* Add support for ymodem protocol download

  Patch by Stefano Babic, 29 Mar 2006

* Memory Map Update for Delta board: U-Boot is at 0x80000000-0x84000000

Merge with /home/mk/8-benq/u-boot

10 files changed, 1198 insertions, 38 deletions

diff --git a/CHANGELOG b/CHANGELOG
index a1b52502ab..fdb6aae5e5 100644
--- a/CHANGELOG
+++ b/CHANGELOG
@@ -2,6 +2,12 @@
 Changes since U-Boot 1.1.4:
 ======================================================================
 
+* Add support for ymodem protocol download
+  Patch by Stefano Babic, 29 Mar 2006
+
+* Memory Map Update for Delta board: U-Boot is at 0x80000000-0x84000000
+  Merge from Markus Klotzbücher's repo, 01 Apr 2006
+
 * GCC-4.x fixes: clean up global data pointer initialization for all
   boards
 
diff --git a/board/delta/config.mk b/board/delta/config.mk
index 9564625478..c72e956524 100644
--- a/board/delta/config.mk
+++ b/board/delta/config.mk
@@ -2,7 +2,7 @@
 #TEXT_BASE = 0xa1700000
 #TEXT_BASE = 0xa3080000
 #TEXT_BASE = 0x9ffe0000
-TEXT_BASE = 0xa3008000
+TEXT_BASE = 0x83008000
 
 # Compile the new NAND code (needed iff #ifdef CONFIG_NEW_NAND_CODE)
 BOARDLIBS = drivers/nand/libnand.a
diff --git a/board/delta/delta.c b/board/delta/delta.c
index 2b72386742..b7671dd3b7 100644
--- a/board/delta/delta.c
+++ b/board/delta/delta.c
@@ -77,40 +77,56 @@ int dram_init (void)
 	return 0;
 }
 
-/* initialize the DA9030 Power Controller */
-static void init_DA9030()
+void i2c_init_board()
 {
-	uchar addr = (uchar) DA9030_I2C_ADDR, val = 0;
+	CKENB |= (CKENB_4_I2C);
 
 	/* setup I2C GPIO's */
 	GPIO32 = 0x801;		/* SCL = Alt. Fkt. 1 */
 	GPIO33 = 0x801;		/* SDA = Alt. Fkt. 1 */
+}
 
-	/* rising Edge on EXTON */
-	GPIO17 = 0x8800;
-	udelay(5);
-	GPIO17 = 0xc800;
-	udelay(100000);		/* wait for DA9030 */
+/* initialize the DA9030 Power Controller */
+static void init_DA9030()
+{
+	uchar addr = (uchar) DA9030_I2C_ADDR, val = 0;
+
+	CKENB |= CKENB_7_GPIO;
+	udelay(100);
+
+	/* Rising Edge on EXTON to reset DA9030 */
+	GPIO17 = 0x8800;	/* configure GPIO17, no pullup, -down */
+	GPDR0 |= (1<<17);	/* GPIO17 is output */
+	GSDR0 = (1<<17);
+	GPCR0 = (1<<17);	/* drive GPIO17 low */
+	GPSR0 = (1<<17);	/* drive GPIO17 high */
+
+#if CFG_DA9030_EXTON_DELAY
+	udelay((unsigned long) CFG_DA9030_EXTON_DELAY);	/* wait for DA9030 */
+#endif
+	GPCR0 = (1<<17);	/* drive GPIO17 low */
 
 	/* reset the watchdog and go active (0xec) */
 	val = (SYS_CONTROL_A_HWRES_ENABLE |
 	       (0x6<<4) |
 	       SYS_CONTROL_A_WDOG_ACTION |
 	       SYS_CONTROL_A_WATCHDOG);
-
-	i2c_reg_write(addr, SYS_CONTROL_A, val);
+	if(i2c_write(addr, SYS_CONTROL_A, 1, &val, 1)) {
+		printf("Error accessing DA9030 via i2c.\n");
+		return;
+	}
 
 	i2c_reg_write(addr, REG_CONTROL_1_97, 0xfd); /* disable LDO1, enable LDO6 */
 	i2c_reg_write(addr, LDO2_3, 0xd1);	/* LDO2 =1,9V, LDO3=3,1V */
 	i2c_reg_write(addr, LDO4_5, 0xcc);	/* LDO2 =1,9V, LDO3=3,1V */
-	i2c_reg_write(addr, LDO6_SIMCP, 0x3e); 	/* LDO6=3,2V, SIMCP = 5V support */
+	i2c_reg_write(addr, LDO6_SIMCP, 0x3e);	/* LDO6=3,2V, SIMCP = 5V support */
 	i2c_reg_write(addr, LDO7_8, 0xc9);	/* LDO7=2,7V, LDO8=3,0V */
 	i2c_reg_write(addr, LDO9_12, 0xec);	/* LDO9=3,0V, LDO12=3,2V */
-	i2c_reg_write(addr, BUCK, 0x0c); 	/* Buck=1.2V */
+	i2c_reg_write(addr, BUCK, 0x0c);	/* Buck=1.2V */
 	i2c_reg_write(addr, REG_CONTROL_2_98, 0x7f); /* All LDO'S on 8,9,10,11,12,14 */
-	i2c_reg_write(addr, LDO_10_11, 0xcc); 	/* LDO10=3.0V  LDO11=3.0V */
+	i2c_reg_write(addr, LDO_10_11, 0xcc);	/* LDO10=3.0V  LDO11=3.0V */
 	i2c_reg_write(addr, LDO_15, 0xae);	/* LDO15=1.8V, dislock first 3bit */
-	i2c_reg_write(addr, LDO_14_16, 0x05); 	/* LDO14=2.8V, LDO16=NB */
+	i2c_reg_write(addr, LDO_14_16, 0x05);	/* LDO14=2.8V, LDO16=NB */
 	i2c_reg_write(addr, LDO_18_19, 0x9c);	/* LDO18=3.0V, LDO19=2.7V */
 	i2c_reg_write(addr, LDO_17_SIMCP0, 0x2c); /* LDO17=3.0V, SIMCP=3V support */
 	i2c_reg_write(addr, BUCK2_DVC1, 0x9a);	/* Buck2=1.5V plus Update support of 520 MHz */
diff --git a/common/Makefile b/common/Makefile
index 7dbf84a555..eb0b5dadfe 100644
--- a/common/Makefile
+++ b/common/Makefile
@@ -51,7 +51,7 @@ COBJS	= main.o ACEX1K.o altera.o bedbug.o circbuf.o \
 	  memsize.o miiphybb.o miiphyutil.o \
 	  s_record.o serial.o soft_i2c.o soft_spi.o spartan2.o spartan3.o \
 	  usb.o usb_kbd.o usb_storage.o \
-	  virtex2.o xilinx.o
+	  virtex2.o xilinx.o crc16.o xyzModem.o
 
 OBJS	= $(AOBJS) $(COBJS)
 
diff --git a/common/cmd_load.c b/common/cmd_load.c
index b18709a47f..31fef8151b 100644
--- a/common/cmd_load.c
+++ b/common/cmd_load.c
@@ -29,11 +29,13 @@
 #include <s_record.h>
 #include <net.h>
 #include <exports.h>
+#include <xyzModem.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
 #if (CONFIG_COMMANDS & CFG_CMD_LOADS)
 static ulong load_serial (ulong offset);
+static ulong load_serial_ymodem (ulong offset);
 static int read_record (char *buf, ulong len);
 # if (CONFIG_COMMANDS & CFG_CMD_SAVES)
 static int save_serial (ulong offset, ulong size);
@@ -471,21 +473,31 @@ int do_load_serial_bin (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 		}
 	}
 
-	printf ("## Ready for binary (kermit) download "
-		"to 0x%08lX at %d bps...\n",
-		offset,
-		load_baudrate);
-	addr = load_serial_bin (offset);
+	if (strcmp(argv[0],"loady")==0) {
+		printf ("## Ready for binary (ymodem) download "
+			"to 0x%08lX at %d bps...\n",
+			offset,
+			load_baudrate);
+
+		addr = load_serial_ymodem (offset);
 
-	if (addr == ~0) {
-		load_addr = 0;
-		printf ("## Binary (kermit) download aborted\n");
-		rcode = 1;
 	} else {
-		printf ("## Start Addr      = 0x%08lX\n", addr);
-		load_addr = addr;
-	}
 
+		printf ("## Ready for binary (kermit) download "
+			"to 0x%08lX at %d bps...\n",
+			offset,
+			load_baudrate);
+		addr = load_serial_bin (offset);
+
+		if (addr == ~0) {
+			load_addr = 0;
+			printf ("## Binary (kermit) download aborted\n");
+			rcode = 1;
+		} else {
+			printf ("## Start Addr      = 0x%08lX\n", addr);
+			load_addr = addr;
+		}
+	}
 	if (load_baudrate != current_baudrate) {
 		printf ("## Switch baudrate to %d bps and press ESC ...\n",
 			current_baudrate);
@@ -959,6 +971,66 @@ START:
 	}
 	return ((ulong) os_data_addr - (ulong) bin_start_address);
 }
+
+static int getcxmodem(void) {
+	if (tstc()) 
+		return (getc());
+	return -1;
+}
+static ulong load_serial_ymodem (ulong offset)
+{
+	int size;
+	char buf[32];
+	int err;
+	int res;
+	connection_info_t info;
+	char 	ymodemBuf[1024];
+	ulong	store_addr = ~0;
+	ulong	addr = 0;
+
+	size=0;	
+	info.mode=xyzModem_ymodem;
+	res=xyzModem_stream_open(&info, &err);
+	if (!res) {
+	   
+	   while ((res=xyzModem_stream_read(ymodemBuf, 1024, &err)) > 0 ){
+		    store_addr = addr + offset;
+		    size+=res;
+		    addr+=res; 
+#ifndef CFG_NO_FLASH
+		    if (addr2info(store_addr)) {
+			int rc;
+
+			rc = flash_write((char *)ymodemBuf,store_addr,res);
+			if (rc != 0) {
+				flash_perror (rc);
+				return (~0);
+			}
+		    } else
+#endif
+		    {
+			memcpy ((char *)(store_addr), ymodemBuf, res);
+		    }
+	
+	   }
+	} 
+	else {
+		printf ("%s\n",xyzModem_error(err));
+	}
+	
+	xyzModem_stream_close(&err);
+  	xyzModem_stream_terminate(false,&getcxmodem);	
+
+
+	flush_cache (offset, size);
+
+	printf("## Total Size      = 0x%08x = %d Bytes\n", size, size);
+	sprintf(buf, "%X", size);
+	setenv("filesize", buf);
+
+	return offset;
+}
+
 #endif	/* CFG_CMD_LOADB */
 
 /* -------------------------------------------------------------------- */
@@ -1018,6 +1090,14 @@ U_BOOT_CMD(
 	" with offset 'off' and baudrate 'baud'\n"
 );
 
+U_BOOT_CMD(
+	loady, 3, 0,	do_load_serial_bin,
+	"loady   - load binary file over serial line (ymodem mode)\n",
+	"[ off ] [ baud ]\n"
+	"    - load binary file over serial line"
+	" with offset 'off' and baudrate 'baud'\n"
+);
+
 #endif	/* CFG_CMD_LOADB */
 
 /* -------------------------------------------------------------------- */
diff --git a/common/crc16.c b/common/crc16.c
new file mode 100644
index 0000000000..d571405179
--- /dev/null
+++ b/common/crc16.c
@@ -0,0 +1,106 @@
+//==========================================================================
+//
+//      crc16.c
+//
+//      16 bit CRC with polynomial x^16+x^12+x^5+1
+//
+//==========================================================================
+//####ECOSGPLCOPYRIGHTBEGIN####
+// -------------------------------------------
+// This file is part of eCos, the Embedded Configurable Operating System.
+// Copyright (C) 1998, 1999, 2000, 2001, 2002 Red Hat, Inc.
+// Copyright (C) 2002 Gary Thomas
+//
+// eCos is free software; you can redistribute it and/or modify it under
+// the terms of the GNU General Public License as published by the Free
+// Software Foundation; either version 2 or (at your option) any later version.
+//
+// eCos is distributed in the hope that it will be useful, but WITHOUT ANY
+// WARRANTY; without even the implied warranty of MERCHANTABILITY or
+// FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License
+// for more details.
+//
+// You should have received a copy of the GNU General Public License along
+// with eCos; if not, write to the Free Software Foundation, Inc.,
+// 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA.
+//
+// As a special exception, if other files instantiate templates or use macros
+// or inline functions from this file, or you compile this file and link it
+// with other works to produce a work based on this file, this file does not
+// by itself cause the resulting work to be covered by the GNU General Public
+// License. However the source code for this file must still be made available
+// in accordance with section (3) of the GNU General Public License.
+//
+// This exception does not invalidate any other reasons why a work based on
+// this file might be covered by the GNU General Public License.
+//
+// Alternative licenses for eCos may be arranged by contacting Red Hat, Inc.
+// at http://sources.redhat.com/ecos/ecos-license/
+// -------------------------------------------
+//####ECOSGPLCOPYRIGHTEND####
+//==========================================================================
+//#####DESCRIPTIONBEGIN####
+//
+// Author(s):    gthomas
+// Contributors: gthomas,asl
+// Date:         2001-01-31
+// Purpose:      
+// Description:  
+//              
+// This code is part of eCos (tm).
+//
+//####DESCRIPTIONEND####
+//
+//==========================================================================
+
+#include "crc.h"
+
+// Table of CRC constants - implements x^16+x^12+x^5+1
+static const uint16_t crc16_tab[] = {
+    0x0000, 0x1021, 0x2042, 0x3063, 0x4084, 0x50a5, 0x60c6, 0x70e7, 
+    0x8108, 0x9129, 0xa14a, 0xb16b, 0xc18c, 0xd1ad, 0xe1ce, 0xf1ef, 
+    0x1231, 0x0210, 0x3273, 0x2252, 0x52b5, 0x4294, 0x72f7, 0x62d6, 
+    0x9339, 0x8318, 0xb37b, 0xa35a, 0xd3bd, 0xc39c, 0xf3ff, 0xe3de, 
+    0x2462, 0x3443, 0x0420, 0x1401, 0x64e6, 0x74c7, 0x44a4, 0x5485, 
+    0xa56a, 0xb54b, 0x8528, 0x9509, 0xe5ee, 0xf5cf, 0xc5ac, 0xd58d, 
+    0x3653, 0x2672, 0x1611, 0x0630, 0x76d7, 0x66f6, 0x5695, 0x46b4, 
+    0xb75b, 0xa77a, 0x9719, 0x8738, 0xf7df, 0xe7fe, 0xd79d, 0xc7bc, 
+    0x48c4, 0x58e5, 0x6886, 0x78a7, 0x0840, 0x1861, 0x2802, 0x3823, 
+    0xc9cc, 0xd9ed, 0xe98e, 0xf9af, 0x8948, 0x9969, 0xa90a, 0xb92b, 
+    0x5af5, 0x4ad4, 0x7ab7, 0x6a96, 0x1a71, 0x0a50, 0x3a33, 0x2a12, 
+    0xdbfd, 0xcbdc, 0xfbbf, 0xeb9e, 0x9b79, 0x8b58, 0xbb3b, 0xab1a, 
+    0x6ca6, 0x7c87, 0x4ce4, 0x5cc5, 0x2c22, 0x3c03, 0x0c60, 0x1c41, 
+    0xedae, 0xfd8f, 0xcdec, 0xddcd, 0xad2a, 0xbd0b, 0x8d68, 0x9d49, 
+    0x7e97, 0x6eb6, 0x5ed5, 0x4ef4, 0x3e13, 0x2e32, 0x1e51, 0x0e70, 
+    0xff9f, 0xefbe, 0xdfdd, 0xcffc, 0xbf1b, 0xaf3a, 0x9f59, 0x8f78, 
+    0x9188, 0x81a9, 0xb1ca, 0xa1eb, 0xd10c, 0xc12d, 0xf14e, 0xe16f, 
+    0x1080, 0x00a1, 0x30c2, 0x20e3, 0x5004, 0x4025, 0x7046, 0x6067, 
+    0x83b9, 0x9398, 0xa3fb, 0xb3da, 0xc33d, 0xd31c, 0xe37f, 0xf35e, 
+    0x02b1, 0x1290, 0x22f3, 0x32d2, 0x4235, 0x5214, 0x6277, 0x7256, 
+    0xb5ea, 0xa5cb, 0x95a8, 0x8589, 0xf56e, 0xe54f, 0xd52c, 0xc50d, 
+    0x34e2, 0x24c3, 0x14a0, 0x0481, 0x7466, 0x6447, 0x5424, 0x4405, 
+    0xa7db, 0xb7fa, 0x8799, 0x97b8, 0xe75f, 0xf77e, 0xc71d, 0xd73c, 
+    0x26d3, 0x36f2, 0x0691, 0x16b0, 0x6657, 0x7676, 0x4615, 0x5634, 
+    0xd94c, 0xc96d, 0xf90e, 0xe92f, 0x99c8, 0x89e9, 0xb98a, 0xa9ab, 
+    0x5844, 0x4865, 0x7806, 0x6827, 0x18c0, 0x08e1, 0x3882, 0x28a3, 
+    0xcb7d, 0xdb5c, 0xeb3f, 0xfb1e, 0x8bf9, 0x9bd8, 0xabbb, 0xbb9a, 
+    0x4a75, 0x5a54, 0x6a37, 0x7a16, 0x0af1, 0x1ad0, 0x2ab3, 0x3a92, 
+    0xfd2e, 0xed0f, 0xdd6c, 0xcd4d, 0xbdaa, 0xad8b, 0x9de8, 0x8dc9, 
+    0x7c26, 0x6c07, 0x5c64, 0x4c45, 0x3ca2, 0x2c83, 0x1ce0, 0x0cc1, 
+    0xef1f, 0xff3e, 0xcf5d, 0xdf7c, 0xaf9b, 0xbfba, 0x8fd9, 0x9ff8, 
+    0x6e17, 0x7e36, 0x4e55, 0x5e74, 0x2e93, 0x3eb2, 0x0ed1, 0x1ef0, 
+};
+
+uint16_t
+cyg_crc16(unsigned char *buf, int len)
+{
+    int i;
+    uint16_t cksum;
+
+    cksum = 0;
+    for (i = 0;  i < len;  i++) {
+        cksum = crc16_tab[((cksum>>8) ^ *buf++) & 0xFF] ^ (cksum << 8);
+    }
+    return cksum;
+}
+
diff --git a/common/xyzModem.c b/common/xyzModem.c
new file mode 100644
index 0000000000..3c86b138b3
--- /dev/null
+++ b/common/xyzModem.c
@@ -0,0 +1,739 @@
+//==========================================================================
+//
+//      xyzModem.c
+//
+//      RedBoot stream handler for xyzModem protocol
+//
+//==========================================================================
+//####ECOSGPLCOPYRIGHTBEGIN####
+// -------------------------------------------
+// This file is part of eCos, the Embedded Configurable Operating System.
+// Copyright (C) 1998, 1999, 2000, 2001, 2002 Red Hat, Inc.
+// Copyright (C) 2002 Gary Thomas
+//
+// eCos is free software; you can redistribute it and/or modify it under
+// the terms of the GNU General Public License as published by the Free
+// Software Foundation; either version 2 or (at your option) any later version.
+//
+// eCos is distributed in the hope that it will be useful, but WITHOUT ANY
+// WARRANTY; without even the implied warranty of MERCHANTABILITY or
+// FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License
+// for more details.
+//
+// You should have received a copy of the GNU General Public License along
+// with eCos; if not, write to the Free Software Foundation, Inc.,
+// 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA.
+//
+// As a special exception, if other files instantiate templates or use macros
+// or inline functions from this file, or you compile this file and link it
+// with other works to produce a work based on this file, this file does not
+// by itself cause the resulting work to be covered by the GNU General Public
+// License. However the source code for this file must still be made available
+// in accordance with section (3) of the GNU General Public License.
+//
+// This exception does not invalidate any other reasons why a work based on
+// this file might be covered by the GNU General Public License.
+//
+// Alternative licenses for eCos may be arranged by contacting Red Hat, Inc.
+// at http://sources.redhat.com/ecos/ecos-license/
+// -------------------------------------------
+//####ECOSGPLCOPYRIGHTEND####
+//==========================================================================
+//#####DESCRIPTIONBEGIN####
+//
+// Author(s):    gthomas
+// Contributors: gthomas, tsmith, Yoshinori Sato
+// Date:         2000-07-14
+// Purpose:      
+// Description:  
+//              
+// This code is part of RedBoot (tm).
+//
+//####DESCRIPTIONEND####
+//
+//==========================================================================
+#include <common.h>
+#include <xyzModem.h>
+#include <stdarg.h>
+#include <crc.h>
+
+// Assumption - run xyzModem protocol over the console port
+
+// Values magic to the protocol
+#define SOH 0x01
+#define STX 0x02
+#define EOT 0x04
+#define ACK 0x06
+#define BSP 0x08
+#define NAK 0x15
+#define CAN 0x18
+#define EOF 0x1A  // ^Z for DOS officionados
+
+#define USE_YMODEM_LENGTH
+
+// Data & state local to the protocol
+static struct {
+#ifdef REDBOOT
+    hal_virtual_comm_table_t* __chan;
+#else
+    int *__chan;
+#endif
+    unsigned char pkt[1024], *bufp;
+    unsigned char blk,cblk,crc1,crc2;
+    unsigned char next_blk;  // Expected block
+    int len, mode, total_retries;
+    int total_SOH, total_STX, total_CAN;
+    bool crc_mode, at_eof, tx_ack;
+#ifdef USE_YMODEM_LENGTH
+    unsigned long file_length, read_length;
+#endif
+} xyz;
+
+#define xyzModem_CHAR_TIMEOUT            2000  // 2 seconds
+#define xyzModem_MAX_RETRIES             20
+#define xyzModem_MAX_RETRIES_WITH_CRC    10
+#define xyzModem_CAN_COUNT                3    // Wait for 3 CAN before quitting
+
+
+#ifndef REDBOOT  //SB
+typedef int cyg_int32;
+int CYGACC_COMM_IF_GETC_TIMEOUT (char chan,char *c) {
+#define DELAY 20
+	unsigned long counter=0;
+	while (!tstc() && (counter < xyzModem_CHAR_TIMEOUT*1000/DELAY)) {
+		udelay(DELAY);
+		counter++;
+	}
+	if (tstc()) {
+		*c=getc();
+		return 1;
+	}
+	return 0;
+}
+
+void CYGACC_COMM_IF_PUTC(char x,char y) {
+	putc(y);
+}
+
+// Validate a hex character
+__inline__ static bool
+_is_hex(char c)
+{
+    return (((c >= '0') && (c <= '9')) ||
+            ((c >= 'A') && (c <= 'F')) ||
+            ((c >= 'a') && (c <= 'f')));
+}
+
+// Convert a single hex nibble
+__inline__ static int
+_from_hex(char c)
+{
+    int ret = 0;
+
+    if ((c >= '0') && (c <= '9')) {
+        ret = (c - '0');
+    } else if ((c >= 'a') && (c <= 'f')) {
+        ret = (c - 'a' + 0x0a);
+    } else if ((c >= 'A') && (c <= 'F')) {
+        ret = (c - 'A' + 0x0A);
+    }
+    return ret;
+}
+
+// Convert a character to lower case
+__inline__ static char
+_tolower(char c)
+{
+    if ((c >= 'A') && (c <= 'Z')) {
+        c = (c - 'A') + 'a';
+    }
+    return c;
+}
+
+
+
+//
+// Parse (scan) a number
+//
+bool
+parse_num(char *s, unsigned long *val, char **es, char *delim)
+{
+    bool first = true;
+    int radix = 10;
+    char c;
+    unsigned long result = 0;
+    int digit;
+
+    while (*s == ' ') s++;
+    while (*s) {
+        if (first && (s[0] == '0') && (_tolower(s[1]) == 'x')) {
+            radix = 16;
+            s += 2;
+        }
+        first = false;
+        c = *s++;
+        if (_is_hex(c) && ((digit = _from_hex(c)) < radix)) {
+            // Valid digit
+#ifdef CYGPKG_HAL_MIPS
+            // FIXME: tx49 compiler generates 0x2539018 for MUL which
+            // isn't any good.
+            if (16 == radix)
+                result = result << 4;
+            else
+                result = 10 * result;
+            result += digit;
+#else
+            result = (result * radix) + digit;
+#endif
+        } else {
+            if (delim != (char *)0) {
+                // See if this character is one of the delimiters
+                char *dp = delim;
+                while (*dp && (c != *dp)) dp++;
+                if (*dp) break;  // Found a good delimiter
+            }
+            return false;  // Malformatted number
+        }
+    }
+    *val = result;
+    if (es != (char **)0) {
+        *es = s;
+    }
+    return true;
+}
+
+#endif
+
+#define USE_SPRINTF
+#ifdef DEBUG
+#ifndef USE_SPRINTF
+//
+// Note: this debug setup only works if the target platform has two serial ports
+// available so that the other one (currently only port 1) can be used for debug
+// messages.
+//
+static int
+zm_dprintf(char *fmt, ...)
+{
+    int cur_console;
+    va_list args;
+
+    va_start(args, fmt);
+#ifdef REDBOOT
+    cur_console = CYGACC_CALL_IF_SET_CONSOLE_COMM(CYGNUM_CALL_IF_SET_COMM_ID_QUERY_CURRENT);
+    CYGACC_CALL_IF_SET_CONSOLE_COMM(1);
+#endif
+    diag_vprintf(fmt, args);
+#ifdef REDBOOT
+    CYGACC_CALL_IF_SET_CONSOLE_COMM(cur_console);
+#endif
+}
+
+static void
+zm_flush(void)
+{
+}
+
+#else
+//
+// Note: this debug setup works by storing the strings in a fixed buffer
+//
+#define FINAL
+#ifdef FINAL
+static char *zm_out = (char *)0x00380000;
+static char *zm_out_start = (char *)0x00380000;
+#else
+static char zm_buf[8192];
+static char *zm_out=zm_buf;
+static char *zm_out_start = zm_buf;
+
+#endif
+static int
+zm_dprintf(char *fmt, ...)
+{
+    int len;
+    va_list args;
+
+    va_start(args, fmt);
+    len = diag_vsprintf(zm_out, fmt, args);
+    zm_out += len;
+    return len;
+}
+
+static void
+zm_flush(void)
+{
+    char *p = zm_out_start;
+#ifdef REDBOOT
+    while (*p) mon_write_char(*p++);
+#endif
+    zm_out = zm_out_start;
+}
+#endif
+
+static void
+zm_dump_buf(void *buf, int len)
+{
+#ifdef REDBOOT
+    diag_vdump_buf_with_offset(zm_dprintf, buf, len, 0);
+#else
+
+#endif
+}
+
+static unsigned char zm_buf[2048];
+static unsigned char *zm_bp;
+
+static void
+zm_new(void)
+{
+    zm_bp = zm_buf;
+}
+
+static void
+zm_save(unsigned char c)
+{
+    *zm_bp++ = c;
+}
+
+static void
+zm_dump(int line)
+{
+    zm_dprintf("Packet at line: %d\n", line);
+    zm_dump_buf(zm_buf, zm_bp-zm_buf);
+}
+
+#define ZM_DEBUG(x) x
+#else
+#define ZM_DEBUG(x)
+#endif
+
+// Wait for the line to go idle
+static void
+xyzModem_flush(void)
+{
+    int res;
+    char c;
+    while (true) {
+        res = CYGACC_COMM_IF_GETC_TIMEOUT(*xyz.__chan, &c);
+        if (!res) return;
+    }
+}
+
+static int
+xyzModem_get_hdr(void)
+{
+    char c;
+    int res;
+    bool hdr_found = false;
+    int i, can_total, hdr_chars;
+    unsigned short cksum;
+
+    ZM_DEBUG(zm_new());
+    // Find the start of a header
+    can_total = 0;
+    hdr_chars = 0;
+
+    if (xyz.tx_ack) {
+        CYGACC_COMM_IF_PUTC(*xyz.__chan, ACK);
+        xyz.tx_ack = false;
+    }
+    while (!hdr_found) {
+        res = CYGACC_COMM_IF_GETC_TIMEOUT(*xyz.__chan, &c);
+        ZM_DEBUG(zm_save(c));
+        if (res) {
+            hdr_chars++;
+            switch (c) {
+            case SOH:
+                xyz.total_SOH++;
+            case STX:
+                if (c == STX) xyz.total_STX++;
+                hdr_found = true;
+                break;
+            case CAN:
+                xyz.total_CAN++;
+                ZM_DEBUG(zm_dump(__LINE__));
+                if (++can_total == xyzModem_CAN_COUNT) {
+                    return xyzModem_cancel;
+                } else {
+                    // Wait for multiple CAN to avoid early quits
+                    break;
+                }
+            case EOT:
+                // EOT only supported if no noise
+                if (hdr_chars == 1) {
+                    CYGACC_COMM_IF_PUTC(*xyz.__chan, ACK);
+                    ZM_DEBUG(zm_dprintf("ACK on EOT #%d\n", __LINE__));
+                    ZM_DEBUG(zm_dump(__LINE__));
+                    return xyzModem_eof;
+                }
+            default:
+                // Ignore, waiting for start of header
+                ;
+            }
+        } else {
+            // Data stream timed out
+            xyzModem_flush();  // Toss any current input
+            ZM_DEBUG(zm_dump(__LINE__));
+            CYGACC_CALL_IF_DELAY_US((cyg_int32)250000);
+            return xyzModem_timeout;
+        }
+    }
+
+    // Header found, now read the data
+    res = CYGACC_COMM_IF_GETC_TIMEOUT(*xyz.__chan, &xyz.blk);
+    ZM_DEBUG(zm_save(xyz.blk));
+    if (!res) {
+        ZM_DEBUG(zm_dump(__LINE__));
+        return xyzModem_timeout;
+    }
+    res = CYGACC_COMM_IF_GETC_TIMEOUT(*xyz.__chan, &xyz.cblk);
+    ZM_DEBUG(zm_save(xyz.cblk));
+    if (!res) {
+        ZM_DEBUG(zm_dump(__LINE__));
+        return xyzModem_timeout;
+    }
+    xyz.len = (c == SOH) ? 128 : 1024;
+    xyz.bufp = xyz.pkt;
+    for (i = 0;  i < xyz.len;  i++) {
+        res = CYGACC_COMM_IF_GETC_TIMEOUT(*xyz.__chan, &c);
+        ZM_DEBUG(zm_save(c));
+        if (res) {
+            xyz.pkt[i] = c;
+        } else {
+            ZM_DEBUG(zm_dump(__LINE__));
+            return xyzModem_timeout;
+        }
+    }
+    res = CYGACC_COMM_IF_GETC_TIMEOUT(*xyz.__chan, &xyz.crc1);
+    ZM_DEBUG(zm_save(xyz.crc1));
+    if (!res) {
+        ZM_DEBUG(zm_dump(__LINE__));
+        return xyzModem_timeout;
+    }
+    if (xyz.crc_mode) {
+        res = CYGACC_COMM_IF_GETC_TIMEOUT(*xyz.__chan, &xyz.crc2);
+        ZM_DEBUG(zm_save(xyz.crc2));
+        if (!res) {
+            ZM_DEBUG(zm_dump(__LINE__));
+            return xyzModem_timeout;
+        }
+    }
+    ZM_DEBUG(zm_dump(__LINE__));
+    // Validate the message
+    if ((xyz.blk ^ xyz.cblk) != (unsigned char)0xFF) {
+        ZM_DEBUG(zm_dprintf("Framing error - blk: %x/%x/%x\n", xyz.blk, xyz.cblk, (xyz.blk ^ xyz.cblk)));
+        ZM_DEBUG(zm_dump_buf(xyz.pkt, xyz.len));
+        xyzModem_flush();
+        return xyzModem_frame;
+    }
+    // Verify checksum/CRC
+    if (xyz.crc_mode) {
+        cksum = cyg_crc16(xyz.pkt, xyz.len);
+        if (cksum != ((xyz.crc1 << 8) | xyz.crc2)) {
+            ZM_DEBUG(zm_dprintf("CRC error - recvd: %02x%02x, computed: %x\n", 
+                                xyz.crc1, xyz.crc2, cksum & 0xFFFF));
+            return xyzModem_cksum;
+        }
+    } else {
+        cksum = 0;
+        for (i = 0;  i < xyz.len;  i++) {
+            cksum += xyz.pkt[i];
+        }
+        if (xyz.crc1 != (cksum & 0xFF)) {
+            ZM_DEBUG(zm_dprintf("Checksum error - recvd: %x, computed: %x\n", xyz.crc1, cksum & 0xFF));
+            return xyzModem_cksum;
+        }
+    }
+    // If we get here, the message passes [structural] muster
+    return 0;
+}
+
+int 
+xyzModem_stream_open(connection_info_t *info, int *err)
+{
+    int console_chan, stat=0;
+    int retries = xyzModem_MAX_RETRIES;
+    int crc_retries = xyzModem_MAX_RETRIES_WITH_CRC;
+
+//    ZM_DEBUG(zm_out = zm_out_start);
+#ifdef xyzModem_zmodem
+    if (info->mode == xyzModem_zmodem) {
+        *err = xyzModem_noZmodem;
+        return -1;
+    }
+#endif
+
+#ifdef REDBOOT
+    // Set up the I/O channel.  Note: this allows for using a different port in the future
+    console_chan = CYGACC_CALL_IF_SET_CONSOLE_COMM(CYGNUM_CALL_IF_SET_COMM_ID_QUERY_CURRENT);
+    if (info->chan >= 0) {
+        CYGACC_CALL_IF_SET_CONSOLE_COMM(info->chan);
+    } else {
+        CYGACC_CALL_IF_SET_CONSOLE_COMM(console_chan);
+    }
+    xyz.__chan = CYGACC_CALL_IF_CONSOLE_PROCS();
+
+    CYGACC_CALL_IF_SET_CONSOLE_COMM(console_chan);
+    CYGACC_COMM_IF_CONTROL(*xyz.__chan, __COMMCTL_SET_TIMEOUT, xyzModem_CHAR_TIMEOUT);
+#else
+// TODO: CHECK !
+    int dummy;
+    xyz.__chan=&dummy; 
+#endif
+    xyz.len = 0;
+    xyz.crc_mode = true;
+    xyz.at_eof = false;
+    xyz.tx_ack = false;
+    xyz.mode = info->mode;
+    xyz.total_retries = 0;
+    xyz.total_SOH = 0;
+    xyz.total_STX = 0;
+    xyz.total_CAN = 0;
+#ifdef USE_YMODEM_LENGTH
+    xyz.read_length = 0;
+    xyz.file_length = 0;
+#endif
+    
+    CYGACC_COMM_IF_PUTC(*xyz.__chan, (xyz.crc_mode ? 'C' : NAK));
+
+    if (xyz.mode == xyzModem_xmodem) {
+	    // X-modem doesn't have an information header - exit here
+            xyz.next_blk = 1;
+            return 0;
+    }
+
+    while (retries-- > 0) {
+        stat = xyzModem_get_hdr();
+        if (stat == 0) {
+            // Y-modem file information header
+            if (xyz.blk == 0) {
+#ifdef USE_YMODEM_LENGTH
+                // skip filename
+                while (*xyz.bufp++);
+                // get the length
+                parse_num(xyz.bufp, &xyz.file_length, NULL, " ");
+#endif
+                // The rest of the file name data block quietly discarded
+                xyz.tx_ack = true;
+            }
+            xyz.next_blk = 1;
+            xyz.len = 0;
+            return 0;
+        } else 
+        if (stat == xyzModem_timeout) {
+            if (--crc_retries <= 0) xyz.crc_mode = false;
+            CYGACC_CALL_IF_DELAY_US(5*100000);   // Extra delay for startup
+            CYGACC_COMM_IF_PUTC(*xyz.__chan, (xyz.crc_mode ? 'C' : NAK));
+            xyz.total_retries++;
+            ZM_DEBUG(zm_dprintf("NAK (%d)\n", __LINE__));
+        }
+        if (stat == xyzModem_cancel) {
+            break;
+        }
+    }
+    *err = stat;
+    ZM_DEBUG(zm_flush());
+    return -1;
+}
+
+int 
+xyzModem_stream_read(char *buf, int size, int *err)
+{
+    int stat, total, len;
+    int retries;
+
+    total = 0;
+    stat = xyzModem_cancel;
+    // Try and get 'size' bytes into the buffer
+    while (!xyz.at_eof && (size > 0)) {
+        if (xyz.len == 0) {
+            retries = xyzModem_MAX_RETRIES;
+            while (retries-- > 0) {
+                stat = xyzModem_get_hdr();
+                if (stat == 0) {
+                    if (xyz.blk == xyz.next_blk) {
+                        xyz.tx_ack = true;
+                        ZM_DEBUG(zm_dprintf("ACK block %d (%d)\n", xyz.blk, __LINE__));
+                        xyz.next_blk = (xyz.next_blk + 1) & 0xFF;
+
+#if defined(xyzModem_zmodem) || defined(USE_YMODEM_LENGTH)
+                        if (xyz.mode == xyzModem_xmodem || xyz.file_length == 0) {
+#else
+                        if (1) {
+#endif
+                            // Data blocks can be padded with ^Z (EOF) characters
+                            // This code tries to detect and remove them
+                            if ((xyz.bufp[xyz.len-1] == EOF) &&
+                                (xyz.bufp[xyz.len-2] == EOF) &&
+                                (xyz.bufp[xyz.len-3] == EOF)) {
+                                while (xyz.len && (xyz.bufp[xyz.len-1] == EOF)) {
+                                    xyz.len--;
+                                }
+                            }
+                        }
+
+#ifdef USE_YMODEM_LENGTH
+                        // See if accumulated length exceeds that of the file.
+                        // If so, reduce size (i.e., cut out pad bytes)
+                        // Only do this for Y-modem (and Z-modem should it ever
+                        // be supported since it can fall back to Y-modem mode).
+                        if (xyz.mode != xyzModem_xmodem && 0 != xyz.file_length) {
+                            xyz.read_length += xyz.len;
+                            if (xyz.read_length > xyz.file_length) {
+                                xyz.len -= (xyz.read_length - xyz.file_length);
+                            }
+                        }
+#endif
+                        break;
+                    } else if (xyz.blk == ((xyz.next_blk - 1) & 0xFF)) {
+                        // Just re-ACK this so sender will get on with it
+                        CYGACC_COMM_IF_PUTC(*xyz.__chan, ACK);
+                        continue;  // Need new header
+                    } else {
+                        stat = xyzModem_sequence;
+                    }
+                }
+                if (stat == xyzModem_cancel) {
+                    break;
+                }
+                if (stat == xyzModem_eof) {
+                    CYGACC_COMM_IF_PUTC(*xyz.__chan, ACK);
+                    ZM_DEBUG(zm_dprintf("ACK (%d)\n", __LINE__));
+                    if (xyz.mode == xyzModem_ymodem) {
+                        CYGACC_COMM_IF_PUTC(*xyz.__chan, (xyz.crc_mode ? 'C' : NAK));
+                        xyz.total_retries++;
+                        ZM_DEBUG(zm_dprintf("Reading Final Header\n"));
+                        stat = xyzModem_get_hdr();                        
+                        CYGACC_COMM_IF_PUTC(*xyz.__chan, ACK);
+                        ZM_DEBUG(zm_dprintf("FINAL ACK (%d)\n", __LINE__));
+                    }
+                    xyz.at_eof = true;
+                    break;
+                }
+                CYGACC_COMM_IF_PUTC(*xyz.__chan, (xyz.crc_mode ? 'C' : NAK));
+                xyz.total_retries++;
+                ZM_DEBUG(zm_dprintf("NAK (%d)\n", __LINE__));
+            }
+            if (stat < 0) {
+                *err = stat;
+                xyz.len = -1;
+                return total;
+            }
+        }
+        // Don't "read" data from the EOF protocol package
+        if (!xyz.at_eof) {
+            len = xyz.len;
+            if (size < len) len = size;
+            memcpy(buf, xyz.bufp, len);
+            size -= len;
+            buf += len;
+            total += len;
+            xyz.len -= len;
+            xyz.bufp += len;
+        }
+    }
+    return total;
+}
+
+void
+xyzModem_stream_close(int *err)
+{
+    diag_printf("xyzModem - %s mode, %d(SOH)/%d(STX)/%d(CAN) packets, %d retries\n", 
+                xyz.crc_mode ? "CRC" : "Cksum",
+                xyz.total_SOH, xyz.total_STX, xyz.total_CAN,
+                xyz.total_retries);
+    ZM_DEBUG(zm_flush());
+}
+
+// Need to be able to clean out the input buffer, so have to take the
+// getc
+void xyzModem_stream_terminate(bool abort, int (*getc)(void))
+{
+  int c;
+
+  if (abort) {
+      ZM_DEBUG(zm_dprintf("!!!! TRANSFER ABORT !!!!\n"));
+      switch (xyz.mode) {
+	case xyzModem_xmodem:
+	case xyzModem_ymodem:
+	  // The X/YMODEM Spec seems to suggest that multiple CAN followed by an equal
+	  // number of Backspaces is a friendly way to get the other end to abort.
+	  CYGACC_COMM_IF_PUTC(*xyz.__chan,CAN);
+	  CYGACC_COMM_IF_PUTC(*xyz.__chan,CAN);
+	  CYGACC_COMM_IF_PUTC(*xyz.__chan,CAN);
+	  CYGACC_COMM_IF_PUTC(*xyz.__chan,CAN);
+	  CYGACC_COMM_IF_PUTC(*xyz.__chan,BSP);
+	  CYGACC_COMM_IF_PUTC(*xyz.__chan,BSP);
+	  CYGACC_COMM_IF_PUTC(*xyz.__chan,BSP);
+	  CYGACC_COMM_IF_PUTC(*xyz.__chan,BSP);
+	  // Now consume the rest of what's waiting on the line.
+	  ZM_DEBUG(zm_dprintf("Flushing serial line.\n"));
+	  xyzModem_flush();
+          xyz.at_eof = true;
+	break;
+#ifdef xyzModem_zmodem
+	case xyzModem_zmodem:
+	  // Might support it some day I suppose.
+#endif
+	break;
+      }
+  } else {
+      ZM_DEBUG(zm_dprintf("Engaging cleanup mode...\n"));
+      // Consume any trailing crap left in the inbuffer from
+      // previous recieved blocks. Since very few files are an exact multiple
+      // of the transfer block size, there will almost always be some gunk here.
+      // If we don't eat it now, RedBoot will think the user typed it.
+      ZM_DEBUG(zm_dprintf("Trailing gunk:\n"));
+      while ((c = (*getc)()) > -1) ;
+      ZM_DEBUG(zm_dprintf("\n"));
+      // Make a small delay to give terminal programs like minicom
+      // time to get control again after their file transfer program
+      // exits.
+      CYGACC_CALL_IF_DELAY_US((cyg_int32)250000);
+  }
+}
+
+char *
+xyzModem_error(int err)
+{
+    switch (err) {
+    case xyzModem_access:
+        return "Can't access file";
+        break;
+    case xyzModem_noZmodem:
+        return "Sorry, zModem not available yet";
+        break;
+    case xyzModem_timeout:
+        return "Timed out";
+        break;
+    case xyzModem_eof:
+        return "End of file";
+        break;
+    case xyzModem_cancel:
+        return "Cancelled";
+        break;
+    case xyzModem_frame:
+        return "Invalid framing";
+        break;
+    case xyzModem_cksum:
+        return "CRC/checksum error";
+        break;
+    case xyzModem_sequence:
+        return "Block sequence error";
+        break;
+    default:
+        return "Unknown error";
+        break;
+    }
+}
+
+//
+// RedBoot interface
+//
+#if 0 // SB
+GETC_IO_FUNCS(xyzModem_io, xyzModem_stream_open, xyzModem_stream_close,
+              xyzModem_stream_terminate, xyzModem_stream_read, xyzModem_error);
+RedBoot_load(xmodem, xyzModem_io, false, false, xyzModem_xmodem);
+RedBoot_load(ymodem, xyzModem_io, false, false, xyzModem_ymodem);
+#endif 
diff --git a/include/configs/delta.h b/include/configs/delta.h
index 776ee15d1a..5edea95a4f 100644
--- a/include/configs/delta.h
+++ b/include/configs/delta.h
@@ -62,6 +62,8 @@
 #define CFG_I2C_SPEED		400000	/* I2C speed */
 #define CFG_I2C_SLAVE		1	/* I2C controllers address */
 #define DA9030_I2C_ADDR		0x49	/* I2C address of DA9030 */
+#define CFG_DA9030_EXTON_DELAY	100000	/* wait x us after DA9030 reset via EXTON */
+#define CFG_I2C_INIT_BOARD	1
 /* #define CONFIG_HW_WATCHDOG	1	/\* Required for hitting the DA9030 WD *\/ */
 
 /*
@@ -124,8 +126,8 @@
 #define CFG_BARGSIZE		CFG_CBSIZE	/* Boot Argument Buffer Size	*/
 #define CFG_DEVICE_NULLDEV	1
 
-#define CFG_MEMTEST_START	0xa0400000	/* memtest works on	*/
-#define CFG_MEMTEST_END		0xa0800000	/* 4 ... 8 MB in DRAM	*/
+#define CFG_MEMTEST_START	0x80400000	/* memtest works on	*/
+#define CFG_MEMTEST_END		0x80800000	/* 4 ... 8 MB in DRAM	*/
 
 #undef	CFG_CLKS_IN_HZ		/* everything, incl board info, in Hz */
 
@@ -133,9 +135,7 @@
 
 #define CFG_HZ			3250000		/* incrementer freq: 3.25 MHz */
 
-/* Monahans Core Frequency = 
- * 
- */
+/* Monahans Core Frequency */
 #define CFG_MONAHANS_RUN_MODE_OSC_RATIO		16 /* valid values: 8, 16, 24, 31 */
 #define CFG_MONAHANS_TURBO_RUN_MODE_RATIO	1  /* valid values: 1, 2 */
 
@@ -160,16 +160,16 @@
  * Physical Memory Map
  */
 #define CONFIG_NR_DRAM_BANKS	4	   /* we have 2 banks of DRAM */
-#define PHYS_SDRAM_1		0xa0000000 /* SDRAM Bank #1 */
+#define PHYS_SDRAM_1		0x80000000 /* SDRAM Bank #1 */
 #define PHYS_SDRAM_1_SIZE	0x1000000  /* 64 MB */
-#define PHYS_SDRAM_2		0xa1000000 /* SDRAM Bank #2 */
+#define PHYS_SDRAM_2		0x81000000 /* SDRAM Bank #2 */
 #define PHYS_SDRAM_2_SIZE	0x1000000  /* 64 MB */
-#define PHYS_SDRAM_3		0xa2000000 /* SDRAM Bank #3 */
+#define PHYS_SDRAM_3		0x82000000 /* SDRAM Bank #3 */
 #define PHYS_SDRAM_3_SIZE	0x1000000  /* 64 MB */
-#define PHYS_SDRAM_4		0xa3000000 /* SDRAM Bank #4 */
+#define PHYS_SDRAM_4		0x83000000 /* SDRAM Bank #4 */
 #define PHYS_SDRAM_4_SIZE	0x1000000  /* 64 MB */
 
-#define CFG_DRAM_BASE		0xa0000000 /* at CS0 */
+#define CFG_DRAM_BASE		0x80000000 /* at CS0 */
 #define CFG_DRAM_SIZE		0x04000000 /* 64 MB Ram */
 
 #undef CFG_SKIP_DRAM_SCRUB
diff --git a/include/crc.h b/include/crc.h
new file mode 100644
index 0000000000..63399bf8f6
--- /dev/null
+++ b/include/crc.h
@@ -0,0 +1,101 @@
+//==========================================================================
+//
+//      crc.h
+//
+//      Interface for the CRC algorithms.
+//
+//==========================================================================
+//####ECOSGPLCOPYRIGHTBEGIN####
+// -------------------------------------------
+// This file is part of eCos, the Embedded Configurable Operating System.
+// Copyright (C) 2002 Andrew Lunn
+//
+// eCos is free software; you can redistribute it and/or modify it under
+// the terms of the GNU General Public License as published by the Free
+// Software Foundation; either version 2 or (at your option) any later version.
+//
+// eCos is distributed in the hope that it will be useful, but WITHOUT ANY
+// WARRANTY; without even the implied warranty of MERCHANTABILITY or
+// FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License
+// for more details.
+//
+// You should have received a copy of the GNU General Public License along
+// with eCos; if not, write to the Free Software Foundation, Inc.,
+// 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA.
+//
+// As a special exception, if other files instantiate templates or use macros
+// or inline functions from this file, or you compile this file and link it
+// with other works to produce a work based on this file, this file does not
+// by itself cause the resulting work to be covered by the GNU General Public
+// License. However the source code for this file must still be made available
+// in accordance with section (3) of the GNU General Public License.
+//
+// This exception does not invalidate any other reasons why a work based on
+// this file might be covered by the GNU General Public License.
+//
+// Alternative licenses for eCos may be arranged by contacting Red Hat, Inc.
+// at http://sources.redhat.com/ecos/ecos-license/
+// -------------------------------------------
+//####ECOSGPLCOPYRIGHTEND####
+//==========================================================================
+//#####DESCRIPTIONBEGIN####
+//
+// Author(s):    Andrew Lunn
+// Contributors: Andrew Lunn
+// Date:         2002-08-06
+// Purpose:      
+// Description:  
+//              
+// This code is part of eCos (tm).
+//
+//####DESCRIPTIONEND####
+//
+//==========================================================================
+
+#ifndef _SERVICES_CRC_CRC_H_
+#define _SERVICES_CRC_CRC_H_
+
+#include <linux/types.h>
+
+#ifndef __externC
+# ifdef __cplusplus
+#  define __externC extern "C"
+# else
+#  define __externC extern
+# endif
+#endif
+
+// Compute a CRC, using the POSIX 1003 definition
+extern uint32_t 
+cyg_posix_crc32(unsigned char *s, int len);
+
+// Gary S. Brown's 32 bit CRC
+
+extern uint32_t 
+cyg_crc32(unsigned char *s, int len);
+
+// Gary S. Brown's 32 bit CRC, but accumulate the result from a
+// previous CRC calculation
+
+extern uint32_t 
+cyg_crc32_accumulate(uint32_t crc, unsigned char *s, int len);
+
+// Ethernet FCS Algorithm
+
+extern uint32_t 
+cyg_ether_crc32(unsigned char *s, int len);
+
+// Ethernet FCS algorithm, but accumulate the result from a previous
+// CRC calculation.
+
+extern uint32_t 
+cyg_ether_crc32_accumulate(uint32_t crc, unsigned char *s, int len);
+
+// 16 bit CRC with polynomial x^16+x^12+x^5+1
+
+extern uint16_t cyg_crc16(unsigned char *s, int len);
+
+#endif // _SERVICES_CRC_CRC_H_
+
+
+
diff --git a/include/xyzModem.h b/include/xyzModem.h
new file mode 100644
index 0000000000..a62a174b37
--- /dev/null
+++ b/include/xyzModem.h
@@ -0,0 +1,112 @@
+//==========================================================================
+//
+//      xyzModem.h
+//
+//      RedBoot stream handler for xyzModem protocol
+//
+//==========================================================================
+//####ECOSGPLCOPYRIGHTBEGIN####
+// -------------------------------------------
+// This file is part of eCos, the Embedded Configurable Operating System.
+// Copyright (C) 1998, 1999, 2000, 2001, 2002 Red Hat, Inc.
+// Copyright (C) 2002 Gary Thomas
+//
+// eCos is free software; you can redistribute it and/or modify it under
+// the terms of the GNU General Public License as published by the Free
+// Software Foundation; either version 2 or (at your option) any later version.
+//
+// eCos is distributed in the hope that it will be useful, but WITHOUT ANY
+// WARRANTY; without even the implied warranty of MERCHANTABILITY or
+// FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License
+// for more details.
+//
+// You should have received a copy of the GNU General Public License along
+// with eCos; if not, write to the Free Software Foundation, Inc.,
+// 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA.
+//
+// As a special exception, if other files instantiate templates or use macros
+// or inline functions from this file, or you compile this file and link it
+// with other works to produce a work based on this file, this file does not
+// by itself cause the resulting work to be covered by the GNU General Public
+// License. However the source code for this file must still be made available
+// in accordance with section (3) of the GNU General Public License.
+//
+// This exception does not invalidate any other reasons why a work based on
+// this file might be covered by the GNU General Public License.
+//
+// Alternative licenses for eCos may be arranged by contacting Red Hat, Inc.
+// at http://sources.redhat.com/ecos/ecos-license/
+// -------------------------------------------
+//####ECOSGPLCOPYRIGHTEND####
+//==========================================================================
+//#####DESCRIPTIONBEGIN####
+//
+// Author(s):    gthomas
+// Contributors: gthomas
+// Date:         2000-07-14
+// Purpose:      
+// Description:  
+//              
+// This code is part of RedBoot (tm).
+//
+//####DESCRIPTIONEND####
+//
+//==========================================================================
+
+#ifndef _XYZMODEM_H_
+#define _XYZMODEM_H_
+
+#define xyzModem_xmodem 1
+#define xyzModem_ymodem 2
+// Don't define this until the protocol support is in place
+//#define xyzModem_zmodem 3
+
+#define xyzModem_access   -1
+#define xyzModem_noZmodem -2
+#define xyzModem_timeout  -3
+#define xyzModem_eof      -4
+#define xyzModem_cancel   -5
+#define xyzModem_frame    -6
+#define xyzModem_cksum    -7
+#define xyzModem_sequence -8
+
+#define xyzModem_close 1
+#define xyzModem_abort 2
+
+
+#ifdef REDBOOT
+extern getc_io_funcs_t xyzModem_io;
+#else
+#define CYGNUM_CALL_IF_SET_COMM_ID_QUERY_CURRENT
+#define CYGACC_CALL_IF_SET_CONSOLE_COMM(x)
+
+#define diag_vprintf vprintf
+#define diag_printf printf
+#define diag_vsprintf vsprintf
+
+#define CYGACC_CALL_IF_DELAY_US(x) udelay(x)
+
+typedef struct {
+    char *filename;
+    int   mode;
+    int   chan;
+#ifdef CYGPKG_REDBOOT_NETWORKING
+    struct sockaddr_in *server;
+#endif
+} connection_info_t;
+
+typedef unsigned int bool;
+
+#define false 0
+#define true 1
+
+#endif
+
+
+int   xyzModem_stream_open(connection_info_t *info, int *err);    
+void  xyzModem_stream_close(int *err);    
+void  xyzModem_stream_terminate(bool method, int (*getc)(void));    
+int   xyzModem_stream_read(char *buf, int size, int *err);    
+char *xyzModem_error(int err);
+
+#endif // _XYZMODEM_H_