| Age | Commit message (Expand) | Author |
|---|
| 2000-01-01 | version bumpINSTRUMENT_6_4_25 | Mike |
| 2000-01-01 | Test encoder against min change and min speed, for free-rolling defective enc... | Mike |
| 2000-01-01 | version bumpINSTRUMENT_6_4_24 | Mike |
| 2000-01-01 | Do not switch polarity relay line in dual-chan dual-pol units, if CH2 ignores... | Mike |
| 2000-01-01 | Major reworking. Set_VI_Control now stores its calculation results for later ...INSTRUMENT_6_4_23d | Mike |
| 2000-01-01 | fully implement disable timing cal percentage check | Mike |
| 2000-01-01 | debug messages showing XTR line changesINSTRUMENT_6_4_23c | Mike |
| 2000-01-01 | remove broken CH2 TTL/ECL logic code, not used in any instruments now | Mike |
| 2000-01-01 | +/- button not working as expected first press after turn-on, fixed. Better d... | Mike |
| 2000-01-01 | Allow CH2 DLY to control trigger PW (for -2CHX). Better debug messages.INSTRUMENT_6_4_23b | Mike |
| 2000-01-01 | version bumpINSTRUMENT_6_4_23 | Mike |
| 2000-01-01 | Dump valid points to console when querying range info, to debug errant cal po... | Mike |
| 2000-01-01 | version bumpINSTRUMENT_6_4_22 | Mike |
| 2000-01-01 | add ability to temporarily disable timing cal percentage check, for burst/sep... | Mike |
| 2000-01-01 | version bumpINSTRUMENT_6_4_21 | Mike |
| 2020-07-27 | add support for new jig pin on keypad 104G | Michael J. Chudobiak |
| 2000-01-01 | version bumpINSTRUMENT_6_4_20 | Mike |
| 2000-01-01 | Only ignore polarity when shown to user. Use polarity when considering calibr... | Mike |
| 2000-01-01 | let rise time go to the lowest hardware-possible value, not just the specifie...INSTRUMENT_6_4_19c | Mike |
| 2000-01-01 | reduce min rise time cal points to reflect faster 266D | Mike |
| 2000-01-01 | same as last, missed a spotINSTRUMENT_6_4_19b | Mike |
| 2000-01-01 | tagged for 6.4.19INSTRUMENT_6_4_19 | Mike |
| 2000-01-01 | ampl_zero_equiv can be large in some AVRQ units, use smallest_allowed_number ... | Mike |
| 2000-01-01 | fix encoder clearingINSTRUMENT_6_4_18b | Mike |
| 2000-01-01 | version bumpINSTRUMENT_6_4_18 | Mike |
| 2000-01-01 | ignore tiniest encoder steps | Mike |
| 2020-03-18 | version bumpINSTRUMENT_6_4_17 | Michael J. Chudobiak |
| 2020-03-18 | add an "ALIVE" output, to switch on VCC2 in AVRQ (for example) | Michael J. Chudobiak |
| 2000-01-01 | version bumpINSTRUMENT_6_4_16 | Mike |
| 2000-01-01 | allow mult/div by 10 of burst count values | Mike |
| 2000-01-01 | Simplify needlessly complex error handling when adjusting encoder | Mike |
| 2000-01-01 | Simplify needlessly complex error handling when mult/div menu values | Mike |
| 2000-01-01 | Don't move arrow if only one mode. Fix amplitude mode list.INSTRUMENT_6_4_15b | Mike |
| 2000-01-01 | version bumpINSTRUMENT_6_4_15 | Mike |
| 2000-01-01 | tidy amplitude menu code | Mike |
| 2000-01-01 | Don't write GPIB address to flash until CHANGE button pressed, to avoid weird... | Mike |
| 2000-01-01 | version bumpINSTRUMENT_6_4_14 | Mike |
| 2000-01-01 | another divide-by-zero error | Mike |
| 2000-01-01 | version bumpINSTRUMENT_6_4_13 | Mike |
| 2019-07-16 | forward port of avg_error calc divide-by-zero fix from AVR-8A-B-P-QTKB repair | Michael J. Chudobiak |
| 2000-01-01 | version bumpINSTRUMENT_6_4_12 | Mike |
| 2000-01-01 | do not reset state before calibrating rise time in AVRQ | Mike |
| 2019-01-08 | version bumpINSTRUMENT_6_4_11 | Michael J. Chudobiak |
| 2019-01-08 | always enable vxi now | Michael J. Chudobiak |
| 2000-01-01 | fix min/max ampl/vout balancing when nulling delay shift calINSTRUMENT_6_4_10b | Mike |
| 2000-01-01 | version bumpINSTRUMENT_6_4_10 | Mike |
| 2000-01-01 | fix ampl min/max checks when max_ampl is limited by max_vout (some -OT units) | Mike |
| 2018-11-23 | version bumpINSTRUMENT_6_4_09 | Michael J. Chudobiak |
| 2018-11-23 | enable VXI on unprogrammed boards, for testing without GPIB | Michael J. Chudobiak |
| 2000-01-01 | make max step size deviation configurableINSTRUMENT_6_4_08b | Mike |
