Merge branch 'master' of git://git.denx.de/u-boot-sh

4 files changed, 331 insertions, 6 deletions

diff --git a/Makefile b/Makefile
index 57cb4b87d9..50abc979ad 100644
--- a/Makefile
+++ b/Makefile
@@ -926,6 +926,16 @@ OBJCOPYFLAGS_u-boot.srec := -O srec
 u-boot.hex u-boot.srec: u-boot FORCE
 	$(call if_changed,objcopy)
 
+OBJCOPYFLAGS_u-boot-elf.srec := $(OBJCOPYFLAGS_u-boot.srec)
+
+u-boot-elf.srec: u-boot.elf FORCE
+	$(call if_changed,objcopy)
+
+OBJCOPYFLAGS_u-boot-spl.srec = $(OBJCOPYFLAGS_u-boot.srec)
+
+spl/u-boot-spl.srec: spl/u-boot-spl FORCE
+	$(call if_changed,objcopy)
+
 OBJCOPYFLAGS_u-boot-nodtb.bin := -O binary \
 		$(if $(CONFIG_X86_16BIT_INIT),-R .start16 -R .resetvec)
 
diff --git a/arch/arm/dts/r8a7790-stout.dts b/arch/arm/dts/r8a7790-stout.dts
index eb82934c59..301cb728fe 100644
--- a/arch/arm/dts/r8a7790-stout.dts
+++ b/arch/arm/dts/r8a7790-stout.dts
@@ -8,19 +8,112 @@
 
 /dts-v1/;
 #include "r8a7790.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
 
 / {
 	model = "Stout";
 	compatible = "renesas,stout", "renesas,r8a7790";
 
 	aliases {
-		serial0 = &scif0;
+		serial0 = &scifa0;
+	};
+
+	chosen {
+		bootargs = "ignore_loglevel rw root=/dev/nfs ip=dhcp";
+		stdout-path = "serial0:115200n8";
 	};
 
 	memory@40000000 {
 		device_type = "memory";
 		reg = <0 0x40000000 0 0x40000000>;
 	};
+
+	leds {
+		compatible = "gpio-leds";
+		led1 {
+			gpios = <&gpio4 22 GPIO_ACTIVE_LOW>;
+		};
+		led2 {
+			gpios = <&gpio4 23 GPIO_ACTIVE_LOW>;
+		};
+		led3 {
+			gpios = <&gpio5 17 GPIO_ACTIVE_LOW>;
+		};
+		led5 {
+			gpios = <&gpio4 24 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	fixedregulator3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-3.3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	vcc_sdhi0: regulator-vcc-sdhi0 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "SDHI0 Vcc";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&gpio5 24 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	hdmi-out {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_out: endpoint {
+				remote-endpoint = <&adv7511_out>;
+			};
+		};
+	};
+
+	osc1_clk: osc1-clock {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <148500000>;
+	};
+
+	osc4_clk: osc4-clock {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <12000000>;
+	};
+};
+
+&du {
+	pinctrl-0 = <&du_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	clocks = <&cpg CPG_MOD 724>, <&cpg CPG_MOD 723>, <&cpg CPG_MOD 722>,
+		 <&cpg CPG_MOD 726>, <&cpg CPG_MOD 725>,
+		 <&osc1_clk>;
+	clock-names = "du.0", "du.1", "du.2", "lvds.0", "lvds.1", "dclkin.0";
+
+	ports {
+		port@0 {
+			endpoint {
+				remote-endpoint = <&adv7511_in>;
+			};
+		};
+		port@1 {
+			lvds_connector0: endpoint {
+			};
+		};
+		port@2 {
+			lvds_connector1: endpoint {
+			};
+		};
+	};
 };
 
 &extal_clk {
@@ -28,22 +121,128 @@
 };
 
 &pfc {
+
 	pinctrl-0 = <&scif_clk_pins>;
 	pinctrl-names = "default";
 
-	scif0_pins: scif0 {
-		groups = "scif0_data";
-		function = "scif0";
+	du_pins: du {
+		groups = "du_rgb888", "du_sync_1", "du_clk_out_0";
+		function = "du";
+	};
+
+	scifa0_pins: scifa0 {
+		groups = "scifa0_data_b";
+		function = "scifa0";
 	};
 
 	scif_clk_pins: scif_clk {
 		groups = "scif_clk";
 		function = "scif_clk";
 	};
+
+	ether_pins: ether {
+		groups = "eth_link", "eth_mdio", "eth_rmii";
+		function = "eth";
+	};
+
+	phy1_pins: phy1 {
+		groups = "intc_irq1";
+		function = "intc";
+	};
+
+	sdhi0_pins: sd0 {
+		groups = "sdhi0_data4", "sdhi0_ctrl";
+		function = "sdhi0";
+		power-source = <3300>;
+	};
+
+	qspi_pins: qspi {
+		groups = "qspi_ctrl", "qspi_data4";
+		function = "qspi";
+	};
+
+	iic2_pins: iic2 {
+		groups = "iic2_b";
+		function = "iic2";
+	};
+
+	iic3_pins: iic3 {
+		groups = "iic3";
+		function = "iic3";
+	};
+
+	usb0_pins: usb0 {
+		groups = "usb0";
+		function = "usb0";
+	};
 };
 
-&scif0 {
-	pinctrl-0 = <&scif0_pins>;
+&ether {
+	pinctrl-0 = <&ether_pins &phy1_pins>;
+	pinctrl-names = "default";
+
+	phy-handle = <&phy1>;
+	renesas,ether-link-active-low;
+	status = "okay";
+
+	phy1: ethernet-phy@1 {
+		reg = <1>;
+		interrupt-parent = <&irqc0>;
+		interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
+		micrel,led-mode = <1>;
+	};
+};
+
+&cmt0 {
+	status = "okay";
+};
+
+&qspi {
+	pinctrl-0 = <&qspi_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+
+	flash: flash@0 {
+		compatible = "spansion,s25fl512s", "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <30000000>;
+		spi-tx-bus-width = <4>;
+		spi-rx-bus-width = <4>;
+		spi-cpha;
+		spi-cpol;
+		m25p,fast-read;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "loader";
+				reg = <0x00000000 0x00080000>;
+				read-only;
+			};
+			partition@80000 {
+				label = "uboot";
+				reg = <0x00080000 0x00040000>;
+				read-only;
+			};
+			partition@c0000 {
+				label = "uboot-env";
+				reg = <0x000c0000 0x00040000>;
+				read-only;
+			};
+			partition@100000 {
+				label = "flash";
+				reg = <0x00100000 0x03f00000>;
+			};
+		};
+	};
+};
+
+&scifa0 {
+	pinctrl-0 = <&scifa0_pins>;
 	pinctrl-names = "default";
 
 	status = "okay";
@@ -52,3 +251,114 @@
 &scif_clk {
 	clock-frequency = <14745600>;
 };
+
+&sdhi0 {
+	pinctrl-0 = <&sdhi0_pins>;
+	pinctrl-names = "default";
+
+	vmmc-supply = <&vcc_sdhi0>;
+	cd-gpios = <&gpio3 6 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&cpu0 {
+	cpu0-supply = <&vdd_dvfs>;
+};
+
+&iic2	{
+	status = "okay";
+	pinctrl-0 = <&iic2_pins>;
+	pinctrl-names = "default";
+
+	clock-frequency = <100000>;
+
+	hdmi@39 {
+		compatible = "adi,adv7511w";
+		reg = <0x39>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
+		clocks = <&osc4_clk>;
+		clock-names = "cec";
+
+		adi,input-depth = <8>;
+		adi,input-colorspace = "rgb";
+		adi,input-clock = "1x";
+		adi,input-style = <1>;
+		adi,input-justification = "evenly";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				adv7511_in: endpoint {
+					remote-endpoint = <&du_out_rgb>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+				adv7511_out: endpoint {
+					remote-endpoint = <&hdmi_con_out>;
+				};
+			};
+		};
+	};
+};
+
+&iic3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&iic3_pins>;
+	status = "okay";
+
+	pmic@58 {
+		compatible = "dlg,da9063";
+		reg = <0x58>;
+		interrupt-parent = <&irqc0>;
+		interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-controller;
+
+		rtc {
+			compatible = "dlg,da9063-rtc";
+		};
+
+		wdt {
+			compatible = "dlg,da9063-watchdog";
+		};
+	};
+
+	vdd_dvfs: regulator@68 {
+		compatible = "dlg,da9210";
+		reg = <0x68>;
+		interrupt-parent = <&irqc0>;
+		interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
+
+		regulator-min-microvolt = <1000000>;
+		regulator-max-microvolt = <1000000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	vdd: regulator@70 {
+		compatible = "dlg,da9210";
+		reg = <0x70>;
+		interrupt-parent = <&irqc0>;
+		interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
+
+		regulator-min-microvolt = <1000000>;
+		regulator-max-microvolt = <1000000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+};
+
+&pci0 {
+	status = "okay";
+	pinctrl-0 = <&usb0_pins>;
+	pinctrl-names = "default";
+};
+
+&usbphy {
+	status = "okay";
+};
diff --git a/include/configs/rcar-gen2-common.h b/include/configs/rcar-gen2-common.h
index 1ceee9a429..6069220406 100644
--- a/include/configs/rcar-gen2-common.h
+++ b/include/configs/rcar-gen2-common.h
@@ -15,6 +15,10 @@
 #define CONFIG_SETUP_MEMORY_TAGS
 #define CONFIG_INITRD_TAG
 
+#ifdef CONFIG_SPL
+#define CONFIG_SPL_TARGET	"spl/u-boot-spl.srec"
+#endif
+
 #undef	CONFIG_SHOW_BOOT_PROGRESS
 
 #define CONFIG_ARCH_CPU_INIT
diff --git a/include/configs/rcar-gen3-common.h b/include/configs/rcar-gen3-common.h
index 1ae6323369..bbaab80e23 100644
--- a/include/configs/rcar-gen3-common.h
+++ b/include/configs/rcar-gen3-common.h
@@ -13,6 +13,7 @@
 #include <asm/arch/rmobile.h>
 
 #define CONFIG_REMAKE_ELF
+#define CONFIG_BUILD_TARGET	"u-boot-elf.srec"
 
 /* boot option */