From 80bae39aa32aeb801ba4fb0a284a958cd553e6f1 Mon Sep 17 00:00:00 2001 From: Masahiro Yamada Date: Fri, 30 May 2014 17:45:00 +0900 Subject: powerpc: ispan: remove orphan board This board has been orphan for a while. (Emails to its maintainer have been bouncing.) Because MPC82xx family is old enough, nobody would pick up the maintainership on it. Signed-off-by: Masahiro Yamada Cc: Wolfgang Denx --- include/configs/ISPAN.h | 330 ------------------------------------------------ 1 file changed, 330 deletions(-) delete mode 100644 include/configs/ISPAN.h (limited to 'include') diff --git a/include/configs/ISPAN.h b/include/configs/ISPAN.h deleted file mode 100644 index a2fdfd3274..0000000000 --- a/include/configs/ISPAN.h +++ /dev/null @@ -1,330 +0,0 @@ -/* - * Copyright (C) 2004 Arabella Software Ltd. - * Yuli Barcohen - * - * Support for Interphase iSPAN Communications Controllers - * (453x and others). Tested on 4532. - * - * Derived from iSPAN 4539 port (iphase4539) by - * Wolfgang Grandegger - * - * SPDX-License-Identifier: GPL-2.0+ - */ -#ifndef __CONFIG_H -#define __CONFIG_H - -#define CONFIG_ISPAN /* ...on one of Interphase iSPAN boards */ -#define CONFIG_CPM2 1 /* Has a CPM2 */ - -#define CONFIG_SYS_TEXT_BASE 0xFE7A0000 - -/*----------------------------------------------------------------------- - * Select serial console configuration - * - * If either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then - * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4 - * for SCC). - * - * If CONFIG_CONS_NONE is defined, then the serial console routines must be - * defined elsewhere (for example, on the cogent platform, there are serial - * ports on the motherboard which are used for the serial console - see - * cogent/cma101/serial.[ch]). - */ -#define CONFIG_CONS_ON_SMC /* Define if console on SMC */ -#undef CONFIG_CONS_ON_SCC /* Define if console on SCC */ -#undef CONFIG_CONS_NONE /* Define if console on something else */ -#define CONFIG_CONS_INDEX 1 /* Which serial channel for console */ - -/*----------------------------------------------------------------------- - * Select Ethernet configuration - * - * If either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then - * CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3 - * for FCC). - * - * If CONFIG_ETHER_NONE is defined, then either the Ethernet routines must - * be defined elsewhere (as for the console), or CONFIG_CMD_NET must be unset. - */ -#undef CONFIG_ETHER_ON_SCC /* Define if Ethernet on SCC */ -#define CONFIG_ETHER_ON_FCC /* Define if Ethernet on FCC */ -#undef CONFIG_ETHER_NONE /* Define if Ethernet on something else */ -#define CONFIG_ETHER_INDEX 3 /* Which channel for Ethernrt */ - -#ifdef CONFIG_ETHER_ON_FCC - -#if CONFIG_ETHER_INDEX == 3 - -#define CONFIG_SYS_PHY_ADDR 0 -#define CONFIG_SYS_CMXFCR_VALUE3 (CMXFCR_RF3CS_CLK14 | CMXFCR_TF3CS_CLK16) -#define CONFIG_SYS_CMXFCR_MASK3 (CMXFCR_FC3 | CMXFCR_RF3CS_MSK | CMXFCR_TF3CS_MSK) - -#endif /* CONFIG_ETHER_INDEX == 3 */ - -#define CONFIG_SYS_CPMFCR_RAMTYPE 0 -#define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB) - -#define CONFIG_MII /* MII PHY management */ -#define CONFIG_BITBANGMII /* Bit-bang MII PHY management */ -/* - * GPIO pins used for bit-banged MII communications - */ -#define MDIO_PORT 3 /* Port D */ -#define MDIO_DECLARE volatile ioport_t *iop = ioport_addr ( \ - (immap_t *) CONFIG_SYS_IMMR, MDIO_PORT ) -#define MDC_DECLARE MDIO_DECLARE - - -#define CONFIG_SYS_MDIO_PIN 0x00040000 /* PD13 */ -#define CONFIG_SYS_MDC_PIN 0x00080000 /* PD12 */ - -#define MDIO_ACTIVE (iop->pdir |= CONFIG_SYS_MDIO_PIN) -#define MDIO_TRISTATE (iop->pdir &= ~CONFIG_SYS_MDIO_PIN) -#define MDIO_READ ((iop->pdat & CONFIG_SYS_MDIO_PIN) != 0) - -#define MDIO(bit) if(bit) iop->pdat |= CONFIG_SYS_MDIO_PIN; \ - else iop->pdat &= ~CONFIG_SYS_MDIO_PIN - -#define MDC(bit) if(bit) iop->pdat |= CONFIG_SYS_MDC_PIN; \ - else iop->pdat &= ~CONFIG_SYS_MDC_PIN - -#define MIIDELAY udelay(1) - -#endif /* CONFIG_ETHER_ON_FCC */ - -#define CONFIG_8260_CLKIN 65536000 /* in Hz */ -#define CONFIG_BAUDRATE 38400 - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_IMMAP -#define CONFIG_CMD_MII -#define CONFIG_CMD_PING -#define CONFIG_CMD_REGINFO - - -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ -#define CONFIG_BOOTCOMMAND "bootm fe010000" /* autoboot command */ -#define CONFIG_BOOTARGS "root=/dev/ram rw" - -#define CONFIG_BZIP2 /* Include support for bzip2 compressed images */ -#undef CONFIG_WATCHDOG /* Disable platform specific watchdog */ - -/*----------------------------------------------------------------------- - * Miscellaneous configurable options - */ -#define CONFIG_SYS_HUSH_PARSER -#define CONFIG_SYS_LONGHELP /* #undef to save memory */ -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* Max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x03B00000 /* 1 ... 59 MB in SDRAM */ - -#define CONFIG_SYS_LOAD_ADDR 0x100000 /* Default load address */ - -#define CONFIG_SYS_RESET_ADDRESS 0x09900000 - -#define CONFIG_MISC_INIT_R /* We need misc_init_r() */ - -/*----------------------------------------------------------------------- - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE -#define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */ -#ifdef CONFIG_BZIP2 -#define CONFIG_SYS_MALLOC_LEN (4096 << 10) /* Reserve 4 MB for malloc() */ -#else -#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 KB for malloc() */ -#endif /* CONFIG_BZIP2 */ - -/*----------------------------------------------------------------------- - * FLASH organization - */ -#define CONFIG_SYS_FLASH_BASE 0xFE000000 -#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */ -#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */ -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* Max num of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 142 /* Max num of sects on one chip */ - -/* Environment is in flash, there is little space left in Serial EEPROM */ -#define CONFIG_ENV_IS_IN_FLASH -#define CONFIG_ENV_SECT_SIZE 0x10000 /* We use one complete sector */ -#define CONFIG_ENV_SIZE (CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) -#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) - -/*----------------------------------------------------------------------- - * Hard Reset Configuration Words - * - * If you change bits in the HRCW, you must also change the CONFIG_SYS_* - * defines for the various registers affected by the HRCW e.g. changing - * HRCW_DPPCxx requires you to also change CONFIG_SYS_SIUMCR. - */ -/* 0x1686B245 */ -#define CONFIG_SYS_HRCW_MASTER (HRCW_EBM | HRCW_BPS01 | HRCW_CIP |\ - HRCW_L2CPC10 | HRCW_ISB110 |\ - HRCW_BMS | HRCW_MMR11 | HRCW_APPC10 |\ - HRCW_CS10PC01 | HRCW_MODCK_H0101 \ - ) -/* No slaves */ -#define CONFIG_SYS_HRCW_SLAVE1 0 -#define CONFIG_SYS_HRCW_SLAVE2 0 -#define CONFIG_SYS_HRCW_SLAVE3 0 -#define CONFIG_SYS_HRCW_SLAVE4 0 -#define CONFIG_SYS_HRCW_SLAVE5 0 -#define CONFIG_SYS_HRCW_SLAVE6 0 -#define CONFIG_SYS_HRCW_SLAVE7 0 - -/*----------------------------------------------------------------------- - * Internal Memory Mapped Register - */ -#define CONFIG_SYS_IMMR 0xF0F00000 -#ifdef CONFIG_SYS_REV_B -#define CONFIG_SYS_DEFAULT_IMMR 0xFF000000 -#endif /* CONFIG_SYS_REV_B */ -/*----------------------------------------------------------------------- - * Definitions for initial stack pointer and data area (in DPRAM) - */ -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR -#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in DPRAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8260 CPU */ - -/*----------------------------------------------------------------------- - * HIDx - Hardware Implementation-dependent Registers 2-11 - *----------------------------------------------------------------------- - * HID0 also contains cache control. - * - * HID1 has only read-only information - nothing to set. - */ -#define CONFIG_SYS_HID0_INIT (HID0_ICE|HID0_DCE|HID0_ICFI|HID0_DCI|\ - HID0_IFEM|HID0_ABE) -#define CONFIG_SYS_HID0_FINAL (HID0_ICE|HID0_IFEM|HID0_ABE) -#define CONFIG_SYS_HID2 0 - -/*----------------------------------------------------------------------- - * RMR - Reset Mode Register 5-5 - *----------------------------------------------------------------------- - * turn on Checkstop Reset Enable - */ -#define CONFIG_SYS_RMR RMR_CSRE - -/*----------------------------------------------------------------------- - * BCR - Bus Configuration 4-25 - *----------------------------------------------------------------------- - */ -#define CONFIG_SYS_BCR 0xA01C0000 - -/*----------------------------------------------------------------------- - * SIUMCR - SIU Module Configuration 4-31 - *----------------------------------------------------------------------- - */ -#define CONFIG_SYS_SIUMCR 0x42250000/* 0x4205C000 */ - -/*----------------------------------------------------------------------- - * SYPCR - System Protection Control 4-35 - * SYPCR can only be written once after reset! - *----------------------------------------------------------------------- - * Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable - */ -#if defined (CONFIG_WATCHDOG) -#define CONFIG_SYS_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\ - SYPCR_SWRI|SYPCR_SWP|SYPCR_SWE) -#else -#define CONFIG_SYS_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\ - SYPCR_SWRI|SYPCR_SWP) -#endif /* CONFIG_WATCHDOG */ - -/*----------------------------------------------------------------------- - * TMCNTSC - Time Counter Status and Control 4-40 - * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk, - * and enable Time Counter - *----------------------------------------------------------------------- - */ -#define CONFIG_SYS_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE) - -/*----------------------------------------------------------------------- - * PISCR - Periodic Interrupt Status and Control 4-42 - *----------------------------------------------------------------------- - * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable - * Periodic timer - */ -#define CONFIG_SYS_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE) - -/*----------------------------------------------------------------------- - * SCCR - System Clock Control 9-8 - *----------------------------------------------------------------------- - * Ensure DFBRG is Divide by 16 - */ -#define CONFIG_SYS_SCCR SCCR_DFBRG01 - -/*----------------------------------------------------------------------- - * RCCR - RISC Controller Configuration 13-7 - *----------------------------------------------------------------------- - */ -#define CONFIG_SYS_RCCR 0 - -/*----------------------------------------------------------------------- - * Init Memory Controller: - * - * Bank Bus Machine PortSize Device - * ---- --- ------- ----------------------------- ------ - * 0 60x GPCM 8 bit (Rev.B)/16 bit (Rev.D) Flash - * 1 60x SDRAM 64 bit SDRAM - * 2 Local SDRAM 32 bit SDRAM - */ -#define CONFIG_SYS_USE_FIRMWARE /* If defined - do not initialise memory - controller, rely on initialisation - performed by the Interphase boot firmware. - */ - -#define CONFIG_SYS_OR0_PRELIM 0xFE000882 -#ifdef CONFIG_SYS_REV_B -#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | BRx_PS_8 | BRx_V) -#else /* Rev. D */ -#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | BRx_PS_16 | BRx_V) -#endif /* CONFIG_SYS_REV_B */ - -#define CONFIG_SYS_MPTPR 0x7F00 - -/* Please note that 60x SDRAM MUST start at 0 */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_60x_BR 0x00000041 -#define CONFIG_SYS_60x_OR 0xF0002CD0 -#define CONFIG_SYS_PSDMR 0x0049929A -#define CONFIG_SYS_PSRT 0x07 - -#define CONFIG_SYS_LSDRAM_BASE 0xF7000000 -#define CONFIG_SYS_LOC_BR 0x00001861 -#define CONFIG_SYS_LOC_OR 0xFF803280 -#define CONFIG_SYS_LSDMR 0x8285A552 -#define CONFIG_SYS_LSRT 0x07 - -#endif /* __CONFIG_H */ -- cgit