// SPDX-License-Identifier: GPL-2.0+ /* * Freescale i.MX28 NAND flash driver * * Copyright (C) 2011 Marek Vasut * on behalf of DENX Software Engineering GmbH * * Based on code from LTIB: * Freescale GPMI NFC NAND Flash Driver * * Copyright (C) 2010 Freescale Semiconductor, Inc. * Copyright (C) 2008 Embedded Alley Solutions, Inc. * Copyright 2017-2019 NXP */ #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #define MXS_NAND_DMA_DESCRIPTOR_COUNT 4 #if defined(CONFIG_MX6) || defined(CONFIG_MX7) || defined(CONFIG_IMX8) || \ defined(CONFIG_IMX8M) #define MXS_NAND_CHUNK_DATA_CHUNK_SIZE_SHIFT 2 #else #define MXS_NAND_CHUNK_DATA_CHUNK_SIZE_SHIFT 0 #endif #define MXS_NAND_METADATA_SIZE 10 #define MXS_NAND_BITS_PER_ECC_LEVEL 13 #if !defined(CONFIG_SYS_CACHELINE_SIZE) || CONFIG_SYS_CACHELINE_SIZE < 32 #define MXS_NAND_COMMAND_BUFFER_SIZE 32 #else #define MXS_NAND_COMMAND_BUFFER_SIZE CONFIG_SYS_CACHELINE_SIZE #endif #define MXS_NAND_BCH_TIMEOUT 10000 struct nand_ecclayout fake_ecc_layout; /* * Cache management functions */ #if !CONFIG_IS_ENABLED(SYS_DCACHE_OFF) static void mxs_nand_flush_data_buf(struct mxs_nand_info *info) { uint32_t addr = (uintptr_t)info->data_buf; flush_dcache_range(addr, addr + info->data_buf_size); } static void mxs_nand_inval_data_buf(struct mxs_nand_info *info) { uint32_t addr = (uintptr_t)info->data_buf; invalidate_dcache_range(addr, addr + info->data_buf_size); } static void mxs_nand_flush_cmd_buf(struct mxs_nand_info *info) { uint32_t addr = (uintptr_t)info->cmd_buf; flush_dcache_range(addr, addr + MXS_NAND_COMMAND_BUFFER_SIZE); } #else static inline void mxs_nand_flush_data_buf(struct mxs_nand_info *info) {} static inline void mxs_nand_inval_data_buf(struct mxs_nand_info *info) {} static inline void mxs_nand_flush_cmd_buf(struct mxs_nand_info *info) {} #endif static struct mxs_dma_desc *mxs_nand_get_dma_desc(struct mxs_nand_info *info) { struct mxs_dma_desc *desc; if (info->desc_index >= MXS_NAND_DMA_DESCRIPTOR_COUNT) { printf("MXS NAND: Too many DMA descriptors requested\n"); return NULL; } desc = info->desc[info->desc_index]; info->desc_index++; return desc; } static void mxs_nand_return_dma_descs(struct mxs_nand_info *info) { int i; struct mxs_dma_desc *desc; for (i = 0; i < info->desc_index; i++) { desc = info->desc[i]; memset(desc, 0, sizeof(struct mxs_dma_desc)); desc->address = (dma_addr_t)desc; } info->desc_index = 0; } static uint32_t mxs_nand_aux_status_offset(void) { return (MXS_NAND_METADATA_SIZE + 0x3) & ~0x3; } static inline bool mxs_nand_bbm_in_data_chunk(struct bch_geometry *geo, struct mtd_info *mtd, unsigned int *chunk_num) { unsigned int i, j; if (geo->ecc_chunk0_size != geo->ecc_chunkn_size) { dev_err(this->dev, "The size of chunk0 must equal to chunkn\n"); return false; } i = (mtd->writesize * 8 - MXS_NAND_METADATA_SIZE * 8) / (geo->gf_len * geo->ecc_strength + geo->ecc_chunkn_size * 8); j = (mtd->writesize * 8 - MXS_NAND_METADATA_SIZE * 8) - (geo->gf_len * geo->ecc_strength + geo->ecc_chunkn_size * 8) * i; if (j < geo->ecc_chunkn_size * 8) { *chunk_num = i + 1; dev_dbg(this->dev, "Set ecc to %d and bbm in chunk %d\n", geo->ecc_strength, *chunk_num); return true; } return false; } static inline int mxs_nand_calc_ecc_layout_by_info(struct bch_geometry *geo, struct mtd_info *mtd, unsigned int ecc_strength, unsigned int ecc_step) { struct nand_chip *chip = mtd_to_nand(mtd); struct mxs_nand_info *nand_info = nand_get_controller_data(chip); unsigned int block_mark_bit_offset; switch (ecc_step) { case SZ_512: geo->gf_len = 13; break; case SZ_1K: geo->gf_len = 14; break; default: return -EINVAL; } geo->ecc_chunk0_size = ecc_step; geo->ecc_chunkn_size = ecc_step; geo->ecc_strength = round_up(ecc_strength, 2); /* Keep the C >= O */ if (geo->ecc_chunkn_size < mtd->oobsize) return -EINVAL; if (geo->ecc_strength > nand_info->max_ecc_strength_supported) return -EINVAL; geo->ecc_chunk_count = mtd->writesize / geo->ecc_chunkn_size; /* For bit swap. */ block_mark_bit_offset = mtd->writesize * 8 - (geo->ecc_strength * geo->gf_len * (geo->ecc_chunk_count - 1) + MXS_NAND_METADATA_SIZE * 8); geo->block_mark_byte_offset = block_mark_bit_offset / 8; geo->block_mark_bit_offset = block_mark_bit_offset % 8; return 0; } static inline int mxs_nand_legacy_calc_ecc_layout(struct bch_geometry *geo, struct mtd_info *mtd) { struct nand_chip *chip = mtd_to_nand(mtd); struct mxs_nand_info *nand_info = nand_get_controller_data(chip); unsigned int block_mark_bit_offset; /* The default for the length of Galois Field. */ geo->gf_len = 13; /* The default for chunk size. */ geo->ecc_chunk0_size = 512; geo->ecc_chunkn_size = 512; if (geo->ecc_chunkn_size < mtd->oobsize) { geo->gf_len = 14; geo->ecc_chunk0_size *= 2; geo->ecc_chunkn_size *= 2; } geo->ecc_chunk_count = mtd->writesize / geo->ecc_chunkn_size; /* * Determine the ECC layout with the formula: * ECC bits per chunk = (total page spare data bits) / * (bits per ECC level) / (chunks per page) * where: * total page spare data bits = * (page oob size - meta data size) * (bits per byte) */ geo->ecc_strength = ((mtd->oobsize - MXS_NAND_METADATA_SIZE) * 8) / (geo->gf_len * geo->ecc_chunk_count); geo->ecc_strength = min(round_down(geo->ecc_strength, 2), nand_info->max_ecc_strength_supported); block_mark_bit_offset = mtd->writesize * 8 - (geo->ecc_strength * geo->gf_len * (geo->ecc_chunk_count - 1) + MXS_NAND_METADATA_SIZE * 8); geo->block_mark_byte_offset = block_mark_bit_offset / 8; geo->block_mark_bit_offset = block_mark_bit_offset % 8; return 0; } static inline int mxs_nand_calc_ecc_for_large_oob(struct bch_geometry *geo, struct mtd_info *mtd) { struct nand_chip *chip = mtd_to_nand(mtd); struct mxs_nand_info *nand_info = nand_get_controller_data(chip); unsigned int block_mark_bit_offset; unsigned int max_ecc; unsigned int bbm_chunk; unsigned int i; /* sanity check for the minimum ecc nand required */ if (!(chip->ecc_strength_ds > 0 && chip->ecc_step_ds > 0)) return -EINVAL; geo->ecc_strength = chip->ecc_strength_ds; /* calculate the maximum ecc platform can support*/ geo->gf_len = 14; geo->ecc_chunk0_size = 1024; geo->ecc_chunkn_size = 1024; geo->ecc_chunk_count = mtd->writesize / geo->ecc_chunkn_size; max_ecc = ((mtd->oobsize - MXS_NAND_METADATA_SIZE) * 8) / (geo->gf_len * geo->ecc_chunk_count); max_ecc = min(round_down(max_ecc, 2), nand_info->max_ecc_strength_supported); /* search a supported ecc strength that makes bbm */ /* located in data chunk */ geo->ecc_strength = chip->ecc_strength_ds; while (!(geo->ecc_strength > max_ecc)) { if (mxs_nand_bbm_in_data_chunk(geo, mtd, &bbm_chunk)) break; geo->ecc_strength += 2; } /* if none of them works, keep using the minimum ecc */ /* nand required but changing ecc page layout */ if (geo->ecc_strength > max_ecc) { geo->ecc_strength = chip->ecc_strength_ds; /* add extra ecc for meta data */ geo->ecc_chunk0_size = 0; geo->ecc_chunk_count = (mtd->writesize / geo->ecc_chunkn_size) + 1; geo->ecc_for_meta = 1; /* check if oob can afford this extra ecc chunk */ if (mtd->oobsize * 8 < MXS_NAND_METADATA_SIZE * 8 + geo->gf_len * geo->ecc_strength * geo->ecc_chunk_count) { printf("unsupported NAND chip with new layout\n"); return -EINVAL; } /* calculate in which chunk bbm located */ bbm_chunk = (mtd->writesize * 8 - MXS_NAND_METADATA_SIZE * 8 - geo->gf_len * geo->ecc_strength) / (geo->gf_len * geo->ecc_strength + geo->ecc_chunkn_size * 8) + 1; } /* calculate the number of ecc chunk behind the bbm */ i = (mtd->writesize / geo->ecc_chunkn_size) - bbm_chunk + 1; block_mark_bit_offset = mtd->writesize * 8 - (geo->ecc_strength * geo->gf_len * (geo->ecc_chunk_count - i) + MXS_NAND_METADATA_SIZE * 8); geo->block_mark_byte_offset = block_mark_bit_offset / 8; geo->block_mark_bit_offset = block_mark_bit_offset % 8; return 0; } /* * Wait for BCH complete IRQ and clear the IRQ */ static int mxs_nand_wait_for_bch_complete(struct mxs_nand_info *nand_info) { int timeout = MXS_NAND_BCH_TIMEOUT; int ret; ret = mxs_wait_mask_set(&nand_info->bch_regs->hw_bch_ctrl_reg, BCH_CTRL_COMPLETE_IRQ, timeout); writel(BCH_CTRL_COMPLETE_IRQ, &nand_info->bch_regs->hw_bch_ctrl_clr); return ret; } /* * This is the function that we install in the cmd_ctrl function pointer of the * owning struct nand_chip. The only functions in the reference implementation * that use these functions pointers are cmdfunc and select_chip. * * In this driver, we implement our own select_chip, so this function will only * be called by the reference implementation's cmdfunc. For this reason, we can * ignore the chip enable bit and concentrate only on sending bytes to the NAND * Flash. */ static void mxs_nand_cmd_ctrl(struct mtd_info *mtd, int data, unsigned int ctrl) { struct nand_chip *nand = mtd_to_nand(mtd); struct mxs_nand_info *nand_info = nand_get_controller_data(nand); struct mxs_dma_desc *d; uint32_t channel = MXS_DMA_CHANNEL_AHB_APBH_GPMI0 + nand_info->cur_chip; int ret; /* * If this condition is true, something is _VERY_ wrong in MTD * subsystem! */ if (nand_info->cmd_queue_len == MXS_NAND_COMMAND_BUFFER_SIZE) { printf("MXS NAND: Command queue too long\n"); return; } /* * Every operation begins with a command byte and a series of zero or * more address bytes. These are distinguished by either the Address * Latch Enable (ALE) or Command Latch Enable (CLE) signals being * asserted. When MTD is ready to execute the command, it will * deasert both latch enables. * * Rather than run a separate DMA operation for every single byte, we * queue them up and run a single DMA operation for the entire series * of command and data bytes. */ if (ctrl & (NAND_ALE | NAND_CLE)) { if (data != NAND_CMD_NONE) nand_info->cmd_buf[nand_info->cmd_queue_len++] = data; return; } /* * If control arrives here, MTD has deasserted both the ALE and CLE, * which means it's ready to run an operation. Check if we have any * bytes to send. */ if (nand_info->cmd_queue_len == 0) return; /* Compile the DMA descriptor -- a descriptor that sends command. */ d = mxs_nand_get_dma_desc(nand_info); d->cmd.data = MXS_DMA_DESC_COMMAND_DMA_READ | MXS_DMA_DESC_IRQ | MXS_DMA_DESC_CHAIN | MXS_DMA_DESC_DEC_SEM | MXS_DMA_DESC_WAIT4END | (3 << MXS_DMA_DESC_PIO_WORDS_OFFSET) | (nand_info->cmd_queue_len << MXS_DMA_DESC_BYTES_OFFSET); d->cmd.address = (dma_addr_t)nand_info->cmd_buf; d->cmd.pio_words[0] = GPMI_CTRL0_COMMAND_MODE_WRITE | GPMI_CTRL0_WORD_LENGTH | (nand_info->cur_chip << GPMI_CTRL0_CS_OFFSET) | GPMI_CTRL0_ADDRESS_NAND_CLE | GPMI_CTRL0_ADDRESS_INCREMENT | nand_info->cmd_queue_len; mxs_dma_desc_append(channel, d); /* Flush caches */ mxs_nand_flush_cmd_buf(nand_info); /* Execute the DMA chain. */ ret = mxs_dma_go(channel); if (ret) printf("MXS NAND: Error sending command\n"); mxs_nand_return_dma_descs(nand_info); /* Reset the command queue. */ nand_info->cmd_queue_len = 0; } /* * Test if the NAND flash is ready. */ static int mxs_nand_device_ready(struct mtd_info *mtd) { struct nand_chip *chip = mtd_to_nand(mtd); struct mxs_nand_info *nand_info = nand_get_controller_data(chip); uint32_t tmp; tmp = readl(&nand_info->gpmi_regs->hw_gpmi_stat); tmp >>= (GPMI_STAT_READY_BUSY_OFFSET + nand_info->cur_chip); return tmp & 1; } /* * Select the NAND chip. */ static void mxs_nand_select_chip(struct mtd_info *mtd, int chip) { struct nand_chip *nand = mtd_to_nand(mtd); struct mxs_nand_info *nand_info = nand_get_controller_data(nand); nand_info->cur_chip = chip; } /* * Handle block mark swapping. * * Note that, when this function is called, it doesn't know whether it's * swapping the block mark, or swapping it *back* -- but it doesn't matter * because the the operation is the same. */ static void mxs_nand_swap_block_mark(struct bch_geometry *geo, uint8_t *data_buf, uint8_t *oob_buf) { uint32_t bit_offset = geo->block_mark_bit_offset; uint32_t buf_offset = geo->block_mark_byte_offset; uint32_t src; uint32_t dst; /* * Get the byte from the data area that overlays the block mark. Since * the ECC engine applies its own view to the bits in the page, the * physical block mark won't (in general) appear on a byte boundary in * the data. */ src = data_buf[buf_offset] >> bit_offset; src |= data_buf[buf_offset + 1] << (8 - bit_offset); dst = oob_buf[0]; oob_buf[0] = src; data_buf[buf_offset] &= ~(0xff << bit_offset); data_buf[buf_offset + 1] &= 0xff << bit_offset; data_buf[buf_offset] |= dst << bit_offset; data_buf[buf_offset + 1] |= dst >> (8 - bit_offset); } /* * Read data from NAND. */ static void mxs_nand_read_buf(struct mtd_info *mtd, uint8_t *buf, int length) { struct nand_chip *nand = mtd_to_nand(mtd); struct mxs_nand_info *nand_info = nand_get_controller_data(nand); struct mxs_dma_desc *d; uint32_t channel = MXS_DMA_CHANNEL_AHB_APBH_GPMI0 + nand_info->cur_chip; int ret; if (length > NAND_MAX_PAGESIZE) { printf("MXS NAND: DMA buffer too big\n"); return; } if (!buf) { printf("MXS NAND: DMA buffer is NULL\n"); return; } /* Compile the DMA descriptor - a descriptor that reads data. */ d = mxs_nand_get_dma_desc(nand_info); d->cmd.data = MXS_DMA_DESC_COMMAND_DMA_WRITE | MXS_DMA_DESC_IRQ | MXS_DMA_DESC_DEC_SEM | MXS_DMA_DESC_WAIT4END | (1 << MXS_DMA_DESC_PIO_WORDS_OFFSET) | (length << MXS_DMA_DESC_BYTES_OFFSET); d->cmd.address = (dma_addr_t)nand_info->data_buf; d->cmd.pio_words[0] = GPMI_CTRL0_COMMAND_MODE_READ | GPMI_CTRL0_WORD_LENGTH | (nand_info->cur_chip << GPMI_CTRL0_CS_OFFSET) | GPMI_CTRL0_ADDRESS_NAND_DATA | length; mxs_dma_desc_append(channel, d); /* * A DMA descriptor that waits for the command to end and the chip to * become ready. * * I think we actually should *not* be waiting for the chip to become * ready because, after all, we don't care. I think the original code * did that and no one has re-thought it yet. */ d = mxs_nand_get_dma_desc(nand_info); d->cmd.data = MXS_DMA_DESC_COMMAND_NO_DMAXFER | MXS_DMA_DESC_IRQ | MXS_DMA_DESC_NAND_WAIT_4_READY | MXS_DMA_DESC_DEC_SEM | MXS_DMA_DESC_WAIT4END | (1 << MXS_DMA_DESC_PIO_WORDS_OFFSET); d->cmd.address = 0; d->cmd.pio_words[0] = GPMI_CTRL0_COMMAND_MODE_WAIT_FOR_READY | GPMI_CTRL0_WORD_LENGTH | (nand_info->cur_chip << GPMI_CTRL0_CS_OFFSET) | GPMI_CTRL0_ADDRESS_NAND_DATA; mxs_dma_desc_append(channel, d); /* Invalidate caches */ mxs_nand_inval_data_buf(nand_info); /* Execute the DMA chain. */ ret = mxs_dma_go(channel); if (ret) { printf("MXS NAND: DMA read error\n"); goto rtn; } /* Invalidate caches */ mxs_nand_inval_data_buf(nand_info); memcpy(buf, nand_info->data_buf, length); rtn: mxs_nand_return_dma_descs(nand_info); } /* * Write data to NAND. */ static void mxs_nand_write_buf(struct mtd_info *mtd, const uint8_t *buf, int length) { struct nand_chip *nand = mtd_to_nand(mtd); struct mxs_nand_info *nand_info = nand_get_controller_data(nand); struct mxs_dma_desc *d; uint32_t channel = MXS_DMA_CHANNEL_AHB_APBH_GPMI0 + nand_info->cur_chip; int ret; if (length > NAND_MAX_PAGESIZE) { printf("MXS NAND: DMA buffer too big\n"); return; } if (!buf) { printf("MXS NAND: DMA buffer is NULL\n"); return; } memcpy(nand_info->data_buf, buf, length); /* Compile the DMA descriptor - a descriptor that writes data. */ d = mxs_nand_get_dma_desc(nand_info); d->cmd.data = MXS_DMA_DESC_COMMAND_DMA_READ | MXS_DMA_DESC_IRQ | MXS_DMA_DESC_DEC_SEM | MXS_DMA_DESC_WAIT4END | (1 << MXS_DMA_DESC_PIO_WORDS_OFFSET) | (length << MXS_DMA_DESC_BYTES_OFFSET); d->cmd.address = (dma_addr_t)nand_info->data_buf; d->cmd.pio_words[0] = GPMI_CTRL0_COMMAND_MODE_WRITE | GPMI_CTRL0_WORD_LENGTH | (nand_info->cur_chip << GPMI_CTRL0_CS_OFFSET) | GPMI_CTRL0_ADDRESS_NAND_DATA | length; mxs_dma_desc_append(channel, d); /* Flush caches */ mxs_nand_flush_data_buf(nand_info); /* Execute the DMA chain. */ ret = mxs_dma_go(channel); if (ret) printf("MXS NAND: DMA write error\n"); mxs_nand_return_dma_descs(nand_info); } /* * Read a single byte from NAND. */ static uint8_t mxs_nand_read_byte(struct mtd_info *mtd) { uint8_t buf; mxs_nand_read_buf(mtd, &buf, 1); return buf; } static bool mxs_nand_erased_page(struct mtd_info *mtd, struct nand_chip *nand, u8 *buf, int chunk, int page) { struct mxs_nand_info *nand_info = nand_get_controller_data(nand); struct bch_geometry *geo = &nand_info->bch_geometry; unsigned int flip_bits = 0, flip_bits_noecc = 0; unsigned int threshold; unsigned int base = geo->ecc_chunkn_size * chunk; u32 *dma_buf = (u32 *)buf; int i; threshold = geo->gf_len / 2; if (threshold > geo->ecc_strength) threshold = geo->ecc_strength; for (i = 0; i < geo->ecc_chunkn_size; i++) { flip_bits += hweight8(~buf[base + i]); if (flip_bits > threshold) return false; } nand->cmdfunc(mtd, NAND_CMD_READ0, 0, page); nand->read_buf(mtd, buf, mtd->writesize); for (i = 0; i < mtd->writesize / 4; i++) { flip_bits_noecc += hweight32(~dma_buf[i]); if (flip_bits_noecc > threshold) return false; } mtd->ecc_stats.corrected += flip_bits; memset(buf, 0xff, mtd->writesize); printf("The page(%d) is an erased page(%d,%d,%d,%d).\n", page, chunk, threshold, flip_bits, flip_bits_noecc); return true; } /* * Read a page from NAND. */ static int mxs_nand_ecc_read_page(struct mtd_info *mtd, struct nand_chip *nand, uint8_t *buf, int oob_required, int page) { struct mxs_nand_info *nand_info = nand_get_controller_data(nand); struct bch_geometry *geo = &nand_info->bch_geometry; struct mxs_bch_regs *bch_regs = nand_info->bch_regs; struct mxs_dma_desc *d; uint32_t channel = MXS_DMA_CHANNEL_AHB_APBH_GPMI0 + nand_info->cur_chip; uint32_t corrected = 0, failed = 0; uint8_t *status; int i, ret; int flag = 0; /* Compile the DMA descriptor - wait for ready. */ d = mxs_nand_get_dma_desc(nand_info); d->cmd.data = MXS_DMA_DESC_COMMAND_NO_DMAXFER | MXS_DMA_DESC_CHAIN | MXS_DMA_DESC_NAND_WAIT_4_READY | MXS_DMA_DESC_WAIT4END | (1 << MXS_DMA_DESC_PIO_WORDS_OFFSET); d->cmd.address = 0; d->cmd.pio_words[0] = GPMI_CTRL0_COMMAND_MODE_WAIT_FOR_READY | GPMI_CTRL0_WORD_LENGTH | (nand_info->cur_chip << GPMI_CTRL0_CS_OFFSET) | GPMI_CTRL0_ADDRESS_NAND_DATA; mxs_dma_desc_append(channel, d); /* Compile the DMA descriptor - enable the BCH block and read. */ d = mxs_nand_get_dma_desc(nand_info); d->cmd.data = MXS_DMA_DESC_COMMAND_NO_DMAXFER | MXS_DMA_DESC_CHAIN | MXS_DMA_DESC_WAIT4END | (6 << MXS_DMA_DESC_PIO_WORDS_OFFSET); d->cmd.address = 0; d->cmd.pio_words[0] = GPMI_CTRL0_COMMAND_MODE_READ | GPMI_CTRL0_WORD_LENGTH | (nand_info->cur_chip << GPMI_CTRL0_CS_OFFSET) | GPMI_CTRL0_ADDRESS_NAND_DATA | (mtd->writesize + mtd->oobsize); d->cmd.pio_words[1] = 0; d->cmd.pio_words[2] = GPMI_ECCCTRL_ENABLE_ECC | GPMI_ECCCTRL_ECC_CMD_DECODE | GPMI_ECCCTRL_BUFFER_MASK_BCH_PAGE; d->cmd.pio_words[3] = mtd->writesize + mtd->oobsize; d->cmd.pio_words[4] = (dma_addr_t)nand_info->data_buf; d->cmd.pio_words[5] = (dma_addr_t)nand_info->oob_buf; if (nand_info->en_randomizer) { d->cmd.pio_words[2] |= GPMI_ECCCTRL_RANDOMIZER_ENABLE | GPMI_ECCCTRL_RANDOMIZER_TYPE2; d->cmd.pio_words[3] |= (page % 256) << 16; } mxs_dma_desc_append(channel, d); /* Compile the DMA descriptor - disable the BCH block. */ d = mxs_nand_get_dma_desc(nand_info); d->cmd.data = MXS_DMA_DESC_COMMAND_NO_DMAXFER | MXS_DMA_DESC_CHAIN | MXS_DMA_DESC_NAND_WAIT_4_READY | MXS_DMA_DESC_WAIT4END | (3 << MXS_DMA_DESC_PIO_WORDS_OFFSET); d->cmd.address = 0; d->cmd.pio_words[0] = GPMI_CTRL0_COMMAND_MODE_WAIT_FOR_READY | GPMI_CTRL0_WORD_LENGTH | (nand_info->cur_chip << GPMI_CTRL0_CS_OFFSET) | GPMI_CTRL0_ADDRESS_NAND_DATA | (mtd->writesize + mtd->oobsize); d->cmd.pio_words[1] = 0; d->cmd.pio_words[2] = 0; mxs_dma_desc_append(channel, d); /* Compile the DMA descriptor - deassert the NAND lock and interrupt. */ d = mxs_nand_get_dma_desc(nand_info); d->cmd.data = MXS_DMA_DESC_COMMAND_NO_DMAXFER | MXS_DMA_DESC_IRQ | MXS_DMA_DESC_DEC_SEM; d->cmd.address = 0; mxs_dma_desc_append(channel, d); /* Invalidate caches */ mxs_nand_inval_data_buf(nand_info); /* Execute the DMA chain. */ ret = mxs_dma_go(channel); if (ret) { printf("MXS NAND: DMA read error\n"); goto rtn; } ret = mxs_nand_wait_for_bch_complete(nand_info); if (ret) { printf("MXS NAND: BCH read timeout\n"); goto rtn; } mxs_nand_return_dma_descs(nand_info); /* Invalidate caches */ mxs_nand_inval_data_buf(nand_info); /* Read DMA completed, now do the mark swapping. */ mxs_nand_swap_block_mark(geo, nand_info->data_buf, nand_info->oob_buf); /* Loop over status bytes, accumulating ECC status. */ status = nand_info->oob_buf + mxs_nand_aux_status_offset(); for (i = 0; i < geo->ecc_chunk_count; i++) { if (status[i] == 0x00) continue; if (status[i] == 0xff) { if (!nand_info->en_randomizer && (is_mx6dqp() || is_mx7() || is_mx6ul() || is_imx8() || is_imx8m())) if (readl(&bch_regs->hw_bch_debug1)) flag = 1; continue; } if (status[i] == 0xfe) { if (mxs_nand_erased_page(mtd, nand, nand_info->data_buf, i, page)) break; failed++; continue; } corrected += status[i]; } /* Propagate ECC status to the owning MTD. */ mtd->ecc_stats.failed += failed; mtd->ecc_stats.corrected += corrected; /* * It's time to deliver the OOB bytes. See mxs_nand_ecc_read_oob() for * details about our policy for delivering the OOB. * * We fill the caller's buffer with set bits, and then copy the block * mark to the caller's buffer. Note that, if block mark swapping was * necessary, it has already been done, so we can rely on the first * byte of the auxiliary buffer to contain the block mark. */ memset(nand->oob_poi, 0xff, mtd->oobsize); nand->oob_poi[0] = nand_info->oob_buf[0]; memcpy(buf, nand_info->data_buf, mtd->writesize); if (flag) memset(buf, 0xff, mtd->writesize); rtn: mxs_nand_return_dma_descs(nand_info); return ret; } /* * Write a page to NAND. */ static int mxs_nand_ecc_write_page(struct mtd_info *mtd, struct nand_chip *nand, const uint8_t *buf, int oob_required, int page) { struct mxs_nand_info *nand_info = nand_get_controller_data(nand); struct bch_geometry *geo = &nand_info->bch_geometry; struct mxs_dma_desc *d; uint32_t channel = MXS_DMA_CHANNEL_AHB_APBH_GPMI0 + nand_info->cur_chip; int ret; memcpy(nand_info->data_buf, buf, mtd->writesize); memcpy(nand_info->oob_buf, nand->oob_poi, mtd->oobsize); /* Handle block mark swapping. */ mxs_nand_swap_block_mark(geo, nand_info->data_buf, nand_info->oob_buf); /* Compile the DMA descriptor - write data. */ d = mxs_nand_get_dma_desc(nand_info); d->cmd.data = MXS_DMA_DESC_COMMAND_NO_DMAXFER | MXS_DMA_DESC_IRQ | MXS_DMA_DESC_DEC_SEM | MXS_DMA_DESC_WAIT4END | (6 << MXS_DMA_DESC_PIO_WORDS_OFFSET); d->cmd.address = 0; d->cmd.pio_words[0] = GPMI_CTRL0_COMMAND_MODE_WRITE | GPMI_CTRL0_WORD_LENGTH | (nand_info->cur_chip << GPMI_CTRL0_CS_OFFSET) | GPMI_CTRL0_ADDRESS_NAND_DATA; d->cmd.pio_words[1] = 0; d->cmd.pio_words[2] = GPMI_ECCCTRL_ENABLE_ECC | GPMI_ECCCTRL_ECC_CMD_ENCODE | GPMI_ECCCTRL_BUFFER_MASK_BCH_PAGE; d->cmd.pio_words[3] = (mtd->writesize + mtd->oobsize); d->cmd.pio_words[4] = (dma_addr_t)nand_info->data_buf; d->cmd.pio_words[5] = (dma_addr_t)nand_info->oob_buf; if (nand_info->en_randomizer) { d->cmd.pio_words[2] |= GPMI_ECCCTRL_RANDOMIZER_ENABLE | GPMI_ECCCTRL_RANDOMIZER_TYPE2; /* * Write NAND page number needed to be randomized * to GPMI_ECCCOUNT register. * * The value is between 0-255. For additional details * check 9.6.6.4 of i.MX7D Applications Processor reference */ d->cmd.pio_words[3] |= (page % 256) << 16; } mxs_dma_desc_append(channel, d); /* Flush caches */ mxs_nand_flush_data_buf(nand_info); /* Execute the DMA chain. */ ret = mxs_dma_go(channel); if (ret) { printf("MXS NAND: DMA write error\n"); goto rtn; } ret = mxs_nand_wait_for_bch_complete(nand_info); if (ret) { printf("MXS NAND: BCH write timeout\n"); goto rtn; } rtn: mxs_nand_return_dma_descs(nand_info); return 0; } /* * Read OOB from NAND. * * This function is a veneer that replaces the function originally installed by * the NAND Flash MTD code. */ static int mxs_nand_hook_read_oob(struct mtd_info *mtd, loff_t from, struct mtd_oob_ops *ops) { struct nand_chip *chip = mtd_to_nand(mtd); struct mxs_nand_info *nand_info = nand_get_controller_data(chip); int ret; if (ops->mode == MTD_OPS_RAW) nand_info->raw_oob_mode = 1; else nand_info->raw_oob_mode = 0; ret = nand_info->hooked_read_oob(mtd, from, ops); nand_info->raw_oob_mode = 0; return ret; } /* * Write OOB to NAND. * * This function is a veneer that replaces the function originally installed by * the NAND Flash MTD code. */ static int mxs_nand_hook_write_oob(struct mtd_info *mtd, loff_t to, struct mtd_oob_ops *ops) { struct nand_chip *chip = mtd_to_nand(mtd); struct mxs_nand_info *nand_info = nand_get_controller_data(chip); int ret; if (ops->mode == MTD_OPS_RAW) nand_info->raw_oob_mode = 1; else nand_info->raw_oob_mode = 0; ret = nand_info->hooked_write_oob(mtd, to, ops); nand_info->raw_oob_mode = 0; return ret; } /* * Mark a block bad in NAND. * * This function is a veneer that replaces the function originally installed by * the NAND Flash MTD code. */ static int mxs_nand_hook_block_markbad(struct mtd_info *mtd, loff_t ofs) { struct nand_chip *chip = mtd_to_nand(mtd); struct mxs_nand_info *nand_info = nand_get_controller_data(chip); int ret; nand_info->marking_block_bad = 1; ret = nand_info->hooked_block_markbad(mtd, ofs); nand_info->marking_block_bad = 0; return ret; } /* * There are several places in this driver where we have to handle the OOB and * block marks. This is the function where things are the most complicated, so * this is where we try to explain it all. All the other places refer back to * here. * * These are the rules, in order of decreasing importance: * * 1) Nothing the caller does can be allowed to imperil the block mark, so all * write operations take measures to protect it. * * 2) In read operations, the first byte of the OOB we return must reflect the * true state of the block mark, no matter where that block mark appears in * the physical page. * * 3) ECC-based read operations return an OOB full of set bits (since we never * allow ECC-based writes to the OOB, it doesn't matter what ECC-based reads * return). * * 4) "Raw" read operations return a direct view of the physical bytes in the * page, using the conventional definition of which bytes are data and which * are OOB. This gives the caller a way to see the actual, physical bytes * in the page, without the distortions applied by our ECC engine. * * What we do for this specific read operation depends on whether we're doing * "raw" read, or an ECC-based read. * * It turns out that knowing whether we want an "ECC-based" or "raw" read is not * easy. When reading a page, for example, the NAND Flash MTD code calls our * ecc.read_page or ecc.read_page_raw function. Thus, the fact that MTD wants an * ECC-based or raw view of the page is implicit in which function it calls * (there is a similar pair of ECC-based/raw functions for writing). * * Since MTD assumes the OOB is not covered by ECC, there is no pair of * ECC-based/raw functions for reading or or writing the OOB. The fact that the * caller wants an ECC-based or raw view of the page is not propagated down to * this driver. * * Since our OOB *is* covered by ECC, we need this information. So, we hook the * ecc.read_oob and ecc.write_oob function pointers in the owning * struct mtd_info with our own functions. These hook functions set the * raw_oob_mode field so that, when control finally arrives here, we'll know * what to do. */ static int mxs_nand_ecc_read_oob(struct mtd_info *mtd, struct nand_chip *nand, int page) { struct mxs_nand_info *nand_info = nand_get_controller_data(nand); /* * First, fill in the OOB buffer. If we're doing a raw read, we need to * get the bytes from the physical page. If we're not doing a raw read, * we need to fill the buffer with set bits. */ if (nand_info->raw_oob_mode) { /* * If control arrives here, we're doing a "raw" read. Send the * command to read the conventional OOB and read it. */ nand->cmdfunc(mtd, NAND_CMD_READ0, mtd->writesize, page); nand->read_buf(mtd, nand->oob_poi, mtd->oobsize); } else { /* * If control arrives here, we're not doing a "raw" read. Fill * the OOB buffer with set bits and correct the block mark. */ memset(nand->oob_poi, 0xff, mtd->oobsize); nand->cmdfunc(mtd, NAND_CMD_READ0, mtd->writesize, page); mxs_nand_read_buf(mtd, nand->oob_poi, 1); } return 0; } /* * Write OOB data to NAND. */ static int mxs_nand_ecc_write_oob(struct mtd_info *mtd, struct nand_chip *nand, int page) { struct mxs_nand_info *nand_info = nand_get_controller_data(nand); uint8_t block_mark = 0; /* * There are fundamental incompatibilities between the i.MX GPMI NFC and * the NAND Flash MTD model that make it essentially impossible to write * the out-of-band bytes. * * We permit *ONE* exception. If the *intent* of writing the OOB is to * mark a block bad, we can do that. */ if (!nand_info->marking_block_bad) { printf("NXS NAND: Writing OOB isn't supported\n"); return -EIO; } /* Write the block mark. */ nand->cmdfunc(mtd, NAND_CMD_SEQIN, mtd->writesize, page); nand->write_buf(mtd, &block_mark, 1); nand->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1); /* Check if it worked. */ if (nand->waitfunc(mtd, nand) & NAND_STATUS_FAIL) return -EIO; return 0; } /* * Claims all blocks are good. * * In principle, this function is *only* called when the NAND Flash MTD system * isn't allowed to keep an in-memory bad block table, so it is forced to ask * the driver for bad block information. * * In fact, we permit the NAND Flash MTD system to have an in-memory BBT, so * this function is *only* called when we take it away. * * Thus, this function is only called when we want *all* blocks to look good, * so it *always* return success. */ static int mxs_nand_block_bad(struct mtd_info *mtd, loff_t ofs) { return 0; } static int mxs_nand_set_geometry(struct mtd_info *mtd, struct bch_geometry *geo) { struct nand_chip *chip = mtd_to_nand(mtd); struct nand_chip *nand = mtd_to_nand(mtd); struct mxs_nand_info *nand_info = nand_get_controller_data(nand); if (chip->ecc_strength_ds > nand_info->max_ecc_strength_supported) { printf("unsupported NAND chip, minimum ecc required %d\n" , chip->ecc_strength_ds); return -EINVAL; } if ((!(chip->ecc_strength_ds > 0 && chip->ecc_step_ds > 0) && mtd->oobsize < 1024) || nand_info->legacy_bch_geometry) { dev_warn(this->dev, "use legacy bch geometry\n"); return mxs_nand_legacy_calc_ecc_layout(geo, mtd); } if (mtd->oobsize > 1024 || chip->ecc_step_ds < mtd->oobsize) return mxs_nand_calc_ecc_for_large_oob(geo, mtd); return mxs_nand_calc_ecc_layout_by_info(geo, mtd, chip->ecc_strength_ds, chip->ecc_step_ds); return 0; } /* * At this point, the physical NAND Flash chips have been identified and * counted, so we know the physical geometry. This enables us to make some * important configuration decisions. * * The return value of this function propagates directly back to this driver's * board_nand_init(). Anything other than zero will cause this driver to * tear everything down and declare failure. */ int mxs_nand_setup_ecc(struct mtd_info *mtd) { struct nand_chip *nand = mtd_to_nand(mtd); struct mxs_nand_info *nand_info = nand_get_controller_data(nand); struct bch_geometry *geo = &nand_info->bch_geometry; struct mxs_bch_regs *bch_regs = nand_info->bch_regs; uint32_t tmp; int ret; nand_info->en_randomizer = 0; nand_info->oobsize = mtd->oobsize; nand_info->writesize = mtd->writesize; ret = mxs_nand_set_geometry(mtd, geo); if (ret) return ret; /* Configure BCH and set NFC geometry */ mxs_reset_block(&bch_regs->hw_bch_ctrl_reg); /* Configure layout 0 */ tmp = (geo->ecc_chunk_count - 1) << BCH_FLASHLAYOUT0_NBLOCKS_OFFSET; tmp |= MXS_NAND_METADATA_SIZE << BCH_FLASHLAYOUT0_META_SIZE_OFFSET; tmp |= (geo->ecc_strength >> 1) << BCH_FLASHLAYOUT0_ECC0_OFFSET; tmp |= geo->ecc_chunk0_size >> MXS_NAND_CHUNK_DATA_CHUNK_SIZE_SHIFT; tmp |= (geo->gf_len == 14 ? 1 : 0) << BCH_FLASHLAYOUT0_GF13_0_GF14_1_OFFSET; writel(tmp, &bch_regs->hw_bch_flash0layout0); nand_info->bch_flash0layout0 = tmp; tmp = (mtd->writesize + mtd->oobsize) << BCH_FLASHLAYOUT1_PAGE_SIZE_OFFSET; tmp |= (geo->ecc_strength >> 1) << BCH_FLASHLAYOUT1_ECCN_OFFSET; tmp |= geo->ecc_chunkn_size >> MXS_NAND_CHUNK_DATA_CHUNK_SIZE_SHIFT; tmp |= (geo->gf_len == 14 ? 1 : 0) << BCH_FLASHLAYOUT1_GF13_0_GF14_1_OFFSET; writel(tmp, &bch_regs->hw_bch_flash0layout1); nand_info->bch_flash0layout1 = tmp; /* Set erase threshold to ecc strength for mx6ul, mx6qp and mx7 */ if (is_mx6dqp() || is_mx7() || is_mx6ul() || is_imx8() || is_imx8m()) writel(BCH_MODE_ERASE_THRESHOLD(geo->ecc_strength), &bch_regs->hw_bch_mode); /* Set *all* chip selects to use layout 0 */ writel(0, &bch_regs->hw_bch_layoutselect); /* Enable BCH complete interrupt */ writel(BCH_CTRL_COMPLETE_IRQ_EN, &bch_regs->hw_bch_ctrl_set); /* Hook some operations at the MTD level. */ if (mtd->_read_oob != mxs_nand_hook_read_oob) { nand_info->hooked_read_oob = mtd->_read_oob; mtd->_read_oob = mxs_nand_hook_read_oob; } if (mtd->_write_oob != mxs_nand_hook_write_oob) { nand_info->hooked_write_oob = mtd->_write_oob; mtd->_write_oob = mxs_nand_hook_write_oob; } if (mtd->_block_markbad != mxs_nand_hook_block_markbad) { nand_info->hooked_block_markbad = mtd->_block_markbad; mtd->_block_markbad = mxs_nand_hook_block_markbad; } return 0; } /* * Allocate DMA buffers */ int mxs_nand_alloc_buffers(struct mxs_nand_info *nand_info) { uint8_t *buf; const int size = NAND_MAX_PAGESIZE + NAND_MAX_OOBSIZE; nand_info->data_buf_size = roundup(size, MXS_DMA_ALIGNMENT); /* DMA buffers */ buf = memalign(MXS_DMA_ALIGNMENT, nand_info->data_buf_size); if (!buf) { printf("MXS NAND: Error allocating DMA buffers\n"); return -ENOMEM; } memset(buf, 0, nand_info->data_buf_size); nand_info->data_buf = buf; nand_info->oob_buf = buf + NAND_MAX_PAGESIZE; /* Command buffers */ nand_info->cmd_buf = memalign(MXS_DMA_ALIGNMENT, MXS_NAND_COMMAND_BUFFER_SIZE); if (!nand_info->cmd_buf) { free(buf); printf("MXS NAND: Error allocating command buffers\n"); return -ENOMEM; } memset(nand_info->cmd_buf, 0, MXS_NAND_COMMAND_BUFFER_SIZE); nand_info->cmd_queue_len = 0; return 0; } /* * Initializes the NFC hardware. */ static int mxs_nand_init_dma(struct mxs_nand_info *info) { int i = 0, j, ret = 0; info->desc = malloc(sizeof(struct mxs_dma_desc *) * MXS_NAND_DMA_DESCRIPTOR_COUNT); if (!info->desc) { ret = -ENOMEM; goto err1; } /* Allocate the DMA descriptors. */ for (i = 0; i < MXS_NAND_DMA_DESCRIPTOR_COUNT; i++) { info->desc[i] = mxs_dma_desc_alloc(); if (!info->desc[i]) { ret = -ENOMEM; goto err2; } } /* Init the DMA controller. */ mxs_dma_init(); for (j = MXS_DMA_CHANNEL_AHB_APBH_GPMI0; j <= MXS_DMA_CHANNEL_AHB_APBH_GPMI7; j++) { ret = mxs_dma_init_channel(j); if (ret) goto err3; } /* Reset the GPMI block. */ mxs_reset_block(&info->gpmi_regs->hw_gpmi_ctrl0_reg); mxs_reset_block(&info->bch_regs->hw_bch_ctrl_reg); /* * Choose NAND mode, set IRQ polarity, disable write protection and * select BCH ECC. */ clrsetbits_le32(&info->gpmi_regs->hw_gpmi_ctrl1, GPMI_CTRL1_GPMI_MODE, GPMI_CTRL1_ATA_IRQRDY_POLARITY | GPMI_CTRL1_DEV_RESET | GPMI_CTRL1_BCH_MODE); return 0; err3: for (--j; j >= MXS_DMA_CHANNEL_AHB_APBH_GPMI0; j--) mxs_dma_release(j); err2: for (--i; i >= 0; i--) mxs_dma_desc_free(info->desc[i]); free(info->desc); err1: if (ret == -ENOMEM) printf("MXS NAND: Unable to allocate DMA descriptors\n"); return ret; } int mxs_nand_init_spl(struct nand_chip *nand) { struct mxs_nand_info *nand_info; int err; nand_info = malloc(sizeof(struct mxs_nand_info)); if (!nand_info) { printf("MXS NAND: Failed to allocate private data\n"); return -ENOMEM; } memset(nand_info, 0, sizeof(struct mxs_nand_info)); nand_info->gpmi_regs = (struct mxs_gpmi_regs *)MXS_GPMI_BASE; nand_info->bch_regs = (struct mxs_bch_regs *)MXS_BCH_BASE; if (is_mx6sx() || is_mx7() || is_imx8() || is_imx8m()) nand_info->max_ecc_strength_supported = 62; else nand_info->max_ecc_strength_supported = 40; err = mxs_nand_alloc_buffers(nand_info); if (err) return err; err = mxs_nand_init_dma(nand_info); if (err) return err; nand_set_controller_data(nand, nand_info); nand->options |= NAND_NO_SUBPAGE_WRITE; nand->cmd_ctrl = mxs_nand_cmd_ctrl; nand->dev_ready = mxs_nand_device_ready; nand->select_chip = mxs_nand_select_chip; nand->read_byte = mxs_nand_read_byte; nand->read_buf = mxs_nand_read_buf; nand->ecc.read_page = mxs_nand_ecc_read_page; nand->ecc.mode = NAND_ECC_HW; return 0; } int mxs_nand_init_ctrl(struct mxs_nand_info *nand_info) { struct mtd_info *mtd; struct nand_chip *nand; int err; nand = &nand_info->chip; mtd = nand_to_mtd(nand); err = mxs_nand_alloc_buffers(nand_info); if (err) return err; err = mxs_nand_init_dma(nand_info); if (err) goto err_free_buffers; memset(&fake_ecc_layout, 0, sizeof(fake_ecc_layout)); #ifdef CONFIG_SYS_NAND_USE_FLASH_BBT nand->bbt_options |= NAND_BBT_USE_FLASH | NAND_BBT_NO_OOB; #endif nand_set_controller_data(nand, nand_info); nand->options |= NAND_NO_SUBPAGE_WRITE; if (nand_info->dev) nand->flash_node = dev_of_offset(nand_info->dev); nand->cmd_ctrl = mxs_nand_cmd_ctrl; nand->dev_ready = mxs_nand_device_ready; nand->select_chip = mxs_nand_select_chip; nand->block_bad = mxs_nand_block_bad; nand->read_byte = mxs_nand_read_byte; nand->read_buf = mxs_nand_read_buf; nand->write_buf = mxs_nand_write_buf; /* first scan to find the device and get the page size */ if (nand_scan_ident(mtd, CONFIG_SYS_MAX_NAND_DEVICE, NULL)) goto err_free_buffers; if (mxs_nand_setup_ecc(mtd)) goto err_free_buffers; nand->ecc.read_page = mxs_nand_ecc_read_page; nand->ecc.write_page = mxs_nand_ecc_write_page; nand->ecc.read_oob = mxs_nand_ecc_read_oob; nand->ecc.write_oob = mxs_nand_ecc_write_oob; nand->ecc.layout = &fake_ecc_layout; nand->ecc.mode = NAND_ECC_HW; nand->ecc.size = nand_info->bch_geometry.ecc_chunkn_size; nand->ecc.strength = nand_info->bch_geometry.ecc_strength; /* second phase scan */ err = nand_scan_tail(mtd); if (err) goto err_free_buffers; err = nand_register(0, mtd); if (err) goto err_free_buffers; return 0; err_free_buffers: free(nand_info->data_buf); free(nand_info->cmd_buf); return err; } #ifndef CONFIG_NAND_MXS_DT void board_nand_init(void) { struct mxs_nand_info *nand_info; nand_info = malloc(sizeof(struct mxs_nand_info)); if (!nand_info) { printf("MXS NAND: Failed to allocate private data\n"); return; } memset(nand_info, 0, sizeof(struct mxs_nand_info)); nand_info->gpmi_regs = (struct mxs_gpmi_regs *)MXS_GPMI_BASE; nand_info->bch_regs = (struct mxs_bch_regs *)MXS_BCH_BASE; /* Refer to Chapter 17 for i.MX6DQ, Chapter 18 for i.MX6SX */ if (is_mx6sx() || is_mx7()) nand_info->max_ecc_strength_supported = 62; else nand_info->max_ecc_strength_supported = 40; #ifdef CONFIG_NAND_MXS_USE_MINIMUM_ECC nand_info->use_minimum_ecc = true; #endif if (mxs_nand_init_ctrl(nand_info) < 0) goto err; return; err: free(nand_info); } #endif /* * Read NAND layout for FCB block generation. */ void mxs_nand_get_layout(struct mtd_info *mtd, struct mxs_nand_layout *l) { struct mxs_bch_regs *bch_regs = (struct mxs_bch_regs *)MXS_BCH_BASE; u32 tmp; tmp = readl(&bch_regs->hw_bch_flash0layout0); l->nblocks = (tmp & BCH_FLASHLAYOUT0_NBLOCKS_MASK) >> BCH_FLASHLAYOUT0_NBLOCKS_OFFSET; l->meta_size = (tmp & BCH_FLASHLAYOUT0_META_SIZE_MASK) >> BCH_FLASHLAYOUT0_META_SIZE_OFFSET; tmp = readl(&bch_regs->hw_bch_flash0layout1); l->data0_size = 4 * ((tmp & BCH_FLASHLAYOUT0_DATA0_SIZE_MASK) >> BCH_FLASHLAYOUT0_DATA0_SIZE_OFFSET); l->ecc0 = (tmp & BCH_FLASHLAYOUT0_ECC0_MASK) >> BCH_FLASHLAYOUT0_ECC0_OFFSET; l->datan_size = 4 * ((tmp & BCH_FLASHLAYOUT1_DATAN_SIZE_MASK) >> BCH_FLASHLAYOUT1_DATAN_SIZE_OFFSET); l->eccn = (tmp & BCH_FLASHLAYOUT1_ECCN_MASK) >> BCH_FLASHLAYOUT1_ECCN_OFFSET; l->gf_len = (tmp & BCH_FLASHLAYOUT1_GF13_0_GF14_1_MASK) >> BCH_FLASHLAYOUT1_GF13_0_GF14_1_OFFSET; } /* * Set BCH to specific layout used by ROM bootloader to read FCB. */ void mxs_nand_mode_fcb_62bit(struct mtd_info *mtd) { u32 tmp; struct mxs_bch_regs *bch_regs = (struct mxs_bch_regs *)MXS_BCH_BASE; struct nand_chip *nand = mtd_to_nand(mtd); struct mxs_nand_info *nand_info = nand_get_controller_data(nand); nand_info->en_randomizer = 1; mtd->writesize = 1024; mtd->oobsize = 1862 - 1024; /* 8 ecc_chunks_*/ tmp = 7 << BCH_FLASHLAYOUT0_NBLOCKS_OFFSET; /* 32 bytes for metadata */ tmp |= 32 << BCH_FLASHLAYOUT0_META_SIZE_OFFSET; /* using ECC62 level to be performed */ tmp |= 0x1F << BCH_FLASHLAYOUT0_ECC0_OFFSET; /* 0x20 * 4 bytes of the data0 block */ tmp |= 0x20 << BCH_FLASHLAYOUT0_DATA0_SIZE_OFFSET; tmp |= 0 << BCH_FLASHLAYOUT0_GF13_0_GF14_1_OFFSET; writel(tmp, &bch_regs->hw_bch_flash0layout0); /* 1024 for data + 838 for OOB */ tmp = 1862 << BCH_FLASHLAYOUT1_PAGE_SIZE_OFFSET; /* using ECC62 level to be performed */ tmp |= 0x1F << BCH_FLASHLAYOUT1_ECCN_OFFSET; /* 0x20 * 4 bytes of the data0 block */ tmp |= 0x20 << BCH_FLASHLAYOUT1_DATAN_SIZE_OFFSET; tmp |= 0 << BCH_FLASHLAYOUT1_GF13_0_GF14_1_OFFSET; writel(tmp, &bch_regs->hw_bch_flash0layout1); } /* * Set BCH to specific layout used by ROM bootloader to read FCB. */ void mxs_nand_mode_fcb_40bit(struct mtd_info *mtd) { u32 tmp; struct mxs_bch_regs *bch_regs = (struct mxs_bch_regs *)MXS_BCH_BASE; struct nand_chip *nand = mtd_to_nand(mtd); struct mxs_nand_info *nand_info = nand_get_controller_data(nand); /* no randomizer in this setting*/ nand_info->en_randomizer = 0; mtd->writesize = 1024; mtd->oobsize = 1576 - 1024; /* 8 ecc_chunks_*/ tmp = 7 << BCH_FLASHLAYOUT0_NBLOCKS_OFFSET; /* 32 bytes for metadata */ tmp |= 32 << BCH_FLASHLAYOUT0_META_SIZE_OFFSET; /* using ECC40 level to be performed */ tmp |= 0x14 << BCH_FLASHLAYOUT0_ECC0_OFFSET; /* 0x20 * 4 bytes of the data0 block */ tmp |= 0x20 << BCH_FLASHLAYOUT0_DATA0_SIZE_OFFSET; tmp |= 0 << BCH_FLASHLAYOUT0_GF13_0_GF14_1_OFFSET; writel(tmp, &bch_regs->hw_bch_flash0layout0); /* 1024 for data + 552 for OOB */ tmp = 1576 << BCH_FLASHLAYOUT1_PAGE_SIZE_OFFSET; /* using ECC40 level to be performed */ tmp |= 0x14 << BCH_FLASHLAYOUT1_ECCN_OFFSET; /* 0x20 * 4 bytes of the data0 block */ tmp |= 0x20 << BCH_FLASHLAYOUT1_DATAN_SIZE_OFFSET; tmp |= 0 << BCH_FLASHLAYOUT1_GF13_0_GF14_1_OFFSET; writel(tmp, &bch_regs->hw_bch_flash0layout1); } /* * Restore BCH to normal settings. */ void mxs_nand_mode_normal(struct mtd_info *mtd) { struct mxs_bch_regs *bch_regs = (struct mxs_bch_regs *)MXS_BCH_BASE; struct nand_chip *nand = mtd_to_nand(mtd); struct mxs_nand_info *nand_info = nand_get_controller_data(nand); nand_info->en_randomizer = 0; mtd->writesize = nand_info->writesize; mtd->oobsize = nand_info->oobsize; writel(nand_info->bch_flash0layout0, &bch_regs->hw_bch_flash0layout0); writel(nand_info->bch_flash0layout1, &bch_regs->hw_bch_flash0layout1); } uint32_t mxs_nand_mark_byte_offset(struct mtd_info *mtd) { struct nand_chip *chip = mtd_to_nand(mtd); struct mxs_nand_info *nand_info = nand_get_controller_data(chip); struct bch_geometry *geo = &nand_info->bch_geometry; return geo->block_mark_byte_offset; } uint32_t mxs_nand_mark_bit_offset(struct mtd_info *mtd) { struct nand_chip *chip = mtd_to_nand(mtd); struct mxs_nand_info *nand_info = nand_get_controller_data(chip); struct bch_geometry *geo = &nand_info->bch_geometry; return geo->block_mark_bit_offset; }