Merge branch 'master' of git://git.denx.de/u-boot-blackfin into powerpc-eldk53-warning-fixes

39 files changed, 1164 insertions, 479 deletions

diff --git a/README b/README
index 0d37d561d9..defdedbef1 100644
--- a/README
+++ b/README
@@ -898,6 +898,7 @@ The following options need to be configured:
 		CONFIG_CMD_SF		* Read/write/erase SPI NOR flash
 		CONFIG_CMD_SHA1SUM	  print sha1 memory digest
 					  (requires CONFIG_CMD_MEMORY)
+		CONFIG_CMD_SOFTSWITCH	* Soft switch setting command for BF60x
 		CONFIG_CMD_SOURCE	  "source" command Support
 		CONFIG_CMD_SPI		* SPI serial bus support
 		CONFIG_CMD_TFTPSRV	* TFTP transfer in server mode
diff --git a/arch/blackfin/cpu/Makefile b/arch/blackfin/cpu/Makefile
index 0a72ec5df3..1421cb2ca2 100644
--- a/arch/blackfin/cpu/Makefile
+++ b/arch/blackfin/cpu/Makefile
@@ -18,14 +18,12 @@ CEXTRA   := initcode.o
 SEXTRA   := start.o
 SOBJS    := interrupt.o cache.o
 COBJS-y  += cpu.o
-COBJS-y  += gpio.o
+COBJS-$(CONFIG_ADI_GPIO1) += gpio.o
 COBJS-y  += interrupts.o
 COBJS-$(CONFIG_JTAG_CONSOLE) += jtag-console.o
 COBJS-y  += os_log.o
 COBJS-y  += reset.o
-COBJS-y  += serial.o
 COBJS-y  += traps.o
-COBJS-$(CONFIG_HW_WATCHDOG)  += watchdog.o
 
 SRCS     := $(SEXTRA:.o=.S) $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
 OBJS     := $(addprefix $(obj),$(COBJS-y) $(SOBJS))
diff --git a/arch/blackfin/cpu/cpu.c b/arch/blackfin/cpu/cpu.c
index 0be2e2b835..218f57ed38 100644
--- a/arch/blackfin/cpu/cpu.c
+++ b/arch/blackfin/cpu/cpu.c
@@ -16,13 +16,39 @@
 #include <asm/mach-common/bits/core.h>
 #include <asm/mach-common/bits/ebiu.h>
 #include <asm/mach-common/bits/trace.h>
+#include <asm/serial.h>
 
 #include "cpu.h"
-#include "serial.h"
 #include "initcode.h"
 
 ulong bfin_poweron_retx;
 
+#if defined(CONFIG_CORE1_RUN) && defined(COREB_L1_CODE_START)
+void bfin_core1_start(void)
+{
+#ifdef BF561_FAMILY
+	/* Enable core 1 */
+	bfin_write_SYSCR(bfin_read_SYSCR() & ~0x0020);
+#else
+	/* Enable core 1 */
+	bfin_write32(RCU0_SVECT1, COREB_L1_CODE_START);
+	bfin_write32(RCU0_CRCTL, 0);
+
+	bfin_write32(RCU0_CRCTL, 0x2);
+
+	/* Check if core 1 starts */
+	while (!(bfin_read32(RCU0_CRSTAT) & 0x2))
+		continue;
+
+	bfin_write32(RCU0_CRCTL, 0);
+
+	/* flag to notify cces core 1 application */
+	bfin_write32(SDU0_MSG_SET, (1 << 19));
+#endif
+}
+#endif
+
+__attribute__ ((__noreturn__))
 void cpu_init_f(ulong bootflag, ulong loaded_from_ldr)
 {
 #ifndef CONFIG_BFIN_BOOTROM_USES_EVT1
@@ -72,6 +98,10 @@ void cpu_init_f(ulong bootflag, ulong loaded_from_ldr)
 # endif
 #endif
 
+#if defined(CONFIG_CORE1_RUN) && defined(COREB_L1_CODE_START)
+	bfin_core1_start();
+#endif
+
 	serial_early_puts("Board init flash\n");
 	board_init_f(bootflag);
 }
diff --git a/arch/blackfin/cpu/gpio.c b/arch/blackfin/cpu/gpio.c
index f684be531c..f74a0b7c0e 100644
--- a/arch/blackfin/cpu/gpio.c
+++ b/arch/blackfin/cpu/gpio.c
@@ -1,5 +1,6 @@
 /*
- * GPIO Abstraction Layer
+ * ADI GPIO1 Abstraction Layer
+ * Support BF50x, BF51x, BF52x, BF53x and BF561 only.
  *
  * Copyright 2006-2010 Analog Devices Inc.
  *
@@ -55,25 +56,6 @@ static struct gpio_port_t * const gpio_array[] = {
 	(struct gpio_port_t *) FIO0_FLAG_D,
 	(struct gpio_port_t *) FIO1_FLAG_D,
 	(struct gpio_port_t *) FIO2_FLAG_D,
-#elif defined(CONFIG_BF54x)
-	(struct gpio_port_t *)PORTA_FER,
-	(struct gpio_port_t *)PORTB_FER,
-	(struct gpio_port_t *)PORTC_FER,
-	(struct gpio_port_t *)PORTD_FER,
-	(struct gpio_port_t *)PORTE_FER,
-	(struct gpio_port_t *)PORTF_FER,
-	(struct gpio_port_t *)PORTG_FER,
-	(struct gpio_port_t *)PORTH_FER,
-	(struct gpio_port_t *)PORTI_FER,
-	(struct gpio_port_t *)PORTJ_FER,
-#elif defined(CONFIG_BF60x)
-	(struct gpio_port_t *)PORTA_FER,
-	(struct gpio_port_t *)PORTB_FER,
-	(struct gpio_port_t *)PORTC_FER,
-	(struct gpio_port_t *)PORTD_FER,
-	(struct gpio_port_t *)PORTE_FER,
-	(struct gpio_port_t *)PORTF_FER,
-	(struct gpio_port_t *)PORTG_FER,
 #else
 # error no gpio arrays defined
 #endif
@@ -174,12 +156,6 @@ DECLARE_RESERVED_MAP(peri, gpio_bank(MAX_RESOURCES));
 
 inline int check_gpio(unsigned gpio)
 {
-#if defined(CONFIG_BF54x)
-	if (gpio == GPIO_PB15 || gpio == GPIO_PC14 || gpio == GPIO_PC15
-	    || gpio == GPIO_PH14 || gpio == GPIO_PH15
-	    || gpio == GPIO_PJ14 || gpio == GPIO_PJ15)
-		return -EINVAL;
-#endif
 	if (gpio >= MAX_BLACKFIN_GPIOS)
 		return -EINVAL;
 	return 0;
@@ -218,18 +194,6 @@ static void port_setup(unsigned gpio, unsigned short usage)
 	else
 		*port_fer[gpio_bank(gpio)] |= gpio_bit(gpio);
 	SSYNC();
-#elif defined(CONFIG_BF54x)
-	if (usage == GPIO_USAGE)
-		gpio_array[gpio_bank(gpio)]->port_fer &= ~gpio_bit(gpio);
-	else
-		gpio_array[gpio_bank(gpio)]->port_fer |= gpio_bit(gpio);
-	SSYNC();
-#elif defined(CONFIG_BF60x)
-	if (usage == GPIO_USAGE)
-		gpio_array[gpio_bank(gpio)]->port_fer_clear = gpio_bit(gpio);
-	else
-		gpio_array[gpio_bank(gpio)]->port_fer_set = gpio_bit(gpio);
-	SSYNC();
 #endif
 }
 
@@ -304,30 +268,6 @@ static void portmux_setup(unsigned short per)
 		}
 	}
 }
-#elif defined(CONFIG_BF54x) || defined(CONFIG_BF60x)
-inline void portmux_setup(unsigned short per)
-{
-	u32 pmux;
-	u16 ident = P_IDENT(per);
-	u16 function = P_FUNCT2MUX(per);
-
-	pmux = gpio_array[gpio_bank(ident)]->port_mux;
-
-	pmux &= ~(0x3 << (2 * gpio_sub_n(ident)));
-	pmux |= (function & 0x3) << (2 * gpio_sub_n(ident));
-
-	gpio_array[gpio_bank(ident)]->port_mux = pmux;
-}
-
-inline u16 get_portmux(unsigned short per)
-{
-	u32 pmux;
-	u16 ident = P_IDENT(per);
-
-	pmux = gpio_array[gpio_bank(ident)]->port_mux;
-
-	return (pmux >> (2 * gpio_sub_n(ident)) & 0x3);
-}
 #elif defined(CONFIG_BF52x) || defined(CONFIG_BF51x)
 inline void portmux_setup(unsigned short per)
 {
@@ -344,7 +284,6 @@ inline void portmux_setup(unsigned short per)
 # define portmux_setup(...)  do { } while (0)
 #endif
 
-#if !defined(CONFIG_BF54x) && !defined(CONFIG_BF60x)
 /***********************************************************
 *
 * FUNCTIONS: Blackfin General Purpose Ports Access Functions
@@ -491,15 +430,6 @@ GET_GPIO_P(both)
 GET_GPIO_P(maska)
 GET_GPIO_P(maskb)
 
-#else /* CONFIG_BF54x */
-
-unsigned short get_gpio_dir(unsigned gpio)
-{
-	return (0x01 & (gpio_array[gpio_bank(gpio)]->dir_clear >> gpio_sub_n(gpio)));
-}
-
-#endif /* CONFIG_BF54x */
-
 /***********************************************************
 *
 * FUNCTIONS:	Blackfin Peripheral Resource Allocation
@@ -548,11 +478,7 @@ int peripheral_request(unsigned short per, const char *label)
 		 * be requested and used by several drivers
 		 */
 
-#if defined(CONFIG_BF54x) || defined(CONFIG_BF60x)
-		if (!((per & P_MAYSHARE) && get_portmux(per) == P_FUNCT2MUX(per))) {
-#else
 		if (!(per & P_MAYSHARE)) {
-#endif
 			/*
 			 * Allow that the identical pin function can
 			 * be requested from the same driver twice
@@ -641,7 +567,7 @@ void peripheral_free_list(const unsigned short per[])
 * MODIFICATION HISTORY :
 **************************************************************/
 
-int bfin_gpio_request(unsigned gpio, const char *label)
+int gpio_request(unsigned gpio, const char *label)
 {
 	if (check_gpio(gpio) < 0)
 		return -EINVAL;
@@ -665,11 +591,9 @@ int bfin_gpio_request(unsigned gpio, const char *label)
 		       gpio, get_label(gpio));
 		return -EBUSY;
 	}
-#if !defined(CONFIG_BF54x) && !defined(CONFIG_BF60x)
 	else {	/* Reset POLAR setting when acquiring a gpio for the first time */
 		set_gpio_polar(gpio, 0);
 	}
-#endif
 
 	reserve(gpio, gpio);
 	set_label(gpio, label);
@@ -679,27 +603,27 @@ int bfin_gpio_request(unsigned gpio, const char *label)
 	return 0;
 }
 
-#ifdef CONFIG_BFIN_GPIO_TRACK
-void bfin_gpio_free(unsigned gpio)
+int gpio_free(unsigned gpio)
 {
 	if (check_gpio(gpio) < 0)
-		return;
+		return -1;
 
 	if (unlikely(!is_reserved(gpio, gpio, 0))) {
 		gpio_error(gpio);
-		return;
+		return -1;
 	}
 
 	unreserve(gpio, gpio);
 
 	set_label(gpio, "free");
+
+	return 0;
 }
-#endif
 
-#ifdef BFIN_SPECIAL_GPIO_BANKS
+#ifdef ADI_SPECIAL_GPIO_BANKS
 DECLARE_RESERVED_MAP(special_gpio, gpio_bank(MAX_RESOURCES));
 
-int bfin_special_gpio_request(unsigned gpio, const char *label)
+int special_gpio_request(unsigned gpio, const char *label)
 {
 	/*
 	 * Allow that the identical GPIO can
@@ -731,7 +655,7 @@ int bfin_special_gpio_request(unsigned gpio, const char *label)
 	return 0;
 }
 
-void bfin_special_gpio_free(unsigned gpio)
+void special_gpio_free(unsigned gpio)
 {
 	if (unlikely(!is_reserved(special_gpio, gpio, 0))) {
 		gpio_error(gpio);
@@ -744,21 +668,13 @@ void bfin_special_gpio_free(unsigned gpio)
 }
 #endif
 
-static inline void __bfin_gpio_direction_input(unsigned gpio)
+static inline void __gpio_direction_input(unsigned gpio)
 {
-#if defined(CONFIG_BF54x) || defined(CONFIG_BF60x)
-	gpio_array[gpio_bank(gpio)]->dir_clear = gpio_bit(gpio);
-#else
 	gpio_array[gpio_bank(gpio)]->dir &= ~gpio_bit(gpio);
-#endif
-#if defined(CONFIG_BF60x)
-	gpio_array[gpio_bank(gpio)]->inen_set = gpio_bit(gpio);
-#else
 	gpio_array[gpio_bank(gpio)]->inen |= gpio_bit(gpio);
-#endif
 }
 
-int bfin_gpio_direction_input(unsigned gpio)
+int gpio_direction_input(unsigned gpio)
 {
 	unsigned long flags;
 
@@ -768,31 +684,24 @@ int bfin_gpio_direction_input(unsigned gpio)
 	}
 
 	local_irq_save(flags);
-	__bfin_gpio_direction_input(gpio);
+	__gpio_direction_input(gpio);
 	AWA_DUMMY_READ(inen);
 	local_irq_restore(flags);
 
 	return 0;
 }
 
-void bfin_gpio_toggle_value(unsigned gpio)
-{
-#ifdef CONFIG_BF54x
-	gpio_set_value(gpio, !gpio_get_value(gpio));
-#else
-	gpio_array[gpio_bank(gpio)]->toggle = gpio_bit(gpio);
-#endif
-}
-
-void bfin_gpio_set_value(unsigned gpio, int arg)
+int gpio_set_value(unsigned gpio, int arg)
 {
 	if (arg)
 		gpio_array[gpio_bank(gpio)]->data_set = gpio_bit(gpio);
 	else
 		gpio_array[gpio_bank(gpio)]->data_clear = gpio_bit(gpio);
+
+	return 0;
 }
 
-int bfin_gpio_direction_output(unsigned gpio, int value)
+int gpio_direction_output(unsigned gpio, int value)
 {
 	unsigned long flags;
 
@@ -803,17 +712,9 @@ int bfin_gpio_direction_output(unsigned gpio, int value)
 
 	local_irq_save(flags);
 
-#if defined(CONFIG_BF60x)
-	gpio_array[gpio_bank(gpio)]->inen_clear = gpio_bit(gpio);
-#else
 	gpio_array[gpio_bank(gpio)]->inen &= ~gpio_bit(gpio);
-#endif
 	gpio_set_value(gpio, value);
-#if defined(CONFIG_BF54x) || defined(CONFIG_BF60x)
-	gpio_array[gpio_bank(gpio)]->dir_set = gpio_bit(gpio);
-#else
 	gpio_array[gpio_bank(gpio)]->dir |= gpio_bit(gpio);
-#endif
 
 	AWA_DUMMY_READ(dir);
 	local_irq_restore(flags);
@@ -821,11 +722,8 @@ int bfin_gpio_direction_output(unsigned gpio, int value)
 	return 0;
 }
 
-int bfin_gpio_get_value(unsigned gpio)
+int gpio_get_value(unsigned gpio)
 {
-#if defined(CONFIG_BF54x) || defined(CONFIG_BF60x)
-	return (1 & (gpio_array[gpio_bank(gpio)]->data >> gpio_sub_n(gpio)));
-#else
 	unsigned long flags;
 
 	if (unlikely(get_gpio_edge(gpio))) {
@@ -838,7 +736,6 @@ int bfin_gpio_get_value(unsigned gpio)
 		return ret;
 	} else
 		return get_gpio_data(gpio);
-#endif
 }
 
 /* If we are booting from SPI and our board lacks a strong enough pull up,
@@ -860,8 +757,7 @@ void bfin_reset_boot_spi_cs(unsigned short pin)
 	udelay(1);
 }
 
-#ifdef CONFIG_BFIN_GPIO_TRACK
-void bfin_gpio_labels(void)
+void gpio_labels(void)
 {
 	int c, gpio;
 
@@ -877,4 +773,3 @@ void bfin_gpio_labels(void)
 			continue;
 	}
 }
-#endif
diff --git a/arch/blackfin/cpu/initcode.c b/arch/blackfin/cpu/initcode.c
index 1a066806d1..ffaf1017d7 100644
--- a/arch/blackfin/cpu/initcode.c
+++ b/arch/blackfin/cpu/initcode.c
@@ -13,12 +13,12 @@
 
 #include <config.h>
 #include <asm/blackfin.h>
+#include <asm/mach-common/bits/watchdog.h>
 #include <asm/mach-common/bits/bootrom.h>
 #include <asm/mach-common/bits/core.h>
+#include <asm/serial.h>
 
-#define BUG() while (1) { asm volatile("emuexcpt;"); }
-
-#include "serial.h"
+#define BUG() while (1) asm volatile("emuexcpt;");
 
 #ifndef __ADSPBF60x__
 #include <asm/mach-common/bits/ebiu.h>
@@ -193,17 +193,12 @@ static inline void serial_init(void)
 	}
 #endif
 
+#if CONFIG_BFIN_BOOT_MODE != BFIN_BOOT_BYPASS
 	if (BFIN_DEBUG_EARLY_SERIAL) {
-		int enabled = serial_early_enabled(uart_base);
-
 		serial_early_init(uart_base);
-
-		/* If the UART is off, that means we need to program
-		 * the baud rate ourselves initially.
-		 */
-		if (!enabled)
-			serial_early_set_baud(uart_base, CONFIG_BAUDRATE);
+		serial_early_set_baud(uart_base, CONFIG_BAUDRATE);
 	}
+#endif
 }
 
 __attribute__((always_inline))
@@ -262,7 +257,8 @@ program_nmi_handler(void)
 		"%1 = RETS;" /* Load addr of NMI handler */
 		"RETS = %0;" /* Restore RETS */
 		"[%2] = %1;" /* Write NMI handler */
-		: "=r"(tmp1), "=r"(tmp2) : "ab"(EVT2)
+		: "=d"(tmp1), "=d"(tmp2)
+		: "ab"(EVT2)
 	);
 }
 
@@ -462,19 +458,29 @@ program_early_devices(ADI_BOOT_DATA *bs, uint *sdivB, uint *divB, uint *vcoB)
 	if (CONFIG_BFIN_BOOT_MODE != BFIN_BOOT_BYPASS) {
 		serial_putc('e');
 #ifdef __ADSPBF60x__
+		/* Reset system event controller */
 		bfin_write_SEC_GCTL(0x2);
+		bfin_write_SEC_CCTL(0x2);
 		SSYNC();
+
+		/* Enable fault event input and system reset action in fault
+		 * controller. Route watchdog timeout event to fault interface.
+		 */
 		bfin_write_SEC_FCTL(0xc1);
+		/* Enable watchdog interrupt source */
 		bfin_write_SEC_SCTL(2, bfin_read_SEC_SCTL(2) | 0x6);
-
-		bfin_write_SEC_CCTL(0x2);
 		SSYNC();
+
+		/* Enable system event controller */
 		bfin_write_SEC_GCTL(0x1);
 		bfin_write_SEC_CCTL(0x1);
+		SSYNC();
 #endif
+		bfin_write_WDOG_CTL(WDDIS);
+		SSYNC();
 		bfin_write_WDOG_CNT(MSEC_TO_SCLK(CONFIG_HW_WATCHDOG_TIMEOUT_INITCODE));
 #if CONFIG_BFIN_BOOT_MODE != BFIN_BOOT_UART
-		bfin_write_WDOG_CTL(0);
+		bfin_write_WDOG_CTL(WDEN);
 #endif
 		serial_putc('f');
 	}
@@ -713,37 +719,32 @@ program_clocks(ADI_BOOT_DATA *bs, bool put_into_srfs)
 __attribute__((always_inline)) static inline void
 update_serial_clocks(ADI_BOOT_DATA *bs, uint sdivB, uint divB, uint vcoB)
 {
-	serial_putc('a');
-
 	/* Since we've changed the SCLK above, we may need to update
 	 * the UART divisors (UART baud rates are based on SCLK).
 	 * Do the division by hand as there are no native instructions
 	 * for dividing which means we'd generate a libgcc reference.
 	 */
-	if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_UART) {
-		unsigned int sdivR, vcoR;
-		int dividend = sdivB * divB * vcoR;
-		int divisor = vcoB * sdivR;
-		unsigned int quotient;
+	unsigned int sdivR, vcoR;
+	unsigned int dividend;
+	unsigned int divisor;
+	unsigned int quotient;
 
-		serial_putc('b');
+	serial_putc('a');
 
 #ifdef __ADSPBF60x__
-		sdivR = bfin_read_CGU_DIV();
-		sdivR = ((sdivR >> 8) & 0x1f) * ((sdivR >> 5) & 0x7);
-		vcoR = (bfin_read_CGU_CTL() >> 8) & 0x7f;
+	sdivR = bfin_read_CGU_DIV();
+	sdivR = ((sdivR >> 8) & 0x1f) * ((sdivR >> 5) & 0x7);
+	vcoR = (bfin_read_CGU_CTL() >> 8) & 0x7f;
 #else
-		sdivR = bfin_read_PLL_DIV() & 0xf;
-		vcoR = (bfin_read_PLL_CTL() >> 9) & 0x3f;
+	sdivR = bfin_read_PLL_DIV() & 0xf;
+	vcoR = (bfin_read_PLL_CTL() >> 9) & 0x3f;
 #endif
 
-		for (quotient = 0; dividend > 0; ++quotient)
-			dividend -= divisor;
-		serial_early_put_div(quotient - ANOMALY_05000230);
-		serial_putc('c');
-	}
-
-	serial_putc('d');
+	dividend = sdivB * divB * vcoR;
+	divisor = vcoB * sdivR;
+	quotient = early_division(dividend, divisor);
+	serial_early_put_div(quotient - ANOMALY_05000230);
+	serial_putc('c');
 }
 
 __attribute__((always_inline)) static inline void
diff --git a/arch/blackfin/cpu/start.S b/arch/blackfin/cpu/start.S
index 7155fc858b..da084a87c6 100644
--- a/arch/blackfin/cpu/start.S
+++ b/arch/blackfin/cpu/start.S
@@ -32,10 +32,10 @@
 
 #include <config.h>
 #include <asm/blackfin.h>
+#include <asm/mach-common/bits/watchdog.h>
 #include <asm/mach-common/bits/core.h>
 #include <asm/mach-common/bits/pll.h>
-
-#include "serial.h"
+#include <asm/serial.h>
 
 /* It may seem odd that we make calls to functions even though we haven't
  * relocated ourselves yet out of {flash,ram,wherever}.  This is OK because
@@ -65,20 +65,29 @@ ENTRY(_start)
 	p5.h = HI(COREMMR_BASE);
 
 #ifdef CONFIG_HW_WATCHDOG
-#ifndef __ADSPBF60x__
-# ifndef CONFIG_HW_WATCHDOG_TIMEOUT_START
-#  define CONFIG_HW_WATCHDOG_TIMEOUT_START 5000
-# endif
-	/* Program the watchdog with an initial timeout of ~5 seconds.
+	/* Program the watchdog with default timeout of ~5 seconds.
 	 * That should be long enough to bootstrap ourselves up and
 	 * then the common u-boot code can take over.
 	 */
+	r1 = WDDIS;
+# ifdef __ADSPBF60x__
+	[p4 + (WDOG_CTL - SYSMMR_BASE)] = r1;
+# else
+	W[p4 + (WDOG_CTL - SYSMMR_BASE)] = r1;
+# endif
+	SSYNC;
 	r0 = 0;
-	r0.h = HI(MSEC_TO_SCLK(CONFIG_HW_WATCHDOG_TIMEOUT_START));
+	r0.h = HI(MSEC_TO_SCLK(CONFIG_WATCHDOG_TIMEOUT_MSECS));
 	[p4 + (WDOG_CNT - SYSMMR_BASE)] = r0;
+	SSYNC;
+	r1 = WDEN;
 	/* fire up the watchdog - R0.L above needs to be 0x0000 */
-	W[p4 + (WDOG_CTL - SYSMMR_BASE)] = r0;
-#endif
+# ifdef __ADSPBF60x__
+	[p4 + (WDOG_CTL - SYSMMR_BASE)] = r1;
+# else
+	W[p4 + (WDOG_CTL - SYSMMR_BASE)] = r1;
+# endif
+	SSYNC;
 #endif
 
 	/* Turn on the serial for debugging the init process */
diff --git a/arch/blackfin/include/asm/clock.h b/arch/blackfin/include/asm/clock.h
new file mode 100644
index 0000000000..f1fcd40499
--- /dev/null
+++ b/arch/blackfin/include/asm/clock.h
@@ -0,0 +1,78 @@
+
+/*
+ * Copyright (C) 2012 Analog Devices Inc.
+ * Licensed under the GPL-2 or later.
+ */
+
+#ifndef __CLOCK_H__
+#define __CLOCK_H__
+
+#include <asm/blackfin.h>
+#ifdef PLL_CTL
+#include <asm/mach-common/bits/pll.h>
+# define pll_is_bypassed() (bfin_read_PLL_CTL() & BYPASS)
+#else
+#include <asm/mach-common/bits/cgu.h>
+# define pll_is_bypassed() (bfin_read_CGU_STAT() & PLLBP)
+# define bfin_read_PLL_CTL() bfin_read_CGU_CTL()
+# define bfin_read_PLL_DIV() bfin_read_CGU_DIV()
+# define SSEL SYSSEL
+# define SSEL_P SYSSEL_P
+#endif
+
+__attribute__((always_inline))
+static inline uint32_t early_division(uint32_t dividend, uint32_t divisor)
+{
+	uint32_t quotient;
+	uint32_t i, j;
+
+	for (quotient = 1, i = 1; dividend > divisor; ++i) {
+		j = divisor << i;
+		if (j > dividend || (j & 0x80000000)) {
+			--i;
+			quotient += (1 << i);
+			dividend -= (divisor << i);
+			i = 0;
+		}
+	}
+
+	return quotient;
+}
+
+__attribute__((always_inline))
+static inline uint32_t early_get_uart_clk(void)
+{
+	uint32_t msel, pll_ctl, vco;
+	uint32_t div, ssel, sclk, uclk;
+
+	pll_ctl = bfin_read_PLL_CTL();
+	msel = (pll_ctl & MSEL) >> MSEL_P;
+	if (msel == 0)
+		msel = (MSEL >> MSEL_P) + 1;
+
+	vco = (CONFIG_CLKIN_HZ >> (pll_ctl & DF)) * msel;
+	sclk = vco;
+	if (!pll_is_bypassed()) {
+		div = bfin_read_PLL_DIV();
+		ssel = (div & SSEL) >> SSEL_P;
+#if CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_BYPASS
+		sclk = vco/ssel;
+#else
+		sclk = early_division(vco, ssel);
+#endif
+	}
+	uclk = sclk;
+#ifdef CGU_DIV
+	ssel = (div & S0SEL) >> S0SEL_P;
+	uclk = early_division(sclk, ssel);
+#endif
+	return uclk;
+}
+
+#ifdef CGU_DIV
+# define get_uart_clk get_sclk0
+#else
+# define get_uart_clk get_sclk
+#endif
+
+#endif
diff --git a/arch/blackfin/include/asm/dma.h b/arch/blackfin/include/asm/dma.h
index ef1db6e99c..8a7c07933e 100644
--- a/arch/blackfin/include/asm/dma.h
+++ b/arch/blackfin/include/asm/dma.h
@@ -17,21 +17,21 @@
 
 struct dmasg_large {
 	void *next_desc_addr;
-	unsigned long start_addr;
-	unsigned short cfg;
-	unsigned short x_count;
-	short x_modify;
-	unsigned short y_count;
-	short y_modify;
+	u32 start_addr;
+	u16 cfg;
+	u16 x_count;
+	s16 x_modify;
+	u16 y_count;
+	s16 y_modify;
 } __attribute__((packed));
 
 struct dmasg {
-	unsigned long start_addr;
-	unsigned short cfg;
-	unsigned short x_count;
-	short x_modify;
-	unsigned short y_count;
-	short y_modify;
+	u32 start_addr;
+	u16 cfg;
+	u16 x_count;
+	s16 x_modify;
+	u16 y_count;
+	s16 y_modify;
 } __attribute__((packed));
 
 struct dma_register {
diff --git a/arch/blackfin/include/asm/gpio.h b/arch/blackfin/include/asm/gpio.h
index 05131b5e8b..58a6191107 100644
--- a/arch/blackfin/include/asm/gpio.h
+++ b/arch/blackfin/include/asm/gpio.h
@@ -7,6 +7,8 @@
 #ifndef __ARCH_BLACKFIN_GPIO_H__
 #define __ARCH_BLACKFIN_GPIO_H__
 
+#include <asm-generic/gpio.h>
+
 #define gpio_bank(x)	((x) >> 4)
 #define gpio_bit(x)	(1<<((x) & 0xF))
 #define gpio_sub_n(x)	((x) & 0xF)
@@ -65,10 +67,11 @@
 
 #define PERIPHERAL_USAGE 1
 #define GPIO_USAGE 0
+#define MAX_GPIOS MAX_BLACKFIN_GPIOS
 
 #ifndef __ASSEMBLY__
 
-#if !defined(CONFIG_BF54x) && !defined(CONFIG_BF60x)
+#ifdef CONFIG_ADI_GPIO1
 void set_gpio_dir(unsigned, unsigned short);
 void set_gpio_inen(unsigned, unsigned short);
 void set_gpio_polar(unsigned, unsigned short);
@@ -140,61 +143,16 @@ struct gpio_port_t {
 };
 #endif
 
-#ifdef CONFIG_BFIN_GPIO_TRACK
-void bfin_gpio_labels(void);
-void bfin_gpio_free(unsigned gpio);
-#else
-#define bfin_gpio_labels()
-#define bfin_gpio_free(gpio)
-#define bfin_gpio_request(gpio, label) bfin_gpio_request(gpio)
-#define bfin_special_gpio_request(gpio, label) bfin_special_gpio_request(gpio)
-#endif
-
-#ifdef BFIN_SPECIAL_GPIO_BANKS
-void bfin_special_gpio_free(unsigned gpio);
-int bfin_special_gpio_request(unsigned gpio, const char *label);
+#ifdef ADI_SPECIAL_GPIO_BANKS
+void special_gpio_free(unsigned gpio);
+int special_gpio_request(unsigned gpio, const char *label);
 #endif
 
-int bfin_gpio_request(unsigned gpio, const char *label);
-int bfin_gpio_direction_input(unsigned gpio);
-int bfin_gpio_direction_output(unsigned gpio, int value);
-int bfin_gpio_get_value(unsigned gpio);
-void bfin_gpio_set_value(unsigned gpio, int value);
-void bfin_gpio_toggle_value(unsigned gpio);
-
-static inline int gpio_request(unsigned gpio, const char *label)
-{
-	return bfin_gpio_request(gpio, label);
-}
-
-static inline void gpio_free(unsigned gpio)
-{
-	return bfin_gpio_free(gpio);
-}
-
-static inline int gpio_direction_input(unsigned gpio)
-{
-	return bfin_gpio_direction_input(gpio);
-}
-
-static inline int gpio_direction_output(unsigned gpio, int value)
-{
-	return bfin_gpio_direction_output(gpio, value);
-}
-
-static inline int gpio_get_value(unsigned gpio)
-{
-	return bfin_gpio_get_value(gpio);
-}
-
-static inline void gpio_set_value(unsigned gpio, int value)
-{
-	return bfin_gpio_set_value(gpio, value);
-}
+void gpio_labels(void);
 
 static inline int gpio_is_valid(int number)
 {
-	return number >= 0 && number < MAX_BLACKFIN_GPIOS;
+	return number >= 0 && number < MAX_GPIOS;
 }
 
 #include <linux/ctype.h>
@@ -248,7 +206,7 @@ static inline int name_to_gpio(const char *name)
 }
 #define name_to_gpio(n) name_to_gpio(n)
 
-#define gpio_status() bfin_gpio_labels()
+#define gpio_status() gpio_labels()
 
 #endif /* __ASSEMBLY__ */
 
diff --git a/arch/blackfin/include/asm/mach-bf561/BF561_def.h b/arch/blackfin/include/asm/mach-bf561/BF561_def.h
index a7ff5a3feb..8fd552f2a1 100644
--- a/arch/blackfin/include/asm/mach-bf561/BF561_def.h
+++ b/arch/blackfin/include/asm/mach-bf561/BF561_def.h
@@ -714,4 +714,6 @@
 #define L1_INST_SRAM_SIZE (0xFFA03FFF - 0xFFA00000 + 1)
 #define L1_INST_SRAM_END (L1_INST_SRAM + L1_INST_SRAM_SIZE)
 
+#define COREB_L1_CODE_START       0xFF600000
+
 #endif /* __BFIN_DEF_ADSP_BF561_proc__ */
diff --git a/arch/blackfin/include/asm/mach-bf609/BF609_def.h b/arch/blackfin/include/asm/mach-bf609/BF609_def.h
index 8c1dcd006e..02b81d3fd1 100644
--- a/arch/blackfin/include/asm/mach-bf609/BF609_def.h
+++ b/arch/blackfin/include/asm/mach-bf609/BF609_def.h
@@ -128,6 +128,9 @@
 #define EMAC0_MACCFG      0xFFC20000 /* EMAC0 MAC Configuration Register */
 #define EMAC1_MACCFG      0xFFC22000 /* EMAC1 MAC Configuration Register */
 
+#define SPI0_REGBASE      0xFFC40400 /* SPI0 Base Address */
+#define SPI1_REGBASE      0xFFC40500 /* SPI1 Base Address */
+
 #define DMA10_DSCPTR_NXT  0xFFC05000 /* DMA10 Pointer to Next Initial Desc */
 #define DMA10_ADDRSTART   0xFFC05004 /* DMA10 Start Address of Current Buf */
 #define DMA10_CFG         0xFFC05008 /* DMA10 Configuration Register */
@@ -244,4 +247,6 @@
 #define L1_INST_SRAM_SIZE 0x8000
 #define L1_INST_SRAM_END (L1_INST_SRAM + L1_INST_SRAM_SIZE)
 
+#define COREB_L1_CODE_START       0xFF600000
+
 #endif /* __BFIN_DEF_ADSP_BF609_proc__ */
diff --git a/arch/blackfin/include/asm/portmux.h b/arch/blackfin/include/asm/portmux.h
index 300ef44fd1..003694b515 100644
--- a/arch/blackfin/include/asm/portmux.h
+++ b/arch/blackfin/include/asm/portmux.h
@@ -17,11 +17,6 @@
 #define P_MAYSHARE	0x2000
 #define P_DONTCARE	0x1000
 
-#ifndef CONFIG_BFIN_GPIO_TRACK
-#define peripheral_request(per, label) peripheral_request(per)
-#define peripheral_request_list(per, label) peripheral_request_list(per)
-#endif
-
 #ifndef __ASSEMBLY__
 
 int peripheral_request(unsigned short per, const char *label);
diff --git a/arch/blackfin/cpu/serial.h b/arch/blackfin/include/asm/serial.h
index 9200339668..87a337d1b4 100644
--- a/arch/blackfin/cpu/serial.h
+++ b/arch/blackfin/include/asm/serial.h
@@ -78,19 +78,31 @@ static inline void serial_early_puts(const char *s)
 #else
 
 .macro serial_early_init
-#ifdef CONFIG_DEBUG_EARLY_SERIAL
-	call _serial_initialize;
+#if defined(CONFIG_DEBUG_EARLY_SERIAL) && !defined(CONFIG_UART_MEM)
+	call __serial_early_init;
 #endif
 .endm
 
 .macro serial_early_set_baud
-#ifdef CONFIG_DEBUG_EARLY_SERIAL
+#if defined(CONFIG_DEBUG_EARLY_SERIAL) && !defined(CONFIG_UART_MEM)
 	R0.L = LO(CONFIG_BAUDRATE);
 	R0.H = HI(CONFIG_BAUDRATE);
-	call _serial_set_baud;
+	call __serial_early_set_baud;
 #endif
 .endm
 
+#if CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_BYPASS
+#define update_serial_early_string_addr \
+	R1.L = _start; \
+	R1.H = _start; \
+	R0 = R0 - R1; \
+	R1.L = 0; \
+	R1.H = 0x2000; \
+	R0 = R0 + R1;
+#else
+#define update_serial_early_string_addr
+#endif
+
 /* Since we embed the string right into our .text section, we need
  * to find its address.  We do this by getting our PC and adding 2
  * bytes (which is the length of the jump instruction).  Then we
@@ -108,7 +120,8 @@ static inline void serial_early_puts(const char *s)
 	.previous; \
 	R0.L = 7b; \
 	R0.H = 7b; \
-	call _serial_puts;
+	update_serial_early_string_addr \
+	call _uart_early_puts;
 #else
 # define serial_early_puts(str)
 #endif
diff --git a/arch/blackfin/cpu/serial1.h b/arch/blackfin/include/asm/serial1.h
index a20175bc7f..467d3817f1 100644
--- a/arch/blackfin/cpu/serial1.h
+++ b/arch/blackfin/include/asm/serial1.h
@@ -15,6 +15,8 @@
 
 #ifndef __ASSEMBLY__
 
+#include <asm/clock.h>
+
 #define MMR_UART(n) _PASTE_UART(n, UART, DLL)
 #ifdef UART_DLL
 # define UART0_DLL UART_DLL
@@ -230,19 +232,6 @@ static inline void serial_early_do_portmux(void)
 }
 
 __attribute__((always_inline))
-static inline uint32_t uart_sclk(void)
-{
-#if defined(BFIN_IN_INITCODE) || defined(CONFIG_DEBUG_EARLY_SERIAL)
-	/* We cannot use get_sclk() early on as it uses
-	 * caches in external memory
-	 */
-	return CONFIG_CLKIN_HZ * CONFIG_VCO_MULT / CONFIG_SCLK_DIV;
-#else
-	return get_sclk();
-#endif
-}
-
-__attribute__((always_inline))
 static inline int uart_init(uint32_t uart_base)
 {
 	/* always enable UART -- avoids anomalies 05000309 and 05000350 */
@@ -275,21 +264,8 @@ static inline int serial_early_uninit(uint32_t uart_base)
 }
 
 __attribute__((always_inline))
-static inline int serial_early_enabled(uint32_t uart_base)
+static inline void serial_set_divisor(uint32_t uart_base, uint16_t divisor)
 {
-	return bfin_read(&pUART->gctl) & UCEN;
-}
-
-__attribute__((always_inline))
-static inline void serial_early_set_baud(uint32_t uart_base, uint32_t baud)
-{
-	/* Translate from baud into divisor in terms of SCLK.  The
-	 * weird multiplication is to make sure we over sample just
-	 * a little rather than under sample the incoming signals.
-	 */
-	uint16_t divisor = (uart_sclk() + (baud * 8)) / (baud * 16) -
-			ANOMALY_05000230;
-
 	/* Set DLAB in LCR to Access DLL and DLH */
 	ACCESS_LATCH();
 	SSYNC();
@@ -305,6 +281,24 @@ static inline void serial_early_set_baud(uint32_t uart_base, uint32_t baud)
 }
 
 __attribute__((always_inline))
+static inline void serial_early_set_baud(uint32_t uart_base, uint32_t baud)
+{
+	/* Translate from baud into divisor in terms of SCLK.  The
+	 * weird multiplication is to make sure we over sample just
+	 * a little rather than under sample the incoming signals.
+	 */
+#if CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_BYPASS
+	uint16_t divisor = (early_get_uart_clk() + baud * 8) / (baud * 16)
+			- ANOMALY_05000230;
+#else
+	uint16_t divisor = early_division(early_get_uart_clk() + (baud * 8),
+			baud * 16) - ANOMALY_05000230;
+#endif
+
+	serial_set_divisor(uart_base, divisor);
+}
+
+__attribute__((always_inline))
 static inline void serial_early_put_div(uint16_t divisor)
 {
 	uint32_t uart_base = UART_BASE;
diff --git a/arch/blackfin/cpu/serial4.h b/arch/blackfin/include/asm/serial4.h
index 887845c186..65483960b9 100644
--- a/arch/blackfin/cpu/serial4.h
+++ b/arch/blackfin/include/asm/serial4.h
@@ -15,6 +15,8 @@
 
 #ifndef __ASSEMBLY__
 
+#include <asm/clock.h>
+
 #define MMR_UART(n) _PASTE_UART(n, UART, REVID)
 #define UART_BASE MMR_UART(CONFIG_UART_CONSOLE)
 
@@ -84,20 +86,6 @@ static inline void serial_early_do_portmux(void)
 }
 
 __attribute__((always_inline))
-static inline uint32_t uart_sclk(void)
-{
-#if defined(BFIN_IN_INITCODE) || defined(CONFIG_DEBUG_EARLY_SERIAL)
-	/* We cannot use get_sclk() early on as it uses caches in
-	 * external memory
-	 */
-	return CONFIG_CLKIN_HZ * CONFIG_VCO_MULT / CONFIG_SCLK_DIV /
-		CONFIG_SCLK0_DIV;
-#else
-	return get_sclk0();
-#endif
-}
-
-__attribute__((always_inline))
 static inline int uart_init(uint32_t uart_base)
 {
 	/* always enable UART to 8-bit mode */
@@ -127,19 +115,20 @@ static inline int serial_early_uninit(uint32_t uart_base)
 }
 
 __attribute__((always_inline))
-static inline int serial_early_enabled(uint32_t uart_base)
+static inline void serial_set_divisor(uint32_t uart_base, uint16_t divisor)
 {
-	return bfin_read(&pUART->control) & UEN;
+	/* Program the divisor to get the baud rate we want */
+	bfin_write(&pUART->clock, divisor);
+	SSYNC();
 }
 
 __attribute__((always_inline))
 static inline void serial_early_set_baud(uint32_t uart_base, uint32_t baud)
 {
-	uint32_t divisor = uart_sclk() / (baud * 16);
+	uint16_t divisor = early_division(early_get_uart_clk(), baud * 16);
 
 	/* Program the divisor to get the baud rate we want */
-	bfin_write(&pUART->clock, divisor);
-	SSYNC();
+	serial_set_divisor(uart_base, divisor);
 }
 
 __attribute__((always_inline))
diff --git a/arch/blackfin/include/asm/soft_switch.h b/arch/blackfin/include/asm/soft_switch.h
new file mode 100644
index 0000000000..ff8e44d8be
--- /dev/null
+++ b/arch/blackfin/include/asm/soft_switch.h
@@ -0,0 +1,18 @@
+/*
+ * U-boot - main board file
+ *
+ * Copyright (c) 2008-2012 Analog Devices Inc.
+ *
+ * Licensed under the GPL-2 or later.
+ */
+
+#ifndef __SOFT_SWITCH_H__
+#define __SOFT_SWITCH_H__
+
+#define IO_PORT_A              0
+#define IO_PORT_B              1
+#define IO_PORT_INPUT          0
+#define IO_PORT_OUTPUT         1
+
+int config_switch_bit(int num, int port, int bit, int dir, uchar value);
+#endif
diff --git a/arch/blackfin/lib/board.c b/arch/blackfin/lib/board.c
index ccea3b9fb1..f1d55470e8 100644
--- a/arch/blackfin/lib/board.c
+++ b/arch/blackfin/lib/board.c
@@ -231,6 +231,8 @@ static int global_board_data_init(void)
 	bd->bi_sclk = get_sclk();
 	bd->bi_memstart = CONFIG_SYS_SDRAM_BASE;
 	bd->bi_memsize = CONFIG_SYS_MAX_RAM_SIZE;
+	bd->bi_baudrate = (gd->baudrate > 0)
+		? simple_strtoul(gd->baudrate, NULL, 10) : CONFIG_BAUDRATE;
 
 	return 0;
 }
@@ -277,9 +279,9 @@ void board_init_f(ulong bootflag)
 	dcache_enable();
 #endif
 
-#ifdef CONFIG_WATCHDOG
+#ifdef CONFIG_HW_WATCHDOG
 	serial_early_puts("Setting up external watchdog\n");
-	watchdog_init();
+	hw_watchdog_init();
 #endif
 
 #ifdef DEBUG
diff --git a/arch/blackfin/lib/clocks.c b/arch/blackfin/lib/clocks.c
index d852f5ebed..97795e11ac 100644
--- a/arch/blackfin/lib/clocks.c
+++ b/arch/blackfin/lib/clocks.c
@@ -7,17 +7,7 @@
  */
 
 #include <common.h>
-#include <asm/blackfin.h>
-
-#ifdef PLL_CTL
-# include <asm/mach-common/bits/pll.h>
-# define pll_is_bypassed() (bfin_read_PLL_STAT() & DF)
-#else
-# include <asm/mach-common/bits/cgu.h>
-# define pll_is_bypassed() (bfin_read_CGU_STAT() & PLLBP)
-# define bfin_read_PLL_CTL() bfin_read_CGU_CTL()
-# define bfin_read_PLL_DIV() bfin_read_CGU_DIV()
-#endif
+#include <asm/clock.h>
 
 /* Get the voltage input multiplier */
 u_long get_vco(void)
diff --git a/arch/blackfin/lib/string.c b/arch/blackfin/lib/string.c
index 44d8c6d906..5b7ac0b91a 100644
--- a/arch/blackfin/lib/string.c
+++ b/arch/blackfin/lib/string.c
@@ -128,10 +128,12 @@ static void dma_calc_size(unsigned long ldst, unsigned long lsrc, size_t count,
 	unsigned long limit;
 
 #ifdef MSIZE
-	limit = 6;
+	/* The max memory DMA memory transfer size is 32 bytes. */
+	limit = 5;
 	*dshift = MSIZE_P;
 #else
-	limit = 3;
+	/* The max memory DMA memory transfer size is 4 bytes. */
+	limit = 2;
 	*dshift = WDSIZE_P;
 #endif
 
@@ -170,7 +172,8 @@ void dma_memcpy_nocache(void *dst, const void *src, size_t count)
 	mod = 1 << bpos;
 
 #ifdef PSIZE
-	dsize |= min(3, bpos) << PSIZE_P;
+	/* The max memory DMA peripheral transfer size is 4 bytes. */
+	dsize |= min(2, bpos) << PSIZE_P;
 #endif
 
 	/* Copy sram functions from sdram to sram */
diff --git a/board/bf609-ezkit/soft_switch.c b/board/bf609-ezkit/soft_switch.c
new file mode 100644
index 0000000000..e0c8d93fe7
--- /dev/null
+++ b/board/bf609-ezkit/soft_switch.c
@@ -0,0 +1,171 @@
+/*
+ * U-boot - main board file
+ *
+ * Copyright (c) 2008-2011 Analog Devices Inc.
+ *
+ * Licensed under the GPL-2 or later.
+ */
+
+#include <common.h>
+#include <asm/blackfin.h>
+#include <asm/io.h>
+#include <i2c.h>
+#include "soft_switch.h"
+
+struct switch_config {
+	uchar dir0; /* IODIRA */
+	uchar dir1; /* IODIRB */
+	uchar value0; /* OLATA */
+	uchar value1; /* OLATB */
+};
+
+static struct switch_config switch_config_array[NUM_SWITCH] = {
+	{
+/*
+	U45 Port A                     U45 Port B
+
+	7---------------  RMII_CLK_EN  |  7--------------- ~TEMP_THERM_EN
+	| 6------------- ~CNT0ZM_EN    |  | 6------------- ~TEMP_IRQ_EN
+	| | 5----------- ~CNT0DG_EN    |  | | 5----------- ~UART0CTS_146_EN
+	| | | 4--------- ~CNT0UD_EN    |  | | | 4--------- ~UART0CTS_RST_EN
+	| | | | 3------- ~CAN0RX_EN    |  | | | | 3------- ~UART0CTS_RTS_LPBK
+	| | | | | 2----- ~CAN0_ERR_EN  |  | | | | | 2----- ~UART0CTS_EN
+	| | | | | | 1--- ~CAN_STB      |  | | | | | | 1--- ~UART0RX_EN
+	| | | | | | | 0-  CAN_EN       |  | | | | | | | 0- ~UART0RTS_EN
+	| | | | | | | |                |  | | | | | | | |
+	O O O O O O O O                |  O O O O O O O O   (I/O direction)
+	1 0 0 0 0 0 1 1                |  1 1 1 1 1 0 0 0   (value being set)
+*/
+		.dir0 = 0x0, /* all output */
+		.dir1 = 0x0, /* all output */
+		.value0 = RMII_CLK_EN | CAN_STB | CAN_EN,
+		.value1 = TEMP_THERM_EN | TEMP_IRQ_EN | UART0CTS_146_EN
+				| UART0CTS_RST_EN | UART0CTS_RTS_LPBK,
+	},
+	{
+/*
+	U46 Port A                       U46 Port B
+
+	7--------------- ~LED4_GPIO_EN   |  7---------------  EMPTY
+	| 6------------- ~LED3_GPIO_EN   |  | 6------------- ~SPI0D3_EN
+	| | 5----------- ~LED2_GPIO_EN   |  | | 5----------- ~SPI0D2_EN
+	| | | 4--------- ~LED1_GPIO_EN   |  | | | 4--------- ~SPIFLASH_CS_EN
+	| | | | 3-------  SMC0_LP0_EN    |  | | | | 3------- ~SD_WP_EN
+	| | | | | 2-----  EMPTY          |  | | | | | 2----- ~SD_CD_EN
+	| | | | | | 1---  SMC0_EPPI2     |  | | | | | | 1--- ~PUSHBUTTON2_EN
+			  _LP1_SWITCH
+	| | | | | | | 0-  OVERRIDE_SMC0  |  | | | | | | | 0- ~PUSHBUTTON1_EN
+			  _LP0_BOOT
+	| | | | | | | |                  |  | | | | | | | |
+	O O O O O O O O                  |  O O O O O O O O   (I/O direction)
+	0 0 0 0 0 X 0 1                  |  X 0 0 0 0 0 0 0   (value being set)
+*/
+		.dir0 = 0x0, /* all output */
+		.dir1 = 0x0, /* all output */
+#ifdef CONFIG_BFIN_LINKPORT
+		.value0 = OVERRIDE_SMC0_LP0_BOOT,
+#else
+		.value0 = SMC0_EPPI2_LP1_SWITCH,
+#endif
+		.value1 = 0x0,
+	},
+	{
+/*
+	U47 Port A                         U47 Port B
+
+	7--------------- ~PD2_SPI0MISO |  7---------------  EMPTY
+			  _EI3_EN
+	| 6------------- ~PD1_SPI0D3   |  | 6-------------  EMPTY
+			  _EPPI1D17
+			  _SPI0SEL2
+			  _EI3_EN
+	| | 5----------- ~PD0_SPI0D2   |  | | 5-----------  EMPTY
+			  _EPPI1D16
+			  _SPI0SEL3
+			  _EI3_EN
+	| | | 4--------- ~WAKE_PUSH    |  | | | 4---------  EMPTY
+			  BUTTON_EN
+	| | | | 3------- ~ETHERNET_EN  |  | | | | 3-------  EMPTY
+	| | | | | 2-----  PHYAD0       |  | | | | | 2-----  EMPTY
+	| | | | | | 1---  PHY_PWR      |  | | | | | | 1--- ~PD4_SPI0CK_EI3_EN
+			  _DWN_INT
+	| | | | | | | 0- ~PHYINT_EN    |  | | | | | | | 0- ~PD3_SPI0MOSI_EI3_EN
+	| | | | | | | |                |  | | | | | | | |
+	O O O O O I I O                |  O O O O O O O O   (I/O direction)
+	1 1 1 0 0 0 0 0                |  X X X X X X 1 1   (value being set)
+*/
+		.dir0 = 0x6, /* bits 1 and 2 input, all others output */
+		.dir1 = 0x0, /* all output */
+		.value0 = PD1_SPI0D3_EN | PD0_SPI0D2_EN,
+		.value1 = 0,
+	},
+};
+
+static int setup_soft_switch(int addr, struct switch_config *config)
+{
+	int ret = 0;
+
+	ret = i2c_write(addr, OLATA, 1, &config->value0, 1);
+	if (ret)
+		return ret;
+	ret = i2c_write(addr, OLATB, 1, &config->value1, 1);
+	if (ret)
+		return ret;
+
+	ret = i2c_write(addr, IODIRA, 1, &config->dir0, 1);
+	if (ret)
+		return ret;
+	return i2c_write(addr, IODIRB, 1, &config->dir1, 1);
+}
+
+int config_switch_bit(int addr, int port, int bit, int dir, uchar value)
+{
+	int ret, data_reg, dir_reg;
+	uchar tmp;
+
+	if (port == IO_PORT_A) {
+		data_reg = OLATA;
+		dir_reg = IODIRA;
+	} else {
+		data_reg = OLATB;
+		dir_reg = IODIRB;
+	}
+
+	if (dir == IO_PORT_INPUT) {
+		ret = i2c_read(addr, dir_reg, 1, &tmp, 1);
+		if (ret)
+			return ret;
+		tmp |= bit;
+		return i2c_write(addr, dir_reg, 1, &tmp, 1);
+	} else {
+		ret = i2c_read(addr, data_reg, 1, &tmp, 1);
+		if (ret)
+			return ret;
+		if (value)
+			tmp |= bit;
+		else
+			tmp &= ~bit;
+		ret = i2c_write(addr, data_reg, 1, &tmp, 1);
+		if (ret)
+			return ret;
+		ret = i2c_read(addr, dir_reg, 1, &tmp, 1);
+		if (ret)
+			return ret;
+		tmp &= ~bit;
+		return i2c_write(addr, dir_reg, 1, &tmp, 1);
+	}
+}
+
+int setup_board_switches(void)
+{
+	int ret;
+	int i;
+
+	for (i = 0; i < NUM_SWITCH; i++) {
+		ret = setup_soft_switch(SWITCH_ADDR + i,
+				&switch_config_array[i]);
+		if (ret)
+			return ret;
+	}
+	return 0;
+}
diff --git a/board/bf609-ezkit/soft_switch.h b/board/bf609-ezkit/soft_switch.h
new file mode 100644
index 0000000000..d147fe1378
--- /dev/null
+++ b/board/bf609-ezkit/soft_switch.h
@@ -0,0 +1,80 @@
+/*
+ * U-boot - main board file
+ *
+ * Copyright (c) 2008-2011 Analog Devices Inc.
+ *
+ * Licensed under the GPL-2 or later.
+ */
+
+#ifndef __BOARD_SOFT_SWITCH_H__
+#define __BOARD_SOFT_SWITCH_H__
+
+#include <asm/soft_switch.h>
+
+/* switch 0 port A */
+#define CAN_EN                 0x1
+#define CAN_STB                0x2
+#define CAN0_ERR_EN            0x4
+#define CAN0RX_EN              0x8
+#define CNT0UD_EN              0x10
+#define CNT0DG_EN              0x20
+#define CNT0ZM_EN              0x40
+#define RMII_CLK_EN            0x80
+
+/* switch 0 port B */
+#define UART0RTS_EN            0x1
+#define UART0RX_EN             0x2
+#define UART0CTS_EN            0x4
+#define UART0CTS_RTS_LPBK      0x8
+#define UART0CTS_RST_EN        0x10
+#define UART0CTS_146_EN        0x20
+#define TEMP_IRQ_EN            0x40
+#define TEMP_THERM_EN          0x80
+
+/* switch 1 port A */
+#define OVERRIDE_SMC0_LP0_BOOT 0x1
+#define SMC0_EPPI2_LP1_SWITCH  0x2
+#define SMC0_LP0_EN            0x8
+#define LED1_GPIO_EN           0x10
+#define LED2_GPIO_EN           0x20
+#define LED3_GPIO_EN           0x40
+#define LED4_GPIO_EN           0x80
+
+/* switch 1 port B */
+#define PUSHBUTTON1_EN         0x1
+#define PUSHBUTTON2_EN         0x2
+#define SD_CD_EN               0x4
+#define SD_WP_EN               0x8
+#define SPIFLASH_CS_EN         0x10
+#define SPI0D2_EN              0x20
+#define SPI0D3_EN              0x40
+
+/* switch 2 port A */
+#define PHYINT_EN              0x1
+#define PHY_PWR_DWN_INT        0x2
+#define PHYAD0                 0x4
+#define ETHERNET_EN            0x8
+#define WAKE_PUSHBUTTON_EN     0x10
+#define PD0_SPI0D2_EN          0x20
+#define PD1_SPI0D3_EN          0x40
+#define PD2_SPI0MISO_EN        0x80
+
+/* switch 2 port B */
+#define PD3_SPI0MOSI_EN        0x1
+#define PD4_SPI0CK_EN          0x2
+
+#ifdef CONFIG_BFIN_BOARD_VERSION_1_0
+#define SWITCH_ADDR     0x21
+#else
+#define SWITCH_ADDR     0x20
+#endif
+
+#define NUM_SWITCH      3
+#define IODIRA          0x0
+#define IODIRB          0x1
+#define OLATA           0x14
+#define OLATB           0x15
+
+int setup_board_switches(void);
+
+#endif /* __BOARD_SOFT_SWITCH_H__ */
diff --git a/common/Makefile b/common/Makefile
index 0e0fff1ffa..0429a3c51c 100644
--- a/common/Makefile
+++ b/common/Makefile
@@ -164,6 +164,7 @@ COBJS-$(CONFIG_CMD_SF) += cmd_sf.o
 COBJS-$(CONFIG_CMD_SCSI) += cmd_scsi.o
 COBJS-$(CONFIG_CMD_SHA1SUM) += cmd_sha1sum.o
 COBJS-$(CONFIG_CMD_SETEXPR) += cmd_setexpr.o
+COBJS-$(CONFIG_CMD_SOFTSWITCH) += cmd_softswitch.o
 COBJS-$(CONFIG_CMD_SPI) += cmd_spi.o
 COBJS-$(CONFIG_CMD_SPIBOOTLDR) += cmd_spibootldr.o
 COBJS-$(CONFIG_CMD_STRINGS) += cmd_strings.o
diff --git a/common/cmd_softswitch.c b/common/cmd_softswitch.c
new file mode 100644
index 0000000000..f75d926770
--- /dev/null
+++ b/common/cmd_softswitch.c
@@ -0,0 +1,41 @@
+/*
+ * cmd_softswitch.c - set the softswitch for bf60x
+ *
+ * Copyright (c) 2012 Analog Devices Inc.
+ *
+ * Licensed under the GPL-2 or later.
+ */
+
+#include <common.h>
+#include <command.h>
+#include <asm/blackfin.h>
+#include <asm/soft_switch.h>
+
+int do_softswitch(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
+{
+	int switchaddr, value, pin, port;
+
+	if (argc != 5)
+		return CMD_RET_USAGE;
+
+	if (strcmp(argv[2], "GPA") == 0)
+		port = IO_PORT_A;
+	else if (strcmp(argv[2], "GPB") == 0)
+		port = IO_PORT_B;
+	else
+		return CMD_RET_USAGE;
+
+	switchaddr = simple_strtoul(argv[1], NULL, 16);
+	pin = simple_strtoul(argv[3], NULL, 16);
+	value = simple_strtoul(argv[4], NULL, 16);
+
+	config_switch_bit(switchaddr, port, (1 << pin), IO_PORT_OUTPUT, value);
+
+	return 0;
+}
+
+U_BOOT_CMD(
+	softswitch_output, 5, 1, do_softswitch,
+	"switchaddr GPA/GPB pin_offset value",
+	""
+);
diff --git a/doc/README.watchdog b/doc/README.watchdog
index 33f31c2140..59f306b851 100644
--- a/doc/README.watchdog
+++ b/doc/README.watchdog
@@ -30,3 +30,6 @@ CONFIG_IMX_WATCHDOG
 
 CONFIG_XILINX_TB_WATCHDOG
 	Available for Xilinx Axi platforms to service timebase watchdog timer.
+
+CONFIG_BFIN_WATCHDOG
+	Available for bf5xx and bf6xx to service the watchdog.
diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
index 830e8e691a..f77c1ec1ef 100644
--- a/drivers/gpio/Makefile
+++ b/drivers/gpio/Makefile
@@ -48,6 +48,7 @@ COBJS-$(CONFIG_DB8500_GPIO)	+= db8500_gpio.o
 COBJS-$(CONFIG_BCM2835_GPIO)	+= bcm2835_gpio.o
 COBJS-$(CONFIG_S3C2440_GPIO)	+= s3c2440_gpio.o
 COBJS-$(CONFIG_XILINX_GPIO)	+= xilinx_gpio.o
+COBJS-$(CONFIG_ADI_GPIO2)	+= adi_gpio2.o
 
 COBJS	:= $(COBJS-y)
 SRCS 	:= $(COBJS:.o=.c)
diff --git a/drivers/gpio/adi_gpio2.c b/drivers/gpio/adi_gpio2.c
new file mode 100644
index 0000000000..7a034eba12
--- /dev/null
+++ b/drivers/gpio/adi_gpio2.c
@@ -0,0 +1,440 @@
+/*
+ * ADI GPIO2 Abstraction Layer
+ * Support BF54x, BF60x and future processors.
+ *
+ * Copyright 2008-2013 Analog Devices Inc.
+ *
+ * Licensed under the GPL-2 or later
+ */
+
+#include <common.h>
+#include <asm/errno.h>
+#include <asm/gpio.h>
+#include <asm/portmux.h>
+
+static struct gpio_port_t * const gpio_array[] = {
+	(struct gpio_port_t *)PORTA_FER,
+	(struct gpio_port_t *)PORTB_FER,
+	(struct gpio_port_t *)PORTC_FER,
+	(struct gpio_port_t *)PORTD_FER,
+	(struct gpio_port_t *)PORTE_FER,
+	(struct gpio_port_t *)PORTF_FER,
+	(struct gpio_port_t *)PORTG_FER,
+#if defined(CONFIG_BF54x)
+	(struct gpio_port_t *)PORTH_FER,
+	(struct gpio_port_t *)PORTI_FER,
+	(struct gpio_port_t *)PORTJ_FER,
+#endif
+};
+
+#define RESOURCE_LABEL_SIZE	16
+
+static struct str_ident {
+	char name[RESOURCE_LABEL_SIZE];
+} str_ident[MAX_RESOURCES];
+
+static void gpio_error(unsigned gpio)
+{
+	printf("adi_gpio2: GPIO %d wasn't requested!\n", gpio);
+}
+
+static void set_label(unsigned short ident, const char *label)
+{
+	if (label) {
+		strncpy(str_ident[ident].name, label,
+			RESOURCE_LABEL_SIZE);
+		str_ident[ident].name[RESOURCE_LABEL_SIZE - 1] = 0;
+	}
+}
+
+static char *get_label(unsigned short ident)
+{
+	return *str_ident[ident].name ? str_ident[ident].name : "UNKNOWN";
+}
+
+static int cmp_label(unsigned short ident, const char *label)
+{
+	if (label == NULL)
+		printf("adi_gpio2: please provide none-null label\n");
+
+	if (label)
+		return strcmp(str_ident[ident].name, label);
+	else
+		return -EINVAL;
+}
+
+#define map_entry(m, i)      reserved_##m##_map[gpio_bank(i)]
+#define is_reserved(m, i, e) (map_entry(m, i) & gpio_bit(i))
+#define reserve(m, i)        (map_entry(m, i) |= gpio_bit(i))
+#define unreserve(m, i)      (map_entry(m, i) &= ~gpio_bit(i))
+#define DECLARE_RESERVED_MAP(m, c) unsigned short reserved_##m##_map[c]
+
+static DECLARE_RESERVED_MAP(gpio, GPIO_BANK_NUM);
+static DECLARE_RESERVED_MAP(peri, gpio_bank(MAX_RESOURCES));
+
+inline int check_gpio(unsigned gpio)
+{
+#if defined(CONFIG_BF54x)
+	if (gpio == GPIO_PB15 || gpio == GPIO_PC14 || gpio == GPIO_PC15 ||
+		gpio == GPIO_PH14 || gpio == GPIO_PH15 ||
+		gpio == GPIO_PJ14 || gpio == GPIO_PJ15)
+		return -EINVAL;
+#endif
+	if (gpio >= MAX_GPIOS)
+		return -EINVAL;
+	return 0;
+}
+
+static void port_setup(unsigned gpio, unsigned short usage)
+{
+#if defined(CONFIG_BF54x)
+	if (usage == GPIO_USAGE)
+		gpio_array[gpio_bank(gpio)]->port_fer &= ~gpio_bit(gpio);
+	else
+		gpio_array[gpio_bank(gpio)]->port_fer |= gpio_bit(gpio);
+#else
+	if (usage == GPIO_USAGE)
+		gpio_array[gpio_bank(gpio)]->port_fer_clear = gpio_bit(gpio);
+	else
+		gpio_array[gpio_bank(gpio)]->port_fer_set = gpio_bit(gpio);
+#endif
+	SSYNC();
+}
+
+inline void portmux_setup(unsigned short per)
+{
+	u32 pmux;
+	u16 ident = P_IDENT(per);
+	u16 function = P_FUNCT2MUX(per);
+
+	pmux = gpio_array[gpio_bank(ident)]->port_mux;
+
+	pmux &= ~(0x3 << (2 * gpio_sub_n(ident)));
+	pmux |= (function & 0x3) << (2 * gpio_sub_n(ident));
+
+	gpio_array[gpio_bank(ident)]->port_mux = pmux;
+}
+
+inline u16 get_portmux(unsigned short per)
+{
+	u32 pmux;
+	u16 ident = P_IDENT(per);
+
+	pmux = gpio_array[gpio_bank(ident)]->port_mux;
+
+	return pmux >> (2 * gpio_sub_n(ident)) & 0x3;
+}
+
+unsigned short get_gpio_dir(unsigned gpio)
+{
+	return 0x01 &
+		(gpio_array[gpio_bank(gpio)]->dir_clear >> gpio_sub_n(gpio));
+}
+
+/***********************************************************
+*
+* FUNCTIONS:	Peripheral Resource Allocation
+*		and PortMux Setup
+*
+* INPUTS/OUTPUTS:
+* per	Peripheral Identifier
+* label	String
+*
+* DESCRIPTION: Peripheral Resource Allocation and Setup API
+**************************************************************/
+
+int peripheral_request(unsigned short per, const char *label)
+{
+	unsigned short ident = P_IDENT(per);
+
+	/*
+	 * Don't cares are pins with only one dedicated function
+	 */
+
+	if (per & P_DONTCARE)
+		return 0;
+
+	if (!(per & P_DEFINED))
+		return -ENODEV;
+
+	BUG_ON(ident >= MAX_RESOURCES);
+
+	/* If a pin can be muxed as either GPIO or peripheral, make
+	 * sure it is not already a GPIO pin when we request it.
+	 */
+	if (unlikely(!check_gpio(ident) && is_reserved(gpio, ident, 1))) {
+		printf("%s: Peripheral %d is already reserved as GPIO by %s!\n",
+		       __func__, ident, get_label(ident));
+		return -EBUSY;
+	}
+
+	if (unlikely(is_reserved(peri, ident, 1))) {
+		/*
+		 * Pin functions like AMC address strobes my
+		 * be requested and used by several drivers
+		 */
+
+		if (!((per & P_MAYSHARE) &&
+			get_portmux(per) == P_FUNCT2MUX(per))) {
+			/*
+			 * Allow that the identical pin function can
+			 * be requested from the same driver twice
+			 */
+
+			if (cmp_label(ident, label) == 0)
+				goto anyway;
+
+			printf("%s: Peripheral %d function %d is already "
+				"reserved by %s!\n", __func__, ident,
+				P_FUNCT2MUX(per), get_label(ident));
+			return -EBUSY;
+		}
+	}
+
+ anyway:
+	reserve(peri, ident);
+
+	portmux_setup(per);
+	port_setup(ident, PERIPHERAL_USAGE);
+
+	set_label(ident, label);
+
+	return 0;
+}
+
+int peripheral_request_list(const unsigned short per[], const char *label)
+{
+	u16 cnt;
+	int ret;
+
+	for (cnt = 0; per[cnt] != 0; cnt++) {
+		ret = peripheral_request(per[cnt], label);
+
+		if (ret < 0) {
+			for (; cnt > 0; cnt--)
+				peripheral_free(per[cnt - 1]);
+
+			return ret;
+		}
+	}
+
+	return 0;
+}
+
+void peripheral_free(unsigned short per)
+{
+	unsigned short ident = P_IDENT(per);
+
+	if (per & P_DONTCARE)
+		return;
+
+	if (!(per & P_DEFINED))
+		return;
+
+	if (unlikely(!is_reserved(peri, ident, 0)))
+		return;
+
+	if (!(per & P_MAYSHARE))
+		port_setup(ident, GPIO_USAGE);
+
+	unreserve(peri, ident);
+
+	set_label(ident, "free");
+}
+
+void peripheral_free_list(const unsigned short per[])
+{
+	u16 cnt;
+	for (cnt = 0; per[cnt] != 0; cnt++)
+		peripheral_free(per[cnt]);
+}
+
+/***********************************************************
+*
+* FUNCTIONS: GPIO Driver
+*
+* INPUTS/OUTPUTS:
+* gpio	PIO Number between 0 and MAX_GPIOS
+* label	String
+*
+* DESCRIPTION: GPIO Driver API
+**************************************************************/
+
+int gpio_request(unsigned gpio, const char *label)
+{
+	if (check_gpio(gpio) < 0)
+		return -EINVAL;
+
+	/*
+	 * Allow that the identical GPIO can
+	 * be requested from the same driver twice
+	 * Do nothing and return -
+	 */
+
+	if (cmp_label(gpio, label) == 0)
+		return 0;
+
+	if (unlikely(is_reserved(gpio, gpio, 1))) {
+		printf("adi_gpio2: GPIO %d is already reserved by %s!\n",
+			gpio, get_label(gpio));
+		return -EBUSY;
+	}
+	if (unlikely(is_reserved(peri, gpio, 1))) {
+		printf("adi_gpio2: GPIO %d is already reserved as Peripheral "
+			"by %s!\n", gpio, get_label(gpio));
+		return -EBUSY;
+	}
+
+	reserve(gpio, gpio);
+	set_label(gpio, label);
+
+	port_setup(gpio, GPIO_USAGE);
+
+	return 0;
+}
+
+int gpio_free(unsigned gpio)
+{
+	if (check_gpio(gpio) < 0)
+		return -1;
+
+	if (unlikely(!is_reserved(gpio, gpio, 0))) {
+		gpio_error(gpio);
+		return -1;
+	}
+
+	unreserve(gpio, gpio);
+
+	set_label(gpio, "free");
+
+	return 0;
+}
+
+#ifdef ADI_SPECIAL_GPIO_BANKS
+static DECLARE_RESERVED_MAP(special_gpio, gpio_bank(MAX_RESOURCES));
+
+int special_gpio_request(unsigned gpio, const char *label)
+{
+	/*
+	 * Allow that the identical GPIO can
+	 * be requested from the same driver twice
+	 * Do nothing and return -
+	 */
+
+	if (cmp_label(gpio, label) == 0)
+		return 0;
+
+	if (unlikely(is_reserved(special_gpio, gpio, 1))) {
+		printf("adi_gpio2: GPIO %d is already reserved by %s!\n",
+			gpio, get_label(gpio));
+		return -EBUSY;
+	}
+	if (unlikely(is_reserved(peri, gpio, 1))) {
+		printf("adi_gpio2: GPIO %d is already reserved as Peripheral "
+			"by %s!\n", gpio, get_label(gpio));
+
+		return -EBUSY;
+	}
+
+	reserve(special_gpio, gpio);
+	reserve(peri, gpio);
+
+	set_label(gpio, label);
+	port_setup(gpio, GPIO_USAGE);
+
+	return 0;
+}
+
+void special_gpio_free(unsigned gpio)
+{
+	if (unlikely(!is_reserved(special_gpio, gpio, 0))) {
+		gpio_error(gpio);
+		return;
+	}
+
+	reserve(special_gpio, gpio);
+	reserve(peri, gpio);
+	set_label(gpio, "free");
+}
+#endif
+
+static inline void __gpio_direction_input(unsigned gpio)
+{
+	gpio_array[gpio_bank(gpio)]->dir_clear = gpio_bit(gpio);
+#if defined(CONFIG_BF54x)
+	gpio_array[gpio_bank(gpio)]->inen |= gpio_bit(gpio);
+#else
+	gpio_array[gpio_bank(gpio)]->inen_set = gpio_bit(gpio);
+#endif
+}
+
+int gpio_direction_input(unsigned gpio)
+{
+	unsigned long flags;
+
+	if (!is_reserved(gpio, gpio, 0)) {
+		gpio_error(gpio);
+		return -EINVAL;
+	}
+
+	local_irq_save(flags);
+	__gpio_direction_input(gpio);
+	local_irq_restore(flags);
+
+	return 0;
+}
+
+int gpio_set_value(unsigned gpio, int arg)
+{
+	if (arg)
+		gpio_array[gpio_bank(gpio)]->data_set = gpio_bit(gpio);
+	else
+		gpio_array[gpio_bank(gpio)]->data_clear = gpio_bit(gpio);
+
+	return 0;
+}
+
+int gpio_direction_output(unsigned gpio, int value)
+{
+	unsigned long flags;
+
+	if (!is_reserved(gpio, gpio, 0)) {
+		gpio_error(gpio);
+		return -EINVAL;
+	}
+
+	local_irq_save(flags);
+
+#if defined(CONFIG_BF54x)
+	gpio_array[gpio_bank(gpio)]->inen &= ~gpio_bit(gpio);
+#else
+	gpio_array[gpio_bank(gpio)]->inen_clear = gpio_bit(gpio);
+#endif
+	gpio_set_value(gpio, value);
+	gpio_array[gpio_bank(gpio)]->dir_set = gpio_bit(gpio);
+
+	local_irq_restore(flags);
+
+	return 0;
+}
+
+int gpio_get_value(unsigned gpio)
+{
+	return 1 & (gpio_array[gpio_bank(gpio)]->data >> gpio_sub_n(gpio));
+}
+
+void gpio_labels(void)
+{
+	int c, gpio;
+
+	for (c = 0; c < MAX_RESOURCES; c++) {
+		gpio = is_reserved(gpio, c, 1);
+		if (!check_gpio(c) && gpio)
+			printf("GPIO_%d:\t%s\tGPIO %s\n", c, get_label(c),
+				get_gpio_dir(c) ? "OUTPUT" : "INPUT");
+		else if (is_reserved(peri, c, 1))
+			printf("GPIO_%d:\t%s\tPeripheral\n", c, get_label(c));
+		else
+			continue;
+	}
+}
diff --git a/drivers/net/bfin_mac.c b/drivers/net/bfin_mac.c
index c63398ebf8..0ffd59d497 100644
--- a/drivers/net/bfin_mac.c
+++ b/drivers/net/bfin_mac.c
@@ -122,8 +122,6 @@ static int bfin_EMAC_send(struct eth_device *dev, void *packet, int length)
 {
 	int i;
 	int result = 0;
-	unsigned int *buf;
-	buf = (unsigned int *)packet;
 
 	if (length <= 0) {
 		printf("Ethernet: bad packet size: %d\n", length);
diff --git a/drivers/serial/Makefile b/drivers/serial/Makefile
index fbc4e97e98..442b7ea0df 100644
--- a/drivers/serial/Makefile
+++ b/drivers/serial/Makefile
@@ -52,6 +52,7 @@ COBJS-$(CONFIG_XILINX_UARTLITE) += serial_xuartlite.o
 COBJS-$(CONFIG_SANDBOX_SERIAL) += sandbox.o
 COBJS-$(CONFIG_SCIF_CONSOLE) += serial_sh.o
 COBJS-$(CONFIG_ZYNQ_SERIAL) += serial_zynq.o
+COBJS-$(CONFIG_BFIN_SERIAL) += serial_bfin.o
 
 ifndef CONFIG_SPL_BUILD
 COBJS-$(CONFIG_USB_TTY) += usbtty.o
diff --git a/arch/blackfin/cpu/serial.c b/drivers/serial/serial_bfin.c
index 9847e9f2c5..0443b8427a 100644
--- a/arch/blackfin/cpu/serial.c
+++ b/drivers/serial/serial_bfin.c
@@ -43,13 +43,12 @@
 #include <serial.h>
 #include <linux/compiler.h>
 #include <asm/blackfin.h>
+#include <asm/serial.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
 #ifdef CONFIG_UART_CONSOLE
 
-#include "serial.h"
-
 #ifdef CONFIG_DEBUG_SERIAL
 static uart_lsr_t cached_lsr[256];
 static uart_lsr_t cached_rbr[256];
@@ -195,7 +194,18 @@ static void uart_loop(uint32_t uart_base, int state)
 
 #endif
 
-#ifdef CONFIG_SYS_BFIN_UART
+static inline void __serial_set_baud(uint32_t uart_base, uint32_t baud)
+{
+#ifdef CONFIG_DEBUG_EARLY_SERIAL
+	serial_early_set_baud(uart_base, baud);
+#else
+	uint16_t divisor = (get_uart_clk() + (baud * 8)) / (baud * 16)
+			- ANOMALY_05000230;
+
+	/* Program the divisor to get the baud rate we want */
+	serial_set_divisor(uart_base, divisor);
+#endif
+}
 
 static void uart_puts(uint32_t uart_base, const char *s)
 {
@@ -209,7 +219,7 @@ static int uart##n##_init(void) \
 	const unsigned short pins[] = { _P_UART(n, RX), _P_UART(n, TX), 0, }; \
 	peripheral_request_list(pins, "bfin-uart"); \
 	uart_init(MMR_UART(n)); \
-	serial_early_set_baud(MMR_UART(n), gd->baudrate); \
+	__serial_set_baud(MMR_UART(n), gd->baudrate); \
 	uart_lsr_clear(MMR_UART(n)); \
 	return 0; \
 } \
@@ -221,7 +231,7 @@ static int uart##n##_uninit(void) \
 \
 static void uart##n##_setbrg(void) \
 { \
-	serial_early_set_baud(MMR_UART(n), gd->baudrate); \
+	__serial_set_baud(MMR_UART(n), gd->baudrate); \
 } \
 \
 static int uart##n##_getc(void) \
@@ -305,65 +315,97 @@ void bfin_serial_initialize(void)
 #endif
 }
 
-#else
+#ifdef CONFIG_DEBUG_EARLY_SERIAL
+inline void uart_early_putc(uint32_t uart_base, const char c)
+{
+	/* send a \r for compatibility */
+	if (c == '\n')
+		uart_early_putc(uart_base, '\r');
 
-/* Symbol for our assembly to call. */
-void serial_set_baud(uint32_t baud)
+	/* wait for the hardware fifo to clear up */
+	while (!(_lsr_read(pUART) & THRE))
+		continue;
+
+	/* queue the character for transmission */
+	bfin_write(&pUART->thr, c);
+	SSYNC();
+}
+
+void uart_early_puts(const char *s)
 {
-	serial_early_set_baud(UART_BASE, baud);
+	while (*s)
+		uart_early_putc(UART_BASE, *s++);
 }
 
-/* Symbol for common u-boot code to call.
- * Setup the baudrate (brg: baudrate generator).
- */
-void serial_setbrg(void)
+/* Symbol for our assembly to call. */
+void _serial_early_set_baud(uint32_t baud)
 {
-	serial_set_baud(gd->baudrate);
+	serial_early_set_baud(UART_BASE, baud);
 }
 
 /* Symbol for our assembly to call. */
-void serial_initialize(void)
+void _serial_early_init(void)
 {
 	serial_early_init(UART_BASE);
 }
+#endif
 
-/* Symbol for common u-boot code to call. */
-int serial_init(void)
+#elif defined(CONFIG_UART_MEM)
+
+char serial_logbuf[CONFIG_UART_MEM];
+char *serial_logbuf_head = serial_logbuf;
+
+int serial_mem_init(void)
 {
-	serial_initialize();
-	serial_setbrg();
-	uart_lsr_clear(UART_BASE);
+	serial_logbuf_head = serial_logbuf;
 	return 0;
 }
 
-int serial_tstc(void)
+void serial_mem_setbrg(void)
 {
-	return uart_tstc(UART_BASE);
 }
 
-int serial_getc(void)
+int serial_mem_tstc(void)
 {
-	return uart_getc(UART_BASE);
+	return 0;
 }
 
-void serial_putc(const char c)
+int serial_mem_getc(void)
 {
-	uart_putc(UART_BASE, c);
+	return 0;
 }
 
-void serial_puts(const char *s)
+void serial_mem_putc(const char c)
+{
+	*serial_logbuf_head = c;
+	if (++serial_logbuf_head == serial_logbuf + CONFIG_UART_MEM)
+		serial_logbuf_head = serial_logbuf;
+}
+
+void serial_mem_puts(const char *s)
 {
 	while (*s)
 		serial_putc(*s++);
 }
 
-LOOP(
-void serial_loop(int state)
+struct serial_device bfin_serial_mem_device = {
+	.name   = "bfin_uart_mem",
+	.start  = serial_mem_init,
+	.setbrg = serial_mem_setbrg,
+	.getc   = serial_mem_getc,
+	.tstc   = serial_mem_tstc,
+	.putc   = serial_mem_putc,
+	.puts   = serial_mem_puts,
+};
+
+
+__weak struct serial_device *default_serial_console(void)
 {
-	uart_loop(UART_BASE, state);
+	return &bfin_serial_mem_device;
 }
-)
 
-#endif
-
-#endif
+void bfin_serial_initialize(void)
+{
+	serial_register(&bfin_serial_mem_device);
+}
+#endif /* CONFIG_UART_MEM */
diff --git a/drivers/spi/bfin_spi.c b/drivers/spi/bfin_spi.c
index ab2e8b998b..a9a4d92c3e 100644
--- a/drivers/spi/bfin_spi.c
+++ b/drivers/spi/bfin_spi.c
@@ -13,7 +13,6 @@
 #include <spi.h>
 
 #include <asm/blackfin.h>
-#include <asm/dma.h>
 #include <asm/gpio.h>
 #include <asm/portmux.h>
 #include <asm/mach-common/bits/spi.h>
@@ -242,109 +241,15 @@ void spi_release_bus(struct spi_slave *slave)
 	SSYNC();
 }
 
-#ifdef __ADSPBF54x__
-# define SPI_DMA_BASE DMA4_NEXT_DESC_PTR
-#elif defined(__ADSPBF533__) || defined(__ADSPBF532__) || defined(__ADSPBF531__) || \
-      defined(__ADSPBF538__) || defined(__ADSPBF539__)
-# define SPI_DMA_BASE DMA5_NEXT_DESC_PTR
-#elif defined(__ADSPBF561__)
-# define SPI_DMA_BASE DMA2_4_NEXT_DESC_PTR
-#elif defined(__ADSPBF537__) || defined(__ADSPBF536__) || defined(__ADSPBF534__) || \
-      defined(__ADSPBF52x__) || defined(__ADSPBF51x__)
-# define SPI_DMA_BASE DMA7_NEXT_DESC_PTR
-# elif defined(__ADSPBF50x__)
-# define SPI_DMA_BASE DMA6_NEXT_DESC_PTR
-#else
-# error "Please provide SPI DMA channel defines"
-#endif
-static volatile struct dma_register *dma = (void *)SPI_DMA_BASE;
-
 #ifndef CONFIG_BFIN_SPI_IDLE_VAL
 # define CONFIG_BFIN_SPI_IDLE_VAL 0xff
 #endif
 
-#ifdef CONFIG_BFIN_SPI_NO_DMA
-# define SPI_DMA 0
-#else
-# define SPI_DMA 1
-#endif
-
-static int spi_dma_xfer(struct bfin_spi_slave *bss, const u8 *tx, u8 *rx,
-			uint bytes)
-{
-	int ret = -1;
-	u16 ndsize, spi_config, dma_config;
-	struct dmasg dmasg[2];
-	const u8 *buf;
-
-	if (tx) {
-		debug("%s: doing half duplex TX\n", __func__);
-		buf = tx;
-		spi_config = TDBR_DMA;
-		dma_config = 0;
-	} else {
-		debug("%s: doing half duplex RX\n", __func__);
-		buf = rx;
-		spi_config = RDBR_DMA;
-		dma_config = WNR;
-	}
-
-	dmasg[0].start_addr = (unsigned long)buf;
-	dmasg[0].x_modify = 1;
-	dma_config |= WDSIZE_8 | DMAEN;
-	if (bytes <= 65536) {
-		blackfin_dcache_flush_invalidate_range(buf, buf + bytes);
-		ndsize = NDSIZE_5;
-		dmasg[0].cfg = NDSIZE_0 | dma_config | FLOW_STOP | DI_EN;
-		dmasg[0].x_count = bytes;
-	} else {
-		blackfin_dcache_flush_invalidate_range(buf, buf + 65536 - 1);
-		ndsize = NDSIZE_7;
-		dmasg[0].cfg = NDSIZE_5 | dma_config | FLOW_ARRAY | DMA2D;
-		dmasg[0].x_count = 0;	/* 2^16 */
-		dmasg[0].y_count = bytes >> 16;	/* count / 2^16 */
-		dmasg[0].y_modify = 1;
-		dmasg[1].start_addr = (unsigned long)(buf + (bytes & ~0xFFFF));
-		dmasg[1].cfg = NDSIZE_0 | dma_config | FLOW_STOP | DI_EN;
-		dmasg[1].x_count = bytes & 0xFFFF; /* count % 2^16 */
-		dmasg[1].x_modify = 1;
-	}
-
-	dma->cfg = 0;
-	dma->irq_status = DMA_DONE | DMA_ERR;
-	dma->curr_desc_ptr = dmasg;
-	write_SPI_CTL(bss, (bss->ctl & ~TDBR_CORE));
-	write_SPI_STAT(bss, -1);
-	SSYNC();
-
-	write_SPI_TDBR(bss, CONFIG_BFIN_SPI_IDLE_VAL);
-	dma->cfg = ndsize | FLOW_ARRAY | DMAEN;
-	write_SPI_CTL(bss, (bss->ctl & ~TDBR_CORE) | spi_config);
-	SSYNC();
-
-	/*
-	 * We already invalidated the first 64k,
-	 * now while we just wait invalidate the remaining part.
-	 * Its not likely that the DMA is going to overtake
-	 */
-	if (bytes > 65536)
-		blackfin_dcache_flush_invalidate_range(buf + 65536, buf + bytes);
-
-	while (!(dma->irq_status & DMA_DONE))
-		if (ctrlc())
-			goto done;
-
-	dma->cfg = 0;
-
-	ret = 0;
- done:
-	write_SPI_CTL(bss, bss->ctl);
-	return ret;
-}
-
 static int spi_pio_xfer(struct bfin_spi_slave *bss, const u8 *tx, u8 *rx,
 			uint bytes)
 {
+	/* discard invalid data and clear RXS */
+	read_SPI_RDBR(bss);
 	/* todo: take advantage of hardware fifos  */
 	while (bytes--) {
 		u8 value = (tx ? *tx++ : CONFIG_BFIN_SPI_IDLE_VAL);
@@ -393,11 +298,7 @@ int spi_xfer(struct spi_slave *slave, unsigned int bitlen, const void *dout,
 	if (flags & SPI_XFER_BEGIN)
 		spi_cs_activate(slave);
 
-	/* TX DMA doesn't work quite right */
-	if (SPI_DMA && bytes > 6 && (!tx /*|| !rx*/))
-		ret = spi_dma_xfer(bss, tx, rx, bytes);
-	else
-		ret = spi_pio_xfer(bss, tx, rx, bytes);
+	ret = spi_pio_xfer(bss, tx, rx, bytes);
 
  done:
 	if (flags & SPI_XFER_END)
diff --git a/drivers/watchdog/Makefile b/drivers/watchdog/Makefile
index 13e7c37686..d57578df6c 100644
--- a/drivers/watchdog/Makefile
+++ b/drivers/watchdog/Makefile
@@ -33,6 +33,7 @@ endif
 COBJS-$(CONFIG_TNETV107X_WATCHDOG) += tnetv107x_wdt.o
 COBJS-$(CONFIG_S5P)               += s5p_wdt.o
 COBJS-$(CONFIG_XILINX_TB_WATCHDOG) += xilinx_tb_wdt.o
+COBJS-$(CONFIG_BFIN_WATCHDOG)  += bfin_wdt.o
 
 COBJS	:= $(COBJS-y)
 SRCS	:= $(COBJS:.o=.c)
diff --git a/arch/blackfin/cpu/watchdog.c b/drivers/watchdog/bfin_wdt.c
index 1886bda0ae..7a6756b2e5 100644
--- a/arch/blackfin/cpu/watchdog.c
+++ b/drivers/watchdog/bfin_wdt.c
@@ -9,6 +9,7 @@
 #include <common.h>
 #include <watchdog.h>
 #include <asm/blackfin.h>
+#include <asm/mach-common/bits/watchdog.h>
 
 void hw_watchdog_reset(void)
 {
@@ -17,7 +18,9 @@ void hw_watchdog_reset(void)
 
 void hw_watchdog_init(void)
 {
-	bfin_write_WDOG_CNT(5 * get_sclk());	/* 5 second timeout */
+	bfin_write_WDOG_CTL(WDDIS);
+	SSYNC();
+	bfin_write_WDOG_CNT(CONFIG_WATCHDOG_TIMEOUT_MSECS / 1000 * get_sclk());
 	hw_watchdog_reset();
-	bfin_write_WDOG_CTL(0x0);
+	bfin_write_WDOG_CTL(WDEN);
 }
diff --git a/include/configs/bf527-ezkit.h b/include/configs/bf527-ezkit.h
index 7b51b53dc5..db1b6136f3 100644
--- a/include/configs/bf527-ezkit.h
+++ b/include/configs/bf527-ezkit.h
@@ -149,10 +149,15 @@
 #define CONFIG_MUSB_TIMEOUT 100000
 #endif
 
+/* Don't waste time transferring a logo over the UART */
+#if (CONFIG_BFIN_BOOT_MODE != BFIN_BOOT_UART)
+/*# define CONFIG_VIDEO*/
+#endif
 
 /*
  * Video Settings
  */
+#ifdef CONFIG_VIDEO
 #ifdef CONFIG_BF527_EZKIT_REV_2_1
 # define CONFIG_LQ035Q1_SPI_BUS	0
 # define CONFIG_LQ035Q1_SPI_CS	7
@@ -166,7 +171,7 @@
 #else
 # define EASYLOGO_HEADER <asm/bfin_logo_230x230_lzma.h>
 #endif
-
+#endif /* CONFIG_VIDEO */
 
 /*
  * Misc Settings
@@ -175,11 +180,6 @@
 #define CONFIG_RTC_BFIN
 #define CONFIG_UART_CONSOLE	1
 
-/* Don't waste time transferring a logo over the UART */
-#if (CONFIG_BFIN_BOOT_MODE != BFIN_BOOT_UART)
-# define CONFIG_VIDEO
-#endif
-
 
 /*
  * Pull in common ADI header for remaining command/environment setup
diff --git a/include/configs/bf537-stamp.h b/include/configs/bf537-stamp.h
index 05029d497b..25cebf880f 100644
--- a/include/configs/bf537-stamp.h
+++ b/include/configs/bf537-stamp.h
@@ -52,7 +52,7 @@
 #define CONFIG_EBIU_AMBCTL0_VAL	0x7BB07BB0
 #define CONFIG_EBIU_AMBCTL1_VAL	0xFFC27BB0
 
-#define CONFIG_SYS_MONITOR_LEN		(512 * 1024)
+#define CONFIG_SYS_MONITOR_LEN		(768 * 1024)
 #define CONFIG_SYS_MALLOC_LEN		(384 * 1024)
 
 
@@ -135,15 +135,17 @@
 /*
  * SPI_MMC Settings
  */
+#define CONFIG_MMC_SPI
+#ifdef CONFIG_MMC_SPI
 #define CONFIG_MMC
 #define CONFIG_GENERIC_MMC
-#define CONFIG_MMC_SPI
-
+#endif
 
 /*
  * NAND Settings
  */
 /* #define CONFIG_NAND_PLAT */
+#ifdef CONFIG_NAND_PLAT
 #define CONFIG_SYS_NAND_BASE		0x20212000
 #define CONFIG_SYS_MAX_NAND_DEVICE	1
 
@@ -158,7 +160,7 @@
 #define NAND_PLAT_WRITE_CMD(chip, cmd) BFIN_NAND_WRITE(BFIN_NAND_CLE(chip), cmd)
 #define NAND_PLAT_WRITE_ADR(chip, cmd) BFIN_NAND_WRITE(BFIN_NAND_ALE(chip), cmd)
 #define NAND_PLAT_GPIO_DEV_READY       GPIO_PF3
-
+#endif /* CONFIG_NAND_PLAT */
 
 /*
  * CF-CARD IDE-HDD Support
diff --git a/include/configs/bf548-ezkit.h b/include/configs/bf548-ezkit.h
index e6b05db09d..da5f029435 100644
--- a/include/configs/bf548-ezkit.h
+++ b/include/configs/bf548-ezkit.h
@@ -120,18 +120,16 @@
 #define CONFIG_ENV_SECT_SIZE	0x8000
 #endif
 
-
 /*
  * NAND Settings
  */
-#define CONFIG_BFIN_NFC_CTL_VAL	0x0033
 #if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_NAND)
-# define CONFIG_BFIN_NFC_BOOTROM_ECC
-#endif
+#define CONFIG_BFIN_NFC_CTL_VAL        0x0033
+#define CONFIG_BFIN_NFC_BOOTROM_ECC
 #define CONFIG_DRIVER_NAND_BFIN
-#define CONFIG_SYS_NAND_BASE		0 /* not actually used */
-#define CONFIG_SYS_MAX_NAND_DEVICE	1
-
+#define CONFIG_SYS_NAND_BASE           0 /* not actually used */
+#define CONFIG_SYS_MAX_NAND_DEVICE     1
+#endif
 
 /*
  * I2C Settings
@@ -184,13 +182,12 @@
 #define CONFIG_UART_CONSOLE	1
 #define CONFIG_BFIN_SPI_IMG_SIZE 0x50000
 
-#ifndef __ADSPBF542__
-/* Don't waste time transferring a logo over the UART */
-# if (CONFIG_BFIN_BOOT_MODE != BFIN_BOOT_UART)
-#  define CONFIG_VIDEO
-#  define EASYLOGO_HEADER <asm/bfin_logo_230x230_gzip.h>
-# endif
-# define CONFIG_DEB_DMA_URGENT
+#define CONFIG_ADI_GPIO2
+
+#undef CONFIG_VIDEO
+#ifdef CONFIG_VIDEO
+#define EASYLOGO_HEADER < asm/bfin_logo_230x230_gzip.h >
+#define CONFIG_DEB_DMA_URGENT
 #endif
 
 /* Define if want to do post memory test */
diff --git a/include/configs/bf561-ezkit.h b/include/configs/bf561-ezkit.h
index 1a9d27ea2a..6ee1e4c869 100644
--- a/include/configs/bf561-ezkit.h
+++ b/include/configs/bf561-ezkit.h
@@ -98,6 +98,11 @@
  */
 #define CONFIG_UART_CONSOLE	0
 
+/*
+ * Run core 1 from L1 SRAM start address when init uboot on core 0
+ */
+/* #define CONFIG_CORE1_RUN	1 */
+
 
 /*
  * Pull in common ADI header for remaining command/environment setup
diff --git a/include/configs/bf609-ezkit.h b/include/configs/bf609-ezkit.h
index 02149fa94d..1a43e1b433 100644
--- a/include/configs/bf609-ezkit.h
+++ b/include/configs/bf609-ezkit.h
@@ -144,10 +144,13 @@
 #define CONFIG_UART_CONSOLE	0
 
 #define CONFIG_CMD_MEMORY
+#define CONFIG_CMD_SOFTSWITCH
 
 #define CONFIG_SYS_MEMTEST_END (CONFIG_STACKBASE - 20*1024*1024 + 4)
 #define CONFIG_BFIN_SOFT_SWITCH
 
+#define CONFIG_ADI_GPIO2
+
 #if 0
 #define CONFIG_UART_MEM 1024
 #undef CONFIG_UART_CONSOLE
@@ -155,6 +158,13 @@
 #undef CONFIG_UART_CONSOLE_IS_JTAG
 #endif
 
+#define CONFIG_BOARD_SIZE_LIMIT $$((512 * 1024))
+
+/*
+ * Run core 1 from L1 SRAM start address when init uboot on core 0
+ */
+/* #define CONFIG_CORE1_RUN	1 */
+
 /*
  * Pull in common ADI header for remaining command/environment setup
  */
diff --git a/include/configs/bfin_adi_common.h b/include/configs/bfin_adi_common.h
index d3ae3a71cd..e1a6fe3056 100644
--- a/include/configs/bfin_adi_common.h
+++ b/include/configs/bfin_adi_common.h
@@ -111,8 +111,8 @@
 #ifndef CONFIG_BAUDRATE
 # define CONFIG_BAUDRATE	57600
 #endif
-#ifndef CONFIG_DEBUG_EARLY_SERIAL
-# define CONFIG_SYS_BFIN_UART
+#ifdef CONFIG_UART_CONSOLE
+# define CONFIG_BFIN_SERIAL
 #endif
 
 /*
@@ -317,5 +317,13 @@
 #define CONFIG_BFIN_SPI_GPIO_CS /* Only matters if BFIN_SPI is enabled */
 #define CONFIG_LZMA
 #define CONFIG_MONITOR_IS_IN_RAM
-
+#ifdef CONFIG_HW_WATCHDOG
+# define CONFIG_BFIN_WATCHDOG
+# ifndef CONFIG_WATCHDOG_TIMEOUT_MSECS
+#  define CONFIG_WATCHDOG_TIMEOUT_MSECS 5000
+# endif
+#endif
+#ifndef CONFIG_ADI_GPIO2
+# define CONFIG_ADI_GPIO1
+#endif
 #endif
diff --git a/include/watchdog.h b/include/watchdog.h
index 97ec186be3..d95e4b164d 100644
--- a/include/watchdog.h
+++ b/include/watchdog.h
@@ -108,8 +108,7 @@ int init_func_watchdog_reset(void);
 	void reset_4xx_watchdog(void);
 #endif
 
-/* Freescale i.MX */
-#if defined(CONFIG_IMX_WATCHDOG) && !defined(__ASSEMBLY__)
+#if defined(CONFIG_HW_WATCHDOG) && !defined(__ASSEMBLY__)
 	void hw_watchdog_init(void);
 #endif
 #endif /* _WATCHDOG_H_ */