/* * (C) Copyright 2003 * Gerry Hamel, geh@ti.com, Texas Instruments * * Based on * linux/drivers/usb/device/bi/omap.c * TI OMAP1510 USB bus interface driver * * Author: MontaVista Software, Inc. * source@mvista.com * (C) Copyright 2002 * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation; either version 2 of the License, or * (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA * */ #include #if defined(CONFIG_OMAP1510) && defined(CONFIG_USB_DEVICE) #include #ifdef CONFIG_OMAP_SX1 #include #endif #include "usbdcore.h" #include "usbdcore_omap1510.h" #include "usbdcore_ep0.h" #define UDC_MAX_ENDPOINTS 31 /* Number of endpoints on this UDC */ /* Some kind of debugging output... */ #if 1 #define UDCDBG(str) #define UDCDBGA(fmt,args...) #else /* The bugs still exists... */ #define UDCDBG(str) serial_printf("[%s] %s:%d: " str "\n", __FILE__,__FUNCTION__,__LINE__) #define UDCDBGA(fmt,args...) serial_printf("[%s] %s:%d: " fmt "\n", __FILE__,__FUNCTION__,__LINE__, ##args) #endif #if 1 #define UDCREG(name) #define UDCREGL(name) #else /* The bugs still exists... */ #define UDCREG(name) serial_printf("%s():%d: %s[%08x]=%.4x\n",__FUNCTION__,__LINE__, (#name), name, inw(name)) /* For 16-bit regs */ #define UDCREGL(name) serial_printf("%s():%d: %s[%08x]=%.8x\n",__FUNCTION__,__LINE__, (#name), name, inl(name)) /* For 32-bit regs */ #endif static struct urb *ep0_urb = NULL; static struct usb_device_instance *udc_device; /* Used in interrupt handler */ static u16 udc_devstat = 0; /* UDC status (DEVSTAT) */ static u32 udc_interrupts = 0; static void udc_stall_ep (unsigned int ep_addr); static struct usb_endpoint_instance *omap1510_find_ep (int ep) { int i; for (i = 0; i < udc_device->bus->max_endpoints; i++) { if (udc_device->bus->endpoint_array[i].endpoint_address == ep) return &udc_device->bus->endpoint_array[i]; } return NULL; } /* ************************************************************************** */ /* IO */ /* * omap1510_prepare_endpoint_for_rx * * This function implements TRM Figure 14-11. * * The endpoint to prepare for transfer is specified as a physical endpoint * number. For OUT (rx) endpoints 1 through 15, the corresponding endpoint * configuration register is checked to see if the endpoint is ISO or not. * If the OUT endpoint is valid and is non-ISO then its FIFO is enabled. * No action is taken for endpoint 0 or for IN (tx) endpoints 16 through 30. */ static void omap1510_prepare_endpoint_for_rx (int ep_addr) { int ep_num = ep_addr & USB_ENDPOINT_NUMBER_MASK; UDCDBGA ("omap1510_prepare_endpoint %x", ep_addr); if (((ep_addr & USB_ENDPOINT_DIR_MASK) == USB_DIR_OUT)) { if ((inw (UDC_EP_RX (ep_num)) & (UDC_EPn_RX_Valid | UDC_EPn_RX_Iso)) == UDC_EPn_RX_Valid) { /* rx endpoint is valid, non-ISO, so enable its FIFO */ outw (UDC_EP_Sel | ep_num, UDC_EP_NUM); outw (UDC_Set_FIFO_En, UDC_CTRL); outw (0, UDC_EP_NUM); } } } /* omap1510_configure_endpoints * * This function implements TRM Figure 14-10. */ static void omap1510_configure_endpoints (struct usb_device_instance *device) { int ep; struct usb_bus_instance *bus; struct usb_endpoint_instance *endpoint; unsigned short ep_ptr; unsigned short ep_size; unsigned short ep_isoc; unsigned short ep_doublebuffer; int ep_addr; int packet_size; int buffer_size; int attributes; bus = device->bus; /* There is a dedicated 2048 byte buffer for USB packets that may be * arbitrarily partitioned among the endpoints on 8-byte boundaries. * The first 8 bytes are reserved for receiving setup packets on * endpoint 0. */ ep_ptr = 8; /* reserve the first 8 bytes for the setup fifo */ for (ep = 0; ep < bus->max_endpoints; ep++) { endpoint = bus->endpoint_array + ep; ep_addr = endpoint->endpoint_address; if ((ep_addr & USB_ENDPOINT_DIR_MASK) == USB_DIR_IN) { /* IN endpoint */ packet_size = endpoint->tx_packetSize; attributes = endpoint->tx_attributes; } else { /* OUT endpoint */ packet_size = endpoint->rcv_packetSize; attributes = endpoint->rcv_attributes; } switch (packet_size) { case 0: ep_size = 0; break; case 8: ep_size = 0; break; case 16: ep_size = 1; break; case 32: ep_size = 2; break; case 64: ep_size = 3; break; case 128: ep_size = 4; break; case 256: ep_size = 5; break; case 512: ep_size = 6; break; default: UDCDBGA ("ep 0x%02x has bad packet size %d", ep_addr, packet_size); packet_size = 0; ep_size = 0; break; } switch (attributes & USB_ENDPOINT_XFERTYPE_MASK) { case USB_ENDPOINT_XFER_CONTROL: case USB_ENDPOINT_XFER_BULK: case USB_ENDPOINT_XFER_INT: default: /* A non-isochronous endpoint may optionally be * double-buffered. For now we disable * double-buffering. */ ep_doublebuffer = 0; ep_isoc = 0; if (packet_size > 64) packet_size = 0; if (!ep || !ep_doublebuffer) buffer_size = packet_size; else buffer_size = packet_size * 2; break; case USB_ENDPOINT_XFER_ISOC: /* Isochronous endpoints are always double- * buffered, but the double-buffering bit * in the endpoint configuration register * becomes the msb of the endpoint size so we * set the double-buffering flag to zero. */ ep_doublebuffer = 0; ep_isoc = 1; buffer_size = packet_size * 2; break; } /* check to see if our packet buffer RAM is exhausted */ if ((ep_ptr + buffer_size) > 2048) { UDCDBGA ("out of packet RAM for ep 0x%02x buf size %d", ep_addr, buffer_size); buffer_size = packet_size = 0; } /* force a default configuration for endpoint 0 since it is * always enabled */ if (!ep && ((packet_size < 8) || (packet_size > 64))) { buffer_size = packet_size = 64; ep_size = 3; } if (!ep) { /* configure endpoint 0 */ outw ((ep_size << 12) | (ep_ptr >> 3), UDC_EP0); /*UDCDBGA("ep 0 buffer offset 0x%03x packet size 0x%03x", */ /* ep_ptr, packet_size); */ } else if ((ep_addr & USB_ENDPOINT_DIR_MASK) == USB_DIR_IN) { /* IN endpoint */ if (packet_size) { outw ((1 << 15) | (ep_doublebuffer << 14) | (ep_size << 12) | (ep_isoc << 11) | (ep_ptr >> 3), UDC_EP_TX (ep_addr & USB_ENDPOINT_NUMBER_MASK)); UDCDBGA ("IN ep %d buffer offset 0x%03x" " packet size 0x%03x", ep_addr & USB_ENDPOINT_NUMBER_MASK, ep_ptr, packet_size); } else { outw (0, UDC_EP_TX (ep_addr & USB_ENDPOINT_NUMBER_MASK)); } } else { /* OUT endpoint */ if (packet_size) { outw ((1 << 15) | (ep_doublebuffer << 14) | (ep_size << 12) | (ep_isoc << 11) | (ep_ptr >> 3), UDC_EP_RX (ep_addr & USB_ENDPOINT_NUMBER_MASK)); UDCDBGA ("OUT ep %d buffer offset 0x%03x" " packet size 0x%03x", ep_addr & USB_ENDPOINT_NUMBER_MASK, ep_ptr, packet_size); } else { outw (0, UDC_EP_RX (ep_addr & USB_ENDPOINT_NUMBER_MASK)); } } ep_ptr += buffer_size; } } /* omap1510_deconfigure_device * * This function balances omap1510_configure_device. */ static void omap1510_deconfigure_device (void) { int epnum; UDCDBG ("clear Cfg_Lock"); outw (inw (UDC_SYSCON1) & ~UDC_Cfg_Lock, UDC_SYSCON1); UDCREG (UDC_SYSCON1); /* deconfigure all endpoints */ for (epnum = 1; epnum <= 15; epnum++) { outw (0, UDC_EP_RX (epnum)); outw (0, UDC_EP_TX (epnum)); } } /* omap1510_configure_device * * This function implements TRM Figure 14-9. */ static void omap1510_configure_device (struct usb_device_instance *device) { omap1510_configure_endpoints (device); /* Figure 14-9 indicates we should enable interrupts here, but we have * other routines (udc_all_interrupts, udc_suspended_interrupts) to * do that. */ UDCDBG ("set Cfg_Lock"); outw (inw (UDC_SYSCON1) | UDC_Cfg_Lock, UDC_SYSCON1); UDCREG (UDC_SYSCON1); } /* omap1510_write_noniso_tx_fifo * * This function implements TRM Figure 14-30. * * If the endpoint has an active tx_urb, then the next packet of data from the * URB is written to the tx FIFO. The total amount of data in the urb is given * by urb->actual_length. The maximum amount of data that can be sent in any * one packet is given by endpoint->tx_packetSize. The number of data bytes * from this URB that have already been transmitted is given by endpoint->sent. * endpoint->last is updated by this routine with the number of data bytes * transmitted in this packet. * * In accordance with Figure 14-30, the EP_NUM register must already have been * written with the value to select the appropriate tx FIFO before this routine * is called. */ static void omap1510_write_noniso_tx_fifo (struct usb_endpoint_instance *endpoint) { struct urb *urb = endpoint->tx_urb; if (urb) { unsigned int last, i; UDCDBGA ("urb->buffer %p, buffer_length %d, actual_length %d", urb->buffer, urb->buffer_length, urb->actual_length); if ((last = MIN (urb->actual_length - endpoint->sent, endpoint->tx_packetSize))) { u8 *cp = urb->buffer + endpoint->sent; UDCDBGA ("endpoint->sent %d, tx_packetSize %d, last %d", endpoint->sent, endpoint->tx_packetSize, last); if (((u32) cp & 1) == 0) { /* word aligned? */ outsw (UDC_DATA, cp, last >> 1); } else { /* byte aligned. */ for (i = 0; i < (last >> 1); i++) { u16 w = ((u16) cp[2 * i + 1] << 8) | (u16) cp[2 * i]; outw (w, UDC_DATA); } } if (last & 1) { outb (*(cp + last - 1), UDC_DATA); } } endpoint->last = last; } } /* omap1510_read_noniso_rx_fifo * * This function implements TRM Figure 14-28. * * If the endpoint has an active rcv_urb, then the next packet of data is read * from the rcv FIFO and written to rcv_urb->buffer at offset * rcv_urb->actual_length to append the packet data to the data from any * previous packets for this transfer. We assume that there is sufficient room * left in the buffer to hold an entire packet of data. * * The return value is the number of bytes read from the FIFO for this packet. * * In accordance with Figure 14-28, the EP_NUM register must already have been * written with the value to select the appropriate rcv FIFO before this routine * is called. */ static int omap1510_read_noniso_rx_fifo (struct usb_endpoint_instance *endpoint) { struct urb *urb = endpoint->rcv_urb; int len = 0; if (urb) { len = inw (UDC_RXFSTAT); if (len) { unsigned char *cp = urb->buffer + urb->actual_length; insw (UDC_DATA, cp, len >> 1); if (len & 1) *(cp + len - 1) = inb (UDC_DATA); } } return len; } /* omap1510_prepare_for_control_write_status * * This function implements TRM Figure 14-17. * * We have to deal here with non-autodecoded control writes that haven't already * been dealt with by ep0_recv_setup. The non-autodecoded standard control * write requests are: set/clear endpoint feature, set configuration, set * interface, and set descriptor. ep0_recv_setup handles set/clear requests for * ENDPOINT_HALT by halting the endpoint for a set request and resetting the * endpoint for a clear request. ep0_recv_setup returns an error for * SET_DESCRIPTOR requests which causes them to be terminated with a stall by * the setup handler. A SET_INTERFACE request is handled by ep0_recv_setup by * generating a DEVICE_SET_INTERFACE event. This leaves only the * SET_CONFIGURATION event for us to deal with here. * */ static void omap1510_prepare_for_control_write_status (struct urb *urb) { struct usb_device_request *request = &urb->device_request;; /* check for a SET_CONFIGURATION request */ if (request->bRequest == USB_REQ_SET_CONFIGURATION) { int configuration = le16_to_cpu (request->wValue) & 0xff; unsigned short devstat = inw (UDC_DEVSTAT); if ((devstat & (UDC_ADD | UDC_CFG)) == UDC_ADD) { /* device is currently in ADDRESSED state */ if (configuration) { /* Assume the specified non-zero configuration * value is valid and switch to the CONFIGURED * state. */ outw (UDC_Dev_Cfg, UDC_SYSCON2); } } else if ((devstat & UDC_CFG) == UDC_CFG) { /* device is currently in CONFIGURED state */ if (!configuration) { /* Switch to ADDRESSED state. */ outw (UDC_Clr_Cfg, UDC_SYSCON2); } } } /* select EP0 tx FIFO */ outw (UDC_EP_Dir | UDC_EP_Sel, UDC_EP_NUM); /* clear endpoint (no data bytes in status stage) */ outw (UDC_Clr_EP, UDC_CTRL); /* enable the EP0 tx FIFO */ outw (UDC_Set_FIFO_En, UDC_CTRL); /* deselect the endpoint */ outw (UDC_EP_Dir, UDC_EP_NUM); } /* udc_state_transition_up * udc_state_transition_down * * Helper functions to implement device state changes. The device states and * the events that transition between them are: * * STATE_ATTACHED * || /\ * \/ || * DEVICE_HUB_CONFIGURED DEVICE_HUB_RESET * || /\ * \/ || * STATE_POWERED * || /\ * \/ || * DEVICE_RESET DEVICE_POWER_INTERRUPTION * || /\ * \/ || * STATE_DEFAULT * || /\ * \/ || * DEVICE_ADDRESS_ASSIGNED DEVICE_RESET * || /\ * \/ || * STATE_ADDRESSED * || /\ * \/ || * DEVICE_CONFIGURED DEVICE_DE_CONFIGURED * || /\ * \/ || * STATE_CONFIGURED * * udc_state_transition_up transitions up (in the direction from STATE_ATTACHED * to STATE_CONFIGURED) from the specified initial state to the specified final * state, passing through each intermediate state on the way. If the initial * state is at or above (i.e. nearer to STATE_CONFIGURED) the final state, then * no state transitions will take place. * * udc_state_transition_down transitions down (in the direction from * STATE_CONFIGURED to STATE_ATTACHED) from the specified initial state to the * specified final state, passing through each intermediate state on the way. * If the initial state is at or below (i.e. nearer to STATE_ATTACHED) the final * state, then no state transitions will take place. * * These functions must only be called with interrupts disabled. */ static void udc_state_transition_up (usb_device_state_t initial, usb_device_state_t final) { if (initial < final) { switch (initial) { case STATE_ATTACHED: usbd_device_event_irq (udc_device, DEVICE_HUB_CONFIGURED, 0); if (final == STATE_POWERED) break; case STATE_POWERED: usbd_device_event_irq (udc_device, DEVICE_RESET, 0); if (final == STATE_DEFAULT) break; case STATE_DEFAULT: usbd_device_event_irq (udc_device, DEVICE_ADDRESS_ASSIGNED, 0); if (final == STATE_ADDRESSED) break; case STATE_ADDRESSED: usbd_device_event_irq (udc_device, DEVICE_CONFIGURED, 0); case STATE_CONFIGURED: break; default: break; } } } static void udc_state_transition_down (usb_device_state_t initial, usb_device_state_t final) { if (initial > final) { switch (initial) { case STATE_CONFIGURED: usbd_device_event_irq (udc_device, DEVICE_DE_CONFIGURED, 0); if (final == STATE_ADDRESSED) break; case STATE_ADDRESSED: usbd_device_event_irq (udc_device, DEVICE_RESET, 0); if (final == STATE_DEFAULT) break; case STATE_DEFAULT: usbd_device_event_irq (udc_device, DEVICE_POWER_INTERRUPTION, 0); if (final == STATE_POWERED) break; case STATE_POWERED: usbd_device_event_irq (udc_device, DEVICE_HUB_RESET, 0); case STATE_ATTACHED: break; default: break; } } } /* Handle all device state changes. * This function implements TRM Figure 14-21. */ static void omap1510_udc_state_changed (void) { u16 bits; u16 devstat = inw (UDC_DEVSTAT); UDCDBGA ("state changed, devstat %x, old %x", devstat, udc_devstat); bits = devstat ^ udc_devstat; if (bits) { if (bits & UDC_ATT) { if (devstat & UDC_ATT) { UDCDBG ("device attached and powered"); udc_state_transition_up (udc_device->device_state, STATE_POWERED); } else { UDCDBG ("device detached or unpowered"); udc_state_transition_down (udc_device->device_state, STATE_ATTACHED); } } if (bits & UDC_USB_Reset) { if (devstat & UDC_USB_Reset) { UDCDBG ("device reset in progess"); udc_state_transition_down (udc_device->device_state, STATE_POWERED); } else { UDCDBG ("device reset completed"); } } if (bits & UDC_DEF) { if (devstat & UDC_DEF) { UDCDBG ("device entering default state"); udc_state_transition_up (udc_device->device_state, STATE_DEFAULT); } else { UDCDBG ("device leaving default state"); udc_state_transition_down (udc_device->device_state, STATE_POWERED); } } if (bits & UDC_SUS) { if (devstat & UDC_SUS) { UDCDBG ("entering suspended state"); usbd_device_event_irq (udc_device, DEVICE_BUS_INACTIVE, 0); } else { UDCDBG ("leaving suspended state"); usbd_device_event_irq (udc_device, DEVICE_BUS_ACTIVITY, 0); } } if (bits & UDC_R_WK_OK) { UDCDBGA ("remote wakeup %s", (devstat & UDC_R_WK_OK) ? "enabled" : "disabled"); } if (bits & UDC_ADD) { if (devstat & UDC_ADD) { UDCDBG ("default -> addressed"); udc_state_transition_up (udc_device->device_state, STATE_ADDRESSED); } else { UDCDBG ("addressed -> default"); udc_state_transition_down (udc_device->device_state, STATE_DEFAULT); } } if (bits & UDC_CFG) { if (devstat & UDC_CFG) { UDCDBG ("device configured"); /* The ep0_recv_setup function generates the * DEVICE_CONFIGURED event when a * USB_REQ_SET_CONFIGURATION setup packet is * received, so we should already be in the * state STATE_CONFIGURED. */ udc_state_transition_up (udc_device->device_state, STATE_CONFIGURED); } else { UDCDBG ("device deconfigured"); udc_state_transition_down (udc_device->device_state, STATE_ADDRESSED); } } } /* Clear interrupt source */ outw (UDC_DS_Chg, UDC_IRQ_SRC); /* Save current DEVSTAT */ udc_devstat = devstat; } /* Handle SETUP USB interrupt. * This function implements TRM Figure 14-14. */ static void omap1510_udc_setup (struct usb_endpoint_instance *endpoint) { UDCDBG ("-> Entering device setup"); do { const int setup_pktsize = 8; unsigned char *datap = (unsigned char *) &ep0_urb->device_request; /* Gain access to EP 0 setup FIFO */ outw (UDC_Setup_Sel, UDC_EP_NUM); /* Read control request data */ insb (UDC_DATA, datap, setup_pktsize); UDCDBGA ("EP0 setup read [%x %x %x %x %x %x %x %x]", *(datap + 0), *(datap + 1), *(datap + 2), *(datap + 3), *(datap + 4), *(datap + 5), *(datap + 6), *(datap + 7)); /* Reset EP0 setup FIFO */ outw (0, UDC_EP_NUM); } while (inw (UDC_IRQ_SRC) & UDC_Setup); /* Try to process setup packet */ if (ep0_recv_setup (ep0_urb)) { /* Not a setup packet, stall next EP0 transaction */ udc_stall_ep (0); UDCDBG ("can't parse setup packet, still waiting for setup"); return; } /* Check direction */ if ((ep0_urb->device_request.bmRequestType & USB_REQ_DIRECTION_MASK) == USB_REQ_HOST2DEVICE) { UDCDBG ("control write on EP0"); if (le16_to_cpu (ep0_urb->device_request.wLength)) { /* We don't support control write data stages. * The only standard control write request with a data * stage is SET_DESCRIPTOR, and ep0_recv_setup doesn't * support that so we just stall those requests. A * function driver might support a non-standard * write request with a data stage, but it isn't * obvious what we would do with the data if we read it * so we'll just stall it. It seems like the API isn't * quite right here. */ #if 0 /* Here is what we would do if we did support control * write data stages. */ ep0_urb->actual_length = 0; outw (0, UDC_EP_NUM); /* enable the EP0 rx FIFO */ outw (UDC_Set_FIFO_En, UDC_CTRL); #else /* Stall this request */ UDCDBG ("Stalling unsupported EP0 control write data " "stage."); udc_stall_ep (0); #endif } else { omap1510_prepare_for_control_write_status (ep0_urb); } } else { UDCDBG ("control read on EP0"); /* The ep0_recv_setup function has already placed our response * packet data in ep0_urb->buffer and the packet length in * ep0_urb->actual_length. */ endpoint->tx_urb = ep0_urb; endpoint->sent = 0; /* select the EP0 tx FIFO */ outw (UDC_EP_Dir | UDC_EP_Sel, UDC_EP_NUM); /* Write packet data to the FIFO. omap1510_write_noniso_tx_fifo * will update endpoint->last with the number of bytes written * to the FIFO. */ omap1510_write_noniso_tx_fifo (endpoint); /* enable the FIFO to start the packet transmission */ outw (UDC_Set_FIFO_En, UDC_CTRL); /* deselect the EP0 tx FIFO */ outw (UDC_EP_Dir, UDC_EP_NUM); } UDCDBG ("<- Leaving device setup"); } /* Handle endpoint 0 RX interrupt * This routine implements TRM Figure 14-16. */ static void omap1510_udc_ep0_rx (struct usb_endpoint_instance *endpoint) { unsigned short status; UDCDBG ("RX on EP0"); /* select EP0 rx FIFO */ outw (UDC_EP_Sel, UDC_EP_NUM); status = inw (UDC_STAT_FLG); if (status & UDC_ACK) { /* Check direction */ if ((ep0_urb->device_request.bmRequestType & USB_REQ_DIRECTION_MASK) == USB_REQ_HOST2DEVICE) { /* This rx interrupt must be for a control write data * stage packet. * * We don't support control write data stages. * We should never end up here. */ /* clear the EP0 rx FIFO */ outw (UDC_Clr_EP, UDC_CTRL); /* deselect the EP0 rx FIFO */ outw (0, UDC_EP_NUM); UDCDBG ("Stalling unexpected EP0 control write " "data stage packet"); udc_stall_ep (0); } else { /* This rx interrupt must be for a control read status * stage packet. */ UDCDBG ("ACK on EP0 control read status stage packet"); /* deselect EP0 rx FIFO */ outw (0, UDC_EP_NUM); } } else if (status & UDC_STALL) { UDCDBG ("EP0 stall during RX"); /* deselect EP0 rx FIFO */ outw (0, UDC_EP_NUM); } else { /* deselect EP0 rx FIFO */ outw (0, UDC_EP_NUM); } } /* Handle endpoint 0 TX interrupt * This routine implements TRM Figure 14-18. */ static void omap1510_udc_ep0_tx (struct usb_endpoint_instance *endpoint) { unsigned short status; struct usb_device_request *request = &ep0_urb->device_request; UDCDBG ("TX on EP0"); /* select EP0 TX FIFO */ outw (UDC_EP_Dir | UDC_EP_Sel, UDC_EP_NUM); status = inw (UDC_STAT_FLG); if (status & UDC_ACK) { /* Check direction */ if ((request->bmRequestType & USB_REQ_DIRECTION_MASK) == USB_REQ_HOST2DEVICE) { /* This tx interrupt must be for a control write status * stage packet. */ UDCDBG ("ACK on EP0 control write status stage packet"); /* deselect EP0 TX FIFO */ outw (UDC_EP_Dir, UDC_EP_NUM); } else { /* This tx interrupt must be for a control read data * stage packet. */ int wLength = le16_to_cpu (request->wLength); /* Update our count of bytes sent so far in this * transfer. */ endpoint->sent += endpoint->last; /* We are finished with this transfer if we have sent * all of the bytes in our tx urb (urb->actual_length) * unless we need a zero-length terminating packet. We * need a zero-length terminating packet if we returned * fewer bytes than were requested (wLength) by the host, * and the number of bytes we returned is an exact * multiple of the packet size endpoint->tx_packetSize. */ if ((endpoint->sent == ep0_urb->actual_length) && ((ep0_urb->actual_length == wLength) || (endpoint->last != endpoint->tx_packetSize))) { /* Done with control read data stage. */ UDCDBG ("control read data stage complete"); /* deselect EP0 TX FIFO */ outw (UDC_EP_Dir, UDC_EP_NUM); /* select EP0 RX FIFO to prepare for control * read status stage. */ outw (UDC_EP_Sel, UDC_EP_NUM); /* clear the EP0 RX FIFO */ outw (UDC_Clr_EP, UDC_CTRL); /* enable the EP0 RX FIFO */ outw (UDC_Set_FIFO_En, UDC_CTRL); /* deselect the EP0 RX FIFO */ outw (0, UDC_EP_NUM); } else { /* We still have another packet of data to send * in this control read data stage or else we * need a zero-length terminating packet. */ UDCDBG ("ACK control read data stage packet"); omap1510_write_noniso_tx_fifo (endpoint); /* enable the EP0 tx FIFO to start transmission */ outw (UDC_Set_FIFO_En, UDC_CTRL); /* deselect EP0 TX FIFO */ outw (UDC_EP_Dir, UDC_EP_NUM); } } } else if (status & UDC_STALL) { UDCDBG ("EP0 stall during TX"); /* deselect EP0 TX FIFO */ outw (UDC_EP_Dir, UDC_EP_NUM); } else { /* deselect EP0 TX FIFO */ outw (UDC_EP_Dir, UDC_EP_NUM); } } /* Handle RX transaction on non-ISO endpoint. * This function implements TRM Figure 14-27. * The ep argument is a physical endpoint number for a non-ISO OUT endpoint * in the range 1 to 15. */ static void omap1510_udc_epn_rx (int ep) { unsigned short status; /* Check endpoint status */ status = inw (UDC_STAT_FLG); if (status & UDC_ACK) { int nbytes; struct usb_endpoint_instance *endpoint = omap1510_find_ep (ep); nbytes = omap1510_read_noniso_rx_fifo (endpoint); usbd_rcv_complete (endpoint, nbytes, 0); /* enable rx FIFO to prepare for next packet */ outw (UDC_Set_FIFO_En, UDC_CTRL); } else if (status & UDC_STALL) { UDCDBGA ("STALL on RX endpoint %d", ep); } else if (status & UDC_NAK) { UDCDBGA ("NAK on RX ep %d", ep); } else { serial_printf ("omap-bi: RX on ep %d with status %x", ep, status); } } /* Handle TX transaction on non-ISO endpoint. * This function implements TRM Figure 14-29. * The ep argument is a physical endpoint number for a non-ISO IN endpoint * in the range 16 to 30. */ static void omap1510_udc_epn_tx (int ep) { unsigned short status; /*serial_printf("omap1510_udc_epn_tx( %x )\n",ep); */ /* Check endpoint status */ status = inw (UDC_STAT_FLG); if (status & UDC_ACK) { struct usb_endpoint_instance *endpoint = omap1510_find_ep (ep); /* We need to transmit a terminating zero-length packet now if * we have sent all of the data in this URB and the transfer * size was an exact multiple of the packet size. */ if (endpoint->tx_urb && (endpoint->last == endpoint->tx_packetSize) && (endpoint->tx_urb->actual_length - endpoint->sent - endpoint->last == 0)) { /* Prepare to transmit a zero-length packet. */ endpoint->sent += endpoint->last; /* write 0 bytes of data to FIFO */ omap1510_write_noniso_tx_fifo (endpoint); /* enable tx FIFO to start transmission */ outw (UDC_Set_FIFO_En, UDC_CTRL); } else if (endpoint->tx_urb && endpoint->tx_urb->actual_length) { /* retire the data that was just sent */ usbd_tx_complete (endpoint); /* Check to see if we have more data ready to transmit * now. */ if (endpoint->tx_urb && endpoint->tx_urb->actual_length) { /* write data to FIFO */ omap1510_write_noniso_tx_fifo (endpoint); /* enable tx FIFO to start transmission */ outw (UDC_Set_FIFO_En, UDC_CTRL); } } } else if (status & UDC_STALL) { UDCDBGA ("STALL on TX endpoint %d", ep); } else if (status & UDC_NAK) { UDCDBGA ("NAK on TX endpoint %d", ep); } else { /*serial_printf("omap-bi: TX on ep %d with status %x\n", ep, status); */ } } /* ------------------------------------------------------------------------------- */ /* Handle general USB interrupts and dispatch according to type. * This function implements TRM Figure 14-13. */ void omap1510_udc_irq (void) { u16 irq_src = inw (UDC_IRQ_SRC); int valid_irq = 0; if (!(irq_src & ~UDC_SOF_Flg)) /* ignore SOF interrupts ) */ return; UDCDBGA ("< IRQ #%d start >- %x", udc_interrupts, irq_src); /*serial_printf("< IRQ #%d start >- %x\n", udc_interrupts, irq_src); */ if (irq_src & UDC_DS_Chg) { /* Device status changed */ omap1510_udc_state_changed (); valid_irq++; } if (irq_src & UDC_EP0_RX) { /* Endpoint 0 receive */ outw (UDC_EP0_RX, UDC_IRQ_SRC); /* ack interrupt */ omap1510_udc_ep0_rx (udc_device->bus->endpoint_array + 0); valid_irq++; } if (irq_src & UDC_EP0_TX) { /* Endpoint 0 transmit */ outw (UDC_EP0_TX, UDC_IRQ_SRC); /* ack interrupt */ omap1510_udc_ep0_tx (udc_device->bus->endpoint_array + 0); valid_irq++; } if (irq_src & UDC_Setup) { /* Device setup */ omap1510_udc_setup (udc_device->bus->endpoint_array + 0); valid_irq++; } /*if (!valid_irq) */ /* serial_printf("unknown interrupt, IRQ_SRC %.4x\n", irq_src); */ UDCDBGA ("< IRQ #%d end >", udc_interrupts); udc_interrupts++; } /* This function implements TRM Figure 14-26. */ void omap1510_udc_noniso_irq (void) { unsigned short epnum; unsigned short irq_src = inw (UDC_IRQ_SRC); int valid_irq = 0; if (!(irq_src & (UDC_EPn_RX | UDC_EPn_TX))) return; UDCDBGA ("non-ISO IRQ, IRQ_SRC %x", inw (UDC_IRQ_SRC)); if (irq_src & UDC_EPn_RX) { /* Endpoint N OUT transaction */ /* Determine the endpoint number for this interrupt */ epnum = (inw (UDC_EPN_STAT) & 0x0f00) >> 8; UDCDBGA ("RX on ep %x", epnum); /* acknowledge interrupt */ outw (UDC_EPn_RX, UDC_IRQ_SRC); if (epnum) { /* select the endpoint FIFO */ outw (UDC_EP_Sel | epnum, UDC_EP_NUM); omap1510_udc_epn_rx (epnum); /* deselect the endpoint FIFO */ outw (epnum, UDC_EP_NUM); } valid_irq++; } if (irq_src & UDC_EPn_TX) { /* Endpoint N IN transaction */ /* Determine the endpoint number for this interrupt */ epnum = (inw (UDC_EPN_STAT) & 0x000f) | USB_DIR_IN; UDCDBGA ("TX on ep %x", epnum); /* acknowledge interrupt */ outw (UDC_EPn_TX, UDC_IRQ_SRC); if (epnum) { /* select the endpoint FIFO */ outw (UDC_EP_Sel | UDC_EP_Dir | epnum, UDC_EP_NUM); omap1510_udc_epn_tx (epnum); /* deselect the endpoint FIFO */ outw (UDC_EP_Dir | epnum, UDC_EP_NUM); } valid_irq++; } if (!valid_irq) serial_printf (": unknown non-ISO interrupt, IRQ_SRC %.4x\n", irq_src); } /* ------------------------------------------------------------------------------- */ /* * Start of public functions. */ /* Called to start packet transmission. */ void udc_endpoint_write (struct usb_endpoint_instance *endpoint) { unsigned short epnum = endpoint->endpoint_address & USB_ENDPOINT_NUMBER_MASK; UDCDBGA ("Starting transmit on ep %x", epnum); if (endpoint->tx_urb) { /* select the endpoint FIFO */ outw (UDC_EP_Sel | UDC_EP_Dir | epnum, UDC_EP_NUM); /* write data to FIFO */ omap1510_write_noniso_tx_fifo (endpoint); /* enable tx FIFO to start transmission */ outw (UDC_Set_FIFO_En, UDC_CTRL); /* deselect the endpoint FIFO */ outw (UDC_EP_Dir | epnum, UDC_EP_NUM); } } /* Start to initialize h/w stuff */ int udc_init (void) { u16 udc_rev; uchar value; udc_device = NULL; UDCDBG ("starting"); /* Check peripheral reset. Must be 1 to make sure MPU TIPB peripheral reset is inactive */ UDCREG (ARM_RSTCT2); /* Set and check clock control. * We might ought to be using the clock control API to do * this instead of fiddling with the clock registers directly * here. */ outw ((1 << 4) | (1 << 5), CLOCK_CTRL); UDCREG (CLOCK_CTRL); /* Set and check APLL */ outw (0x0008, APLL_CTRL); UDCREG (APLL_CTRL); /* Set and check DPLL */ outw (0x2210, DPLL_CTRL); UDCREG (DPLL_CTRL); /* Set and check SOFT */ outw ((1 << 4) | (1 << 3) | 1, SOFT_REQ); /* Short delay to wait for DPLL */ udelay (1000); /* Print banner with device revision */ udc_rev = inw (UDC_REV) & 0xff; printf ("USB: TI OMAP1510 USB function module rev %d.%d\n", udc_rev >> 4, udc_rev & 0xf); #ifdef CONFIG_OMAP_SX1 i2c_read (0x32, 0x04, 1, &value, 1); value |= 0x04; i2c_write (0x32, 0x04, 1, &value, 1); i2c_read (0x32, 0x03, 1, &value, 1); value |= 0x01; i2c_write (0x32, 0x03, 1, &value, 1); #endif /* The VBUS_MODE bit selects whether VBUS detection is done via * software (1) or hardware (0). When software detection is * selected, VBUS_CTRL selects whether USB is not connected (0) * or connected (1). */ outl (inl (FUNC_MUX_CTRL_0) | UDC_VBUS_MODE, FUNC_MUX_CTRL_0); outl (inl (FUNC_MUX_CTRL_0) & ~UDC_VBUS_CTRL, FUNC_MUX_CTRL_0); UDCREGL (FUNC_MUX_CTRL_0); /* * At this point, device is ready for configuration... */ UDCDBG ("disable USB interrupts"); outw (0, UDC_IRQ_EN); UDCREG (UDC_IRQ_EN); UDCDBG ("disable USB DMA"); outw (0, UDC_DMA_IRQ_EN); UDCREG (UDC_DMA_IRQ_EN); UDCDBG ("initialize SYSCON1"); outw (UDC_Self_Pwr | UDC_Pullup_En, UDC_SYSCON1); UDCREG (UDC_SYSCON1); return 0; } /* Stall endpoint */ static void udc_stall_ep (unsigned int ep_addr) { /*int ep_addr = PHYS_EP_TO_EP_ADDR(ep); */ int ep_num = ep_addr & USB_ENDPOINT_NUMBER_MASK; UDCDBGA ("stall ep_addr %d", ep_addr); /* REVISIT? * The OMAP TRM section 14.2.4.2 says we must check that the FIFO * is empty before halting the endpoint. The current implementation * doesn't check that the FIFO is empty. */ if (!ep_num) { outw (UDC_Stall_Cmd, UDC_SYSCON2); } else if ((ep_addr & USB_ENDPOINT_DIR_MASK) == USB_DIR_OUT) { if (inw (UDC_EP_RX (ep_num)) & UDC_EPn_RX_Valid) { /* we have a valid rx endpoint, so halt it */ outw (UDC_EP_Sel | ep_num, UDC_EP_NUM); outw (UDC_Set_Halt, UDC_CTRL); outw (ep_num, UDC_EP_NUM); } } else { if (inw (UDC_EP_TX (ep_num)) & UDC_EPn_TX_Valid) { /* we have a valid tx endpoint, so halt it */ outw (UDC_EP_Sel | UDC_EP_Dir | ep_num, UDC_EP_NUM); outw (UDC_Set_Halt, UDC_CTRL); outw (ep_num, UDC_EP_NUM); } } } /* Reset endpoint */ #if 0 static void udc_reset_ep (unsigned int ep_addr) { /*int ep_addr = PHYS_EP_TO_EP_ADDR(ep); */ int ep_num = ep_addr & USB_ENDPOINT_NUMBER_MASK; UDCDBGA ("reset ep_addr %d", ep_addr); if (!ep_num) { /* control endpoint 0 can't be reset */ } else if ((ep_addr & USB_ENDPOINT_DIR_MASK) == USB_DIR_OUT) { UDCDBGA ("UDC_EP_RX(%d) = 0x%04x", ep_num, inw (UDC_EP_RX (ep_num))); if (inw (UDC_EP_RX (ep_num)) & UDC_EPn_RX_Valid) { /* we have a valid rx endpoint, so reset it */ outw (ep_num | UDC_EP_Sel, UDC_EP_NUM); outw (UDC_Reset_EP, UDC_CTRL); outw (ep_num, UDC_EP_NUM); UDCDBGA ("OUT endpoint %d reset", ep_num); } } else { UDCDBGA ("UDC_EP_TX(%d) = 0x%04x", ep_num, inw (UDC_EP_TX (ep_num))); /* Resetting of tx endpoints seems to be causing the USB function * module to fail, which causes problems when the driver is * uninstalled. We'll skip resetting tx endpoints for now until * we figure out what the problem is. */ #if 0 if (inw (UDC_EP_TX (ep_num)) & UDC_EPn_TX_Valid) { /* we have a valid tx endpoint, so reset it */ outw (ep_num | UDC_EP_Dir | UDC_EP_Sel, UDC_EP_NUM); outw (UDC_Reset_EP, UDC_CTRL); outw (ep_num | UDC_EP_Dir, UDC_EP_NUM); UDCDBGA ("IN endpoint %d reset", ep_num); } #endif } } #endif /* ************************************************************************** */ /** * udc_check_ep - check logical endpoint * * Return physical endpoint number to use for this logical endpoint or zero if not valid. */ #if 0 int udc_check_ep (int logical_endpoint, int packetsize) { if ((logical_endpoint == 0x80) || ((logical_endpoint & 0x8f) != logical_endpoint)) { return 0; } switch (packetsize) { case 8: case 16: case 32: case 64: case 128: case 256: case 512: break; default: return 0; } return EP_ADDR_TO_PHYS_EP (logical_endpoint); } #endif /* * udc_setup_ep - setup endpoint * * Associate a physical endpoint with endpoint_instance */ void udc_setup_ep (struct usb_device_instance *device, unsigned int ep, struct usb_endpoint_instance *endpoint) { UDCDBGA ("setting up endpoint addr %x", endpoint->endpoint_address); /* This routine gets called by bi_modinit for endpoint 0 and from * bi_config for all of the other endpoints. bi_config gets called * during the DEVICE_CREATE, DEVICE_CONFIGURED, and * DEVICE_SET_INTERFACE events. We need to reconfigure the OMAP packet * RAM after bi_config scans the selected device configuration and * initializes the endpoint structures, but before this routine enables * the OUT endpoint FIFOs. Since bi_config calls this routine in a * loop for endpoints 1 through UDC_MAX_ENDPOINTS, we reconfigure our * packet RAM here when ep==1. * I really hate to do this here, but it seems like the API exported * by the USB bus interface controller driver to the usbd-bi module * isn't quite right so there is no good place to do this. */ if (ep == 1) { omap1510_deconfigure_device (); omap1510_configure_device (device); } if (endpoint && (ep < UDC_MAX_ENDPOINTS)) { int ep_addr = endpoint->endpoint_address; if (!ep_addr) { /* nothing to do for endpoint 0 */ } else if ((ep_addr & USB_ENDPOINT_DIR_MASK) == USB_DIR_IN) { /* nothing to do for IN (tx) endpoints */ } else { /* OUT (rx) endpoint */ if (endpoint->rcv_packetSize) { /*struct urb* urb = &(urb_out_array[ep&0xFF]); */ /*urb->endpoint = endpoint; */ /*urb->device = device; */ /*urb->buffer_length = sizeof(urb->buffer); */ /*endpoint->rcv_urb = urb; */ omap1510_prepare_endpoint_for_rx (ep_addr); } } } } /** * udc_disable_ep - disable endpoint * @ep: * * Disable specified endpoint */ #if 0 void udc_disable_ep (unsigned int ep_addr) { /*int ep_addr = PHYS_EP_TO_EP_ADDR(ep); */ int ep_num = ep_addr & USB_ENDPOINT_NUMBER_MASK; struct usb_endpoint_instance *endpoint = omap1510_find_ep (ep_addr); /*udc_device->bus->endpoint_array + ep; */ UDCDBGA ("disable ep_addr %d", ep_addr); if (!ep_num) { /* nothing to do for endpoint 0 */ ; } else if ((ep_addr & USB_ENDPOINT_DIR_MASK) == USB_DIR_IN) { if (endpoint->tx_packetSize) { /* we have a valid tx endpoint */ /*usbd_flush_tx(endpoint); */ endpoint->tx_urb = NULL; } } else { if (endpoint->rcv_packetSize) { /* we have a valid rx endpoint */ /*usbd_flush_rcv(endpoint); */ endpoint->rcv_urb = NULL; } } } #endif /* ************************************************************************** */ /** * udc_connected - is the USB cable connected * * Return non-zero if cable is connected. */ #if 0 int udc_connected (void) { return ((inw (UDC_DEVSTAT) & UDC_ATT) == UDC_ATT); } #endif /* Turn on the USB connection by enabling the pullup resistor */ void udc_connect (void) { UDCDBG ("connect, enable Pullup"); outl (0x00000018, FUNC_MUX_CTRL_D); } /* Turn off the USB connection by disabling the pullup resistor */ void udc_disconnect (void) { UDCDBG ("disconnect, disable Pullup"); outl (0x00000000, FUNC_MUX_CTRL_D); } /* ************************************************************************** */ /* * udc_disable_interrupts - disable interrupts * switch off interrupts */ #if 0 void udc_disable_interrupts (struct usb_device_instance *device) { UDCDBG ("disabling all interrupts"); outw (0, UDC_IRQ_EN); } #endif /* ************************************************************************** */ /** * udc_ep0_packetsize - return ep0 packetsize */ #if 0 int udc_ep0_packetsize (void) { return EP0_PACKETSIZE; } #endif /* Switch on the UDC */ void udc_enable (struct usb_device_instance *device) { UDCDBGA ("enable device %p, status %d", device, device->status); /* initialize driver state variables */ udc_devstat = 0; /* Save the device structure pointer */ udc_device = device; /* Setup ep0 urb */ if (!ep0_urb) { ep0_urb = usbd_alloc_urb (udc_device, udc_device->bus->endpoint_array); } else { serial_printf ("udc_enable: ep0_urb already allocated %p\n", ep0_urb); } UDCDBG ("Check clock status"); UDCREG (STATUS_REQ); /* The VBUS_MODE bit selects whether VBUS detection is done via * software (1) or hardware (0). When software detection is * selected, VBUS_CTRL selects whether USB is not connected (0) * or connected (1). */ outl (inl (FUNC_MUX_CTRL_0) | UDC_VBUS_CTRL | UDC_VBUS_MODE, FUNC_MUX_CTRL_0); UDCREGL (FUNC_MUX_CTRL_0); omap1510_configure_device (device); } /* Switch off the UDC */ void udc_disable (void) { UDCDBG ("disable UDC"); omap1510_deconfigure_device (); /* The VBUS_MODE bit selects whether VBUS detection is done via * software (1) or hardware (0). When software detection is * selected, VBUS_CTRL selects whether USB is not connected (0) * or connected (1). */ outl (inl (FUNC_MUX_CTRL_0) | UDC_VBUS_MODE, FUNC_MUX_CTRL_0); outl (inl (FUNC_MUX_CTRL_0) & ~UDC_VBUS_CTRL, FUNC_MUX_CTRL_0); UDCREGL (FUNC_MUX_CTRL_0); /* Free ep0 URB */ if (ep0_urb) { /*usbd_dealloc_urb(ep0_urb); */ ep0_urb = NULL; } /* Reset device pointer. * We ought to do this here to balance the initialization of udc_device * in udc_enable, but some of our other exported functions get called * by the bus interface driver after udc_disable, so we have to hang on * to the device pointer to avoid a null pointer dereference. */ /* udc_device = NULL; */ } /** * udc_startup - allow udc code to do any additional startup */ void udc_startup_events (struct usb_device_instance *device) { /* The DEVICE_INIT event puts the USB device in the state STATE_INIT. */ usbd_device_event_irq (device, DEVICE_INIT, 0); /* The DEVICE_CREATE event puts the USB device in the state * STATE_ATTACHED. */ usbd_device_event_irq (device, DEVICE_CREATE, 0); /* Some USB controller driver implementations signal * DEVICE_HUB_CONFIGURED and DEVICE_RESET events here. * DEVICE_HUB_CONFIGURED causes a transition to the state STATE_POWERED, * and DEVICE_RESET causes a transition to the state STATE_DEFAULT. * The OMAP USB client controller has the capability to detect when the * USB cable is connected to a powered USB bus via the ATT bit in the * DEVSTAT register, so we will defer the DEVICE_HUB_CONFIGURED and * DEVICE_RESET events until later. */ udc_enable (device); } #endif