1 #define CONFIG_SYS_MONITOR_LEN (256 << 10) +#define CONFIG_BOARD_SIZE_LIMIT 262144 /* Use common CFI driver */ #define CONFIG_SYS_FLASH_CFI @@ -149,6 +148,11 @@ #define CONFIG_PHY_ADDR 0x10 /* MII PHY management */ #define CONFIG_MII 1 +/* fixed-speed switch without standard PHY registers on MII */ +#define CONFIG_MII_NPE0_FIXEDLINK 1 +#define CONFIG_MII_NPE0_SPEED 100 +#define CONFIG_MII_NPE0_FULLDUPLEX 1 + /* Number of ethernet rx buffers & descriptors */ #define CONFIG_SYS_RX_ETH_BUFFER 16 #define CONFIG_RESET_PHY_R 1 @@ -183,13 +187,15 @@ "npe_ucode=50040000\0" \ "mtd=IXP4XX-Flash.0:256k(uboot),64k(ucode),1152k(linux),-(root)\0" \ "kerneladdr=50050000\0" \ + "kernelfile=actux3/uImage\0" \ + "rootfile=actux3/rootfs\0" \ "rootaddr=50170000\0" \ "loadaddr=10000\0" \ "updateboot_ser=mw.b 10000 ff 40000;" \ " loady ${loadaddr};" \ " run eraseboot writeboot\0" \ "updateboot_net=mw.b 10000 ff 40000;" \ - " tftp ${loadaddr} u-boot.bin;" \ + " tftp ${loadaddr} actux3/u-boot.bin;" \ " run eraseboot writeboot\0" \ "eraseboot=protect off 50000000 50003fff;" \ " protect off 50006000 5003ffff;" \ @@ -197,8 +203,9 @@ " erase 50006000 5003ffff\0" \ "writeboot=cp.b 10000 50000000 4000;" \ " cp.b 16000 50006000 3a000\0" \ - "eraseenv=protect off 50004000 50005fff;" \ - " erase 50004000 50005fff\0" \ + "updateucode=loady;" \ + " era ${npe_ucode} +${filesize};" \ + " cp.b ${loadaddr} ${npe_ucode} ${filesize}\0" \ "updateroot=tftp ${loadaddr} ${rootfile};" \ " era ${rootaddr} +${filesize};" \ " cp.b ${loadaddr} ${rootaddr} ${filesize}\0" \ @@ -209,7 +216,7 @@ " rootfstype=squashfs,jffs2 init=/etc/preinit\0" \ "netargs=setenv bootargs mtdparts=${mtd} root=/dev/mtdblock3" \ " rootfstype=squashfs,jffs2 init=/etc/preinit\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0" \ + "addtty=setenv bootargs ${bootargs} console=ttyS1,${baudrate}\0" \ "addeth=setenv bootargs ${bootargs} ethaddr=${ethaddr}\0" \ "boot_flash=run flashargs addtty addeth;" \ " bootm ${kerneladdr}\0" \ @@ -217,4 +224,8 @@ " tftpboot ${loadaddr} ${kernelfile};" \ " bootm\0" +/* additions for new relocation code, must be added to all boards */ +#define CONFIG_SYS_INIT_SP_ADDR \ + (CONFIG_SYS_SDRAM_BASE + 0x1000 - GENERATED_GBL_DATA_SIZE) + #endif /* __CONFIG_H */ -- cgit From 080b7643fb93ad058ab40da27533d7b9ed8b6c6d Mon Sep 17 00:00:00 2001 From: Michael Schwingen Date: Mon, 23 May 2011 00:00:07 +0200 Subject: update/fix AcTux4 board Signed-off-by: Michael Schwingen --- include/configs/actux4.h | 39 +++++++++++++++++++++++++++------------ 1 file changed, 27 insertions(+), 12 deletions(-) (limited to 'include/configs') diff --git a/include/configs/actux4.h b/include/configs/actux4.h index 67189216d5..190de5a390 100644 --- a/include/configs/actux4.h +++ b/include/configs/actux4.h @@ -37,12 +37,11 @@ #define CONFIG_BAUDRATE 115200 #define CONFIG_BOOTDELAY 3 #define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ +#define CONFIG_BOARD_EARLY_INIT_F 1 /*************************************************************** * U-boot generic defines start here. ***************************************************************/ -#undef CONFIG_USE_IRQ - /* Size of malloc() pool */ #define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024) @@ -54,6 +53,15 @@ #define CONFIG_CMD_ELF +#define CONFIG_PCI +#ifdef CONFIG_PCI +#define CONFIG_CMD_PCI +#define CONFIG_PCI_PNP +#define CONFIG_IXP_PCI +#define CONFIG_PCI_SCAN_SHOW +#define CONFIG_CMD_PCI_ENUM +#endif + #define CONFIG_BOOTCOMMAND "run boot_flash" /* enable passing of ATAGs */ #define CONFIG_CMDLINE_TAG 1 @@ -81,8 +89,9 @@ #define CONFIG_SYS_MEMTEST_START 0x00400000 #define CONFIG_SYS_MEMTEST_END 0x00800000 -/* spec says 66.666 MHz, but it appears to be 33 */ -#define CONFIG_SYS_HZ 3333333 +/* timer clock - 2* OSC_IN system clock */ +#define CONFIG_IXP425_TIMER_CLK 66000000 +#define CONFIG_SYS_HZ 1000 /* default load address */ #define CONFIG_SYS_LOAD_ADDR 0x00010000 @@ -97,10 +106,6 @@ * The stack sizes are set up in start.S using the settings below */ #define CONFIG_STACKSIZE (128*1024) /* regular stack */ -#ifdef CONFIG_USE_IRQ -# define CONFIG_STACKSIZE_IRQ (4*1024) /* IRQ stack */ -# define CONFIG_STACKSIZE_FIQ (4*1024) /* FIQ stack */ -#endif /* Expansion bus settings */ #define CONFIG_SYS_EXP_CS0 0xbd113003 @@ -108,7 +113,7 @@ /* SDRAM settings */ #define CONFIG_NR_DRAM_BANKS 1 #define PHYS_SDRAM_1 0x00000000 -#define CONFIG_SYS_DRAM_BASE 0x00000000 +#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* 32MB SDRAM */ #define CONFIG_SYS_SDR_CONFIG 0x18 @@ -118,6 +123,7 @@ #define CONFIG_SYS_DRAM_SIZE 0x02000000 /* FLASH organization */ +#define CONFIG_SYS_TEXT_BASE 0x50000000 #define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max # of sectors per chip */ #define CONFIG_SYS_MAX_FLASH_SECT 70 @@ -128,6 +134,7 @@ #define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1 #define CONFIG_SYS_MONITOR_BASE PHYS_FLASH_1 #define CONFIG_SYS_MONITOR_LEN (252 << 10) +#define CONFIG_BOARD_SIZE_LIMIT 258048 /* Use common CFI driver */ #define CONFIG_SYS_FLASH_CFI @@ -152,6 +159,7 @@ #define CONFIG_PHY_ADDR 0x1C /* MII PHY management */ #define CONFIG_MII 1 + /* Number of ethernet rx buffers & descriptors */ #define CONFIG_SYS_RX_ETH_BUFFER 16 @@ -180,19 +188,22 @@ "mtd=IXP4XX-Flash.0:252k(uboot),4k(uboot_env);" \ "IXP4XX-Flash.1:128k(ucode),1280k(linux),-(root)\0" \ "kerneladdr=51020000\0" \ + "kernelfile=actux4/uImage\0" \ + "rootfile=actux4/rootfs\0" \ "rootaddr=51160000\0" \ "loadaddr=10000\0" \ "updateboot_ser=mw.b 10000 ff 40000;" \ " loady ${loadaddr};" \ " run eraseboot writeboot\0" \ "updateboot_net=mw.b 10000 ff 40000;" \ - " tftp ${loadaddr} u-boot.bin;" \ + " tftp ${loadaddr} actux4/u-boot.bin;" \ " run eraseboot writeboot\0" \ "eraseboot=protect off 50000000 5003efff;" \ " erase 50000000 +${filesize}\0" \ "writeboot=cp.b 10000 50000000 ${filesize}\0" \ - "eraseenv=protect off 5003f000 5003ffff;" \ - " erase 5003f000 5003ffff\0" \ + "updateucode=loady;" \ + " era ${npe_ucode} +${filesize};" \ + " cp.b ${loadaddr} ${npe_ucode} ${filesize}\0" \ "updateroot=tftp ${loadaddr} ${rootfile};" \ " era ${rootaddr} +${filesize};" \ " cp.b ${loadaddr} ${rootaddr} ${filesize}\0" \ @@ -211,4 +222,8 @@ " tftpboot ${loadaddr} ${kernelfile};" \ " bootm\0" +/* additions for new relocation code, must be added to all boards */ +#define CONFIG_SYS_INIT_SP_ADDR \ + (CONFIG_SYS_SDRAM_BASE + 0x1000 - GENERATED_GBL_DATA_SIZE) + #endif /* __CONFIG_H */ -- cgit From 10c9787e683205aa780dba53fa9f43cdd529bec9 Mon Sep 17 00:00:00 2001 From: Michael Schwingen Date: Mon, 23 May 2011 00:00:09 +0200 Subject: add dvlhost (dLAN 200 AV Wireless G) board Signed-off-by: Michael Schwingen --- include/configs/dvlhost.h | 248 ++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 248 insertions(+) create mode 100644 include/configs/dvlhost.h (limited to 'include/configs') diff --git a/include/configs/dvlhost.h b/include/configs/dvlhost.h new file mode 100644 index 0000000000..bccd416fcc --- /dev/null +++ b/include/configs/dvlhost.h @@ -0,0 +1,248 @@ +/* + * (C) Copyright 2009 + * Michael Schwingen, michael@schwingen.org + * + * Configuration settings for the + * dLAN200 AV Wireless G ("dvlhost") board. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#define CONFIG_IXP425 1 +#define CONFIG_DVLHOST 1 + +#define CONFIG_DISPLAY_CPUINFO 1 +#define CONFIG_DISPLAY_BOARDINFO 1 + +#define CONFIG_IXP_SERIAL +#define CONFIG_SYS_IXP425_CONSOLE IXP425_UART2 +#define CONFIG_BAUDRATE 115200 +#define CONFIG_BOOTDELAY 3 +#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ +#define CONFIG_BOARD_EARLY_INIT_F 1 +#define CONFIG_SYS_LDSCRIPT "board/dvlhost/u-boot.lds" + +/*************************************************************** + * U-boot generic defines start here. + ***************************************************************/ +/* Size of malloc() pool */ +#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024) + +/* allow to overwrite serial and ethaddr */ +#define CONFIG_ENV_OVERWRITE + +/* Command line configuration. */ +#include + +#define CONFIG_CMD_ELF +#define CONFIG_PCI +#ifdef CONFIG_PCI +#define CONFIG_CMD_PCI +#define CONFIG_PCI_PNP +#define CONFIG_IXP_PCI +#define CONFIG_PCI_SCAN_SHOW +#define CONFIG_CMD_PCI_ENUM +#endif + +#define CONFIG_BOOTCOMMAND "run boot_flash" +/* enable passing of ATAGs */ +#define CONFIG_CMDLINE_TAG 1 +#define CONFIG_SETUP_MEMORY_TAGS 1 +#define CONFIG_INITRD_TAG 1 + +#if defined(CONFIG_CMD_KGDB) +# define CONFIG_KGDB_BAUDRATE 230400 +/* which serial port to use */ +# define CONFIG_KGDB_SER_INDEX 1 +#endif + +/* Miscellaneous configurable options */ +#define CONFIG_SYS_LONGHELP +#define CONFIG_SYS_PROMPT "=> " +/* Console I/O Buffer Size */ +#define CONFIG_SYS_CBSIZE 256 +/* Print Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) +/* max number of command args */ +#define CONFIG_SYS_MAXARGS 16 +/* Boot Argument Buffer Size */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE + +#define CONFIG_SYS_MEMTEST_START 0x00000000 +#define CONFIG_SYS_MEMTEST_END 0x01D80000 + +/* timer clock - 2* OSC_IN system clock */ +#define CONFIG_IXP425_TIMER_CLK 66666666 +#define CONFIG_SYS_HZ 1000 + +/* default load address */ +#define CONFIG_SYS_LOAD_ADDR 0x00010000 + +/* valid baudrates */ +#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, \ + 115200, 230400 } +#define CONFIG_SERIAL_RTS_ACTIVE 1 + +/* + * Stack sizes + * + * The stack sizes are set up in start.S using the settings below + */ +#define CONFIG_STACKSIZE (128*1024) /* regular stack */ + +/* Expansion bus settings */ +#define CONFIG_SYS_EXP_CS0 0xbd113442 + +/* SDRAM settings */ +#define CONFIG_NR_DRAM_BANKS 1 +#define PHYS_SDRAM_1 0x00000000 +#define CONFIG_SYS_SDRAM_BASE 0x00000000 + +/* 32MB SDRAM: 2* 8Mx16, CL3 */ +#define CONFIG_SYS_SDR_CONFIG 0x18 +#define PHYS_SDRAM_1_SIZE 0x02000000 +#define CONFIG_SYS_SDRAM_REFRESH_CNT 0x800 +#define CONFIG_SYS_SDR_MODE_CONFIG 0x1 +#define CONFIG_SYS_DRAM_SIZE PHYS_SDRAM_1_SIZE + +/* FLASH organization: one Spansion S29AL032D-04 Flash */ +#define CONFIG_SYS_TEXT_BASE 0x50000000 +#define CONFIG_SYS_MAX_FLASH_BANKS 1 +/* max number of sectors on one chip */ +#define CONFIG_SYS_MAX_FLASH_SECT 140 +#define PHYS_FLASH_1 0x50000000 +#define CONFIG_SYS_FLASH_BANKS_LIST { PHYS_FLASH_1 } + +#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1 +#define CONFIG_SYS_MONITOR_BASE PHYS_FLASH_1 +#define CONFIG_SYS_MONITOR_LEN (256 << 10) +#define CONFIG_BOARD_SIZE_LIMIT 262144 + +/* Use common CFI driver */ +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_FLASH_CFI_DRIVER +/* no byte writes on IXP4xx */ +#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT + +/* print 'E' for empty sector on flinfo */ +#define CONFIG_SYS_FLASH_EMPTY_INFO + +/* Ethernet */ + +/* include IXP4xx NPE support */ +#define CONFIG_IXP4XX_NPE 1 + +#define CONFIG_NET_MULTI 1 +/* NPE0 PHY: MII dLAN200 AVmodule, 100BaseT-FDX fixed */ +#define CONFIG_PHY_ADDR 0x18 +/* NPE1 PHY: MII IP175 switch, port 5 is host port */ +#define CONFIG_PHY1_ADDR 0x05 +/* MII PHY management */ +#define CONFIG_MII 1 +/* fixed-speed powerline modem without standard PHY registers on MII */ +#define CONFIG_MII_NPE0_FIXEDLINK 1 +#define CONFIG_MII_NPE0_SPEED 100 +#define CONFIG_MII_NPE0_FULLDUPLEX 1 +/* fixed-speed switch without standard PHY registers on MII */ +#define CONFIG_MII_NPE1_FIXEDLINK 1 +#define CONFIG_MII_NPE1_SPEED 100 +#define CONFIG_MII_NPE1_FULLDUPLEX 1 + +/* Number of ethernet rx buffers & descriptors */ +#define CONFIG_SYS_RX_ETH_BUFFER 16 +#define CONFIG_RESET_PHY_R 1 +/* ethernet switch connected to MII port */ +#define CONFIG_MII_ETHSWITCH 1 +#define CONFIG_HAS_ETH1 1 + +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_NET +#define CONFIG_CMD_MII +#define CONFIG_CMD_PING +#undef CONFIG_CMD_NFS + +/* BOOTP options */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME + +/* Cache Configuration */ +#define CONFIG_SYS_CACHELINE_SIZE 32 + +/* + * environment organization: + * one flash sector, embedded in uboot area (bottom bootblock flash) + */ +#define CONFIG_ENV_IS_IN_FLASH 1 +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_ADDR (PHYS_FLASH_1 + 0x4000) +#define CONFIG_SYS_USE_PPCENV 1 + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "npe_ucode=50040000\0" \ + "ethprime=NPE1\0" \ + "ethrotate=no\0" \ + "mtd=IXP4XX-Flash.0:256k(uboot),64k(ucode),1152k(linux),-(root),\0" \ + "kerneladdr=50050000\0" \ + "kernelfile=dvlhost/uImage\0" \ + "rootfile=dvlhost/rootfs\0" \ + "rootaddr=50170000\0" \ + "loadaddr=10000\0" \ + "updateboot_ser=mw.b 10000 ff 40000;" \ + " loady ${loadaddr};" \ + " run eraseboot writeboot\0" \ + "updateboot_net=mw.b 10000 ff 40000;" \ + " tftp ${loadaddr} dvlhost/u-boot.bin;" \ + " run eraseboot writeboot\0" \ + "eraseboot=protect off 50000000 50003fff;" \ + " protect off 50006000 5003ffff;" \ + " erase 50000000 50003fff;" \ + " erase 50006000 5003ffff\0" \ + "writeboot=cp.b 10000 50000000 4000;" \ + " cp.b 16000 50006000 3a000\0" \ + "updateucode=loady;" \ + " era ${npe_ucode} +${filesize};" \ + " cp.b ${loadaddr} ${npe_ucode} ${filesize}\0" \ + "updateroot=tftp ${loadaddr} ${rootfile};" \ + " era ${rootaddr} +${filesize};" \ + " cp.b ${loadaddr} ${rootaddr} ${filesize}\0" \ + "updatekern=tftp ${loadaddr} ${kernelfile};" \ + " era ${kerneladdr} +${filesize};" \ + " cp.b ${loadaddr} ${kerneladdr} ${filesize}\0" \ + "flashargs=setenv bootargs mtdparts=${mtd} root=/dev/mtdblock3" \ + " rootfstype=squashfs,jffs2 init=/etc/preinit\0" \ + "netargs=setenv bootargs mtdparts=${mtd} root=/dev/mtdblock3" \ + " rootfstype=squashfs,jffs2 init=/etc/preinit\0" \ + "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0" \ + "addeth=setenv bootargs ${bootargs} ethaddr=${ethaddr}\0" \ + "boot_flash=run flashargs addtty addeth;" \ + " bootm ${kerneladdr}\0" \ + "boot_net=run netargs addtty addeth;" \ + " tftpboot ${loadaddr} ${kernelfile};" \ + " bootm\0" + +/* additions for new relocation code, must be added to all boards */ +#define CONFIG_SYS_INIT_SP_ADDR \ + (CONFIG_SYS_SDRAM_BASE + 0x1000 - GENERATED_GBL_DATA_SIZE) + +#endif /* __CONFIG_H */ -- cgit From 973af335e61eede3578371330abd3971805887f5 Mon Sep 17 00:00:00 2001 From: Michael Schwingen Date: Mon, 23 May 2011 00:00:10 +0200 Subject: update/fix IXDP425 / IXDPG425 boards Signed-off-by: Michael Schwingen --- include/configs/ixdp425.h | 196 +++++++++++++++++++++++++++++++-------------- include/configs/ixdpg425.h | 11 ++- 2 files changed, 142 insertions(+), 65 deletions(-) (limited to 'include/configs') diff --git a/include/configs/ixdp425.h b/include/configs/ixdp425.h index 28d41e2925..4bad31dfed 100644 --- a/include/configs/ixdp425.h +++ b/include/configs/ixdp425.h @@ -36,12 +36,19 @@ #define CONFIG_DISPLAY_CPUINFO 1 /* display cpu info (and speed) */ #define CONFIG_DISPLAY_BOARDINFO 1 /* display board info */ +/* + * select serial console configuration + */ +#define CONFIG_IXP_SERIAL +#define CONFIG_SYS_IXP425_CONSOLE IXP425_UART1 +#define CONFIG_BAUDRATE 115200 + +#define CONFIG_BOARD_EARLY_INIT_F 1 + /*************************************************************** * U-boot generic defines start here. ***************************************************************/ -#undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */ - /* * Size of malloc() pool */ @@ -50,9 +57,6 @@ /* allow to overwrite serial and ethaddr */ #define CONFIG_ENV_OVERWRITE -#define CONFIG_BAUDRATE 115200 - - /* * BOOTP options */ @@ -61,38 +65,33 @@ #define CONFIG_BOOTP_GATEWAY #define CONFIG_BOOTP_HOSTNAME - -/* - * Command line configuration. - */ +/* Command line configuration. */ #include #define CONFIG_CMD_ELF -#define CONFIG_CMD_PCI - #define CONFIG_PCI +#ifdef CONFIG_PCI +#define CONFIG_CMD_PCI +#define CONFIG_PCI_PNP #define CONFIG_IXP_PCI -#define CONFIG_NET_MULTI +#define CONFIG_PCI_SCAN_SHOW +#define CONFIG_CMD_PCI_ENUM #define CONFIG_EEPRO100 +#endif -#define CONFIG_BOOTDELAY 3 -/*#define CONFIG_ETHADDR 08:00:3e:26:0a:5b*/ -#define CONFIG_NETMASK 255.255.255.0 -#define CONFIG_IPADDR 192.168.0.21 -#define CONFIG_SERVERIP 192.168.0.148 -#define CONFIG_BOOTCOMMAND "bootm 50040000" -#define CONFIG_BOOTARGS "root=/dev/mtdblock2 rootfstype=cramfs console=ttyS0,115200" -#define CONFIG_CMDLINE_TAG +#define CONFIG_BOOTCOMMAND "run boot_flash" +/* enable passing of ATAGs */ +#define CONFIG_CMDLINE_TAG 1 +#define CONFIG_SETUP_MEMORY_TAGS 1 +#define CONFIG_INITRD_TAG 1 #if defined(CONFIG_CMD_KGDB) #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ #endif -/* - * Miscellaneous configurable options - */ +/* Miscellaneous configurable options */ #define CONFIG_SYS_LONGHELP /* undef to save memory */ #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ @@ -103,10 +102,13 @@ #define CONFIG_SYS_MEMTEST_START 0x00400000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x00800000 /* 4 ... 8 MB in DRAM */ -#define CONFIG_SYS_LOAD_ADDR 0x00010000 /* default load address */ +/* timer clock - 2* OSC_IN system clock */ +#define CONFIG_IXP425_TIMER_CLK 66666666 +#define CONFIG_SYS_HZ 1000 + +/* default load address */ +#define CONFIG_SYS_LOAD_ADDR 0x00010000 -#define CONFIG_SYS_HZ 3333333 /* spec says 66.666 MHz, but it appears to be 33 */ - /* valid baudrates */ #define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } /* @@ -115,10 +117,6 @@ * The stack sizes are set up in start.S using the settings below */ #define CONFIG_STACKSIZE (128*1024) /* regular stack */ -#ifdef CONFIG_USE_IRQ -#define CONFIG_STACKSIZE_IRQ (4*1024) /* IRQ stack */ -#define CONFIG_STACKSIZE_FIQ (4*1024) /* FIQ stack */ -#endif /*************************************************************** * Platform/Board specific defines start here. @@ -129,71 +127,145 @@ */ -/* - * select serial console configuration - */ -#define CONFIG_IXP_SERIAL -#define CONFIG_SYS_IXP425_CONSOLE IXP425_UART1 /* we use UART1 for console */ /* * Physical Memory Map */ -#define CONFIG_NR_DRAM_BANKS 1 /* we have 2 banks of DRAM */ -#define PHYS_SDRAM_1 0x00000000 /* SDRAM Bank #1 */ -#define PHYS_SDRAM_1_SIZE 0x01000000 /* 16 MB */ +#define CONFIG_SYS_TEXT_BASE 0x50000000 #define PHYS_FLASH_1 0x50000000 /* Flash Bank #1 */ #define PHYS_FLASH_SIZE 0x00800000 /* 8 MB */ #define PHYS_FLASH_BANK_SIZE 0x00800000 /* 8 MB Banks */ #define PHYS_FLASH_SECT_SIZE 0x00020000 /* 128 KB sectors (x1) */ -#define CONFIG_SYS_DRAM_BASE 0x00000000 -#define CONFIG_SYS_DRAM_SIZE 0x01000000 - #define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE #define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ +#define CONFIG_BOARD_SIZE_LIMIT 262144 -/* - * Expansion bus settings - */ -#define CONFIG_SYS_EXP_CS0 0xbcd23c42 +/* Expansion bus settings */ +#define CONFIG_SYS_EXP_CS0 0xbcd23c42 + +/* SDRAM settings */ +#define CONFIG_NR_DRAM_BANKS 1 /* we have 2 banks of DRAM */ +#define PHYS_SDRAM_1 0x00000000 /* SDRAM Bank #1 */ +#define CONFIG_SYS_SDRAM_BASE 0x00000000 -/* - * SDRAM settings - */ #define CONFIG_SYS_SDR_CONFIG 0xd #define CONFIG_SYS_SDR_MODE_CONFIG 0x1 #define CONFIG_SYS_SDRAM_REFRESH_CNT 0x81a -/* - * GPIO settings - */ - -/* - * FLASH and environment organization - */ /* * FLASH and environment organization */ #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ #define CONFIG_SYS_MAX_FLASH_SECT 128 /* max number of sectors on one chip */ -#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */ -#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */ #define CONFIG_ENV_IS_IN_FLASH 1 #define CONFIG_SYS_FLASH_BANKS_LIST { PHYS_FLASH_1 } -#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT /* no byte writes on IXP4xx */ - #define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ -#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ - #define CONFIG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */ -#define CONFIG_ENV_ADDR (PHYS_FLASH_1 + 0x20000) +#define CONFIG_ENV_ADDR (PHYS_FLASH_1 + 0x40000) #define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ +/* Use common CFI driver */ +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_FLASH_CFI_DRIVER +/* no byte writes on IXP4xx */ +#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT +/* print 'E' for empty sector on flinfo */ +#define CONFIG_SYS_FLASH_EMPTY_INFO + +/* Ethernet */ + +/* include IXP4xx NPE support */ +#define CONFIG_IXP4XX_NPE 1 +#define CONFIG_NET_MULTI 1 +/* NPE0 PHY address */ +#define CONFIG_PHY_ADDR 0 +/* NPE1 PHY address (HW Release E only) */ +#define CONFIG_PHY1_ADDR 1 +/* MII PHY management */ +#define CONFIG_MII 1 +/* Number of ethernet rx buffers & descriptors */ +#define CONFIG_SYS_RX_ETH_BUFFER 16 + +#define CONFIG_HAS_ETH1 1 + +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_NET +#define CONFIG_CMD_MII +#define CONFIG_CMD_PING +#undef CONFIG_CMD_NFS + +/* Cache Configuration */ +#define CONFIG_SYS_CACHELINE_SIZE 32 + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "npe_ucode=50060000\0" \ + "mtd=IXP4XX-Flash.0:256k(uboot),128k(env),128k(ucode),2048k(linux),-(root)\0" \ + "kerneladdr=50080000\0" \ + "kernelfile=ixdp425/uImage\0" \ + "rootfile=ixdp425/rootfs\0" \ + "rootaddr=50280000\0" \ + "loadaddr=10000\0" \ + "updateboot_ser=mw.b 10000 ff 40000;" \ + " loady ${loadaddr};" \ + " run eraseboot writeboot\0" \ + "updateboot_net=mw.b 10000 ff 40000;" \ + " tftp ${loadaddr} ixdp425/u-boot.bin;" \ + " run eraseboot writeboot\0" \ + "eraseboot=protect off 50000000 5003ffff;" \ + " erase 50000000 5003ffff\0" \ + "writeboot=cp.b 10000 50000000 ${filesize}\0" \ + "updateucode=loady;" \ + " era ${npe_ucode} +${filesize};" \ + " cp.b ${loadaddr} ${npe_ucode} ${filesize}\0" \ + "updateroot=tftp ${loadaddr} ${rootfile};" \ + " era ${rootaddr} +${filesize};" \ + " cp.b ${loadaddr} ${rootaddr} ${filesize}\0" \ + "updatekern=tftp ${loadaddr} ${kernelfile};" \ + " era ${kerneladdr} +${filesize};" \ + " cp.b ${loadaddr} ${kerneladdr} ${filesize}\0" \ + "flashargs=setenv bootargs mtdparts=${mtd} root=/dev/mtdblock4" \ + " rootfstype=squashfs,jffs2 init=/etc/preinit\0" \ + "netargs=setenv bootargs mtdparts=${mtd} root=/dev/mtdblock4" \ + " rootfstype=squashfs,jffs2 init=/etc/preinit\0" \ + "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0" \ + "addeth=setenv bootargs ${bootargs} ethaddr=${ethaddr}\0" \ + "boot_flash=run flashargs addtty addeth;" \ + " bootm ${kerneladdr}\0" \ + "boot_net=run netargs addtty addeth;" \ + " tftpboot ${loadaddr} ${kernelfile};" \ + " bootm\0" + +/* additions for new relocation code, must be added to all boards */ +#define CONFIG_SYS_INIT_SP_ADDR \ + (CONFIG_SYS_SDRAM_BASE + 0x1000 - GENERATED_GBL_DATA_SIZE) + + +/* + * GPIO settings + */ +#define CONFIG_SYS_GPIO_UTOPIA_GPIO1 0 +#define CONFIG_SYS_GPIO_UTOPIA_IRQ_N 1 +#define CONFIG_SYS_GPIO_HSS1_IRQ_N 2 +#define CONFIG_SYS_GPIO_HSS0_IRQ_N 3 +#define CONFIG_SYS_GPIO_ETH0_IRQ_N 4 +#define CONFIG_SYS_GPIO_ETH1_IRQ_N 5 +#define CONFIG_SYS_GPIO_I2C_SCL 6 +#define CONFIG_SYS_GPIO_I2C_SDA 7 +#define CONFIG_SYS_GPIO_PCI_INTD_N 8 +#define CONFIG_SYS_GPIO_PCI_INTC_N 9 +#define CONFIG_SYS_GPIO_PCI_INTB_N 10 +#define CONFIG_SYS_GPIO_PCI_INTA_N 11 +#define CONFIG_SYS_GPIO_UTOPIA_GPIO0 12 +#define CONFIG_SYS_GPIO_PCI_RESET_N 13 +#define CONFIG_SYS_GPIO_PCI_CLK 14 +#define CONFIG_SYS_GPIO_EXTBUS_CLK 15 + #endif /* __CONFIG_H */ diff --git a/include/configs/ixdpg425.h b/include/configs/ixdpg425.h index 637fd7d4f8..3de001371f 100644 --- a/include/configs/ixdpg425.h +++ b/include/configs/ixdpg425.h @@ -53,9 +53,6 @@ /* * Misc configuration options */ -#undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */ -#define CONFIG_USE_IRQ 1 /* we need IRQ stuff for timer */ -#define CONFIG_TIMER_IRQ #define CONFIG_BOOTCOUNT_LIMIT /* support for bootcount limit */ #define CONFIG_SYS_BOOTCOUNT_ADDR 0x60003000 /* inside qmrg sram */ @@ -115,6 +112,7 @@ #define CONFIG_SYS_MEMTEST_END 0x00800000 /* 4 ... 8 MB in DRAM */ #define CONFIG_SYS_LOAD_ADDR 0x00010000 /* default load address */ +#define CONFIG_IXP425_TIMER_CLK 66666666 #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ /* valid baudrates */ @@ -179,6 +177,8 @@ #define PHYS_SDRAM_1 0x00000000 /* SDRAM Bank #1 */ #define PHYS_SDRAM_1_SIZE 0x02000000 /* 32 MB */ +#define CONFIG_SYS_TEXT_BASE 0x50000000 + #define PHYS_FLASH_1 0x50000000 /* Flash Bank #1 */ #define PHYS_FLASH_SIZE 0x01000000 /* 16 MB */ #define PHYS_FLASH_BANK_SIZE 0x01000000 /* 16 MB Banks */ @@ -248,4 +248,9 @@ */ #define CONFIG_SYS_CACHELINE_SIZE 32 +/* additions for new relocation code, must be added to all boards */ +#define CONFIG_SYS_SDRAM_BASE 0 +#define CONFIG_SYS_INIT_SP_ADDR \ + (CONFIG_SYS_SDRAM_BASE + 0x1000 - GENERATED_GBL_DATA_SIZE) + #endif /* __CONFIG_H */ -- cgit From 904ec57b3310d09280a0ad32928cbe814160d1eb Mon Sep 17 00:00:00 2001 From: Michael Schwingen Date: Mon, 23 May 2011 00:00:11 +0200 Subject: update/fix PDNB3 board Signed-off-by: Michael Schwingen --- include/configs/pdnb3.h | 10 +++++++--- 1 file changed, 7 insertions(+), 3 deletions(-) (limited to 'include/configs') diff --git a/include/configs/pdnb3.h b/include/configs/pdnb3.h index 33fa6ee8bd..7fe9e5b268 100644 --- a/include/configs/pdnb3.h +++ b/include/configs/pdnb3.h @@ -50,9 +50,6 @@ /* * Misc configuration options */ -#define CONFIG_USE_IRQ 1 /* we need IRQ stuff for timer */ -#define CONFIG_TIMER_IRQ - #define CONFIG_BOOTCOUNT_LIMIT /* support for bootcount limit */ #define CONFIG_SYS_BOOTCOUNT_ADDR 0x60003000 /* inside qmrg sram */ @@ -117,6 +114,7 @@ #define CONFIG_SYS_MEMTEST_END 0x00800000 /* 4 ... 8 MB in DRAM */ #define CONFIG_SYS_LOAD_ADDR 0x00010000 /* default load address */ +#define CONFIG_IXP425_TIMER_CLK 66666666 #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ /* valid baudrates */ #define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } @@ -188,6 +186,7 @@ #define PHYS_SDRAM_1 0x00000000 /* SDRAM Bank #1 */ #define PHYS_SDRAM_1_SIZE 0x02000000 /* 32 MB */ +#define CONFIG_SYS_TEXT_BASE 0x50000000 #define CONFIG_SYS_FLASH_BASE 0x50000000 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE #if defined(CONFIG_SCPU) @@ -345,4 +344,9 @@ */ #define CONFIG_SYS_CACHELINE_SIZE 32 +/* additions for new relocation code, must be added to all boards */ +#define CONFIG_SYS_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_INIT_SP_ADDR \ + (CONFIG_SYS_SDRAM_BASE + 0x1000 - GENERATED_GBL_DATA_SIZE) + #endif /* __CONFIG_H */ -- cgit