.. SPDX-License-Identifier: GPL-2.0+ HiFive Unleashed ================ FU540-C000 RISC-V SoC --------------------- The FU540-C000 is the world’s first 4+1 64-bit RISC-V SoC from SiFive. The HiFive Unleashed development platform is based on FU540-C000 and capable of running Linux. Mainline support ---------------- The support for following drivers are already enabled: 1. SiFive UART Driver. 2. SiFive PRCI Driver for clock. 3. Cadence MACB ethernet driver for networking support. TODO: 1. U-Boot expects the serial console device entry to be present under /chosen DT node. Without a serial console U-Boot will panic. Example: .. code-block:: none chosen { stdout-path = "/soc/serial@10010000:115200"; }; Building -------- 1. Add the RISC-V toolchain to your PATH. 2. Setup ARCH & cross compilation enviornment variable: .. code-block:: none export ARCH=riscv export CROSS_COMPILE= 3. make sifive_fu540_defconfig 4. make Flashing -------- The current U-Boot port is supported in S-mode only and loaded from DRAM. A prior stage (M-mode) firmware/bootloader (e.g OpenSBI or BBL) is required to load the u-boot.bin into memory and provide runtime services. The u-boot.bin can be given as a payload to the prior stage (M-mode) firmware/bootloader. The description of steps required to build the firmware is beyond the scope of this document. Please refer OpenSBI or BBL documenation. (Note: OpenSBI git repo is at https://github.com/riscv/opensbi.git) (Note: BBL git repo is at https://github.com/riscv/riscv-pk.git) Once the prior stage firmware/bootloader binary is generated, it should be copied to the first partition of the sdcard. .. code-block:: none sudo dd if= of=/dev/disk2s1 bs=1024 Booting ------- Once you plugin the sdcard and power up, you should see the U-Boot prompt. Sample boot log from HiFive Unleashed board ------------------------------------------- .. code-block:: none U-Boot 2019.01-00019-gc7953536-dirty (Jan 22 2019 - 11:05:40 -0800) CPU: rv64imafdc Model: sifive,hifive-unleashed-a00 DRAM: 8 GiB In: serial@10010000 Out: serial@10010000 Err: serial@10010000 Net: Warning: ethernet@10090000 (eth0) using random MAC address - b6:75:4d:48:50:94 eth0: ethernet@10090000 Hit any key to stop autoboot: 0 => version U-Boot 2019.01-00019-gc7953536-dirty (Jan 22 2019 - 11:05:40 -0800) riscv64-linux-gcc.br_real (Buildroot 2018.11-rc2-00003-ga0787e9) 8.2.0 GNU ld (GNU Binutils) 2.31.1 Now you can configure your networking, tftp server and use tftp boot method to load uImage. .. code-block:: none => setenv ethaddr 70:B3:D5:92:F0:C2 => setenv ipaddr 10.196.157.189 => setenv serverip 10.11.143.218 => setenv gatewayip 10.196.156.1 => setenv netmask 255.255.252.0 => bdinfo boot_params = 0x0000000000000000 DRAM bank = 0x0000000000000000 -> start = 0x0000000080000000 -> size = 0x0000000200000000 relocaddr = 0x00000000fff90000 reloc off = 0x000000007fd90000 ethaddr = 70:B3:D5:92:F0:C2 IP addr = 10.196.157.189 baudrate = 115200 bps => tftpboot uImage ethernet@10090000: PHY present at 0 ethernet@10090000: Starting autonegotiation... ethernet@10090000: Autonegotiation complete ethernet@10090000: link up, 1000Mbps full-duplex (lpa: 0x3800) Using ethernet@10090000 device TFTP from server 10.11.143.218; our IP address is 10.196.157.189; sending through gateway 10.196.156.1 Filename 'uImage'. Load address: 0x80200000 Loading: ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########################################################## 2.5 MiB/s done Bytes transferred = 14939132 (e3f3fc hex) => bootm 0x80200000 - 0x82200000 ## Booting kernel from Legacy Image at 80200000 ... Image Name: Linux Image Type: RISC-V Linux Kernel Image (uncompressed) Data Size: 14939068 Bytes = 14.2 MiB Load Address: 80200000 Entry Point: 80200000 Verifying Checksum ... OK ## Flattened Device Tree blob at 82200000 Booting using the fdt blob at 0x82200000 Loading Kernel Image ... OK Using Device Tree in place at 0000000082200000, end 0000000082205c69 Starting kernel ... [ 0.000000] OF: fdt: Ignoring memory range 0x80000000 - 0x80200000 [ 0.000000] Linux version 5.0.0-rc1-00020-g4b51f736 (atish@jedi-01) (gcc version 7.2.0 (GCC)) #262 SMP Mon Jan 21 17:39:27 PST 2019 [ 0.000000] initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] DMA32 [mem 0x0000000080200000-0x00000000ffffffff] [ 0.000000] Normal [mem 0x0000000100000000-0x000027ffffffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080200000-0x000000027fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080200000-0x000000027fffffff] [ 0.000000] software IO TLB: mapped [mem 0xfbfff000-0xfffff000] (64MB) [ 0.000000] CPU with hartid=0 has a non-okay status of "masked" [ 0.000000] CPU with hartid=0 has a non-okay status of "masked" [ 0.000000] elf_hwcap is 0x112d [ 0.000000] percpu: Embedded 15 pages/cpu @(____ptrval____) s29720 r0 d31720 u61440 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 2067975 [ 0.000000] Kernel command line: earlyprintk [ 0.000000] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes) [ 0.000000] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.000000] Sorting __ex_table... [ 0.000000] Memory: 8178760K/8386560K available (3309K kernel code, 248K rwdata, 872K rodata, 9381K init, 763K bss, 207800K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 0, nr_irqs: 0, preallocated irqs: 0 [ 0.000000] plic: mapped 53 interrupts to 4 (out of 9) handlers. [ 0.000000] riscv_timer_init_dt: Registering clocksource cpuid [0] hartid [1] [ 0.000000] clocksource: riscv_clocksource: mask: 0xffffffffffffffff max_cycles: 0x1d854df40, max_idle_ns: 3526361616960 ns [ 0.000008] sched_clock: 64 bits at 1000kHz, resolution 1000ns, wraps every 2199023255500ns [ 0.000221] Console: colour dummy device 80x25 [ 0.000902] printk: console [tty0] enabled [ 0.000963] Calibrating delay loop (skipped), value calculated using timer frequency.. 2.00 BogoMIPS (lpj=10000) [ 0.001034] pid_max: default: 32768 minimum: 301 [ 0.001541] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes) [ 0.001912] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes) [ 0.003542] rcu: Hierarchical SRCU implementation. [ 0.004347] smp: Bringing up secondary CPUs ... [ 1.040259] CPU1: failed to come online [ 2.080483] CPU2: failed to come online [ 3.120699] CPU3: failed to come online [ 3.120765] smp: Brought up 1 node, 1 CPU [ 3.121923] devtmpfs: initialized [ 3.124649] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 3.124727] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 3.125346] random: get_random_u32 called from bucket_table_alloc+0x72/0x172 with crng_init=0 [ 3.125578] NET: Registered protocol family 16 [ 3.126400] sifive-u54-prci 10000000.prci: Registered U54 core clocks [ 3.126649] sifive-gemgxl-mgmt 100a0000.cadence-gemgxl-mgmt: Registered clock switch 'cadence-gemgxl-mgmt' [ 3.135572] vgaarb: loaded [ 3.135858] SCSI subsystem initialized [ 3.136193] usbcore: registered new interface driver usbfs [ 3.136266] usbcore: registered new interface driver hub [ 3.136348] usbcore: registered new device driver usb [ 3.136446] pps_core: LinuxPPS API ver. 1 registered [ 3.136484] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 3.136575] PTP clock support registered [ 3.137256] clocksource: Switched to clocksource riscv_clocksource [ 3.142711] NET: Registered protocol family 2 [ 3.143322] tcp_listen_portaddr_hash hash table entries: 4096 (order: 4, 65536 bytes) [ 3.143634] TCP established hash table entries: 65536 (order: 7, 524288 bytes) [ 3.145799] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) [ 3.149121] TCP: Hash tables configured (established 65536 bind 65536) [ 3.149591] UDP hash table entries: 4096 (order: 5, 131072 bytes) [ 3.150094] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes) [ 3.150781] NET: Registered protocol family 1 [ 3.230693] workingset: timestamp_bits=62 max_order=21 bucket_order=0 [ 3.241224] io scheduler mq-deadline registered [ 3.241269] io scheduler kyber registered [ 3.242143] sifive_gpio 10060000.gpio: SiFive GPIO chip registered 16 GPIOs [ 3.242357] pwm-sifivem 10020000.pwm: Unable to find controller clock [ 3.242439] pwm-sifivem 10021000.pwm: Unable to find controller clock [ 3.243228] xilinx-pcie 2000000000.pci: PCIe Link is DOWN [ 3.243289] xilinx-pcie 2000000000.pci: host bridge /soc/pci@2000000000 ranges: [ 3.243360] xilinx-pcie 2000000000.pci: No bus range found for /soc/pci@2000000000, using [bus 00-ff] [ 3.243447] xilinx-pcie 2000000000.pci: MEM 0x40000000..0x5fffffff -> 0x40000000 [ 3.243591] xilinx-pcie 2000000000.pci: PCI host bridge to bus 0000:00 [ 3.243636] pci_bus 0000:00: root bus resource [bus 00-ff] [ 3.243676] pci_bus 0000:00: root bus resource [mem 0x40000000-0x5fffffff] [ 3.276547] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 3.277689] 10010000.serial: ttySIF0 at MMIO 0x10010000 (irq = 39, base_baud = 0) is a SiFive UART v0 [ 3.786963] printk: console [ttySIF0] enabled [ 3.791504] 10011000.serial: ttySIF1 at MMIO 0x10011000 (irq = 40, base_baud = 0) is a SiFive UART v0 [ 3.801251] sifive_spi 10040000.spi: mapped; irq=41, cs=1 [ 3.806362] m25p80 spi0.0: unrecognized JEDEC id bytes: 9d, 70, 19 [ 3.812084] m25p80: probe of spi0.0 failed with error -2 [ 3.817453] sifive_spi 10041000.spi: mapped; irq=42, cs=4 [ 3.823027] sifive_spi 10050000.spi: mapped; irq=43, cs=1 [ 3.828604] libphy: Fixed MDIO Bus: probed [ 3.832623] macb: GEM doesn't support hardware ptp. [ 3.837196] libphy: MACB_mii_bus: probed [ 4.041156] Microsemi VSC8541 SyncE 10090000.ethernet-ffffffff:00: attached PHY driver [Microsemi VSC8541 SyncE] (mii_bus:phy_addr=10090000.ethernet-ffffffff:00, irq=POLL) [ 4.055779] macb 10090000.ethernet eth0: Cadence GEM rev 0x10070109 at 0x10090000 irq 12 (70:b3:d5:92:f0:c2) [ 4.065780] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 4.072033] ehci-pci: EHCI PCI platform driver [ 4.076521] usbcore: registered new interface driver usb-storage [ 4.082843] softdog: initialized. soft_noboot=0 soft_margin=60 sec soft_panic=0 (nowayout=0) [ 4.127465] mmc_spi spi2.0: SD/MMC host mmc0, no DMA, no WP, no poweroff [ 4.133645] usbcore: registered new interface driver usbhid [ 4.138980] usbhid: USB HID core driver [ 4.143017] NET: Registered protocol family 17 [ 4.147885] pwm-sifivem 10020000.pwm: SiFive PWM chip registered 4 PWMs [ 4.153945] pwm-sifivem 10021000.pwm: SiFive PWM chip registered 4 PWMs [ 4.186407] Freeing unused kernel memory: 9380K [ 4.190224] This architecture does not have kernel memory protection. [ 4.196609] Run /init as init process Starting logging: OK Starting mdev... [ 4.303785] mmc0: host does not support reading read-only switch, assuming write-enable [ 4.311109] mmc0: new SDHC card on SPI [ 4.317103] mmcblk0: mmc0:0000 SS08G 7.40 GiB [ 4.386471] mmcblk0: p1 p2 sort: /sys/devices/platform/Fixed: No such file or directory modprobe: can't change directory to '/lib/modules': No such file or directory Initializing random[ 4.759075] random: dd: uninitialized urandom read (512 bytes read) number generator... done. Starting network... udhcpc (v1.24.2) started Sending discover... Sending discover... [ 7.927510] macb 10090000.ethernet eth0: link up (1000/Full) Sending discover... Sending select for 10.196.157.190... Lease of 10.196.157.190 obtained, lease time 499743 deleting routers adding dns 10.86.1.1 adding dns 10.86.2.1 /etc/init.d/S50dropbear Starting dropbear sshd: [ 12.772393] random: dropbear: uninitialized urandom read (32 bytes read) OK Welcome to Buildroot buildroot login: