/* SPDX-License-Identifier: GPL-2.0+ */ /* * (C) Copyright 2012 * Holger Brunck, Keymile GmbH Hannover, * Christian Herzig, Keymile AG Switzerland, */ #ifndef __CONFIG_H #define __CONFIG_H /* KMBEC FPGA (PRIO) */ #define CONFIG_SYS_KMBEC_FPGA_BASE 0xE8000000 #define CONFIG_SYS_KMBEC_FPGA_SIZE 64 #define CONFIG_HOSTNAME "kmcoge5ne" #define CONFIG_KM_BOARD_NAME "kmcoge5ne" #define CONFIG_KM_DEF_NETDEV "netdev=eth1\0" #define CONFIG_NAND_ECC_BCH #define CONFIG_NAND_KMETER1 #define CONFIG_SYS_MAX_NAND_DEVICE 1 #define NAND_MAX_CHIPS 1 #define CONFIG_SYS_NAND_BASE CONFIG_SYS_KMBEC_FPGA_BASE /* PRIO_BASE_ADDRESS */ #define CONFIG_KM_UBI_PARTITION_NAME_BOOT "ubi0" #define CONFIG_KM_UBI_PARTITION_NAME_APP "ubi1" /* * High Level Configuration Options */ #define CONFIG_QE /* Has QE */ /* include common defines/options for all Keymile boards */ #include "km/keymile-common.h" #include "km/km-powerpc.h" /* * System Clock Setup */ #define CONFIG_83XX_CLKIN 66000000 #define CONFIG_SYS_CLK_FREQ 66000000 #define CONFIG_83XX_PCICLK 66000000 /* * IMMR new address */ #define CONFIG_SYS_IMMR 0xE0000000 /* * Bus Arbitration Configuration Register (ACR) */ #define CONFIG_SYS_ACR_PIPE_DEP 3 /* pipeline depth 4 transactions */ #define CONFIG_SYS_ACR_RPTCNT 3 /* 4 consecutive transactions */ #define CONFIG_SYS_ACR_APARK 0 /* park bus to master (below) */ #define CONFIG_SYS_ACR_PARKM 3 /* parking master = QuiccEngine */ /* * DDR Setup */ #define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */ #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE #define CONFIG_SYS_SDRAM_BASE2 (CONFIG_SYS_SDRAM_BASE + 0x10000000) /* +256M */ #define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN | \ DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05) #define CFG_83XX_DDR_USES_CS0 /* * Manually set up DDR parameters */ #define CONFIG_DDR_II #define CONFIG_SYS_DDR_SIZE 2048 /* MB */ /* * The reserved memory */ #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ #define CONFIG_SYS_FLASH_BASE 0xF0000000 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) #define CONFIG_SYS_RAMBOOT #endif /* Reserve 768 kB for Mon */ #define CONFIG_SYS_MONITOR_LEN (768 * 1024) /* * Initial RAM Base Address Setup */ #define CONFIG_SYS_INIT_RAM_LOCK #define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ #define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* End of used area in RAM */ #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ GENERATED_GBL_DATA_SIZE) /* * Init Local Bus Memory Controller: * * Bank Bus Machine PortSz Size Device * ---- --- ------- ------ ----- ------ * 0 Local GPCM 16 bit 256MB FLASH * 1 Local GPCM 8 bit 128MB GPIO/PIGGY * */ /* * FLASH on the Local Bus */ #define CONFIG_SYS_FLASH_SIZE 256 /* max FLASH size is 256M */ #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks */ #define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sects on one chip */ #define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } /* * PRIO1/PIGGY on the local bus CS1 */ /* * Serial Port */ #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE 1 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500) #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600) /* * QE UEC ethernet configuration */ #define CONFIG_UEC_ETH #define CONFIG_ETHPRIME "UEC0" #define CONFIG_UEC_ETH1 /* GETH1 */ #define UEC_VERBOSE_DEBUG 1 #ifdef CONFIG_UEC_ETH1 #define CONFIG_SYS_UEC1_UCC_NUM 3 /* UCC4 */ #define CONFIG_SYS_UEC1_RX_CLK QE_CLK_NONE /* not used in RMII Mode */ #define CONFIG_SYS_UEC1_TX_CLK QE_CLK17 #define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH #define CONFIG_SYS_UEC1_PHY_ADDR 0 #define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII #define CONFIG_SYS_UEC1_INTERFACE_SPEED 100 #endif /* * Environment */ #ifndef CONFIG_SYS_RAMBOOT #ifndef CONFIG_ENV_ADDR #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \ CONFIG_SYS_MONITOR_LEN) #endif #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ #ifndef CONFIG_ENV_OFFSET #define CONFIG_ENV_OFFSET (CONFIG_SYS_MONITOR_LEN) #endif /* Address and size of Redundant Environment Sector */ #define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + \ CONFIG_ENV_SECT_SIZE) #define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) #else /* CFG_SYS_RAMBOOT */ #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) #define CONFIG_ENV_SIZE 0x2000 #endif /* CFG_SYS_RAMBOOT */ /* I2C */ #define CONFIG_SYS_I2C #define CONFIG_SYS_NUM_I2C_BUSES 4 #define CONFIG_SYS_I2C_MAX_HOPS 1 #define CONFIG_SYS_I2C_FSL #define CONFIG_SYS_FSL_I2C_SPEED 200000 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 #define CONFIG_SYS_I2C_OFFSET 0x3000 #define CONFIG_SYS_FSL_I2C2_SPEED 200000 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F #define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 #define CONFIG_SYS_I2C_BUSES {{0, {I2C_NULL_HOP} }, \ {0, {{I2C_MUX_PCA9547, 0x70, 2} } }, \ {0, {{I2C_MUX_PCA9547, 0x70, 1} } }, \ {1, {I2C_NULL_HOP} } } #define CONFIG_KM_IVM_BUS 2 /* I2C2 (Mux-Port 1)*/ #if defined(CONFIG_CMD_NAND) #define CONFIG_NAND_KMETER1 #define CONFIG_SYS_MAX_NAND_DEVICE 1 #define CONFIG_SYS_NAND_BASE CONFIG_SYS_KMBEC_FPGA_BASE #endif /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* * Core HID Setup */ #define CONFIG_SYS_HID0_INIT 0x000000000 #define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \ HID0_ENABLE_INSTRUCTION_CACHE) #define CONFIG_SYS_HID2 HID2_HBE /* * Internal Definitions */ #define BOOTFLASH_START 0xF0000000 #define CONFIG_KM_CONSOLE_TTY "ttyS0" /* * Environment Configuration */ #define CONFIG_ENV_OVERWRITE #ifndef CONFIG_KM_DEF_ENV /* if not set by keymile-common.h */ #define CONFIG_KM_DEF_ENV "km-common=empty\0" #endif #ifndef CONFIG_KM_DEF_ARCH #define CONFIG_KM_DEF_ARCH "arch=ppc_82xx\0" #endif #define CONFIG_EXTRA_ENV_SETTINGS \ CONFIG_KM_DEF_ENV \ CONFIG_KM_DEF_ARCH \ "newenv=" \ "prot off "__stringify(CONFIG_ENV_ADDR)" +0x40000 && " \ "era "__stringify(CONFIG_ENV_ADDR)" +0x40000\0" \ "unlock=yes\0" \ "" #if defined(CONFIG_UEC_ETH) #define CONFIG_HAS_ETH0 #endif /* * System IO Setup */ #define CONFIG_SYS_SICRH (SICRH_UC1EOBI | SICRH_UC2E1OBI) /** * DDR RAM settings */ #define CONFIG_SYS_DDR_SDRAM_CFG (\ SDRAM_CFG_SDRAM_TYPE_DDR2 | \ SDRAM_CFG_SREN | \ SDRAM_CFG_HSE) #define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 /** * KMCOGE5NE has 512 MB RAM */ #define CONFIG_SYS_DDR_CS0_CONFIG (\ CSCONFIG_EN | \ CSCONFIG_AP | \ CSCONFIG_ODT_WR_ONLY_CURRENT | \ CSCONFIG_BANK_BIT_3 | \ CSCONFIG_ROW_BIT_13 | \ CSCONFIG_COL_BIT_10) #define CONFIG_SYS_DDR_CLK_CNTL (\ DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05) #define CONFIG_SYS_DDR_INTERVAL (\ (0x080 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \ (0x203 << SDRAM_INTERVAL_REFINT_SHIFT)) #define CONFIG_SYS_DDR_CS0_BNDS 0x0000007f #define CONFIG_SYS_DDRCDR (\ DDRCDR_EN | \ DDRCDR_Q_DRN) #define CONFIG_SYS_DDR_MODE 0x47860452 #define CONFIG_SYS_DDR_MODE2 0x8080c000 #define CONFIG_SYS_DDR_TIMING_0 (\ (2 << TIMING_CFG0_MRS_CYC_SHIFT) | \ (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \ (6 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \ (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \ (0 << TIMING_CFG0_WWT_SHIFT) | \ (0 << TIMING_CFG0_RRT_SHIFT) | \ (0 << TIMING_CFG0_WRT_SHIFT) | \ (0 << TIMING_CFG0_RWT_SHIFT)) #define CONFIG_SYS_DDR_TIMING_1 ((TIMING_CFG1_CASLAT_50) | \ (2 << TIMING_CFG1_WRTORD_SHIFT) | \ (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \ (3 << TIMING_CFG1_WRREC_SHIFT) | \ (7 << TIMING_CFG1_REFREC_SHIFT) | \ (3 << TIMING_CFG1_ACTTORW_SHIFT) | \ (8 << TIMING_CFG1_ACTTOPRE_SHIFT) | \ (3 << TIMING_CFG1_PRETOACT_SHIFT)) #define CONFIG_SYS_DDR_TIMING_2 (\ (0xa << TIMING_CFG2_FOUR_ACT_SHIFT) | \ (3 << TIMING_CFG2_CKE_PLS_SHIFT) | \ (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \ (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \ (4 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \ (5 << TIMING_CFG2_CPO_SHIFT) | \ (0 << TIMING_CFG2_ADD_LAT_SHIFT)) #define CONFIG_SYS_DDR_TIMING_3 0x00000000 /* EEprom support */ #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* * Local Bus Configuration & Clock Setup */ #define CONFIG_SYS_LCRR_DBYP LCRR_DBYP #define CONFIG_SYS_LCRR_EADC LCRR_EADC_2 #define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_4 /* * PAXE on the local bus CS3 */ #define CONFIG_SYS_PAXE_BASE 0xA0000000 #define CONFIG_SYS_PAXE_SIZE 256 /* * BFTIC3 on the local bus CS4 */ #define CONFIG_SYS_BFTIC3_BASE 0xB0000000 #define CONFIG_SYS_BFTIC3_SIZE 256 /* enable POST tests */ #define CONFIG_POST (CONFIG_SYS_POST_MEMORY|CONFIG_SYS_POST_MEM_REGIONS) #define CONFIG_POST_EXTERNAL_WORD_FUNCS /* use own functions, not generic */ #define CPM_POST_WORD_ADDR CONFIG_SYS_MEMTEST_END #define CONFIG_TESTPIN_REG gprt3 /* for kmcoge5ne */ #define CONFIG_TESTPIN_MASK 0x20 /* for kmcoge5ne */ #endif /* CONFIG */