i2c: fti2c010: remove unused/unmaintained driver

CONFIG_SYS_I2C_FTI2C010 is not enabled by anyone.

Commit 2852709676c8 ("dm: i2c: Add a note to I2C drivers which need
conversion") prompted to convert this driver to DM before June 2017,
but not converted yet.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Heiko Schocher <hs@denx.de>

3 files changed, 0 insertions, 421 deletions

diff --git a/drivers/i2c/Makefile b/drivers/i2c/Makefile
index 121e4e2990..3a8c61b485 100644
--- a/drivers/i2c/Makefile
+++ b/drivers/i2c/Makefile
@@ -20,7 +20,6 @@ obj-$(CONFIG_SYS_I2C_CADENCE) += i2c-cdns.o
 obj-$(CONFIG_SYS_I2C_DAVINCI) += davinci_i2c.o
 obj-$(CONFIG_SYS_I2C_DW) += designware_i2c.o
 obj-$(CONFIG_SYS_I2C_FSL) += fsl_i2c.o
-obj-$(CONFIG_SYS_I2C_FTI2C010) += fti2c010.o
 obj-$(CONFIG_SYS_I2C_IHS) += ihs_i2c.o
 obj-$(CONFIG_SYS_I2C_INTEL) += intel_i2c.o
 obj-$(CONFIG_SYS_I2C_IMX_LPI2C) += imx_lpi2c.o
diff --git a/drivers/i2c/fti2c010.c b/drivers/i2c/fti2c010.c
deleted file mode 100644
index 4da959fa53..0000000000
--- a/drivers/i2c/fti2c010.c
+++ /dev/null
@@ -1,340 +0,0 @@
-/*
- * Faraday I2C Controller
- *
- * (C) Copyright 2010 Faraday Technology
- * Dante Su <dantesu@faraday-tech.com>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- *
- * NOTE: This driver should be converted to driver model before June 2017.
- * Please see doc/driver-model/i2c-howto.txt for instructions.
- */
-
-#include <common.h>
-#include <asm/io.h>
-#include <i2c.h>
-
-#include "fti2c010.h"
-
-#ifndef CONFIG_SYS_I2C_SPEED
-#define CONFIG_SYS_I2C_SPEED    5000
-#endif
-
-#ifndef CONFIG_SYS_I2C_SLAVE
-#define CONFIG_SYS_I2C_SLAVE    0
-#endif
-
-#ifndef CONFIG_FTI2C010_CLOCK
-#define CONFIG_FTI2C010_CLOCK   clk_get_rate("I2C")
-#endif
-
-#ifndef CONFIG_FTI2C010_TIMEOUT
-#define CONFIG_FTI2C010_TIMEOUT 10 /* ms */
-#endif
-
-/* 7-bit dev address + 1-bit read/write */
-#define I2C_RD(dev)             ((((dev) << 1) & 0xfe) | 1)
-#define I2C_WR(dev)             (((dev) << 1) & 0xfe)
-
-struct fti2c010_chip {
-	struct fti2c010_regs *regs;
-};
-
-static struct fti2c010_chip chip_list[] = {
-	{
-		.regs = (struct fti2c010_regs *)CONFIG_FTI2C010_BASE,
-	},
-#ifdef CONFIG_FTI2C010_BASE1
-	{
-		.regs = (struct fti2c010_regs *)CONFIG_FTI2C010_BASE1,
-	},
-#endif
-#ifdef CONFIG_FTI2C010_BASE2
-	{
-		.regs = (struct fti2c010_regs *)CONFIG_FTI2C010_BASE2,
-	},
-#endif
-#ifdef CONFIG_FTI2C010_BASE3
-	{
-		.regs = (struct fti2c010_regs *)CONFIG_FTI2C010_BASE3,
-	},
-#endif
-};
-
-static int fti2c010_reset(struct fti2c010_chip *chip)
-{
-	ulong ts;
-	int ret = -1;
-	struct fti2c010_regs *regs = chip->regs;
-
-	writel(CR_I2CRST, &regs->cr);
-	for (ts = get_timer(0); get_timer(ts) < CONFIG_FTI2C010_TIMEOUT; ) {
-		if (!(readl(&regs->cr) & CR_I2CRST)) {
-			ret = 0;
-			break;
-		}
-	}
-
-	if (ret)
-		printf("fti2c010: reset timeout\n");
-
-	return ret;
-}
-
-static int fti2c010_wait(struct fti2c010_chip *chip, uint32_t mask)
-{
-	int ret = -1;
-	uint32_t stat, ts;
-	struct fti2c010_regs *regs = chip->regs;
-
-	for (ts = get_timer(0); get_timer(ts) < CONFIG_FTI2C010_TIMEOUT; ) {
-		stat = readl(&regs->sr);
-		if ((stat & mask) == mask) {
-			ret = 0;
-			break;
-		}
-	}
-
-	return ret;
-}
-
-static unsigned int set_i2c_bus_speed(struct fti2c010_chip *chip,
-	unsigned int speed)
-{
-	struct fti2c010_regs *regs = chip->regs;
-	unsigned int clk = CONFIG_FTI2C010_CLOCK;
-	unsigned int gsr = 0;
-	unsigned int tsr = 32;
-	unsigned int div, rate;
-
-	for (div = 0; div < 0x3ffff; ++div) {
-		/* SCLout = PCLK/(2*(COUNT + 2) + GSR) */
-		rate = clk / (2 * (div + 2) + gsr);
-		if (rate <= speed)
-			break;
-	}
-
-	writel(TGSR_GSR(gsr) | TGSR_TSR(tsr), &regs->tgsr);
-	writel(CDR_DIV(div), &regs->cdr);
-
-	return rate;
-}
-
-/*
- * Initialization, must be called once on start up, may be called
- * repeatedly to change the speed and slave addresses.
- */
-static void fti2c010_init(struct i2c_adapter *adap, int speed, int slaveaddr)
-{
-	struct fti2c010_chip *chip = chip_list + adap->hwadapnr;
-
-	if (adap->init_done)
-		return;
-
-#ifdef CONFIG_SYS_I2C_INIT_BOARD
-	/* Call board specific i2c bus reset routine before accessing the
-	 * environment, which might be in a chip on that bus. For details
-	 * about this problem see doc/I2C_Edge_Conditions.
-	*/
-	i2c_init_board();
-#endif
-
-	/* master init */
-
-	fti2c010_reset(chip);
-
-	set_i2c_bus_speed(chip, speed);
-
-	/* slave init, don't care */
-}
-
-/*
- * Probe the given I2C chip address.  Returns 0 if a chip responded,
- * not 0 on failure.
- */
-static int fti2c010_probe(struct i2c_adapter *adap, u8 dev)
-{
-	struct fti2c010_chip *chip = chip_list + adap->hwadapnr;
-	struct fti2c010_regs *regs = chip->regs;
-	int ret;
-
-	/* 1. Select slave device (7bits Address + 1bit R/W) */
-	writel(I2C_WR(dev), &regs->dr);
-	writel(CR_ENABLE | CR_TBEN | CR_START, &regs->cr);
-	ret = fti2c010_wait(chip, SR_DT);
-	if (ret)
-		return ret;
-
-	/* 2. Select device register */
-	writel(0, &regs->dr);
-	writel(CR_ENABLE | CR_TBEN, &regs->cr);
-	ret = fti2c010_wait(chip, SR_DT);
-
-	return ret;
-}
-
-static void to_i2c_addr(u8 *buf, uint32_t addr, int alen)
-{
-	int i, shift;
-
-	if (!buf || alen <= 0)
-		return;
-
-	/* MSB first */
-	i = 0;
-	shift = (alen - 1) * 8;
-	while (alen-- > 0) {
-		buf[i] = (u8)(addr >> shift);
-		shift -= 8;
-	}
-}
-
-static int fti2c010_read(struct i2c_adapter *adap,
-			u8 dev, uint addr, int alen, uchar *buf, int len)
-{
-	struct fti2c010_chip *chip = chip_list + adap->hwadapnr;
-	struct fti2c010_regs *regs = chip->regs;
-	int ret, pos;
-	uchar paddr[4] = { 0 };
-
-	to_i2c_addr(paddr, addr, alen);
-
-	/*
-	 * Phase A. Set register address
-	 */
-
-	/* A.1 Select slave device (7bits Address + 1bit R/W) */
-	writel(I2C_WR(dev), &regs->dr);
-	writel(CR_ENABLE | CR_TBEN | CR_START, &regs->cr);
-	ret = fti2c010_wait(chip, SR_DT);
-	if (ret)
-		return ret;
-
-	/* A.2 Select device register */
-	for (pos = 0; pos < alen; ++pos) {
-		uint32_t ctrl = CR_ENABLE | CR_TBEN;
-
-		writel(paddr[pos], &regs->dr);
-		writel(ctrl, &regs->cr);
-		ret = fti2c010_wait(chip, SR_DT);
-		if (ret)
-			return ret;
-	}
-
-	/*
-	 * Phase B. Get register data
-	 */
-
-	/* B.1 Select slave device (7bits Address + 1bit R/W) */
-	writel(I2C_RD(dev), &regs->dr);
-	writel(CR_ENABLE | CR_TBEN | CR_START, &regs->cr);
-	ret = fti2c010_wait(chip, SR_DT);
-	if (ret)
-		return ret;
-
-	/* B.2 Get register data */
-	for (pos = 0; pos < len; ++pos) {
-		uint32_t ctrl = CR_ENABLE | CR_TBEN;
-		uint32_t stat = SR_DR;
-
-		if (pos == len - 1) {
-			ctrl |= CR_NAK | CR_STOP;
-			stat |= SR_ACK;
-		}
-		writel(ctrl, &regs->cr);
-		ret = fti2c010_wait(chip, stat);
-		if (ret)
-			break;
-		buf[pos] = (uchar)(readl(&regs->dr) & 0xFF);
-	}
-
-	return ret;
-}
-
-static int fti2c010_write(struct i2c_adapter *adap,
-			u8 dev, uint addr, int alen, u8 *buf, int len)
-{
-	struct fti2c010_chip *chip = chip_list + adap->hwadapnr;
-	struct fti2c010_regs *regs = chip->regs;
-	int ret, pos;
-	uchar paddr[4] = { 0 };
-
-	to_i2c_addr(paddr, addr, alen);
-
-	/*
-	 * Phase A. Set register address
-	 *
-	 * A.1 Select slave device (7bits Address + 1bit R/W)
-	 */
-	writel(I2C_WR(dev), &regs->dr);
-	writel(CR_ENABLE | CR_TBEN | CR_START, &regs->cr);
-	ret = fti2c010_wait(chip, SR_DT);
-	if (ret)
-		return ret;
-
-	/* A.2 Select device register */
-	for (pos = 0; pos < alen; ++pos) {
-		uint32_t ctrl = CR_ENABLE | CR_TBEN;
-
-		writel(paddr[pos], &regs->dr);
-		writel(ctrl, &regs->cr);
-		ret = fti2c010_wait(chip, SR_DT);
-		if (ret)
-			return ret;
-	}
-
-	/*
-	 * Phase B. Set register data
-	 */
-	for (pos = 0; pos < len; ++pos) {
-		uint32_t ctrl = CR_ENABLE | CR_TBEN;
-
-		if (pos == len - 1)
-			ctrl |= CR_STOP;
-		writel(buf[pos], &regs->dr);
-		writel(ctrl, &regs->cr);
-		ret = fti2c010_wait(chip, SR_DT);
-		if (ret)
-			break;
-	}
-
-	return ret;
-}
-
-static unsigned int fti2c010_set_bus_speed(struct i2c_adapter *adap,
-			unsigned int speed)
-{
-	struct fti2c010_chip *chip = chip_list + adap->hwadapnr;
-	int ret;
-
-	fti2c010_reset(chip);
-	ret = set_i2c_bus_speed(chip, speed);
-
-	return ret;
-}
-
-/*
- * Register i2c adapters
- */
-U_BOOT_I2C_ADAP_COMPLETE(i2c_0, fti2c010_init, fti2c010_probe, fti2c010_read,
-			fti2c010_write, fti2c010_set_bus_speed,
-			CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE,
-			0)
-#ifdef CONFIG_FTI2C010_BASE1
-U_BOOT_I2C_ADAP_COMPLETE(i2c_1, fti2c010_init, fti2c010_probe, fti2c010_read,
-			fti2c010_write, fti2c010_set_bus_speed,
-			CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE,
-			1)
-#endif
-#ifdef CONFIG_FTI2C010_BASE2
-U_BOOT_I2C_ADAP_COMPLETE(i2c_2, fti2c010_init, fti2c010_probe, fti2c010_read,
-			fti2c010_write, fti2c010_set_bus_speed,
-			CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE,
-			2)
-#endif
-#ifdef CONFIG_FTI2C010_BASE3
-U_BOOT_I2C_ADAP_COMPLETE(i2c_3, fti2c010_init, fti2c010_probe, fti2c010_read,
-			fti2c010_write, fti2c010_set_bus_speed,
-			CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE,
-			3)
-#endif
diff --git a/drivers/i2c/fti2c010.h b/drivers/i2c/fti2c010.h
deleted file mode 100644
index b9d0eb74a6..0000000000
--- a/drivers/i2c/fti2c010.h
+++ /dev/null
@@ -1,80 +0,0 @@
-/*
- * Faraday I2C Controller
- *
- * (C) Copyright 2010 Faraday Technology
- * Dante Su <dantesu@faraday-tech.com>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#ifndef __FTI2C010_H
-#define __FTI2C010_H
-
-/*
- * FTI2C010 registers
- */
-struct fti2c010_regs {
-	uint32_t cr;  /* 0x00: control register */
-	uint32_t sr;  /* 0x04: status register */
-	uint32_t cdr; /* 0x08: clock division register */
-	uint32_t dr;  /* 0x0c: data register */
-	uint32_t sar; /* 0x10: slave address register */
-	uint32_t tgsr;/* 0x14: time & glitch suppression register */
-	uint32_t bmr; /* 0x18: bus monitor register */
-	uint32_t rsvd[5];
-	uint32_t revr;/* 0x30: revision register */
-};
-
-/*
- * control register
- */
-#define CR_ALIRQ      0x2000  /* arbitration lost interrupt (master) */
-#define CR_SAMIRQ     0x1000  /* slave address match interrupt (slave) */
-#define CR_STOPIRQ    0x800   /* stop condition interrupt (slave) */
-#define CR_NAKRIRQ    0x400   /* NACK response interrupt (master) */
-#define CR_DRIRQ      0x200   /* rx interrupt (both) */
-#define CR_DTIRQ      0x100   /* tx interrupt (both) */
-#define CR_TBEN       0x80    /* tx enable (both) */
-#define CR_NAK        0x40    /* NACK (both) */
-#define CR_STOP       0x20    /* stop (master) */
-#define CR_START      0x10    /* start (master) */
-#define CR_GCEN       0x8     /* general call support (slave) */
-#define CR_SCLEN      0x4     /* enable clock out (master) */
-#define CR_I2CEN      0x2     /* enable I2C (both) */
-#define CR_I2CRST     0x1     /* reset I2C (both) */
-#define CR_ENABLE     \
-	(CR_ALIRQ | CR_NAKRIRQ | CR_DRIRQ | CR_DTIRQ | CR_SCLEN | CR_I2CEN)
-
-/*
- * status register
- */
-#define SR_CLRAL      0x400    /* clear arbitration lost */
-#define SR_CLRGC      0x200    /* clear general call */
-#define SR_CLRSAM     0x100    /* clear slave address match */
-#define SR_CLRSTOP    0x80     /* clear stop */
-#define SR_CLRNAKR    0x40     /* clear NACK respond */
-#define SR_DR         0x20     /* rx ready */
-#define SR_DT         0x10     /* tx done */
-#define SR_BB         0x8      /* bus busy */
-#define SR_BUSY       0x4      /* chip busy */
-#define SR_ACK        0x2      /* ACK/NACK received */
-#define SR_RW         0x1      /* set when master-rx or slave-tx mode */
-
-/*
- * clock division register
- */
-#define CDR_DIV(n)    ((n) & 0x3ffff)
-
-/*
- * time & glitch suppression register
- */
-#define TGSR_GSR(n)   (((n) & 0x7) << 10)
-#define TGSR_TSR(n)   ((n) & 0x3ff)
-
-/*
- * bus monitor register
- */
-#define BMR_SCL       0x2      /* SCL is pull-up */
-#define BMR_SDA       0x1      /* SDA is pull-up */
-
-#endif /* __FTI2C010_H */