| Age | Commit message (Expand) | Author |
|---|
| 2000-01-01 | don't do as many error checks when delay word/range is overriddenINSTRUMENT_6_2_25 | Mike |
| 2000-01-01 | more useful error message when setting CH2 delay cal | Mike |
| 2000-01-01 | more specific errors during cal min/max check, and more initial cal points | Mike |
| 2017-05-25 | version bumpINSTRUMENT_6_2_24 | Michael J. Chudobiak |
| 2017-05-23 | fix min/max cal point check for units with non-zero rst amplitude (AVRQ-5-B-AHV) | Michael J. Chudobiak |
| 1970-01-01 | version bumpINSTRUMENT_6_2_23 | mjc |
| 1970-01-01 | Enforce minimum ampl magnitude (based on zero_equiv_ampl) in AVRQ -AHV, -XHV ... | mjc |
| 2000-01-01 | version bumpINSTRUMENT_6_2_22 | mjc |
| 2000-01-01 | self-cal needs at least 2 periods for PW cal measurement time | mjc |
| 2000-01-01 | version bumpINSTRUMENT_6_2_21 | mjc |
| 2000-01-01 | make self-cal min count configurable | mjc |
| 2000-01-01 | make self-cal reference frequency configurable | Mike |
| 2000-01-01 | added ability to increase output-on delay | Mike |
| 2000-01-01 | added get_float_with_min function | Mike |
| 2000-01-01 | added get_bounded_float function | Mike |
| 2017-03-22 | reduced minimum self-cal measurement from 100us to 40us (0.25% resolution) | Michael J. Chudobiak |
| 2016-12-12 | version bumpINSTRUMENT_6_2_20 | Michael J. Chudobiak |
| 2016-12-12 | Revert force-output-on during timing cal option. Too complex, little reward. | Michael J. Chudobiak |
| 1970-01-01 | version bumpINSTRUMENT_6_2_19 | root |
| 1970-01-01 | allow option to force output on during timing cal | root |
| 2000-01-01 | version bumpINSTRUMENT_6_2_18 | mjc |
| 2000-01-01 | Additional PRF points for 0.1 Hz operation | mjc |
| 2000-01-01 | version bumpINSTRUMENT_6_2_17 | root |
| 2000-01-01 | fixed incorrect init of burst, prf integers | root |
| 2000-01-01 | version bumpINSTRUMENT_6_2_16 | root |
| 2000-01-01 | choose initial PW cal points assuming DDU #2 removed | root |
| 2000-01-01 | toggle both polarities of trigger lines on optocoupler boot toggleINSTRUMENT_6_2_15 | root |
| 2000-01-01 | version bump | root |
| 2000-01-01 | try to turn output off on power fail | root |
| 2000-01-01 | version bumpINSTRUMENT_6_2_14 | root |
| 2000-01-01 | fix last patch | root |
| 2016-09-09 | additional initial cal point per range for burst mode | Michael J. Chudobiak |
| 2016-09-09 | additional address comments in flash for clarity | Michael J. Chudobiak |
| 1970-01-01 | bumped versionINSTRUMENT_6_2_13 | root |
| 1970-01-01 | fix non-working linear interpolation, = vs == | root |
| 2000-01-01 | set minimum allowed PRF during PW/delay calibration | root |
| 2000-01-01 | version bump to 6.2.12INSTRUMENT_6_2_12 | root |
| 2000-01-01 | remove failed 3 point interpolation scheme | root |
| 2000-01-01 | add, but don't use, 3 pt inversion interpolation - doesn't work well! | root |
| 2000-01-01 | separate function for inverse interpolation of X given desired Y | root |
| 2000-01-01 | separate function for linear interpolation of X given desired Y | root |
| 1970-01-01 | add PW distortion for AVR-E, AVIR, AVL. 0% at max amplitude, 100% below set v...INSTRUMENT_6_2_11b | root |
| 1970-01-01 | version bumpINSTRUMENT_6_2_11 | root |
| 1970-01-01 | fix error in pw/delay control introduced by voltage-controlled 2CH delay | root |
| 1970-01-01 | version bump, for 2CHPPINSTRUMENT_6_2_10 | root |
| 1970-01-01 | for 2CHPP CH2 delay cal, use existing parameters | root |
| 1970-01-01 | use delay magnitude to set test PRF since it can be negative, and simplify ex... | root |
| 1970-01-01 | first attempt at implementing CH2 2CHPP delay function | root |
| 1970-01-01 | added volt_ctrl_delay, for 2CHPP on CH2 | root |
| 1970-01-01 | move attenuator code out of CH1-only block, so it works for CH2INSTRUMENT_6_2_09c | root |
