| Age | Commit message (Expand) | Author |
|---|
| 2000-01-01 | first attempt at adding lower duty limit when ZOUT=MAX, for -LV option | Mike |
| 2020-07-27 | add support for new jig pin on keypad 104G | Michael J. Chudobiak |
| 2000-01-01 | reduce min rise time cal points to reflect faster 266D | Mike |
| 2019-01-08 | always enable vxi now | Michael J. Chudobiak |
| 2018-11-23 | enable VXI on unprogrammed boards, for testing without GPIB | Michael J. Chudobiak |
| 2000-01-01 | make max step size deviation configurableINSTRUMENT_6_4_08b | Mike |
| 2000-01-01 | added hvps_avg_curr_limit for AVR-8F-B | Mike |
| 2000-01-01 | add cap_for_pw_rc_limit for AVR-8F-B | Mike |
| 2000-01-01 | make drive polarity of zout relay configurable for -R50 units and PCB 308AINSTRUMENT_6_4_03b | Mike |
| 2018-05-03 | Use correct range size in flash init. Old unused vars not initialized any more. | Michael J. Chudobiak |
| 2018-05-03 | use new variables and range sizes (but not initialized correctly yet) | Michael J. Chudobiak |
| 2018-05-03 | original number of points in each range was 10 | Michael J. Chudobiak |
| 2000-01-01 | First attempt at handling pwl_distort automatically when adding ampl cal points | Mike |
| 2000-01-01 | make all aux error messages configurableINSTRUMENT_6_2_36c | Mike |
| 2000-01-01 | separate minimum equiv offset from ampl, for AVIR-4-B-OT | Mike |
| 2000-01-01 | remove one cal point from bottom PRF range | Mike |
| 2000-01-01 | enforce double pulse minimum spacingINSTRUMENT_6_2_30b | Mike |
| 2000-01-01 | store distortion dac values, not floats | Mike |
| 2000-01-01 | added variables for ampl-dependent distortion output | Mike |
| 2000-01-01 | Rename piece-wise-linear variables for clarity, dropping reference to obsolet... | Mike |
| 2000-01-01 | replace pol_norm and pol_complement with NO/YES for clarity | Mike |
| 2000-01-01 | rename "polarity" variables to "inverted" for clarity | Mike |
| 2000-01-01 | added a 100 ns minimum dead time requirement | Mike |
| 2000-01-01 | more specific errors during cal min/max check, and more initial cal points | Mike |
| 2000-01-01 | make self-cal min count configurable | mjc |
| 2000-01-01 | make self-cal reference frequency configurable | Mike |
| 2000-01-01 | added ability to increase output-on delay | Mike |
| 2016-12-12 | Revert force-output-on during timing cal option. Too complex, little reward. | Michael J. Chudobiak |
| 1970-01-01 | allow option to force output on during timing cal | root |
| 2000-01-01 | Additional PRF points for 0.1 Hz operation | mjc |
| 2000-01-01 | version bumpINSTRUMENT_6_2_17 | root |
| 2000-01-01 | fixed incorrect init of burst, prf integers | root |
| 2000-01-01 | choose initial PW cal points assuming DDU #2 removed | root |
| 2000-01-01 | fix last patch | root |
| 2016-09-09 | additional initial cal point per range for burst mode | Michael J. Chudobiak |
| 1970-01-01 | add PW distortion for AVR-E, AVIR, AVL. 0% at max amplitude, 100% below set v...INSTRUMENT_6_2_11b | root |
| 1970-01-01 | added volt_ctrl_delay, for 2CHPP on CH2 | root |
| 1970-01-01 | added support for sequential vs binary attenuator stages | root |
| 2016-04-06 | add toggle_trig_at_boot for IL710 initialization | Michael J. Chudobiak |
| 1970-01-01 | show FW version and controller type (BB or OL) at startupINSTRUMENT_6_2_03 | root |
| 1970-01-01 | add mutex around remounting, and add debug messagesINSTRUMENT_6_2_02 | root |
| 2000-01-01 | remount root mount without hard-coded partition name | root |
| 1970-01-01 | fix rs232 and flash initialization | root |
| 1970-01-01 | file root normally read-only now, for safe power-off. Major OS changes too.INSTRUMENT_6_2_00 | root |
| 1970-01-01 | first attempt at adding min/max-only rise time, for -KTA-TRA | root |
| 1970-01-01 | add support for double-external-trigger mode in KMPF | root |
| 1970-01-01 | allow amplitude to be in a limited negative-only range (AVR-CD2-B) | root |
| 1970-01-01 | Allow 64-char model numbersINSTRUMENT_6_0_10 | root |
| 2014-10-23 | AVR-D4-B mods: if min+max ampl both positive, do not reset to zero | Michael J. Chudobiak |
| 2014-08-26 | Do not reset fix_pw_dac_val defaults until unit is fully programmed | Michael J. Chudobiak |
