From b7be63abec45858c044f0fbd6aeef524c4663f9b Mon Sep 17 00:00:00 2001 From: Valeriy Glushkov Date: Wed, 4 Feb 2009 18:27:49 +0200 Subject: MPC8349ITX: several config issues fixed The previous version rebooted forever with DDR bigger than 256MB. Access the DS1339 RTC chip is on I2C1 bus. Allow DHCP. Signed-off-by: Valeriy Glushkov Signed-off-by: Kim Phillips --- include/configs/MPC8349ITX.h | 5 +++++ 1 file changed, 5 insertions(+) (limited to 'include') diff --git a/include/configs/MPC8349ITX.h b/include/configs/MPC8349ITX.h index 5e1ddaedd6..38a7386d09 100644 --- a/include/configs/MPC8349ITX.h +++ b/include/configs/MPC8349ITX.h @@ -99,6 +99,7 @@ #define CONFIG_SYS_I2C_OFFSET 0x3000 #define CONFIG_SYS_I2C2_OFFSET 0x3100 #define CONFIG_SYS_SPD_BUS_NUM 1 /* The I2C bus for SPD */ +#define CONFIG_SYS_RTC_BUS_NUM 1 /* The I2C bus for RTC */ #define CONFIG_SYS_I2C_8574_ADDR1 0x20 /* I2C1, PCF8574 */ #define CONFIG_SYS_I2C_8574_ADDR2 0x21 /* I2C1, PCF8574 */ @@ -168,6 +169,9 @@ #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN | \ DDR_SDRAM_CLK_CNTL_CLK_ADJUST_075) +#define CONFIG_VERY_BIG_RAM +#define CONFIG_MAX_MEM_MAPPED ((phys_size_t)256 << 20) + #ifdef CONFIG_HARD_I2C #define CONFIG_SPD_EEPROM /* use SPD EEPROM for DDR setup*/ #endif @@ -457,6 +461,7 @@ boards, we say we have two, but don't display a message if we find only one. */ #define CONFIG_CMD_IRQ #define CONFIG_CMD_NET #define CONFIG_CMD_PING +#define CONFIG_CMD_DHCP #define CONFIG_CMD_SDRAM #if defined(CONFIG_COMPACT_FLASH) || defined(CONFIG_SATA_SIL3114) -- cgit From 19f0e93041dbfe22f8d39b98e4f7f9ea87b77803 Mon Sep 17 00:00:00 2001 From: Heiko Schocher Date: Tue, 24 Feb 2009 11:30:34 +0100 Subject: 83xx, kmeter1: add I2C, dtt, eeprom support This patch adds I2C support for the Keymile kmeter1 board. It uses the First I2C Controller from the CPU, for accessing 4 temperature sensors, an eeprom with IVM data and the booteeprom over a pca9547 mux. Signed-off-by: Heiko Schocher Signed-off-by: Kim Phillips --- include/configs/keymile-common.h | 7 ------- include/configs/kmeter1.h | 35 +++++++++++++++++++++++++++++++++++ 2 files changed, 35 insertions(+), 7 deletions(-) (limited to 'include') diff --git a/include/configs/keymile-common.h b/include/configs/keymile-common.h index d70bc48082..c7f6ba34d4 100644 --- a/include/configs/keymile-common.h +++ b/include/configs/keymile-common.h @@ -42,13 +42,9 @@ #define CONFIG_CMD_IMMAP #define CONFIG_CMD_MII #define CONFIG_CMD_PING - -/* should go away, if kmeter I2C support is enabled */ -#if defined(CONFIG_MGCOGE) || defined(CONFIG_MGSUVD) #define CONFIG_CMD_DTT #define CONFIG_CMD_EEPROM #define CONFIG_CMD_I2C -#endif #undef CONFIG_WATCHDOG /* disable platform specific watchdog */ @@ -73,10 +69,7 @@ #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -/* should go away, if kmeter I2C support is enabled */ -#if defined(CONFIG_MGCOGE) || defined(CONFIG_MGSUVD) #define CONFIG_HUSH_INIT_VAR 1 -#endif #define CONFIG_SYS_ALT_MEMTEST /* memory test, takes time */ #define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ diff --git a/include/configs/kmeter1.h b/include/configs/kmeter1.h index b86c61d5ff..a23c9edb5f 100644 --- a/include/configs/kmeter1.h +++ b/include/configs/kmeter1.h @@ -32,6 +32,7 @@ /* include common defines/options for all Keymile boards */ #include "keymile-common.h" +#define CONFIG_MISC_INIT_R 1 /* * System Clock Setup */ @@ -300,6 +301,38 @@ #define CONFIG_ENV_SIZE 0x2000 #endif /* CFG_RAMBOOT */ +/* I2C */ +#define CONFIG_HARD_I2C /* I2C with hardware support */ +#undef CONFIG_SOFT_I2C /* I2C bit-banged */ +#define CONFIG_FSL_I2C +#define CONFIG_SYS_I2C_SPEED 200000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C_OFFSET 0x3000 +#define CONFIG_I2C_MULTI_BUS 1 +#define CONFIG_I2C_CMD_TREE 1 +#define CONFIG_SYS_MAX_I2C_BUS 2 +#define CONFIG_I2C_MUX 1 + +/* EEprom support */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 +#define CONFIG_SYS_I2C_MULTI_EEPROMS 1 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_ENABLE +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 + +/* Support the IVM EEprom */ +#define CONFIG_SYS_IVM_EEPROM_ADR 0x50 +#define CONFIG_SYS_IVM_EEPROM_MAX_LEN 0x400 +#define CONFIG_SYS_IVM_EEPROM_PAGE_LEN 0x100 + +/* I2C SYSMON (LM75, AD7414 is almost compatible) */ +#define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */ +#define CONFIG_DTT_SENSORS {0, 1, 2, 3} /* Sensor addresses */ +#define CONFIG_SYS_DTT_MAX_TEMP 70 +#define CONFIG_SYS_DTT_LOW_TEMP -30 +#define CONFIG_SYS_DTT_HYSTERESIS 3 +#define CONFIG_SYS_DTT_BUS_NUM (2) + #if defined(CONFIG_PCI) #define CONFIG_CMD_PCI #endif @@ -452,6 +485,8 @@ "loadfdt=tftp ${fdt_addr_r} ${fdt_file}\0" \ "loadkernel=tftp ${kernel_addr_r} ${boot_file}\0" \ "unlock=yes\0" \ + "EEprom_ivm=pca9547:70:9\0" \ + "dtt_bus=pca9547:70:a\0" \ "" #endif /* __CONFIG_H */ -- cgit From 118cbe3c35c898f8d020b29d6dc180307cacf147 Mon Sep 17 00:00:00 2001 From: Heiko Schocher Date: Tue, 24 Feb 2009 11:30:40 +0100 Subject: 83xx, kmeter1: autodetect size of DDR II RAM it is possible that some board variants have different DDR II RAM sizes. So we autodetect the size of the assembled RAM. Signed-off-by: Heiko Schocher Signed-off-by: Kim Phillips --- include/configs/kmeter1.h | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'include') diff --git a/include/configs/kmeter1.h b/include/configs/kmeter1.h index a23c9edb5f..ef3faa5ea7 100644 --- a/include/configs/kmeter1.h +++ b/include/configs/kmeter1.h @@ -92,8 +92,8 @@ * Manually set up DDR parameters */ #define CONFIG_DDR_II -#define CONFIG_SYS_DDR_SIZE 256 /* MB */ -#define CONFIG_SYS_DDR_CS0_BNDS 0x0000000f +#define CONFIG_SYS_DDR_SIZE 2048 /* MB */ +#define CONFIG_SYS_DDR_CS0_BNDS 0x0000007f #define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN | CSCONFIG_AP | \ CSCONFIG_ROW_BIT_13 | \ CSCONFIG_COL_BIT_10 | CSCONFIG_ODT_WR_ACS) -- cgit From 605f78e34a3f0103693b891f2573edd352e7d495 Mon Sep 17 00:00:00 2001 From: Heiko Schocher Date: Tue, 24 Feb 2009 11:30:44 +0100 Subject: 83xx, kmeter1: updates for 2009.03 - HRCW update HRCWH_BOOTSEQ_DISABLE not HRCWH_BOOTSEQ_NORMAL HRCWH_LALE_EARLY added - DDR-SDRAM settings modified. This solves sporadically problems with this memory. - CS1 now 128 MB window size - CS3 now 512 MB window size - PRAM activated - MTDPARTS_DEFAULT defined - CONFIG_HOSTNAME added - MONITOR_LEN now 384 KB Signed-off-by: Heiko Schocher Signed-off-by: Kim Phillips --- include/configs/kmeter1.h | 81 +++++++++++++++++++++++++++++------------------ 1 file changed, 50 insertions(+), 31 deletions(-) (limited to 'include') diff --git a/include/configs/kmeter1.h b/include/configs/kmeter1.h index ef3faa5ea7..49a801f63a 100644 --- a/include/configs/kmeter1.h +++ b/include/configs/kmeter1.h @@ -28,6 +28,7 @@ #define CONFIG_MPC83XX 1 /* MPC83XX family */ #define CONFIG_MPC8360 1 /* MPC8360 CPU specific */ #define CONFIG_KMETER1 1 /* KMETER1 board specific */ +#define CONFIG_HOSTNAME kmeter1 /* include common defines/options for all Keymile boards */ #include "keymile-common.h" @@ -52,10 +53,11 @@ #define CONFIG_SYS_HRCW_HIGH (\ HRCWH_CORE_ENABLE | \ HRCWH_FROM_0X00000100 | \ - HRCWH_BOOTSEQ_NORMAL | \ + HRCWH_BOOTSEQ_DISABLE | \ HRCWH_SW_WATCHDOG_DISABLE | \ HRCWH_ROM_LOC_LOCAL_16BIT | \ HRCWH_BIG_ENDIAN | \ + HRCWH_LALE_EARLY | \ HRCWH_LDP_CLEAR ) /* @@ -102,11 +104,12 @@ SDRAM_CFG_SREN) #define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 #define CONFIG_SYS_DDR_CLK_CNTL (DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05) -#define CONFIG_SYS_DDR_INTERVAL ((0x100 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \ - (0x406 << SDRAM_INTERVAL_REFINT_SHIFT)) +#define CONFIG_SYS_DDR_INTERVAL ((0x080 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \ + (0x3cf << SDRAM_INTERVAL_REFINT_SHIFT)) -#define CONFIG_SYS_DDR_MODE 0x04440242 -#define CONFIG_SYS_DDR_MODE2 0x00800000 +#define CONFIG_SYS_DDRCDR 0x40000001 +#define CONFIG_SYS_DDR_MODE 0x47860452 +#define CONFIG_SYS_DDR_MODE2 0x8080c000 #define CONFIG_SYS_DDR_TIMING_0 ((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \ (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \ @@ -117,22 +120,22 @@ (0 << TIMING_CFG0_WRT_SHIFT) | \ (0 << TIMING_CFG0_RWT_SHIFT)) -#define CONFIG_SYS_DDR_TIMING_1 (( TIMING_CFG1_CASLAT_40) | \ +#define CONFIG_SYS_DDR_TIMING_1 (( TIMING_CFG1_CASLAT_50) | \ ( 2 << TIMING_CFG1_WRTORD_SHIFT) | \ - ( 1 << TIMING_CFG1_ACTTOACT_SHIFT) | \ - ( 2 << TIMING_CFG1_WRREC_SHIFT) | \ - ( 2 << TIMING_CFG1_REFREC_SHIFT) | \ - ( 2 << TIMING_CFG1_ACTTORW_SHIFT) | \ - ( 6 << TIMING_CFG1_ACTTOPRE_SHIFT) | \ - ( 2 << TIMING_CFG1_PRETOACT_SHIFT)) - -#define CONFIG_SYS_DDR_TIMING_2 ((5 << TIMING_CFG2_FOUR_ACT_SHIFT) | \ + ( 2 << TIMING_CFG1_ACTTOACT_SHIFT) | \ + ( 3 << TIMING_CFG1_WRREC_SHIFT) | \ + ( 7 << TIMING_CFG1_REFREC_SHIFT) | \ + ( 3 << TIMING_CFG1_ACTTORW_SHIFT) | \ + ( 8 << TIMING_CFG1_ACTTOPRE_SHIFT) | \ + ( 3 << TIMING_CFG1_PRETOACT_SHIFT)) + +#define CONFIG_SYS_DDR_TIMING_2 ((8 << TIMING_CFG2_FOUR_ACT_SHIFT) | \ (3 << TIMING_CFG2_CKE_PLS_SHIFT) | \ (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \ - (1 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \ - (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \ + (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \ + (4 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \ (0 << TIMING_CFG2_ADD_LAT_SHIFT) | \ - (4 << TIMING_CFG2_CPO_SHIFT)) + (5 << TIMING_CFG2_CPO_SHIFT)) #define CONFIG_SYS_DDR_TIMING_3 0x00000000 @@ -142,9 +145,10 @@ #define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */ #define CONFIG_SYS_FLASH_BASE 0xF0000000 #define CONFIG_SYS_FLASH_BASE_1 0xF2000000 -#define CONFIG_SYS_PIGGY_BASE 0x80000000 +#define CONFIG_SYS_PIGGY_BASE 0xE8000000 +#define CONFIG_SYS_PIGGY_SIZE 128 #define CONFIG_SYS_PAXE_BASE 0xA0000000 -#define CONFIG_SYS_PAXE_SIZE 256 +#define CONFIG_SYS_PAXE_SIZE 512 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) #define CONFIG_SYS_RAMBOOT @@ -152,7 +156,7 @@ #undef CONFIG_SYS_RAMBOOT #endif -#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ +#define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 256 kB for Mon */ #define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ /* @@ -175,8 +179,8 @@ * Bank Bus Machine PortSz Size Device * ---- --- ------- ------ ----- ------ * 0 Local GPCM 16 bit 256MB FLASH - * 1 Local GPCM 8 bit 256KB GPIO/PIGGY - * 3 Local GPCM 8 bit 256MB PAXE + * 1 Local GPCM 8 bit 128MB GPIO/PIGGY + * 3 Local GPCM 8 bit 512MB PAXE * */ /* @@ -210,12 +214,12 @@ * PRIO1/PIGGY on the local bus CS1 */ #define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_PIGGY_BASE /* Window base at flash base */ -#define CONFIG_SYS_LBLAWAR1_PRELIM 0x80000011 /* 256KB window size */ +#define CONFIG_SYS_LBLAWAR1_PRELIM 0x8000001A /* 128MB window size */ #define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_PIGGY_BASE | \ (1 << BR_PS_SHIFT) | /* 8 bit port size */ \ BR_V) -#define CONFIG_SYS_OR1_PRELIM (0xfffc0000 | /* 256KB */ \ +#define CONFIG_SYS_OR1_PRELIM (MEG_TO_AM(CONFIG_SYS_PIGGY_SIZE) | /* 128MB */ \ OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 | \ OR_GPCM_SCY_2 | \ OR_GPCM_TRLX | OR_GPCM_EAD) @@ -224,7 +228,7 @@ * PAXE on the local bus CS3 */ #define CONFIG_SYS_LBLAWBAR3_PRELIM CONFIG_SYS_PAXE_BASE /* Window base at flash base */ -#define CONFIG_SYS_LBLAWAR3_PRELIM 0x8000001b /* 256MB window size */ +#define CONFIG_SYS_LBLAWAR3_PRELIM 0x8000001C /* 512MB window size */ #define CONFIG_SYS_BR3_PRELIM (CONFIG_SYS_PAXE_BASE | \ (1 << BR_PS_SHIFT) | /* 8 bit port size */ \ @@ -297,7 +301,7 @@ #else /* CFG_RAMBOOT */ #define CONFIG_SYS_NO_FLASH 1 /* Flash is not usable now */ #define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ -#define CONFIG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000) +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) #define CONFIG_ENV_SIZE 0x2000 #endif /* CFG_RAMBOOT */ @@ -378,7 +382,7 @@ /* PRIO1, PIGGY: icache cacheable, but dcache-inhibit and guarded */ #define CONFIG_SYS_IBAT2L (CONFIG_SYS_PIGGY_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) -#define CONFIG_SYS_IBAT2U (CONFIG_SYS_PIGGY_BASE | BATU_BL_256K | BATU_VS | BATU_VP) +#define CONFIG_SYS_IBAT2U (CONFIG_SYS_PIGGY_BASE | BATU_BL_128M | BATU_VS | BATU_VP) #define CONFIG_SYS_DBAT2L (CONFIG_SYS_PIGGY_BASE | BATL_PP_10 | \ BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) #define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U @@ -398,7 +402,7 @@ /* PAXE: icache cacheable, but dcache-inhibit and guarded */ #define CONFIG_SYS_IBAT5L (CONFIG_SYS_PAXE_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) -#define CONFIG_SYS_IBAT5U (CONFIG_SYS_PAXE_BASE | BATU_BL_256K | BATU_VS | BATU_VP) +#define CONFIG_SYS_IBAT5U (CONFIG_SYS_PAXE_BASE | BATU_BL_256M | BATU_VS | BATU_VP) #define CONFIG_SYS_DBAT5L (CONFIG_SYS_PAXE_BASE | BATL_PP_10 | \ BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) #define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U @@ -434,16 +438,25 @@ #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */ +#define BOOTFLASH_START F0000000 + +#define CONFIG_PRAM 512 /* protected RAM [KBytes] */ + +#define MTDIDS_DEFAULT "nor0=app" +#define MTDPARTS_DEFAULT \ + "mtdparts=app:256k(u-boot),128k(env),128k(envred)," \ + "1536k(esw0),8704k(rootfs0),1536k(esw1),2432k(rootfs1),640k(var),768k(cfg)" + /* * Environment Configuration */ #define CONFIG_ENV_OVERWRITE - -#if defined(CONFIG_UEC_ETH) -#define CONFIG_HAS_ETH0 +#ifndef CONFIG_KM_DEF_ENV /* if not set by keymile-common.h */ +#define CONFIG_KM_DEF_ENV "km-common=empty\0" #endif #define CONFIG_EXTRA_ENV_SETTINGS \ + CONFIG_KM_DEF_ENV \ "netdev=eth0\0" \ "rootpath=/opt/eldk/ppc_82xx\0" \ "nfsargs=setenv bootargs root=/dev/nfs rw " \ @@ -487,6 +500,12 @@ "unlock=yes\0" \ "EEprom_ivm=pca9547:70:9\0" \ "dtt_bus=pca9547:70:a\0" \ + "mtdids=nor0=app \0" \ + "mtdparts=" MK_STR(MTDPARTS_DEFAULT) "\0" \ "" +#if defined(CONFIG_UEC_ETH) +#define CONFIG_HAS_ETH0 +#endif + #endif /* __CONFIG_H */ -- cgit