board/BuR/kwb: switch to board HW-Rev3

The board has been redesigned, therefore we need from now other I/O Pins to
mux and handle.

Older boards aren't supported from now anymore.

Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>

3 files changed, 89 insertions, 63 deletions

diff --git a/board/BuR/kwb/board.c b/board/BuR/kwb/board.c
index 804765a8de..30900bc4b2 100644
--- a/board/BuR/kwb/board.c
+++ b/board/BuR/kwb/board.c
@@ -26,14 +26,13 @@
 #include <i2c.h>
 #include <power/tps65217.h>
 #include "../common/bur_common.h"
+#include <lcd.h>
 
 /* -------------------------------------------------------------------------*/
 /* -- defines for used GPIO Hardware -- */
-#define KEY						(0+4)
-#define LCD_PWR						(0+5)
-#define PUSH_KEY					(0+31)
-#define USB2SD_NRST					(32+29)
-#define USB2SD_PWR					(96+13)
+#define ESC_KEY					(0+19)
+#define LCD_PWR					(0+5)
+#define PUSH_KEY				(0+31)
 /* -------------------------------------------------------------------------*/
 /* -- PSOC Resetcontroller Register defines -- */
 
@@ -46,6 +45,7 @@
 
 /* -- defines for RSTCTRL_CTRLREG  -- */
 #define	RSTCTRL_FORCE_PWR_NEN			0x0404
+#define	RSTCTRL_CAN_STB				0x4040
 
 #if defined(CONFIG_SPL_BUILD)
 /* TODO: check ram-timing ! */
@@ -107,10 +107,13 @@ void am33xx_spl_board_init(void)
 		&cmper->epwmss0clkctrl,
 		&cmper->epwmss1clkctrl,
 		&cmper->epwmss2clkctrl,
+		&cmper->lcdclkctrl,
+		&cmper->lcdcclkstctrl,
 		0
 	};
 	do_enable_clocks(clk_domains, clk_modules_kwbspecific, 1);
-
+	/* setup LCD-Pixel Clock */
+	writel(0x2, CM_DPLL + 0x34);
 	/* power-OFF LCD-Display */
 	gpio_direction_output(LCD_PWR, 0);
 
@@ -121,7 +124,7 @@ void am33xx_spl_board_init(void)
 	/* power-ON  3V3 via Resetcontroller */
 	oldspeed = i2c_get_bus_speed();
 	if (i2c_set_bus_speed(CONFIG_SYS_OMAP24_I2C_SPEED_PSOC) >= 0) {
-		buf = RSTCTRL_FORCE_PWR_NEN;
+		buf = RSTCTRL_FORCE_PWR_NEN | RSTCTRL_CAN_STB;
 		i2c_write(RSTCTRL_ADDR, RSTCTRL_CTRLREG, 1,
 			  (uint8_t *)&buf, sizeof(buf));
 		i2c_set_bus_speed(oldspeed);
@@ -129,15 +132,6 @@ void am33xx_spl_board_init(void)
 		puts("ERROR: i2c_set_bus_speed failed! (turn on PWR_nEN)\n");
 	}
 
-#if defined(CONFIG_AM335X_USB0)
-	/* power on USB2SD Controller */
-	gpio_direction_output(USB2SD_PWR, 1);
-	mdelay(1);
-	/* give a reset Pulse to USB2SD Controller */
-	gpio_direction_output(USB2SD_NRST, 0);
-	mdelay(1);
-	gpio_set_value(USB2SD_NRST, 1);
-#endif
 	pmicsetup(0);
 }
 
@@ -166,7 +160,6 @@ int board_init(void)
 #ifdef CONFIG_BOARD_LATE_INIT
 int board_late_init(void)
 {
-	const unsigned int ton  = 250;
 	const unsigned int toff = 1000;
 	unsigned int cnt  = 3;
 	unsigned short buf = 0xAAAA;
@@ -175,50 +168,77 @@ int board_late_init(void)
 	tps65217_reg_write(TPS65217_PROT_LEVEL_NONE,
 			   TPS65217_WLEDCTRL2, 0x32, 0xFF); /* 50% dimlevel */
 
-	if (gpio_get_value(KEY)) {
+	if (gpio_get_value(ESC_KEY)) {
 		do {
-			/* turn on light */
-			tps65217_reg_write(TPS65217_PROT_LEVEL_NONE,
-					   TPS65217_WLEDCTRL1, 0x09, 0xFF);
-			mdelay(ton);
-			/* turn off light */
-			tps65217_reg_write(TPS65217_PROT_LEVEL_NONE,
-					   TPS65217_WLEDCTRL1, 0x01, 0xFF);
+			lcd_position_cursor(1, 8);
+			switch (cnt) {
+			case 3:
+				lcd_puts(
+				"release ESC-KEY to enter SERVICE-mode.");
+				break;
+			case 2:
+				lcd_puts(
+				"release ESC-KEY to enter DIAGNOSE-mode.");
+				break;
+			case 1:
+				lcd_puts(
+				"release ESC-KEY to enter BOOT-mode.    ");
+				break;
+			}
 			mdelay(toff);
 			cnt--;
-			if (!gpio_get_value(KEY) &&
+			if (!gpio_get_value(ESC_KEY) &&
+			    gpio_get_value(PUSH_KEY) && 2 == cnt) {
+				lcd_position_cursor(1, 8);
+				lcd_puts(
+				"switching to network-console ...       ");
+				setenv("bootcmd", "run netconsole");
+				cnt = 4;
+				break;
+			} else if (!gpio_get_value(ESC_KEY) &&
 			    gpio_get_value(PUSH_KEY) && 1 == cnt) {
-				puts("updating from USB ...\n");
+				lcd_position_cursor(1, 8);
+				lcd_puts(
+				"updating U-BOOT from USB ...           ");
 				setenv("bootcmd", "run usbupdate");
+				cnt = 4;
 				break;
-			} else if (!gpio_get_value(KEY)) {
+			} else if ((!gpio_get_value(ESC_KEY) &&
+				    gpio_get_value(PUSH_KEY) && cnt == 0) ||
+				    (gpio_get_value(ESC_KEY) &&
+				    gpio_get_value(PUSH_KEY) && cnt == 0)) {
+				lcd_position_cursor(1, 8);
+				lcd_puts(
+				"starting script from network ...      ");
+				setenv("bootcmd", "run netscript");
+				cnt = 4;
+				break;
+			} else if (!gpio_get_value(ESC_KEY)) {
 				break;
 			}
 		} while (cnt);
 	}
 
+	lcd_position_cursor(1, 8);
 	switch (cnt) {
 	case 0:
-		puts("3 blinks ... entering BOOT mode.\n");
+		lcd_puts("entering BOOT-mode.                    ");
+		setenv("bootcmd", "run defaultAR");
 		buf = 0x0000;
 		break;
 	case 1:
-		puts("2 blinks ... entering DIAGNOSE mode.\n");
+		lcd_puts("entering DIAGNOSE-mode.                ");
 		buf = 0x0F0F;
 		break;
 	case 2:
-		puts("1 blinks ... entering SERVICE mode.\n");
+		lcd_puts("entering SERVICE mode.                 ");
 		buf = 0xB4B4;
 		break;
 	case 3:
-		puts("0 blinks ... entering RUN mode.\n");
+		lcd_puts("loading OS...                          ");
 		buf = 0x0404;
 		break;
 	}
-	mdelay(ton);
-	/* turn on light */
-	tps65217_reg_write(TPS65217_PROT_LEVEL_NONE,
-			   TPS65217_WLEDCTRL1, 0x09, 0xFF);
 	/* write bootinfo into scratchregister of resetcontroller */
 	oldspeed = i2c_get_bus_speed();
 	if (i2c_set_bus_speed(CONFIG_SYS_OMAP24_I2C_SPEED_PSOC) >= 0) {
diff --git a/board/BuR/kwb/mux.c b/board/BuR/kwb/mux.c
index ecb2e7a427..9f89b5e53d 100644
--- a/board/BuR/kwb/mux.c
+++ b/board/BuR/kwb/mux.c
@@ -16,23 +16,17 @@
 #include <asm/io.h>
 #include <i2c.h>
 
-static struct module_pin_mux usb0_pin_mux[] = {
-	{OFFSET(usb0_id), (MODE(0) | RXACTIVE)},
-	/* USB0 DrvBus Receiver disable (from romcode 0x20) */
-	{OFFSET(usb0_drvvbus), (MODE(0))},
-	/* USB1 DrvBus as GPIO due to HW-Workaround */
-	{OFFSET(usb1_drvvbus), (MODE(7))},
-	{-1},
-};
-static struct module_pin_mux spi1_pin_mux[] = {
+static struct module_pin_mux spi0_pin_mux[] = {
 	/* SPI1_SCLK */
-	{OFFSET(mcasp0_aclkx), MODE(3) | PULLUDEN |             RXACTIVE},
+	{OFFSET(spi0_sclk),	MODE(0) | PULLUDEN | RXACTIVE},
 	/* SPI1_D0 */
-	{OFFSET(mcasp0_fsx),   MODE(3) | PULLUDEN |		RXACTIVE},
+	{OFFSET(spi0_d0),	MODE(0) | PULLUDEN | RXACTIVE},
 	/* SPI1_D1 */
-	{OFFSET(mcasp0_axr0),  MODE(3) | PULLUDEN |             RXACTIVE},
+	{OFFSET(spi0_d1),	MODE(0) | PULLUDEN | RXACTIVE},
 	/* SPI1_CS0 */
-	{OFFSET(mcasp0_ahclkr), MODE(3) | PULLUDEN | PULLUP_EN | RXACTIVE},
+	{OFFSET(spi0_cs0),	MODE(0) | PULLUDEN | PULLUP_EN | RXACTIVE},
+	/* SPI1_CS1 */
+	{OFFSET(spi0_cs1),	MODE(0) | PULLUDEN | PULLUP_EN | RXACTIVE},
 	{-1},
 };
 
@@ -53,30 +47,34 @@ static struct module_pin_mux dcan1_pin_mux[] = {
 };
 
 static struct module_pin_mux gpios[] = {
-	/* GPIO0_29 (RMII1_REFCLK) - eMMC nRST */
-	{OFFSET(rmii1_refclk), (MODE(7) | PULLUDDIS)},
-	/* GPIO0_4  (SPI D1) - TA602 */
-	{OFFSET(spi0_d1), (MODE(7) | PULLUDDIS | RXACTIVE)},
-	/* GPIO0_5  (SPI CS0) - DISPLAY_ON_OFF */
-	{OFFSET(spi0_cs0), (MODE(7) | PULLUDDIS)},
 	/* GPIO0_7  (PWW0 OUT) - CAN TERM */
 	{OFFSET(ecap0_in_pwm0_out), (MODE(7) | PULLUDDIS | RXACTIVE)},
-	/* GPIO0_19 (DMA_INTR0) - CLKOUT SYS */
-	{OFFSET(xdma_event_intr0), (MODE(7) | RXACTIVE)},
-	/* GPIO0_20 (DMA_INTR1) - SPI1 nCS1 */
-	{OFFSET(xdma_event_intr1), (MODE(7) | PULLUDEN | PULLUP_EN)},
+	/* GPIO0_19 (DMA_INTR0) - TA602 */
+	{OFFSET(xdma_event_intr0), (MODE(7) | PULLUDDIS | RXACTIVE)},
+	/* GPIO0_20 (DMA_INTR1) - SPI0 nCS1 */
+	{OFFSET(xdma_event_intr1), (MODE(7) | PULLUDDIS | RXACTIVE)},
+	/* GPIO0_29 (RMII1_REFCLK) - eMMC nRST */
+	{OFFSET(rmii1_refclk), (MODE(7) | PULLUDDIS)},
 	/* GPIO0_30 (GPMC_WAIT0) - TA601 */
 	{OFFSET(gpmc_wait0), (MODE(7) | PULLUDDIS | RXACTIVE)},
 	/* GPIO0_31 (GPMC_nWP) - SW601 PushButton */
 	{OFFSET(gpmc_wpn), (MODE(7) | PULLUDDIS | RXACTIVE)},
 	/* GPIO1_28 (GPMC_nWE) - FRAM_nWP */
 	{OFFSET(gpmc_be1n), (MODE(7) | PULLUDDIS)},
+	/* GPIO1_29 (gpmc_csn0) - MMC nRST */
+	{OFFSET(gpmc_csn0), (MODE(7) | PULLUDDIS)},
 	/* GPIO2_0  (GPMC_nCS3)	- VBAT_OK */
 	{OFFSET(gpmc_csn3), (MODE(7) | PULLUDDIS | RXACTIVE) },
 	/* GPIO2_2  (GPMC_nADV_ALE) - DCOK */
 	{OFFSET(gpmc_advn_ale), (MODE(7) | PULLUDDIS | RXACTIVE)},
 	/* GPIO2_4  (GPMC_nWE) - TST_BAST */
 	{OFFSET(gpmc_wen), (MODE(7) | PULLUDDIS)},
+	/* GPIO2_5  (gpmc_be0n_cle) - DISPLAY_ON_OFF */
+	{OFFSET(gpmc_be0n_cle), (MODE(7) | PULLUDDIS)},
+	/* GPIO3_16 (mcasp0_axr0) - ETH-LED green */
+	{OFFSET(mcasp0_axr0), (MODE(7) | PULLUDDIS | RXACTIVE)},
+	/* GPIO3_17 (mcasp0_ahclkr) - CAN_STB */
+	{OFFSET(mcasp0_ahclkr), (MODE(7) | PULLUDDIS | RXACTIVE)},
 	/* GPIO3_18 (MCASP0_ACLKR) - SW601 CNTup, mapped to Counter eQEB0A_in */
 	{OFFSET(mcasp0_aclkr), (MODE(1) | PULLUDDIS | RXACTIVE)},
 	/* GPIO3_19 (MCASP0_FSR) - SW601 CNTdown, mapped to Counter eQEB0B_in */
@@ -126,6 +124,10 @@ static struct module_pin_mux mii1_pin_mux[] = {
 };
 
 static struct module_pin_mux mmc1_pin_mux[] = {
+	{OFFSET(gpmc_ad7), (MODE(1) | RXACTIVE | PULLUP_EN)},	/* MMC1_DAT7 */
+	{OFFSET(gpmc_ad6), (MODE(1) | RXACTIVE | PULLUP_EN)},	/* MMC1_DAT6 */
+	{OFFSET(gpmc_ad5), (MODE(1) | RXACTIVE | PULLUP_EN)},	/* MMC1_DAT5 */
+	{OFFSET(gpmc_ad4), (MODE(1) | RXACTIVE | PULLUP_EN)},	/* MMC1_DAT4 */
 	{OFFSET(gpmc_ad3), (MODE(1) | RXACTIVE | PULLUP_EN)},	/* MMC1_DAT3 */
 	{OFFSET(gpmc_ad2), (MODE(1) | RXACTIVE | PULLUP_EN)},	/* MMC1_DAT2 */
 	{OFFSET(gpmc_ad1), (MODE(1) | RXACTIVE | PULLUP_EN)},	/* MMC1_DAT1 */
@@ -187,8 +189,7 @@ void enable_board_pin_mux(void)
 {
 	configure_module_pin_mux(i2c0_pin_mux);
 	configure_module_pin_mux(mii1_pin_mux);
-	configure_module_pin_mux(usb0_pin_mux);
-	configure_module_pin_mux(spi1_pin_mux);
+	configure_module_pin_mux(spi0_pin_mux);
 	configure_module_pin_mux(dcan0_pin_mux);
 	configure_module_pin_mux(dcan1_pin_mux);
 	configure_module_pin_mux(mmc1_pin_mux);
diff --git a/include/configs/kwb.h b/include/configs/kwb.h
index 29b263f301..2c59fbdd27 100644
--- a/include/configs/kwb.h
+++ b/include/configs/kwb.h
@@ -14,6 +14,11 @@
 
 #include <configs/bur_am335x_common.h>
 /* ------------------------------------------------------------------------- */
+#define CONFIG_AM335X_LCD
+#define CONFIG_LCD
+#define CONFIG_LCD_NOSTDOUT
+#define CONFIG_SYS_WHITE_ON_BLACK
+#define LCD_BPP				LCD_COLOR32
 /* Clock Defines */
 #define V_OSCK				26000000  /* Clock output from T2 */
 #define V_SCLK				(V_OSCK)
@@ -87,8 +92,6 @@
 #undef	CONFIG_BOOTM_NETBSD
 #undef	CONFIG_BOOTM_PLAN9
 #undef	CONFIG_BOOTM_RTEMS
-#undef	CONFIG_GZIP
-#undef	CONFIG_ZLIB
 
 /* USB configuration */
 #define CONFIG_USB_MUSB_DSPS
@@ -100,6 +103,8 @@
 #define CONFIG_MUSB_HOST
 #define CONFIG_AM335X_USB0
 #define CONFIG_AM335X_USB0_MODE	MUSB_HOST
+#define CONFIG_AM335X_USB1
+#define CONFIG_AM335X_USB1_MODE	MUSB_HOST
 
 #ifdef CONFIG_MUSB_HOST
 #define CONFIG_CMD_USB