| Age | Commit message (Expand) | Author |
|---|
| 2000-01-01 | add TODO for Monday | Mike |
| 2000-01-01 | do not add redundant settling time flag when changing ampl mode | Mike |
| 2000-01-01 | further refinements to ampl settling time, but need to make it dependent on s... | Mike |
| 2023-11-10 | add an amplitude settling time for SN 14256 repair and future units | Michael J. Chudobiak |
| 2000-01-01 | Do not apply polarity-based PW shift in bot range if bot range is voltage con... | Mike |
| 2000-01-01 | delete an unused variable | Mike |
| 2000-01-01 | Fix crashes caused by uninitialized pointer | Mike |
| 2000-01-01 | reduce ampl_zero_equiv by a factor of 10 in -LV attenuator modeINSTRUMENT_6_4_27c | Mike |
| 2000-01-01 | extended delay when switching attenuators in -LV units | Mike |
| 2000-01-01 | only use attenuators in switchable zout units whem zout is 50 OhmsINSTRUMENT_6_4_27b | Mike |
| 2000-01-01 | simplify checks for enabled switchable_zout | Mike |
| 2000-01-01 | misc fixes to max zout checksINSTRUMENT_6_4_27 | Mike |
| 2000-01-01 | Do not switch polarity relay line in dual-chan dual-pol units, if CH2 ignores... | Mike |
| 2000-01-01 | Major reworking. Set_VI_Control now stores its calculation results for later ...INSTRUMENT_6_4_23d | Mike |
| 2000-01-01 | fully implement disable timing cal percentage check | Mike |
| 2000-01-01 | debug messages showing XTR line changesINSTRUMENT_6_4_23c | Mike |
| 2000-01-01 | remove broken CH2 TTL/ECL logic code, not used in any instruments now | Mike |
| 2000-01-01 | +/- button not working as expected first press after turn-on, fixed. Better d... | Mike |
| 2000-01-01 | Allow CH2 DLY to control trigger PW (for -2CHX). Better debug messages.INSTRUMENT_6_4_23b | Mike |
| 2000-01-01 | Dump valid points to console when querying range info, to debug errant cal po... | Mike |
| 2000-01-01 | add ability to temporarily disable timing cal percentage check, for burst/sep... | Mike |
| 2000-01-01 | Only ignore polarity when shown to user. Use polarity when considering calibr... | Mike |
| 2000-01-01 | let rise time go to the lowest hardware-possible value, not just the specifie...INSTRUMENT_6_4_19c | Mike |
| 2000-01-01 | same as last, missed a spotINSTRUMENT_6_4_19b | Mike |
| 2000-01-01 | ignore tiniest encoder steps | Mike |
| 2020-03-18 | add an "ALIVE" output, to switch on VCC2 in AVRQ (for example) | Michael J. Chudobiak |
| 2000-01-01 | do not reset state before calibrating rise time in AVRQ | Mike |
| 2000-01-01 | fix min/max ampl/vout balancing when nulling delay shift calINSTRUMENT_6_4_10b | Mike |
| 2000-01-01 | fix ampl min/max checks when max_ampl is limited by max_vout (some -OT units) | Mike |
| 2000-01-01 | make force_output_fully_off work properly for 2-channel unitsINSTRUMENT_6_4_07b | Mike |
| 2000-01-01 | implement full control of DACs 8-15 | Mike |
| 2000-01-01 | Allow up to 16 DACs, by adding PCB 313A | Mike |
| 2000-01-01 | make drive polarity of zout relay configurable for -R50 units and PCB 308AINSTRUMENT_6_4_03b | Mike |
| 2018-05-03 | Removed missed hard-coded range sizesINSTRUMENT_6_4_00b | Michael J. Chudobiak |
| 2018-05-03 | use new variables and range sizes (but not initialized correctly yet) | Michael J. Chudobiak |
| 2018-05-03 | original number of points in each range was 10 | Michael J. Chudobiak |
| 2000-01-01 | Add commands to add EA distort voltages based on existing ampl cal points | Mike |
| 2000-01-01 | First attempt at handling pwl_distort automatically when adding ampl cal points | Mike |
| 2000-01-01 | Longer gate reset time before cal interval. Needed for highest delays? | Mike |
| 2000-01-01 | separate minimum equiv offset from ampl, for AVIR-4-B-OT | Mike |
| 2000-01-01 | int func should be void | Mike |
| 2000-01-01 | better abstraction of method of switching voltage-controlled PW range, for cl... | Mike |
| 2000-01-01 | better limits on freq/pw for large burst sep calibration | Mike |
| 2017-10-05 | renamed some variables in cal_add for clarity | Michael J. Chudobiak |
| 2017-10-05 | auto-handle the EA V1 distort data when deleting an ampl cal point | root |
| 2017-10-05 | rename variables in cal_del for clarity | Michael J. Chudobiak |
| 2017-10-05 | set aux word when setting nominal amplitude, for EA V1INSTRUMENT_6_2_28b | Michael J. Chudobiak |
| 2000-01-01 | implement ampl-dependent arbitrary voltage output - for AVR-E5-B S/N 13618 | Mike |
| 2000-01-01 | Rename piece-wise-linear variables for clarity, dropping reference to obsolet... | Mike |
| 2000-01-01 | replace pol_norm and pol_complement with NO/YES for clarity | Mike |
