From 84e106c09d324e345f335d2edef246d0b4c9131a Mon Sep 17 00:00:00 2001 From: Wolfgang Denk Date: Tue, 7 Feb 2006 15:18:25 +0100 Subject: Update default environment for INKA4x00 board. --- include/configs/inka4x0.h | 30 +++++++++++++++++++++++++----- 1 file changed, 25 insertions(+), 5 deletions(-) (limited to 'include') diff --git a/include/configs/inka4x0.h b/include/configs/inka4x0.h index c0cc4f1fbe..773d5d2c1d 100644 --- a/include/configs/inka4x0.h +++ b/include/configs/inka4x0.h @@ -101,7 +101,7 @@ /* * Autobooting */ -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ +#define CONFIG_BOOTDELAY 1 /* autoboot after 1 second */ #define CONFIG_PREBOOT "echo;" \ "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \ @@ -109,6 +109,16 @@ #undef CONFIG_BOOTARGS +#define CONFIG_ETHADDR 00:a0:a4:03:00:00 +#define CONFIG_OVERWRITE_ETHADDR_ONCE + +#define CONFIG_IPADDR 192.168.100.2 +#define CONFIG_SERVERIP 192.168.100.1 +#define CONFIG_NETMASK 255.255.255.0 +#define HOSTNAME inka4x0 +#define CONFIG_BOOTFILE /tftpboot/inka4x0/uImage +#define CONFIG_ROOTPATH /opt/eldk/ppc_6xx + #define CONFIG_EXTRA_ENV_SETTINGS \ "netdev=eth0\0" \ "nfsargs=setenv bootargs root=/dev/nfs rw " \ @@ -117,13 +127,22 @@ "addip=setenv bootargs ${bootargs} " \ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ ":${hostname}:${netdev}:off panic=1\0" \ - "flash_nfs=run nfsargs addip;" \ + "addcons=setenv bootargs ${bootargs} " \ + "console=ttyS0,${baudrate}\0" \ + "flash_nfs=run nfsargs addip addcons;" \ "bootm ${kernel_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \ - "rootpath=/opt/eldk/ppc_82xx\0" \ + "net_nfs=tftp 200000 ${bootfile};" \ + "run nfsargs addip addcons;bootm\0" \ + "enable_disp=mw.l 100000 04000000 1;" \ + "cp.l 100000 f0000b20 1;" \ + "cp.l 100000 f0000b28 1\0" \ + "ideargs=setenv bootargs root=/dev/hda1 rw\0" \ + "ide_boot=ext2load ide 0:1 200000 uImage;" \ + "run ideargs addip addcons enable_disp;bootm" \ + "brightness=255\0" \ "" -#define CONFIG_BOOTCOMMAND "run net_nfs" +#define CONFIG_BOOTCOMMAND "run ide_boot" /* * IPB Bus clocking configuration. @@ -193,6 +212,7 @@ */ /* #define CONFIG_FEC_10MBIT 1 */ #define CONFIG_PHY_ADDR 0x00 +#define CONFIG_MII /* * GPIO configuration -- cgit From 48a05a5188e03861da2378c95ba7963d810736aa Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Tue, 7 Feb 2006 16:51:04 +0100 Subject: Various changes to esd HH405 board specific files Patch by Matthias Fuchs, 07 Feb 2006 --- include/configs/HH405.h | 15 +++++++++++++-- 1 file changed, 13 insertions(+), 2 deletions(-) (limited to 'include') diff --git a/include/configs/HH405.h b/include/configs/HH405.h index 131c21555d..4f62b8ae8a 100644 --- a/include/configs/HH405.h +++ b/include/configs/HH405.h @@ -5,6 +5,9 @@ * (C) Copyright 2005 * Stefan Roese, DENX Software Engineering, sr@denx.de. * + * (C) Copyright 2006 + * Matthias Fuchs, esd GmbH, matthias.fuchs@esd-electronics.com + * * See file CREDITS for list of people who contributed to this * project. * @@ -61,9 +64,13 @@ #define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ +#define CONFIG_NET_MULTI 1 +#undef CONFIG_HAS_ETH1 + #define CONFIG_MII 1 /* MII PHY management */ -#define CONFIG_PHY_ADDR 0 /* PHY address */ +#define CONFIG_PHY_ADDR 0 /* PHY address */ #define CONFIG_LXT971_NO_SLEEP 1 /* disable sleep mode in LXT971 */ +#define CONFIG_RESET_PHY_R 1 /* use reset_phy() to disable phy sleep mode */ #define CONFIG_PHY_CLK_FREQ EMAC_STACR_CLK_66MHZ /* 66 MHz OPB clock*/ @@ -79,6 +86,7 @@ #else #define CONFIG_VIDEO_SM501_16BPP #endif +#define CONFIG_VIDEO_SM501_FBMEM_OFFSET 0x10000 #define CONFIG_CFB_CONSOLE #define CONFIG_VIDEO_LOGO #define CONFIG_VGA_AS_SINGLE_DEVICE @@ -434,9 +442,12 @@ #define CFG_FPGA_CTRL_VGA0_BL_MODE 0x0008 #define CFG_FPGA_CTRL_CF_RESET 0x0040 #define CFG_FPGA_CTRL_PS2_PWR 0x0080 -#define CFG_FPGA_CTRL_CF_PWR 0x0100 /* low active */ +#define CFG_FPGA_CTRL_CF_PWRN 0x0100 /* low active */ #define CFG_FPGA_CTRL_CF_BUS_EN 0x0200 #define CFG_FPGA_CTRL_LCD_CLK 0x7000 /* Mask for lcd clock */ +#define CFG_FPGA_CTRL_OW_ENABLE 0x8000 + +#define CFG_FPGA_STATUS_CF_DETECT 0x8000 #define LCD_CLK_OFF 0x0000 /* Off */ #define LCD_CLK_02083 0x1000 /* 2.083 MHz */ -- cgit From 79830d591afb758be8556396949d433fee1527c2 Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Wed, 8 Feb 2006 15:54:15 +0100 Subject: Convert CPCI750 to use common CFI flash driver Patch by Reinhard Arlt, 8 Feb 2006 --- include/configs/CPCI750.h | 12 +++++++++--- 1 file changed, 9 insertions(+), 3 deletions(-) (limited to 'include') diff --git a/include/configs/CPCI750.h b/include/configs/CPCI750.h index 150e5267f2..1632f374c3 100644 --- a/include/configs/CPCI750.h +++ b/include/configs/CPCI750.h @@ -285,13 +285,19 @@ * FLASH related *----------------------------------------------------------------------*/ +#define CFG_FLASH_CFI_DRIVER #define CFG_FLASH_CFI 1 /* Flash is CFI conformant */ -#define CFG_MAX_FLASH_SECT 128 /* max number of sectors on one chip */ -#define CFG_MAX_FLASH_BANKS 4 /* max number of memory banks */ -#define CFG_FLASH_INCREMENT 0x01000000 /* there is only one bank */ #define CFG_FLASH_PROTECTION 1 /* use hardware protection */ #define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ #define CFG_FLASH_BASE 0xfc000000 /* start of flash banks */ +#define CFG_MAX_FLASH_BANKS 4 /* max number of memory banks */ +#define CFG_FLASH_INCREMENT 0x01000000 /* size of flash bank */ +#define CFG_MAX_FLASH_SECT 128 /* max number of sectors on one chip */ +#define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE, \ + CFG_FLASH_BASE + 1*CFG_FLASH_INCREMENT, \ + CFG_FLASH_BASE + 2*CFG_FLASH_INCREMENT, \ + CFG_FLASH_BASE + 3*CFG_FLASH_INCREMENT } +#define CFG_FLASH_EMPTY_INFO 1 /* show if bank is empty */ /* areas to map different things with the GT in physical space */ #define CFG_DRAM_BANKS 4 -- cgit From 075866d840e16c9848f4b2ff1b02ec855c112903 Mon Sep 17 00:00:00 2001 From: Heiko Schocher Date: Mon, 20 Feb 2006 17:34:12 +0100 Subject: [Patch] Add basic support for the SMMACO4 Board from PanDaCom. Signed-off-by: Heiko Schocher --- include/configs/SMMACO4.h | 374 ++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 374 insertions(+) create mode 100644 include/configs/SMMACO4.h (limited to 'include') diff --git a/include/configs/SMMACO4.h b/include/configs/SMMACO4.h new file mode 100644 index 0000000000..157c6ef4a9 --- /dev/null +++ b/include/configs/SMMACO4.h @@ -0,0 +1,374 @@ +/* + * (C) Copyright 2003-2006 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * (C) Copyright 2004-2005 + * Martin Krause, TQ-Systems GmbH, martin.krause@tqs.de + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_MPC5xxx 1 /* This is an MPC5xxx CPU */ +#define CONFIG_MPC5200 1 /* (more precisely an MPC5200 CPU) */ +#define CONFIG_TQM5200 1 /* ... on TQM5200 module */ +#undef CONFIG_TQM5200_REV100 /* define for revision 100 modules */ + +#define CFG_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */ + +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#define CFG_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +#endif + +/* + * Serial console configuration + */ +#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */ +#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */ +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } + +/* Partitions */ +#define CONFIG_MAC_PARTITION +#define CONFIG_DOS_PARTITION +#define CONFIG_ISO_PARTITION + +/* POST support */ +#define CONFIG_POST (CFG_POST_MEMORY | \ + CFG_POST_CPU | \ + CFG_POST_I2C) + +#ifdef CONFIG_POST +#define CFG_CMD_POST_DIAG CFG_CMD_DIAG +/* preserve space for the post_word at end of on-chip SRAM */ +#define MPC5XXX_SRAM_POST_SIZE MPC5XXX_SRAM_SIZE-4 +#else +#define CFG_CMD_POST_DIAG 0 +#endif + +/* + * Supported commands + */ +#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \ + CFG_CMD_ASKENV | \ + CFG_CMD_DATE | \ + CFG_CMD_DHCP | \ + CFG_CMD_ECHO | \ + CFG_CMD_EEPROM | \ + CFG_CMD_I2C | \ + CFG_CMD_JFFS2 | \ + CFG_CMD_MII | \ + CFG_CMD_NFS | \ + CFG_CMD_PING | \ + CFG_CMD_POST_DIAG | \ + CFG_CMD_REGINFO | \ + CFG_CMD_SNTP | \ + CFG_CMD_BSP) + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include + +#define CONFIG_TIMESTAMP /* display image timestamps */ + +#if (TEXT_BASE == 0xFC000000) /* Boot low */ +# define CFG_LOWBOOT 1 +#endif + +/* + * Autobooting + */ +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ + +#define CONFIG_PREBOOT "echo;" \ + "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \ + "echo" + +#undef CONFIG_BOOTARGS + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "rootpath=/opt/eldk/ppc_6xx\0" \ + "ramargs=setenv bootargs root=/dev/ram rw\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw " \ + "nfsroot=${serverip}:${rootpath}\0" \ + "addip=setenv bootargs ${bootargs} " \ + "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ + ":${hostname}:${netdev}:off panic=1\0" \ + "flash_self=run ramargs addip;" \ + "bootm ${kernel_addr} ${ramdisk_addr}\0" \ + "flash_nfs=run nfsargs addip;" \ + "bootm ${kernel_addr}\0" \ + "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \ + "bootfile=/tftpboot/smmaco4/uImage\0" \ + "load=tftp 200000 ${u-boot}\0" \ + "u-boot=/tftpboot/smmaco4/u-boot.bin\0" \ + "update=protect off FC000000 FC05FFFF;" \ + "erase FC000000 FC05FFFF;" \ + "cp.b 200000 FC000000 ${filesize};" \ + "protect on FC000000 FC05FFFF\0" \ + "" + +#define CONFIG_BOOTCOMMAND "run net_nfs" + +/* + * IPB Bus clocking configuration. + */ +#define CFG_IPBSPEED_133 /* define for 133MHz speed */ + +#if defined(CFG_IPBSPEED_133) +/* + * PCI Bus clocking configuration + * + * Actually a PCI Clock of 66 MHz is only set (in cpu_init.c) if + * CFG_IPBSPEED_133 is defined. This is because a PCI Clock of 66 MHz yet hasn't + * been tested with a IPB Bus Clock of 66 MHz. + */ +#define CFG_PCISPEED_66 /* define for 66MHz speed */ +#endif + +/* + * I2C configuration + */ +#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ +#ifdef CONFIG_TQM5200_REV100 +#define CFG_I2C_MODULE 1 /* Select I2C module #1 for rev. 100 board */ +#else +#define CFG_I2C_MODULE 2 /* Select I2C module #2 for all other revs */ +#endif + +/* + * I2C clock frequency + * + * Please notice, that the resulting clock frequency could differ from the + * configured value. This is because the I2C clock is derived from system + * clock over a frequency divider with only a few divider values. U-boot + * calculates the best approximation for CFG_I2C_SPEED. However the calculated + * approximation allways lies below the configured value, never above. + */ +#define CFG_I2C_SPEED 100000 /* 100 kHz */ +#define CFG_I2C_SLAVE 0x7F + +/* + * EEPROM configuration for onboard EEPROM M24C32 (M24C64 should work + * also). For other EEPROMs configuration should be verified. On Mini-FAP the + * EEPROM (24C64) is on the same I2C address (but on other I2C bus), so the + * same configuration could be used. + */ +#define CFG_I2C_EEPROM_ADDR 0x50 /* 1010000x */ +#define CFG_I2C_EEPROM_ADDR_LEN 2 +#define CFG_EEPROM_PAGE_WRITE_BITS 5 /* =32 Bytes per write */ +#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 20 + +/* + * Flash configuration + */ +#define CFG_FLASH_BASE TEXT_BASE /* 0xFC000000 */ + +/* use CFI flash driver if no module variant is spezified */ +#define CFG_FLASH_CFI 1 /* Flash is CFI conformant */ +#define CFG_FLASH_CFI_DRIVER 1 /* Use the common driver */ +#define CFG_FLASH_BANKS_LIST { CFG_BOOTCS_START } +#define CFG_FLASH_EMPTY_INFO +#define CFG_FLASH_SIZE 0x04000000 /* 64 MByte */ +#define CFG_MAX_FLASH_SECT 512 /* max num of sects on one chip */ +#undef CFG_FLASH_USE_BUFFER_WRITE /* not supported yet for AMD */ + +#if !defined(CFG_LOWBOOT) +#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x00760000 + 0x00800000) +#else /* CFG_LOWBOOT */ +#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x00060000) +#endif /* CFG_LOWBOOT */ +#define CFG_MAX_FLASH_BANKS 1 /* max num of flash banks + (= chip selects) */ +#define CFG_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */ + +/* Dynamic MTD partition support */ +#define CONFIG_JFFS2_CMDLINE +#define MTDIDS_DEFAULT "nor0=TQM5200-0" +#define MTDPARTS_DEFAULT "mtdparts=TQM5200-0:640k(firmware)," \ + "1408k(kernel)," \ + "2m(initrd)," \ + "4m(small-fs)," \ + "16m(big-fs)," \ + "8m(misc)" + +/* + * Environment settings + */ +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_SIZE 0x10000 +#define CFG_ENV_SECT_SIZE 0x20000 +#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR + CFG_ENV_SECT_SIZE) +#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) + +/* + * Memory map + */ +#define CFG_MBAR 0xF0000000 +#define CFG_SDRAM_BASE 0x00000000 +#define CFG_DEFAULT_MBAR 0x80000000 + +/* Use ON-Chip SRAM until RAM will be available */ +#define CFG_INIT_RAM_ADDR MPC5XXX_SRAM +#ifdef CONFIG_POST +/* preserve space for the post_word at end of on-chip SRAM */ +#define CFG_INIT_RAM_END MPC5XXX_SRAM_POST_SIZE +#else +#define CFG_INIT_RAM_END MPC5XXX_SRAM_SIZE +#endif + + +#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +#define CFG_MONITOR_BASE TEXT_BASE +#if (CFG_MONITOR_BASE < CFG_FLASH_BASE) +# define CFG_RAMBOOT 1 +#endif + +#define CFG_MONITOR_LEN (384 << 10) /* Reserve 384 kB for Monitor */ +#define CFG_MALLOC_LEN (256 << 10) /* Reserve 256 kB for malloc() */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/* + * Ethernet configuration + */ +#define CONFIG_MPC5xxx_FEC 1 +/* + * Define CONFIG_FEC_10MBIT to force FEC at 10Mb + */ +/* #define CONFIG_FEC_10MBIT 1 */ +#define CONFIG_PHY_ADDR 0x00 + +/* + * GPIO configuration + * + * use pin gpio_wkup_6 as second SDRAM chip select (mem_cs1): + * Bit 0 (mask: 0x80000000): 1 + * use ALT CAN position: Bits 2-3 (mask: 0x30000000): + * 00 -> No Alternatives, CAN1/2 on PSC2 according to PSC2 setting. + * 01 -> CAN1 on I2C1, CAN2 on Tmr0/1. + * Use for REV200 STK52XX boards. Do not use with REV100 modules + * (because, there I2C1 is used as I2C bus) + * use PSC1 as UART: Bits 28-31 (mask: 0x00000007): 0100 + * use PSC2 as CAN: Bits 25:27 (mask: 0x00000030) + * 000 -> All PSC2 pins are GIOPs + * 001 -> CAN1/2 on PSC2 pins + * Use for REV100 STK52xx boards + * use PSC6: + * on STK52xx: + * use as UART. Pins PSC6_0 to PSC6_3 are used. + * Bits 9:11 (mask: 0x00700000): + * 101 -> PSC6 : Extended POST test is not available + * on MINI-FAP and TQM5200_IB: + * use PSC6_0 to PSC6_3 as GPIO: Bits 9:11 (mask: 0x00700000): + * 000 -> PSC6 could not be used as UART, CODEC or IrDA + * GPIO on PSC6_3 is used in post_hotkeys_pressed() to enable extended POST + * tests. + */ +#if defined (CONFIG_MINIFAP) +# define CFG_GPS_PORT_CONFIG 0x91000004 +#elif defined (CONFIG_STK52XX) +# if defined (CONFIG_STK52XX_REV100) +# define CFG_GPS_PORT_CONFIG 0x81500014 +# else /* STK52xx REV200 and above */ +# if defined (CONFIG_TQM5200_REV100) +# error TQM5200 REV100 not supported on STK52XX REV200 or above +# else/* TQM5200 REV200 and above */ +# define CFG_GPS_PORT_CONFIG 0x91500004 +# endif +# endif +#else /* TMQ5200 Inbetriebnahme-Board */ +# define CFG_GPS_PORT_CONFIG 0x81000004 +#endif + +/* + * RTC configuration + */ +#define CONFIG_RTC_MPC5200 1 /* use internal MPC5200 RTC */ + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +/* Enable an alternate, more extensive memory test */ +#define CFG_ALT_MEMTEST + +#define CFG_MEMTEST_START 0x00100000 /* memtest works on */ +#define CFG_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */ + +#define CFG_LOAD_ADDR 0x100000 /* default load address */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +/* + * Enable loopw commando. This has only affect, if CFG_CMD_MEM is defined, + * which is normally part of the default commands (CFV_CMD_DFL) + */ +#define CONFIG_LOOPW + +/* + * Various low-level settings + */ +#if defined(CONFIG_MPC5200) +#define CFG_HID0_INIT HID0_ICE | HID0_ICFI +#define CFG_HID0_FINAL HID0_ICE +#else +#define CFG_HID0_INIT 0 +#define CFG_HID0_FINAL 0 +#endif + +#define CFG_BOOTCS_START CFG_FLASH_BASE +#define CFG_BOOTCS_SIZE CFG_FLASH_SIZE +#ifdef CFG_PCISPEED_66 +#define CFG_BOOTCS_CFG 0x0008DF30 /* for pci_clk = 66 MHz */ +#else +#define CFG_BOOTCS_CFG 0x0004DF30 /* for pci_clk = 33 MHz */ +#endif +#define CFG_CS0_START CFG_FLASH_BASE +#define CFG_CS0_SIZE CFG_FLASH_SIZE + +#define CFG_CS_BURST 0x00000000 +#define CFG_CS_DEADCYCLE 0x33333311 /* 1 dead cycle for flash and SM501 */ + +#define CFG_RESET_ADDRESS 0xff000000 + +#endif /* __CONFIG_H */ -- cgit From 881a87ecbab328656eb3e9d25c3ed6868587b197 Mon Sep 17 00:00:00 2001 From: Wolfgang Denk Date: Tue, 21 Feb 2006 17:33:04 +0100 Subject: Add GIT version information (commid ID) to untagged U-Boot versions As done in the linux kernel, the U-Boot version (U_BOOT_VERSION) of all unreleased (untagged) U-Boot images will be automatically extended upon compiletime with a part of the GIT commit ID and possibly with "dirty" if uncommited changes are detected. Here an example for the resulting version: "U-Boot 1.1.4-g3457ac18-dirty" The version is now maintained in the toplevel Makefile and the version headers are autogenerated. Patch by Stefan Roese, 9 Feb 2006 --- include/version.h | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'include') diff --git a/include/version.h b/include/version.h index 4f8b498cf3..b56d2e9900 100644 --- a/include/version.h +++ b/include/version.h @@ -1,5 +1,5 @@ /* - * (C) Copyright 2000-2003 + * (C) Copyright 2000-2006 * Wolfgang Denk, DENX Software Engineering, wd@denx.de. * * See file CREDITS for list of people who contributed to this @@ -24,6 +24,6 @@ #ifndef __VERSION_H__ #define __VERSION_H__ -#define U_BOOT_VERSION "U-Boot 1.1.4" +#include "version_autogenerated.h" #endif /* __VERSION_H__ */ -- cgit From 5f0be01356aa7dafc2e5e4ee07715d05bbe9013b Mon Sep 17 00:00:00 2001 From: Wolfgang Denk Date: Wed, 22 Feb 2006 02:39:31 +0100 Subject: Disable CMD_BSP for SMMACO4 board. --- include/configs/SMMACO4.h | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-) (limited to 'include') diff --git a/include/configs/SMMACO4.h b/include/configs/SMMACO4.h index 157c6ef4a9..e106b3b574 100644 --- a/include/configs/SMMACO4.h +++ b/include/configs/SMMACO4.h @@ -88,8 +88,7 @@ CFG_CMD_PING | \ CFG_CMD_POST_DIAG | \ CFG_CMD_REGINFO | \ - CFG_CMD_SNTP | \ - CFG_CMD_BSP) + CFG_CMD_SNTP ) /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ #include -- cgit From 6624b687bc2b747233090e67628df37d1c84ed17 Mon Sep 17 00:00:00 2001 From: Wolfgang Denk Date: Wed, 22 Feb 2006 10:25:39 +0100 Subject: Rename SMMACO4 board into smmaco4 for consistency with Linux. --- include/configs/SMMACO4.h | 373 ---------------------------------------------- include/configs/smmaco4.h | 373 ++++++++++++++++++++++++++++++++++++++++++++++ 2 files changed, 373 insertions(+), 373 deletions(-) delete mode 100644 include/configs/SMMACO4.h create mode 100644 include/configs/smmaco4.h (limited to 'include') diff --git a/include/configs/SMMACO4.h b/include/configs/SMMACO4.h deleted file mode 100644 index e106b3b574..0000000000 --- a/include/configs/SMMACO4.h +++ /dev/null @@ -1,373 +0,0 @@ -/* - * (C) Copyright 2003-2006 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * (C) Copyright 2004-2005 - * Martin Krause, TQ-Systems GmbH, martin.krause@tqs.de - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - * (easy to change) - */ - -#define CONFIG_MPC5xxx 1 /* This is an MPC5xxx CPU */ -#define CONFIG_MPC5200 1 /* (more precisely an MPC5200 CPU) */ -#define CONFIG_TQM5200 1 /* ... on TQM5200 module */ -#undef CONFIG_TQM5200_REV100 /* define for revision 100 modules */ - -#define CFG_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */ - -#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ -#define BOOTFLAG_WARM 0x02 /* Software reboot */ - -#define CFG_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) -# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - -/* - * Serial console configuration - */ -#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */ -#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */ -#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } - -/* Partitions */ -#define CONFIG_MAC_PARTITION -#define CONFIG_DOS_PARTITION -#define CONFIG_ISO_PARTITION - -/* POST support */ -#define CONFIG_POST (CFG_POST_MEMORY | \ - CFG_POST_CPU | \ - CFG_POST_I2C) - -#ifdef CONFIG_POST -#define CFG_CMD_POST_DIAG CFG_CMD_DIAG -/* preserve space for the post_word at end of on-chip SRAM */ -#define MPC5XXX_SRAM_POST_SIZE MPC5XXX_SRAM_SIZE-4 -#else -#define CFG_CMD_POST_DIAG 0 -#endif - -/* - * Supported commands - */ -#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \ - CFG_CMD_ASKENV | \ - CFG_CMD_DATE | \ - CFG_CMD_DHCP | \ - CFG_CMD_ECHO | \ - CFG_CMD_EEPROM | \ - CFG_CMD_I2C | \ - CFG_CMD_JFFS2 | \ - CFG_CMD_MII | \ - CFG_CMD_NFS | \ - CFG_CMD_PING | \ - CFG_CMD_POST_DIAG | \ - CFG_CMD_REGINFO | \ - CFG_CMD_SNTP ) - -/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ -#include - -#define CONFIG_TIMESTAMP /* display image timestamps */ - -#if (TEXT_BASE == 0xFC000000) /* Boot low */ -# define CFG_LOWBOOT 1 -#endif - -/* - * Autobooting - */ -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ - -#define CONFIG_PREBOOT "echo;" \ - "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "rootpath=/opt/eldk/ppc_6xx\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "flash_self=run ramargs addip;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "flash_nfs=run nfsargs addip;" \ - "bootm ${kernel_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \ - "bootfile=/tftpboot/smmaco4/uImage\0" \ - "load=tftp 200000 ${u-boot}\0" \ - "u-boot=/tftpboot/smmaco4/u-boot.bin\0" \ - "update=protect off FC000000 FC05FFFF;" \ - "erase FC000000 FC05FFFF;" \ - "cp.b 200000 FC000000 ${filesize};" \ - "protect on FC000000 FC05FFFF\0" \ - "" - -#define CONFIG_BOOTCOMMAND "run net_nfs" - -/* - * IPB Bus clocking configuration. - */ -#define CFG_IPBSPEED_133 /* define for 133MHz speed */ - -#if defined(CFG_IPBSPEED_133) -/* - * PCI Bus clocking configuration - * - * Actually a PCI Clock of 66 MHz is only set (in cpu_init.c) if - * CFG_IPBSPEED_133 is defined. This is because a PCI Clock of 66 MHz yet hasn't - * been tested with a IPB Bus Clock of 66 MHz. - */ -#define CFG_PCISPEED_66 /* define for 66MHz speed */ -#endif - -/* - * I2C configuration - */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#ifdef CONFIG_TQM5200_REV100 -#define CFG_I2C_MODULE 1 /* Select I2C module #1 for rev. 100 board */ -#else -#define CFG_I2C_MODULE 2 /* Select I2C module #2 for all other revs */ -#endif - -/* - * I2C clock frequency - * - * Please notice, that the resulting clock frequency could differ from the - * configured value. This is because the I2C clock is derived from system - * clock over a frequency divider with only a few divider values. U-boot - * calculates the best approximation for CFG_I2C_SPEED. However the calculated - * approximation allways lies below the configured value, never above. - */ -#define CFG_I2C_SPEED 100000 /* 100 kHz */ -#define CFG_I2C_SLAVE 0x7F - -/* - * EEPROM configuration for onboard EEPROM M24C32 (M24C64 should work - * also). For other EEPROMs configuration should be verified. On Mini-FAP the - * EEPROM (24C64) is on the same I2C address (but on other I2C bus), so the - * same configuration could be used. - */ -#define CFG_I2C_EEPROM_ADDR 0x50 /* 1010000x */ -#define CFG_I2C_EEPROM_ADDR_LEN 2 -#define CFG_EEPROM_PAGE_WRITE_BITS 5 /* =32 Bytes per write */ -#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 20 - -/* - * Flash configuration - */ -#define CFG_FLASH_BASE TEXT_BASE /* 0xFC000000 */ - -/* use CFI flash driver if no module variant is spezified */ -#define CFG_FLASH_CFI 1 /* Flash is CFI conformant */ -#define CFG_FLASH_CFI_DRIVER 1 /* Use the common driver */ -#define CFG_FLASH_BANKS_LIST { CFG_BOOTCS_START } -#define CFG_FLASH_EMPTY_INFO -#define CFG_FLASH_SIZE 0x04000000 /* 64 MByte */ -#define CFG_MAX_FLASH_SECT 512 /* max num of sects on one chip */ -#undef CFG_FLASH_USE_BUFFER_WRITE /* not supported yet for AMD */ - -#if !defined(CFG_LOWBOOT) -#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x00760000 + 0x00800000) -#else /* CFG_LOWBOOT */ -#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x00060000) -#endif /* CFG_LOWBOOT */ -#define CFG_MAX_FLASH_BANKS 1 /* max num of flash banks - (= chip selects) */ -#define CFG_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */ -#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */ - -/* Dynamic MTD partition support */ -#define CONFIG_JFFS2_CMDLINE -#define MTDIDS_DEFAULT "nor0=TQM5200-0" -#define MTDPARTS_DEFAULT "mtdparts=TQM5200-0:640k(firmware)," \ - "1408k(kernel)," \ - "2m(initrd)," \ - "4m(small-fs)," \ - "16m(big-fs)," \ - "8m(misc)" - -/* - * Environment settings - */ -#define CFG_ENV_IS_IN_FLASH 1 -#define CFG_ENV_SIZE 0x10000 -#define CFG_ENV_SECT_SIZE 0x20000 -#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR + CFG_ENV_SECT_SIZE) -#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) - -/* - * Memory map - */ -#define CFG_MBAR 0xF0000000 -#define CFG_SDRAM_BASE 0x00000000 -#define CFG_DEFAULT_MBAR 0x80000000 - -/* Use ON-Chip SRAM until RAM will be available */ -#define CFG_INIT_RAM_ADDR MPC5XXX_SRAM -#ifdef CONFIG_POST -/* preserve space for the post_word at end of on-chip SRAM */ -#define CFG_INIT_RAM_END MPC5XXX_SRAM_POST_SIZE -#else -#define CFG_INIT_RAM_END MPC5XXX_SRAM_SIZE -#endif - - -#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ -#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) -#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET - -#define CFG_MONITOR_BASE TEXT_BASE -#if (CFG_MONITOR_BASE < CFG_FLASH_BASE) -# define CFG_RAMBOOT 1 -#endif - -#define CFG_MONITOR_LEN (384 << 10) /* Reserve 384 kB for Monitor */ -#define CFG_MALLOC_LEN (256 << 10) /* Reserve 256 kB for malloc() */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/* - * Ethernet configuration - */ -#define CONFIG_MPC5xxx_FEC 1 -/* - * Define CONFIG_FEC_10MBIT to force FEC at 10Mb - */ -/* #define CONFIG_FEC_10MBIT 1 */ -#define CONFIG_PHY_ADDR 0x00 - -/* - * GPIO configuration - * - * use pin gpio_wkup_6 as second SDRAM chip select (mem_cs1): - * Bit 0 (mask: 0x80000000): 1 - * use ALT CAN position: Bits 2-3 (mask: 0x30000000): - * 00 -> No Alternatives, CAN1/2 on PSC2 according to PSC2 setting. - * 01 -> CAN1 on I2C1, CAN2 on Tmr0/1. - * Use for REV200 STK52XX boards. Do not use with REV100 modules - * (because, there I2C1 is used as I2C bus) - * use PSC1 as UART: Bits 28-31 (mask: 0x00000007): 0100 - * use PSC2 as CAN: Bits 25:27 (mask: 0x00000030) - * 000 -> All PSC2 pins are GIOPs - * 001 -> CAN1/2 on PSC2 pins - * Use for REV100 STK52xx boards - * use PSC6: - * on STK52xx: - * use as UART. Pins PSC6_0 to PSC6_3 are used. - * Bits 9:11 (mask: 0x00700000): - * 101 -> PSC6 : Extended POST test is not available - * on MINI-FAP and TQM5200_IB: - * use PSC6_0 to PSC6_3 as GPIO: Bits 9:11 (mask: 0x00700000): - * 000 -> PSC6 could not be used as UART, CODEC or IrDA - * GPIO on PSC6_3 is used in post_hotkeys_pressed() to enable extended POST - * tests. - */ -#if defined (CONFIG_MINIFAP) -# define CFG_GPS_PORT_CONFIG 0x91000004 -#elif defined (CONFIG_STK52XX) -# if defined (CONFIG_STK52XX_REV100) -# define CFG_GPS_PORT_CONFIG 0x81500014 -# else /* STK52xx REV200 and above */ -# if defined (CONFIG_TQM5200_REV100) -# error TQM5200 REV100 not supported on STK52XX REV200 or above -# else/* TQM5200 REV200 and above */ -# define CFG_GPS_PORT_CONFIG 0x91500004 -# endif -# endif -#else /* TMQ5200 Inbetriebnahme-Board */ -# define CFG_GPS_PORT_CONFIG 0x81000004 -#endif - -/* - * RTC configuration - */ -#define CONFIG_RTC_MPC5200 1 /* use internal MPC5200 RTC */ - -/* - * Miscellaneous configurable options - */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ - -/* Enable an alternate, more extensive memory test */ -#define CFG_ALT_MEMTEST - -#define CFG_MEMTEST_START 0x00100000 /* memtest works on */ -#define CFG_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */ - -#define CFG_LOAD_ADDR 0x100000 /* default load address */ - -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ - -/* - * Enable loopw commando. This has only affect, if CFG_CMD_MEM is defined, - * which is normally part of the default commands (CFV_CMD_DFL) - */ -#define CONFIG_LOOPW - -/* - * Various low-level settings - */ -#if defined(CONFIG_MPC5200) -#define CFG_HID0_INIT HID0_ICE | HID0_ICFI -#define CFG_HID0_FINAL HID0_ICE -#else -#define CFG_HID0_INIT 0 -#define CFG_HID0_FINAL 0 -#endif - -#define CFG_BOOTCS_START CFG_FLASH_BASE -#define CFG_BOOTCS_SIZE CFG_FLASH_SIZE -#ifdef CFG_PCISPEED_66 -#define CFG_BOOTCS_CFG 0x0008DF30 /* for pci_clk = 66 MHz */ -#else -#define CFG_BOOTCS_CFG 0x0004DF30 /* for pci_clk = 33 MHz */ -#endif -#define CFG_CS0_START CFG_FLASH_BASE -#define CFG_CS0_SIZE CFG_FLASH_SIZE - -#define CFG_CS_BURST 0x00000000 -#define CFG_CS_DEADCYCLE 0x33333311 /* 1 dead cycle for flash and SM501 */ - -#define CFG_RESET_ADDRESS 0xff000000 - -#endif /* __CONFIG_H */ diff --git a/include/configs/smmaco4.h b/include/configs/smmaco4.h new file mode 100644 index 0000000000..e106b3b574 --- /dev/null +++ b/include/configs/smmaco4.h @@ -0,0 +1,373 @@ +/* + * (C) Copyright 2003-2006 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * (C) Copyright 2004-2005 + * Martin Krause, TQ-Systems GmbH, martin.krause@tqs.de + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_MPC5xxx 1 /* This is an MPC5xxx CPU */ +#define CONFIG_MPC5200 1 /* (more precisely an MPC5200 CPU) */ +#define CONFIG_TQM5200 1 /* ... on TQM5200 module */ +#undef CONFIG_TQM5200_REV100 /* define for revision 100 modules */ + +#define CFG_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */ + +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#define CFG_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +#endif + +/* + * Serial console configuration + */ +#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */ +#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */ +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } + +/* Partitions */ +#define CONFIG_MAC_PARTITION +#define CONFIG_DOS_PARTITION +#define CONFIG_ISO_PARTITION + +/* POST support */ +#define CONFIG_POST (CFG_POST_MEMORY | \ + CFG_POST_CPU | \ + CFG_POST_I2C) + +#ifdef CONFIG_POST +#define CFG_CMD_POST_DIAG CFG_CMD_DIAG +/* preserve space for the post_word at end of on-chip SRAM */ +#define MPC5XXX_SRAM_POST_SIZE MPC5XXX_SRAM_SIZE-4 +#else +#define CFG_CMD_POST_DIAG 0 +#endif + +/* + * Supported commands + */ +#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \ + CFG_CMD_ASKENV | \ + CFG_CMD_DATE | \ + CFG_CMD_DHCP | \ + CFG_CMD_ECHO | \ + CFG_CMD_EEPROM | \ + CFG_CMD_I2C | \ + CFG_CMD_JFFS2 | \ + CFG_CMD_MII | \ + CFG_CMD_NFS | \ + CFG_CMD_PING | \ + CFG_CMD_POST_DIAG | \ + CFG_CMD_REGINFO | \ + CFG_CMD_SNTP ) + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include + +#define CONFIG_TIMESTAMP /* display image timestamps */ + +#if (TEXT_BASE == 0xFC000000) /* Boot low */ +# define CFG_LOWBOOT 1 +#endif + +/* + * Autobooting + */ +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ + +#define CONFIG_PREBOOT "echo;" \ + "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \ + "echo" + +#undef CONFIG_BOOTARGS + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "rootpath=/opt/eldk/ppc_6xx\0" \ + "ramargs=setenv bootargs root=/dev/ram rw\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw " \ + "nfsroot=${serverip}:${rootpath}\0" \ + "addip=setenv bootargs ${bootargs} " \ + "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ + ":${hostname}:${netdev}:off panic=1\0" \ + "flash_self=run ramargs addip;" \ + "bootm ${kernel_addr} ${ramdisk_addr}\0" \ + "flash_nfs=run nfsargs addip;" \ + "bootm ${kernel_addr}\0" \ + "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \ + "bootfile=/tftpboot/smmaco4/uImage\0" \ + "load=tftp 200000 ${u-boot}\0" \ + "u-boot=/tftpboot/smmaco4/u-boot.bin\0" \ + "update=protect off FC000000 FC05FFFF;" \ + "erase FC000000 FC05FFFF;" \ + "cp.b 200000 FC000000 ${filesize};" \ + "protect on FC000000 FC05FFFF\0" \ + "" + +#define CONFIG_BOOTCOMMAND "run net_nfs" + +/* + * IPB Bus clocking configuration. + */ +#define CFG_IPBSPEED_133 /* define for 133MHz speed */ + +#if defined(CFG_IPBSPEED_133) +/* + * PCI Bus clocking configuration + * + * Actually a PCI Clock of 66 MHz is only set (in cpu_init.c) if + * CFG_IPBSPEED_133 is defined. This is because a PCI Clock of 66 MHz yet hasn't + * been tested with a IPB Bus Clock of 66 MHz. + */ +#define CFG_PCISPEED_66 /* define for 66MHz speed */ +#endif + +/* + * I2C configuration + */ +#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ +#ifdef CONFIG_TQM5200_REV100 +#define CFG_I2C_MODULE 1 /* Select I2C module #1 for rev. 100 board */ +#else +#define CFG_I2C_MODULE 2 /* Select I2C module #2 for all other revs */ +#endif + +/* + * I2C clock frequency + * + * Please notice, that the resulting clock frequency could differ from the + * configured value. This is because the I2C clock is derived from system + * clock over a frequency divider with only a few divider values. U-boot + * calculates the best approximation for CFG_I2C_SPEED. However the calculated + * approximation allways lies below the configured value, never above. + */ +#define CFG_I2C_SPEED 100000 /* 100 kHz */ +#define CFG_I2C_SLAVE 0x7F + +/* + * EEPROM configuration for onboard EEPROM M24C32 (M24C64 should work + * also). For other EEPROMs configuration should be verified. On Mini-FAP the + * EEPROM (24C64) is on the same I2C address (but on other I2C bus), so the + * same configuration could be used. + */ +#define CFG_I2C_EEPROM_ADDR 0x50 /* 1010000x */ +#define CFG_I2C_EEPROM_ADDR_LEN 2 +#define CFG_EEPROM_PAGE_WRITE_BITS 5 /* =32 Bytes per write */ +#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 20 + +/* + * Flash configuration + */ +#define CFG_FLASH_BASE TEXT_BASE /* 0xFC000000 */ + +/* use CFI flash driver if no module variant is spezified */ +#define CFG_FLASH_CFI 1 /* Flash is CFI conformant */ +#define CFG_FLASH_CFI_DRIVER 1 /* Use the common driver */ +#define CFG_FLASH_BANKS_LIST { CFG_BOOTCS_START } +#define CFG_FLASH_EMPTY_INFO +#define CFG_FLASH_SIZE 0x04000000 /* 64 MByte */ +#define CFG_MAX_FLASH_SECT 512 /* max num of sects on one chip */ +#undef CFG_FLASH_USE_BUFFER_WRITE /* not supported yet for AMD */ + +#if !defined(CFG_LOWBOOT) +#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x00760000 + 0x00800000) +#else /* CFG_LOWBOOT */ +#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x00060000) +#endif /* CFG_LOWBOOT */ +#define CFG_MAX_FLASH_BANKS 1 /* max num of flash banks + (= chip selects) */ +#define CFG_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */ + +/* Dynamic MTD partition support */ +#define CONFIG_JFFS2_CMDLINE +#define MTDIDS_DEFAULT "nor0=TQM5200-0" +#define MTDPARTS_DEFAULT "mtdparts=TQM5200-0:640k(firmware)," \ + "1408k(kernel)," \ + "2m(initrd)," \ + "4m(small-fs)," \ + "16m(big-fs)," \ + "8m(misc)" + +/* + * Environment settings + */ +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_SIZE 0x10000 +#define CFG_ENV_SECT_SIZE 0x20000 +#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR + CFG_ENV_SECT_SIZE) +#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) + +/* + * Memory map + */ +#define CFG_MBAR 0xF0000000 +#define CFG_SDRAM_BASE 0x00000000 +#define CFG_DEFAULT_MBAR 0x80000000 + +/* Use ON-Chip SRAM until RAM will be available */ +#define CFG_INIT_RAM_ADDR MPC5XXX_SRAM +#ifdef CONFIG_POST +/* preserve space for the post_word at end of on-chip SRAM */ +#define CFG_INIT_RAM_END MPC5XXX_SRAM_POST_SIZE +#else +#define CFG_INIT_RAM_END MPC5XXX_SRAM_SIZE +#endif + + +#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +#define CFG_MONITOR_BASE TEXT_BASE +#if (CFG_MONITOR_BASE < CFG_FLASH_BASE) +# define CFG_RAMBOOT 1 +#endif + +#define CFG_MONITOR_LEN (384 << 10) /* Reserve 384 kB for Monitor */ +#define CFG_MALLOC_LEN (256 << 10) /* Reserve 256 kB for malloc() */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/* + * Ethernet configuration + */ +#define CONFIG_MPC5xxx_FEC 1 +/* + * Define CONFIG_FEC_10MBIT to force FEC at 10Mb + */ +/* #define CONFIG_FEC_10MBIT 1 */ +#define CONFIG_PHY_ADDR 0x00 + +/* + * GPIO configuration + * + * use pin gpio_wkup_6 as second SDRAM chip select (mem_cs1): + * Bit 0 (mask: 0x80000000): 1 + * use ALT CAN position: Bits 2-3 (mask: 0x30000000): + * 00 -> No Alternatives, CAN1/2 on PSC2 according to PSC2 setting. + * 01 -> CAN1 on I2C1, CAN2 on Tmr0/1. + * Use for REV200 STK52XX boards. Do not use with REV100 modules + * (because, there I2C1 is used as I2C bus) + * use PSC1 as UART: Bits 28-31 (mask: 0x00000007): 0100 + * use PSC2 as CAN: Bits 25:27 (mask: 0x00000030) + * 000 -> All PSC2 pins are GIOPs + * 001 -> CAN1/2 on PSC2 pins + * Use for REV100 STK52xx boards + * use PSC6: + * on STK52xx: + * use as UART. Pins PSC6_0 to PSC6_3 are used. + * Bits 9:11 (mask: 0x00700000): + * 101 -> PSC6 : Extended POST test is not available + * on MINI-FAP and TQM5200_IB: + * use PSC6_0 to PSC6_3 as GPIO: Bits 9:11 (mask: 0x00700000): + * 000 -> PSC6 could not be used as UART, CODEC or IrDA + * GPIO on PSC6_3 is used in post_hotkeys_pressed() to enable extended POST + * tests. + */ +#if defined (CONFIG_MINIFAP) +# define CFG_GPS_PORT_CONFIG 0x91000004 +#elif defined (CONFIG_STK52XX) +# if defined (CONFIG_STK52XX_REV100) +# define CFG_GPS_PORT_CONFIG 0x81500014 +# else /* STK52xx REV200 and above */ +# if defined (CONFIG_TQM5200_REV100) +# error TQM5200 REV100 not supported on STK52XX REV200 or above +# else/* TQM5200 REV200 and above */ +# define CFG_GPS_PORT_CONFIG 0x91500004 +# endif +# endif +#else /* TMQ5200 Inbetriebnahme-Board */ +# define CFG_GPS_PORT_CONFIG 0x81000004 +#endif + +/* + * RTC configuration + */ +#define CONFIG_RTC_MPC5200 1 /* use internal MPC5200 RTC */ + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +/* Enable an alternate, more extensive memory test */ +#define CFG_ALT_MEMTEST + +#define CFG_MEMTEST_START 0x00100000 /* memtest works on */ +#define CFG_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */ + +#define CFG_LOAD_ADDR 0x100000 /* default load address */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +/* + * Enable loopw commando. This has only affect, if CFG_CMD_MEM is defined, + * which is normally part of the default commands (CFV_CMD_DFL) + */ +#define CONFIG_LOOPW + +/* + * Various low-level settings + */ +#if defined(CONFIG_MPC5200) +#define CFG_HID0_INIT HID0_ICE | HID0_ICFI +#define CFG_HID0_FINAL HID0_ICE +#else +#define CFG_HID0_INIT 0 +#define CFG_HID0_FINAL 0 +#endif + +#define CFG_BOOTCS_START CFG_FLASH_BASE +#define CFG_BOOTCS_SIZE CFG_FLASH_SIZE +#ifdef CFG_PCISPEED_66 +#define CFG_BOOTCS_CFG 0x0008DF30 /* for pci_clk = 66 MHz */ +#else +#define CFG_BOOTCS_CFG 0x0004DF30 /* for pci_clk = 33 MHz */ +#endif +#define CFG_CS0_START CFG_FLASH_BASE +#define CFG_CS0_SIZE CFG_FLASH_SIZE + +#define CFG_CS_BURST 0x00000000 +#define CFG_CS_DEADCYCLE 0x33333311 /* 1 dead cycle for flash and SM501 */ + +#define CFG_RESET_ADDRESS 0xff000000 + +#endif /* __CONFIG_H */ -- cgit