From d58a9451e7339ed4cf2b2627e534611f427fb791 Mon Sep 17 00:00:00 2001 From: Wolfgang Denk Date: Tue, 28 Oct 2014 15:44:10 +0100 Subject: ppc/arm: zap EMK boards The following bard configurations have been without active maintenance for a long time, and the board maintainer agrees to have them removed: MPC5200: TOP5200, MINI5200, EVAL5200 MPC860: TOP860 at91sam9xeXXX: top9000eval_xe, top9000su_xe Signed-off-by: Wolfgang Denk Cc: Reinhard Meyer [trini: Add missing Kconfig removals] Signed-off-by: Tom Rini --- include/configs/TOP5200.h | 402 --------------------------------------------- include/configs/TOP860.h | 409 ---------------------------------------------- include/configs/top9000.h | 290 -------------------------------- 3 files changed, 1101 deletions(-) delete mode 100644 include/configs/TOP5200.h delete mode 100644 include/configs/TOP860.h delete mode 100644 include/configs/top9000.h (limited to 'include/configs') diff --git a/include/configs/TOP5200.h b/include/configs/TOP5200.h deleted file mode 100644 index 92128b9588..0000000000 --- a/include/configs/TOP5200.h +++ /dev/null @@ -1,402 +0,0 @@ -/* - * (C) Copyright 2003 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * modified for TOP5200-series by Reinhard Meyer, www.emk-elektronik.de - * - * TOP5200 differences from IceCube: - * 1 FLASH Bank for one Chip only, up to 64 MB in 16 MB Banks - * bank switch controlled by TIMER_6(LSB) and TIMER_7(MSB) Pins - * 1 SDRAM/DDRAM Bank up to 256 MB - * local VPD I2C Bus is software driven and uses - * GPIO_WKUP_6 for SDA, GPIO_WKUP_7 for SCL - * FLASH is re-located at 0xff000000 - * Internal regs are at 0xf0000000 - * Reset jumps to 0x00000100 - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - * (easy to change) - */ - -#define CONFIG_MPC5200 1 /* This is a MPC5200 CPU */ -#define CONFIG_TOP5200 1 /* ... on TOP5200 board - we need this for FEC.C */ - -/* - * allowed and functional CONFIG_SYS_TEXT_BASE values: - * 0xff000000 low boot at 0x00000100 (default board setting) - * 0xfff00000 high boot at 0xfff00100 (board needs modification) - * 0x00100000 RAM load and test - */ -#define CONFIG_SYS_TEXT_BASE 0xff000000 - -#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */ - -#define CONFIG_HIGH_BATS 1 /* High BATs supported */ - -/* - * Serial console configuration - */ -#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */ -#define CONFIG_BAUDRATE 9600 /* ... at 9600 bps */ -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } - - -#if defined (CONFIG_EVAL5200) || defined (CONFIG_LITE5200) -/* - * PCI Mapping: - * 0x40000000 - 0x4fffffff - PCI Memory - * 0x50000000 - 0x50ffffff - PCI IO Space - */ -# define CONFIG_PCI 1 -# define CONFIG_PCI_PNP 1 -# define CONFIG_PCI_SCAN_SHOW 1 -# define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1 - -# define CONFIG_PCI_MEM_BUS 0x40000000 -# define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS -# define CONFIG_PCI_MEM_SIZE 0x10000000 - -# define CONFIG_PCI_IO_BUS 0x50000000 -# define CONFIG_PCI_IO_PHYS CONFIG_PCI_IO_BUS -# define CONFIG_PCI_IO_SIZE 0x01000000 - -#endif - -/* USB */ -#if defined (CONFIG_EVAL5200) || defined (CONFIG_LITE5200) - -# define CONFIG_USB_OHCI -# define CONFIG_USB_CLOCK 0x0001bbbb -# if defined (CONFIG_EVAL5200) -# define CONFIG_USB_CONFIG 0x00005100 -# else -# define CONFIG_USB_CONFIG 0x00001000 -# endif -# define CONFIG_DOS_PARTITION -# define CONFIG_USB_STORAGE - -#endif - -/* IDE */ -#if defined (CONFIG_EVAL5200) || defined (CONFIG_LITE5200) -# define CONFIG_DOS_PARTITION -#endif - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_BEDBUG -#define CONFIG_CMD_DATE -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_ELF -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IMMAP -#define CONFIG_CMD_MII -#define CONFIG_CMD_REGINFO - -#if defined (CONFIG_EVAL5200) || defined (CONFIG_LITE5200) -#define CONFIG_CMD_FAT -#define CONFIG_CMD_IDE -#define CONFIG_CMD_USB -#define CONFIG_CMD_PCI -#endif - - -/* - * MUST be low boot - HIGHBOOT is not supported anymore - */ -#if (CONFIG_SYS_TEXT_BASE == 0xFF000000) /* Boot low with 16 MB Flash */ -# define CONFIG_SYS_LOWBOOT 1 -# define CONFIG_SYS_LOWBOOT16 1 -#else -# error "CONFIG_SYS_TEXT_BASE must be 0xff000000" -#endif - -/* - * Autobooting - */ -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ - -#define CONFIG_PREBOOT "echo;" \ - "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "flash_nfs=run nfsargs addip;" \ - "bootm ${kernel_addr}\0" \ - "flash_self=run ramargs addip;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \ - "rootpath=/opt/eldk/ppc_82xx\0" \ - "bootfile=/tftpboot/MPC5200/uImage\0" \ - "" - -#define CONFIG_BOOTCOMMAND "run flash_self" - -/* - * IPB Bus clocking configuration. - */ -#undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ - -/* - * I2C configuration - */ -/* - * EEPROM configuration - */ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 70 - -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 -#define CONFIG_SYS_EEPROM_SIZE 0x2000 - -#define CONFIG_ENV_OVERWRITE -#define CONFIG_MISC_INIT_R - -#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ - -#if defined(CONFIG_SYS_I2C_SOFT) -# define CONFIG_SYS_I2C -# define CONFIG_SYS_I2C_SOFT_SPEED 100000 -# define CONFIG_SYS_I2C_SOFT_SLAVE 0x7F -/**/ -# define SDA0 0x40 -# define SCL0 0x80 -# define GPIOE0 *((volatile uchar*)(CONFIG_SYS_MBAR+0x0c00)) -# define DDR0 *((volatile uchar*)(CONFIG_SYS_MBAR+0x0c08)) -# define DVO0 *((volatile uchar*)(CONFIG_SYS_MBAR+0x0c0c)) -# define DVI0 *((volatile uchar*)(CONFIG_SYS_MBAR+0x0c20)) -# define ODE0 *((volatile uchar*)(CONFIG_SYS_MBAR+0x0c04)) -# define I2C_INIT {GPIOE0|=(SDA0|SCL0);ODE0|=(SDA0|SCL0);DVO0|=(SDA0|SCL0);DDR0|=(SDA0|SCL0);} -# define I2C_READ ((DVI0&SDA0)?1:0) -# define I2C_SDA(x) {if(x)DVO0|=SDA0;else DVO0&=~SDA0;} -# define I2C_SCL(x) {if(x)DVO0|=SCL0;else DVO0&=~SCL0;} -# define I2C_DELAY {udelay(5);} -# define I2C_ACTIVE {DDR0|=SDA0;} -# define I2C_TRISTATE {DDR0&=~SDA0;} - -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 -#define CONFIG_SYS_I2C_FACT_ADDR 0x57 -#endif - -#if defined (CONFIG_HARD_I2C) -# define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */ -# define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */ -# define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x54 -#define CONFIG_SYS_I2C_FACT_ADDR 0x54 -#endif - -/* - * Flash configuration, expect one 16 Megabyte Bank at most - */ -#define CONFIG_SYS_FLASH_BASE 0xff000000 -#define CONFIG_SYS_FLASH_SIZE 0x01000000 -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of memory banks */ -#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0) - -#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max num of sects on one chip */ - -#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */ - -#undef CONFIG_FLASH_16BIT /* Flash is 8-bit */ - -/* - * DRAM configuration - will be read from VPD later... TODO! - */ -#if 0 -/* 2x MT48LC16M16A2 - 7.0 ns SDRAMS = 64 MegaBytes Total */ -#define CONFIG_SYS_DRAM_DDR 0 -#define CONFIG_SYS_DRAM_EMODE 0 -#define CONFIG_SYS_DRAM_MODE 0x008D -#define CONFIG_SYS_DRAM_CONTROL 0x514F0000 -#define CONFIG_SYS_DRAM_CONFIG1 0xC2233A00 -#define CONFIG_SYS_DRAM_CONFIG2 0x88B70004 -#define CONFIG_SYS_DRAM_TAP_DEL 0x08 -#define CONFIG_SYS_DRAM_RAM_SIZE 0x19 -#endif -#if 1 -/* 2x MT48LC16M16A2 - 7.5 ns SDRAMS = 64 MegaBytes Total */ -#define CONFIG_SYS_DRAM_DDR 0 -#define CONFIG_SYS_DRAM_EMODE 0 -#define CONFIG_SYS_DRAM_MODE 0x00CD -#define CONFIG_SYS_DRAM_CONTROL 0x514F0000 -#define CONFIG_SYS_DRAM_CONFIG1 0xD2333A00 -#define CONFIG_SYS_DRAM_CONFIG2 0x8AD70004 -#define CONFIG_SYS_DRAM_TAP_DEL 0x08 -#define CONFIG_SYS_DRAM_RAM_SIZE 0x19 -#endif - -/* - * Environment settings - */ -#define CONFIG_ENV_IS_IN_EEPROM 1 /* turn on EEPROM env feature */ -#define CONFIG_ENV_OFFSET 0x1000 -#define CONFIG_ENV_SIZE 0x0700 - -/* - * VPD settings - */ -#define CONFIG_SYS_FACT_OFFSET 0x1800 -#define CONFIG_SYS_FACT_SIZE 0x0800 - -/* - * Memory map - * - * Warning!!! with the current BestComm Task, MBAR MUST BE set to 0xf0000000 - */ -#define CONFIG_SYS_MBAR 0xf0000000 /* DO NOT CHANGE this */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_DEFAULT_MBAR 0x80000000 - -/* Use SRAM until RAM will be available */ -#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM -#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE /* Size of used area in DPRAM */ - - -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE -#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) -# define CONFIG_SYS_RAMBOOT 1 -#endif - -#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ -#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/* - * Ethernet configuration - */ -#define CONFIG_MPC5xxx_FEC 1 -#define CONFIG_MPC5xxx_FEC_MII10 /* Workaround for FEC 100Mbit problem */ -#define CONFIG_PHY_ADDR 0x1f -#define CONFIG_PHY_TYPE 0x79c874 -/* - * GPIO configuration: - * PSC1,2,3 predefined as UART - * PCI disabled - * Ethernet 100 with MD - */ -#define CONFIG_SYS_GPS_PORT_CONFIG 0x00058044 - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#if defined(CONFIG_CMD_KGDB) -# define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -# define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x01f00000 /* 1 ... 31 MB in DRAM */ - -#define CONFIG_SYS_LOAD_ADDR 0x200000 /* default load address */ - -#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ -#if defined(CONFIG_CMD_KGDB) -# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - - -#ifdef CONFIG_EVAL5200 /* M48T08 is available with the Evaluation board only */ - #define CONFIG_RTC_MK48T59 1 /* use M48T08 on EVAL5200 */ - #define RTC(reg) (0xf0010000+reg) - /* setup CS2 for M48T08. Must MAP 64kB */ - #define CONFIG_SYS_CS2_START RTC(0) - #define CONFIG_SYS_CS2_SIZE 0x10000 - /* setup CS2 configuration register: */ - /* WaitP = 0, WaitX = 4, MX=0, AL=1, AA=1, CE=1 */ - /* AS=2, DS=0, Bank=0, WTyp=0, WS=0, RS=0, WO=0, RO=0 */ - #define CONFIG_SYS_CS2_CFG 0x00047800 -#else - #define CONFIG_RTC_MPC5200 1 /* use internal MPC5200 RTC */ -#endif - -/* - * Various low-level settings - */ -#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI -#define CONFIG_SYS_HID0_FINAL HID0_ICE - -#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE -#define CONFIG_SYS_BOOTCS_CFG 0x00047801 -#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE - -#define CONFIG_SYS_CS_BURST 0x00000000 -#define CONFIG_SYS_CS_DEADCYCLE 0x33333333 - -#define CONFIG_SYS_RESET_ADDRESS 0x7f000000 - -/*----------------------------------------------------------------------- - * IDE/ATA stuff Supports IDE harddisk - *----------------------------------------------------------------------- - */ - -#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */ - -#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ -#undef CONFIG_IDE_LED /* LED for ide not supported */ - -#define CONFIG_IDE_RESET 1 -#define CONFIG_IDE_PREINIT - -#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */ -#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */ - -#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 - -#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA - -/* Offset for data I/O */ -#define CONFIG_SYS_ATA_DATA_OFFSET (0x0060) - -/* Offset for normal register accesses */ -#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET) - -/* Offset for alternate registers */ -#define CONFIG_SYS_ATA_ALT_OFFSET (0x005c) - -/* Interval between registers */ -#define CONFIG_SYS_ATA_STRIDE 4 - -#endif /* __CONFIG_H */ diff --git a/include/configs/TOP860.h b/include/configs/TOP860.h deleted file mode 100644 index da68503a69..0000000000 --- a/include/configs/TOP860.h +++ /dev/null @@ -1,409 +0,0 @@ -/* - * (C) Copyright 2003 - * EMK Elektronik GmbH - * Reinhard Meyer - * - * Configuation settings for the TOP860 board. - * - * ----------------------------------------------------------------- - * SPDX-License-Identifier: GPL-2.0+ - */ -/* - * TOP860 is a simple module: - * 16-bit wide FLASH on CS0 (2MB or more) - * 32-bit wide DRAM on CS2 (either 4MB or 16MB) - * FEC with Am79C874 100-Base-T and Fiber Optic - * Ports available, but we choose SMC1 for Console - * 8k I2C EEPROM at address 0xae, 6k user available, 2k factory set - * 32768Hz crystal PLL set for 49.152MHz Core and 24.576MHz Bus Clock - * - * This config has been copied from MBX.h / MBX860T.h - */ -/* - * board/config.h - configuration options, board specific - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - * (easy to change) - */ - -/*----------------------------------------------------------------------- - * CPU and BOARD type - */ -#define CONFIG_MPC860 1 /* This is a MPC860 CPU */ -#define CONFIG_MPC860T 1 /* even better... an FEC! */ -#define CONFIG_TOP860 1 /* ...on a TOP860 module */ - -#define CONFIG_SYS_TEXT_BASE 0x80000000 - -#undef CONFIG_WATCHDOG /* watchdog disabled */ -#define CONFIG_IDENT_STRING " EMK TOP860" - -/*----------------------------------------------------------------------- - * CLOCK settings - */ -#define CONFIG_SYSCLK 49152000 -#define CONFIG_SYS_XTAL 32768 -#define CONFIG_EBDF 1 -#define CONFIG_COM 3 -#define CONFIG_RTC_MPC8xx - -/*----------------------------------------------------------------------- - * Physical memory map as defined by EMK - */ -#define CONFIG_SYS_IMMR 0xFFF00000 /* Internal Memory Mapped Register */ -#define CONFIG_SYS_FLASH_BASE 0x80000000 /* FLASH in final mapping */ -#define CONFIG_SYS_DRAM_BASE 0x00000000 /* DRAM in final mapping */ -#define CONFIG_SYS_FLASH_MAX 0x00400000 /* max FLASH to expect */ -#define CONFIG_SYS_DRAM_MAX 0x01000000 /* max DRAM to expect */ - -/*----------------------------------------------------------------------- - * derived values - */ -#define CONFIG_SYS_MF (CONFIG_SYSCLK/CONFIG_SYS_XTAL) -#define CONFIG_SYS_CPUCLOCK CONFIG_SYSCLK -#define CONFIG_SYS_BRGCLOCK CONFIG_SYSCLK -#define CONFIG_SYS_BUSCLOCK (CONFIG_SYSCLK >> CONFIG_EBDF) -#define CONFIG_8xx_GCLK_FREQ CONFIG_SYSCLK - -/*----------------------------------------------------------------------- - * FLASH organization - */ -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max number of sectors on one chip */ - -#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ - -#define CONFIG_SYS_FLASH_CFI - -/*----------------------------------------------------------------------- - * Command interpreter - */ -#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */ -#undef CONFIG_8xx_CONS_SMC2 -#define CONFIG_BAUDRATE 9600 - -/* - * Allow partial commands to be matched to uniqueness. - */ -#define CONFIG_SYS_MATCH_PARTIAL_CMD - - -/* - * Command line configuration. - */ -#include - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_I2C -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_REGINFO -#define CONFIG_CMD_IMMAP -#define CONFIG_CMD_ELF -#define CONFIG_CMD_DATE -#define CONFIG_CMD_MII -#define CONFIG_CMD_BEDBUG - - -#define CONFIG_SOURCE 1 -#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 -#undef CONFIG_LOADS_ECHO /* NO echo on for serial download */ - - -#define CONFIG_SYS_LONGHELP /* undef to save memory */ - -#undef CONFIG_SYS_HUSH_PARSER /* Hush parse for U-Boot */ - - -#if defined(CONFIG_CMD_KGDB) - #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else - #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif - -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -/*----------------------------------------------------------------------- - * Memory Test Command - */ -#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -/*----------------------------------------------------------------------- - * Environment handler - * only the first 6k in EEPROM are available for user. Of that we use 256b - */ -#define CONFIG_ENV_IS_IN_EEPROM 1 /* turn on EEPROM env feature */ -#define CONFIG_ENV_OFFSET 0x1000 -#define CONFIG_ENV_SIZE 0x0700 -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 -#define CONFIG_SYS_FACT_OFFSET 0x1800 -#define CONFIG_SYS_FACT_SIZE 0x0800 -#define CONFIG_SYS_I2C_FACT_ADDR 0x57 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 -#define CONFIG_SYS_EEPROM_SIZE 0x2000 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 12 -#define CONFIG_ENV_OVERWRITE -#define CONFIG_MISC_INIT_R - -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ -#define CONFIG_SYS_I2C_SOFT_SPEED 100000 -#define CONFIG_SYS_I2C_SOFT_SLAVE 0xFE -/**/ -#define SDA 0x00010 -#define SCL 0x00020 -#define __I2C_DIR immr->im_cpm.cp_pbdir -#define __I2C_DAT immr->im_cpm.cp_pbdat -#define __I2C_PAR immr->im_cpm.cp_pbpar -#define __I2C_ODR immr->im_cpm.cp_pbodr -#define I2C_INIT { __I2C_PAR &= ~(SDA|SCL); \ - __I2C_ODR &= ~(SDA|SCL); \ - __I2C_DAT |= (SDA|SCL); \ - __I2C_DIR|=(SDA|SCL); } -#define I2C_READ ((__I2C_DAT & SDA) ? 1 : 0) -#define I2C_SDA(x) { if (x) __I2C_DAT |= SDA; else __I2C_DAT &= ~SDA; } -#define I2C_SCL(x) { if (x) __I2C_DAT |= SCL; else __I2C_DAT &= ~SCL; } -#define I2C_DELAY { udelay(5); } -#define I2C_ACTIVE { __I2C_DIR |= SDA; } -#define I2C_TRISTATE { __I2C_DIR &= ~SDA; } - -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } - -/*----------------------------------------------------------------------- - * defines we need to get FEC running - */ -#define CONFIG_FEC_ENET 1 /* Ethernet only via FEC */ -#define FEC_ENET 1 /* eth.c needs it that way... */ -#define CONFIG_SYS_DISCOVER_PHY 1 -#define CONFIG_MII 1 -#define CONFIG_MII_INIT 1 -#define CONFIG_PHY_ADDR 31 - -/*----------------------------------------------------------------------- - * adresses - */ -#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE -#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ - -/*----------------------------------------------------------------------- - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_FLASH_BASE 0x80000000 - -/*----------------------------------------------------------------------- - * Definitions for initial stack pointer and data area (in DPRAM) - */ -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR -#define CONFIG_SYS_INIT_RAM_SIZE 0x2f00 /* Size of used area in DPRAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_VPD_SIZE 256 /* size in bytes reserved for vpd buffer */ -#define CONFIG_SYS_INIT_VPD_OFFSET (CONFIG_SYS_GBL_DATA_OFFSET - CONFIG_SYS_INIT_VPD_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_INIT_VPD_OFFSET-8) - -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */ -#endif - -/* Interrupt level assignments. -*/ -#define FEC_INTERRUPT SIU_LEVEL1 /* FEC interrupt */ - -/*----------------------------------------------------------------------- - * Debug Enable Register - *----------------------------------------------------------------------- - * - */ -#define CONFIG_SYS_DER 0 /* used in start.S */ - -/*----------------------------------------------------------------------- - * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30 - *----------------------------------------------------------------------- - * set up PLPRCR (PLL, Low-Power, and Reset Control Register) - * 12 MF calculated Multiplication factor - * 4 0 0000 - * 1 SPLSS 0 System PLL lock status sticky - * 1 TEXPS 1 Timer expired status - * 1 0 0 - * 1 TMIST 0 Timers interrupt status - * 1 0 0 - * 1 CSRC 0 Clock source (0=DFNH, 1=DFNL) - * 2 LPM 00 Low-power modes - * 1 CSR 0 Checkstop reset enable - * 1 LOLRE 0 Loss-of-lock reset enable - * 1 FIOPD 0 Force I/O pull down - * 5 0 00000 - */ -#define CONFIG_SYS_PLPRCR (PLPRCR_TEXPS | ((CONFIG_SYS_MF-1)<<20)) - -/*----------------------------------------------------------------------- - * SYPCR - System Protection Control 11-9 - * SYPCR can only be written once after reset! - *----------------------------------------------------------------------- - * set up SYPCR: - * 16 SWTC 0xffff Software watchdog timer count - * 8 BMT 0xff Bus monitor timing - * 1 BME 1 Bus monitor enable - * 3 0 000 - * 1 SWF 1 Software watchdog freeze - * 1 SWE 0/1 Software watchdog enable - * 1 SWRI 0/1 Software watchdog reset/interrupt select (1=HRESET) - * 1 SWP 0/1 Software watchdog prescale (1=/2048) - */ -#if defined (CONFIG_WATCHDOG) - #define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ - SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) -#else - #define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF) -#endif - -/*----------------------------------------------------------------------- - * SIUMCR - SIU Module Configuration 11-6 - *----------------------------------------------------------------------- - * set up SIUMCR - * 1 EARB 0 External arbitration - * 3 EARP 000 External arbitration request priority - * 4 0 0000 - * 1 DSHW 0 Data show cycles - * 2 DBGC 00 Debug pin configuration - * 2 DBPC 00 Debug port pins configuration - * 1 0 0 - * 1 FRC 0 FRZ pin configuration - * 1 DLK 0 Debug register lock - * 1 OPAR 0 Odd parity - * 1 PNCS 0 Parity enable for non memory controller regions - * 1 DPC 0 Data parity pins configuration - * 1 MPRE 0 Multiprocessor reservation enable - * 2 MLRC 11 Multi level reservation control (00=IRQ4, 01=3State, 10=KR/RETRY, 11=SPKROUT) - * 1 AEME 0 Async external master enable - * 1 SEME 0 Sync external master enable - * 1 BSC 0 Byte strobe configuration - * 1 GB5E 0 GPL_B5 enable - * 1 B2DD 0 Bank 2 double drive - * 1 B3DD 0 Bank 3 double drive - * 4 0 0000 - */ -#define CONFIG_SYS_SIUMCR (SIUMCR_MLRC11) - -/*----------------------------------------------------------------------- - * TBSCR - Time Base Status and Control 11-26 - *----------------------------------------------------------------------- - * Clear Reference Interrupt Status, Timebase freezing enabled - */ -#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF) - -/*----------------------------------------------------------------------- - * PISCR - Periodic Interrupt Status and Control 11-31 - *----------------------------------------------------------------------- - * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled - */ -#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF | PISCR_PTE) - -/*----------------------------------------------------------------------- - * SCCR - System Clock and reset Control Register 15-27 - *----------------------------------------------------------------------- - * set up SCCR (System Clock and Reset Control Register) - * 1 0 0 - * 2 COM 11 Clock output module (00=full, 01=half, 11=off) - * 3 0 000 - * 1 TBS 1 Timebase source (0=OSCCLK, 1=GCLK2) - * 1 RTDIV 0 Real-time clock divide (0=/4, 1=/512) - * 1 RTSEL 0 Real-time clock select (0=OSCM, 1=EXTCLK) - * 1 CRQEN 0 CPM request enable - * 1 PRQEN 0 Power management request enable - * 2 0 00 - * 2 EBDF xx External bus division factor - * 2 0 00 - * 2 DFSYNC 00 Division factor for SYNCLK - * 2 DFBRG 00 Division factor for BRGCLK - * 3 DFNL 000 Division factor low frequency - * 3 DFNH 000 Division factor high frequency - * 5 0 00000 - */ -#define SCCR_MASK 0 -#ifdef CONFIG_EBDF - #define CONFIG_SYS_SCCR (SCCR_COM11 | SCCR_TBS | SCCR_EBDF01) -#else - #define CONFIG_SYS_SCCR (SCCR_COM11 | SCCR_TBS) -#endif - -/*----------------------------------------------------------------------- - * Chip Select 0 - FLASH - *----------------------------------------------------------------------- - * Preliminary Values - */ -/* FLASH timing: CSNT=1 ACS=10 BIH=1 SCY=4 SETA=0 TLRX=1 EHTR=1 */ -#define CONFIG_SYS_OR_TIMING_FLASH (OR_CSNT_SAM | OR_ACS_DIV4 | OR_BI | OR_SCY_4_CLK | OR_TRLX | OR_EHTR) -#define CONFIG_SYS_OR0_PRELIM (-CONFIG_SYS_FLASH_MAX | CONFIG_SYS_OR_TIMING_FLASH) -#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | BR_PS_16 | BR_V ) - -/*----------------------------------------------------------------------- - * misc - *----------------------------------------------------------------------- - * - */ -/* - * Set the autoboot delay in seconds. A delay of -1 disables autoboot - */ -#define CONFIG_BOOTDELAY 5 - -/* - * Pass the clock frequency to the Linux kernel in units of MHz - */ -#define CONFIG_CLOCKS_IN_MHZ - -#define CONFIG_PREBOOT \ - "echo;echo" - -#undef CONFIG_BOOTARGS -#define CONFIG_BOOTCOMMAND \ - "bootp;" \ - "setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; " \ - "bootm" - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_SUBNETMASK -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_BOOTFILESIZE - - -/* - * Set default IP stuff just to get bootstrap entries into the - * environment so that we can source the full default environment. - */ -#define CONFIG_ETHADDR 9a:52:63:15:85:25 -#define CONFIG_SERVERIP 10.0.4.200 -#define CONFIG_IPADDR 10.0.4.111 - -#define CONFIG_SYS_LOAD_ADDR 0x00100000 /* default load address */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -#endif /* __CONFIG_H */ diff --git a/include/configs/top9000.h b/include/configs/top9000.h deleted file mode 100644 index a96a9cb416..0000000000 --- a/include/configs/top9000.h +++ /dev/null @@ -1,290 +0,0 @@ -/* - * (C) Copyright 2010 - * Reinhard Meyer, EMK Elektronik, reinhard.meyer@emk-elektronik.de - * - * Configuation settings for the TOP9000 CPU module with AT91SAM9XE. - * - * SPDX-License-Identifier: GPL-2.0+ - */ -/* - * top9000 with at91sam9xe256 or at91sam9xe512 - * - * Initial Bootloader is in embedded flash. - * Vital Product Data, U-Boot Environment are in I2C-EEPROM. - * U-Boot is in embedded flash, a backup U-Boot can be in NAND flash. - * kernel and file system are either in NAND flash or on a micro SD card. - * NAND flash is optional. - * I2C EEPROM is never optional. - * SPI FRAM is optional. - * SPI ENC28J60 is optional. - * 16 or 32 bit wide SDRAM. - */ -#ifndef __CONFIG_H -#define __CONFIG_H - -/* SoC must be defined first, before hardware.h is included */ -#define CONFIG_AT91SAM9XE -#include - -/* - * Warning: changing CONFIG_SYS_TEXT_BASE requires - * adapting the initial boot program. - */ -#define CONFIG_SYS_TEXT_BASE 0x20000000 /* start of SDRAM */ - -/* Command line configuration */ -#include -#undef CONFIG_CMD_FPGA -#undef CONFIG_CMD_SETGETDCR -#undef CONFIG_CMD_XIMG -#define CONFIG_CMD_ASKENV -#define CONFIG_SYS_CBSIZE 256 -#define CONFIG_SYS_MAXARGS 16 -#define CONFIG_SYS_PBSIZE \ - (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) -#define CONFIG_SYS_PROMPT "TOP9000> " -#define CONFIG_SYS_LONGHELP -#define CONFIG_CMDLINE_EDITING -#define CONFIG_CMD_BDI -#define CONFIG_CMD_CACHE - -/* ARM asynchronous clock */ -#define CONFIG_SYS_AT91_SLOW_CLOCK 32768 /* slow clock xtal */ -#define CONFIG_SYS_AT91_MAIN_CLOCK 18432000 /* main clock xtal */ - -/* Misc CPU related */ -#define CONFIG_ARCH_CPU_INIT -#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */ -#define CONFIG_SETUP_MEMORY_TAGS -#define CONFIG_INITRD_TAG -#define CONFIG_SKIP_LOWLEVEL_INIT -#define CONFIG_BOARD_EARLY_INIT_F -#define CONFIG_DISPLAY_CPUINFO -#define CONFIG_AT91RESET_EXTRST /* assert external reset */ - -/* general purpose I/O */ -#define CONFIG_ATMEL_LEGACY /* required until (g)pio is fixed */ -#define CONFIG_AT91_GPIO -#define CONFIG_AT91_GPIO_PULLUP 1 /* keep pullups on peripheral pins */ - -/* serial console */ -#define CONFIG_ATMEL_USART -#define CONFIG_USART_BASE ATMEL_BASE_DBGU -#define CONFIG_USART_ID ATMEL_ID_SYS -#define CONFIG_BAUDRATE 115200 - -/* SD/MMC card */ -#define CONFIG_MMC -#define CONFIG_GENERIC_MMC -#define CONFIG_GENERIC_ATMEL_MCI -#define CONFIG_SYS_MMC_CD_PIN AT91_PIN_PC9 -#define CONFIG_CMD_MMC - -/* Ethernet */ -#define CONFIG_MACB -#define CONFIG_SYS_PHY_ID 1 -#define CONFIG_RMII -#define CONFIG_NET_RETRY_COUNT 20 - -/* real time clock */ -#define CONFIG_RTC_AT91SAM9_RTT -#define CONFIG_CMD_DATE - -#if defined(CONFIG_AT91SAM9XE) -/* - * NOR flash - use embedded flash of SAM9XE256/512 - * U-Boot will not fit into 128K ! - * 2010.09 will not fit into 256K with all options enabled ! - * - * Layout: - * 16kB 1st Bootloader - * Rest U-Boot - * the first sector (16kB) of EFLASH cannot be unprotected - * with u-boot commands - */ -# define CONFIG_AT91_EFLASH -# define CONFIG_SYS_FLASH_BASE ATMEL_BASE_FLASH -# define CONFIG_SYS_MAX_FLASH_SECT 32 -# define CONFIG_SYS_MAX_FLASH_BANKS 1 -# define CONFIG_SYS_FLASH_PROTECTION -# define CONFIG_EFLASH_PROTSECTORS 1 /* protect first sector */ -#endif - -/* SPI */ -#define CONFIG_ATMEL_SPI -#define CONFIG_CMD_SPI - -/* RAMTRON FRAM */ -#define CONFIG_CMD_SF -#define CONFIG_ATMEL_SPI0 /* SPI used for FRAM is SPI0 */ -#define FRAM_SPI_BUS 0 -#define FRAM_CS_NUM 0 -#define CONFIG_SPI_FRAM_RAMTRON -#define CONFIG_SF_DEFAULT_SPEED 1000000 /* be conservative here... */ -#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0 -#define CONFIG_SPI_FRAM_RAMTRON_NON_JEDEC "FM25H20" - -/* Microchip ENC28J60 (second LAN) */ -#if defined(CONFIG_EVAL9000) -# define CONFIG_ENC28J60 -# define CONFIG_ATMEL_SPI1 /* SPI used for ENC28J60 is SPI1 */ -# define ENC_SPI_BUS 1 -# define ENC_CS_NUM 0 -# define ENC_SPI_CLOCK 1000000 -#endif /* CONFIG_EVAL9000 */ - -/* - * SDRAM: 1 bank, min 32, max 128 MB - * Initialized before u-boot gets started. - */ -#define CONFIG_NR_DRAM_BANKS 1 -#define CONFIG_SYS_SDRAM_BASE ATMEL_BASE_CS1 -#define CONFIG_SYS_SDRAM_SIZE 0x08000000 -#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE -#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_SDRAM_BASE + 0x01e00000) -#define CONFIG_SYS_LOAD_ADDR \ - (CONFIG_SYS_SDRAM_BASE + 0x01000000) -/* - * Initial stack pointer: 16k - GENERATED_GBL_DATA_SIZE in internal SRAM, - * leaving the correct space for initial global data structure above - * that address while providing maximum stack area below. - */ -#define CONFIG_SYS_INIT_SP_ADDR \ - (ATMEL_BASE_SRAM + 0x4000 - GENERATED_GBL_DATA_SIZE) - -/* - * NAND flash: 256 MB (optional) - * - * Layout: - * 640kB: u-boot (includes space for spare sectors, handled by - * initial loader) - * 2MB: kernel - * rest: file system - */ -#define CONFIG_NAND_ATMEL -#define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define CONFIG_SYS_NAND_BASE ATMEL_BASE_CS3 -#define CONFIG_SYS_NAND_DBW_8 -#define CONFIG_SYS_NAND_MASK_ALE (1 << 21) -#define CONFIG_SYS_NAND_MASK_CLE (1 << 22) -#define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIN_PC14 -#define CONFIG_SYS_NAND_READY_PIN AT91_PIN_PC13 -#define CONFIG_CMD_NAND - -/* USB */ -#define CONFIG_USB_ATMEL -#define CONFIG_USB_ATMEL_CLK_SEL_PLLB -#define CONFIG_USB_OHCI_NEW -#define CONFIG_DOS_PARTITION -#define CONFIG_SYS_USB_OHCI_CPU_INIT -#define CONFIG_SYS_USB_OHCI_REGS_BASE ATMEL_UHP_BASE -#define CONFIG_SYS_USB_OHCI_SLOT_NAME "top9000" -#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2 -#define CONFIG_USB_STORAGE -#define CONFIG_CMD_USB - -/* I2C support must always be enabled */ -#define CONFIG_CMD_I2C -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ -#define CONFIG_SYS_I2C_SOFT_SPEED 400000 -#define CONFIG_SYS_I2C_SOFT_SLAVE 0x7F - -#define I2C0_PORT AT91_PIO_PORTA -#define SDA0_PIN 23 -#define SCL0_PIN 24 -#define I2C1_PORT AT91_PIO_PORTB -#define SDA1_PIN 12 -#define SCL1_PIN 13 -#define I2C_SOFT_DECLARATIONS void iic_init(void);\ - int iic_read(void);\ - void iic_sda(int);\ - void iic_scl(int); -#define I2C_ACTIVE -#define I2C_TRISTATE -#define I2C_INIT iic_init() -#define I2C_READ iic_read() -#define I2C_SDA(bit) iic_sda(bit) -#define I2C_SCL(bit) iic_scl(bit) -#define I2C_DELAY udelay(3) -/* EEPROM configuration */ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 -#define CONFIG_SYS_EEPROM_SIZE 0x2000 -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 -/* later: #define CONFIG_I2C_ENV_EEPROM_BUS 0 */ -/* ENV is always in I2C-EEPROM */ -#define CONFIG_ENV_IS_IN_EEPROM -#define CONFIG_ENV_OFFSET 0x1000 -#define CONFIG_ENV_SIZE 0x0f00 -/* VPD settings */ -#define CONFIG_SYS_I2C_FACT_ADDR 0x57 -#define CONFIG_SYS_FACT_OFFSET 0x1F00 -#define CONFIG_SYS_FACT_SIZE 0x0100 -/* later: #define CONFIG_MISC_INIT_R */ -/* define the next only if you want to allow users to enter VPD data */ -#define CONFIG_SYS_FACT_ENTRY -#ifndef __ASSEMBLY__ -extern void read_factory_r(void); -#endif - -/* - * Only interrupt autoboot if is pressed. Otherwise, garbage - * data on the serial line may interrupt the boot sequence. - */ -#define CONFIG_BOOTDELAY 1 -#define CONFIG_AUTOBOOT -#define CONFIG_AUTOBOOT_KEYED -#define CONFIG_AUTOBOOT_PROMPT \ - "Press SPACE to abort autoboot in %d seconds\n", bootdelay -#define CONFIG_AUTOBOOT_DELAY_STR "d" -#define CONFIG_AUTOBOOT_STOP_STR " " - -/* - * add filesystem commands if we have at least 1 storage - * media with filesystem - */ -#if defined(CONFIG_NAND_ATMEL) \ - || defined(CONFIG_USB_ATMEL) \ - || defined(CONFIG_MMC) -# define CONFIG_DOS_PARTITION -# define CONFIG_CMD_FAT -# define CONFIG_CMD_EXT2 -/* later: #define CONFIG_CMD_JFFS2 */ -#endif - -/* add NET commands if we have at least 1 LAN */ -#if defined(CONFIG_MACB) || defined(CONFIG_ENC28J60) -# define CONFIG_CMD_PING -# define CONFIG_CMD_DHCP -# define CONFIG_CMD_MII -/* is this really needed ? */ -# define CONFIG_RESET_PHY_R -/* BOOTP options */ -# define CONFIG_BOOTP_BOOTFILESIZE -# define CONFIG_BOOTP_BOOTPATH -# define CONFIG_BOOTP_GATEWAY -# define CONFIG_BOOTP_HOSTNAME -#endif - -/* linux in NAND flash */ -#define CONFIG_BOOTCOUNT_LIMIT 1 -#define CONFIG_BOOTCOMMAND \ - "nand read 0x21000000 0xA0000 0x200000; bootm" -#define CONFIG_BOOTARGS \ - "console=ttyS0,115200 " \ - "root=/dev/mtdblock2 " \ - "mtdparts=atmel_nand:" \ - "640k(uboot)ro," \ - "2M(linux)," \ - "16M(root)," \ - "-(rest) " \ - "rw "\ - "rootfstype=jffs2" - -/* Size of malloc() pool */ -#define CONFIG_SYS_MALLOC_LEN \ - ROUND(3 * CONFIG_ENV_SIZE + 128*1024, 0x1000) - -#endif -- cgit