Merge tag 'u-boot-stm32-20200214' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm

- add DH Electronics DHCOM SoM and PDK2 board
- DT alignment with kernel v5.5-rc7 for stm32mp1 boards
- fix STM32 image format for big endian hosts in mkimage
- solve warnings in device tree and code for stm32mp1 boards
- remove fdt_high and initrd_high for stm32 and stih boards
- add support of STM32MP15x Rev.Z
- update stm32mp1 readme

42 files changed, 1922 insertions, 173 deletions

diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 4fee5cc489..be4cf029d0 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -882,7 +882,8 @@ dtb-$(CONFIG_STM32MP15x) += \
 	stm32mp157a-avenger96.dtb \
 	stm32mp157c-dk2.dtb \
 	stm32mp157c-ed1.dtb \
-	stm32mp157c-ev1.dtb
+	stm32mp157c-ev1.dtb \
+	stm32mp15xx-dhcom-pdk2.dtb
 
 dtb-$(CONFIG_SOC_K3_AM6) += k3-am654-base-board.dtb k3-am654-r5-base-board.dtb
 dtb-$(CONFIG_SOC_K3_J721E) += k3-j721e-common-proc-board.dtb \
diff --git a/arch/arm/dts/stm32mp15-ddr.dtsi b/arch/arm/dts/stm32mp15-ddr.dtsi
index 479b700c86..38f29bb789 100644
--- a/arch/arm/dts/stm32mp15-ddr.dtsi
+++ b/arch/arm/dts/stm32mp15-ddr.dtsi
@@ -5,7 +5,7 @@
 
 / {
 	soc {
-		ddr: ddr@5A003000 {
+		ddr: ddr@5a003000 {
 			u-boot,dm-pre-reloc;
 
 			compatible = "st,stm32mp1-ddr";
diff --git a/arch/arm/dts/stm32mp157-pinctrl.dtsi b/arch/arm/dts/stm32mp157-pinctrl.dtsi
index 0d53396119..81a363d93d 100644
--- a/arch/arm/dts/stm32mp157-pinctrl.dtsi
+++ b/arch/arm/dts/stm32mp157-pinctrl.dtsi
@@ -138,7 +138,16 @@
 				status = "disabled";
 			};
 
-			adc12_usb_pwr_pins_a: adc12-usb-pwr-pins-0 {
+			adc12_ain_pins_a: adc12-ain-0 {
+				pins {
+					pinmux = <STM32_PINMUX('C', 3, ANALOG)>, /* ADC1 in13 */
+						 <STM32_PINMUX('F', 12, ANALOG)>, /* ADC1 in6 */
+						 <STM32_PINMUX('F', 13, ANALOG)>, /* ADC2 in2 */
+						 <STM32_PINMUX('F', 14, ANALOG)>; /* ADC2 in6 */
+				};
+			};
+
+			adc12_usb_cc_pins_a: adc12-usb-cc-pins-0 {
 				pins {
 					pinmux = <STM32_PINMUX('A', 4, ANALOG)>, /* ADC12 in18 */
 						 <STM32_PINMUX('A', 5, ANALOG)>; /* ADC12 in19 */
@@ -175,6 +184,18 @@
 				};
 			};
 
+			dac_ch1_pins_a: dac-ch1 {
+				pins {
+					pinmux = <STM32_PINMUX('A', 4, ANALOG)>;
+				};
+			};
+
+			dac_ch2_pins_a: dac-ch2 {
+				pins {
+					pinmux = <STM32_PINMUX('A', 5, ANALOG)>;
+				};
+			};
+
 			dcmi_pins_a: dcmi-0 {
 				pins {
 					pinmux = <STM32_PINMUX('H', 8,  AF13)>,/* DCMI_HSYNC */
@@ -622,13 +643,13 @@
 						 <STM32_PINMUX('F', 6, AF9)>; /* QSPI_BK1_IO3 */
 					bias-disable;
 					drive-push-pull;
-					slew-rate = <3>;
+					slew-rate = <1>;
 				};
 				pins2 {
 					pinmux = <STM32_PINMUX('B', 6, AF10)>; /* QSPI_BK1_NCS */
 					bias-pull-up;
 					drive-push-pull;
-					slew-rate = <3>;
+					slew-rate = <1>;
 				};
 			};
 
@@ -650,13 +671,13 @@
 						 <STM32_PINMUX('G', 7, AF11)>; /* QSPI_BK2_IO3 */
 					bias-disable;
 					drive-push-pull;
-					slew-rate = <3>;
+					slew-rate = <1>;
 				};
 				pins2 {
 					pinmux = <STM32_PINMUX('C', 0, AF10)>; /* QSPI_BK2_NCS */
 					bias-pull-up;
 					drive-push-pull;
-					slew-rate = <3>;
+					slew-rate = <1>;
 				};
 			};
 
diff --git a/arch/arm/dts/stm32mp157-u-boot.dtsi b/arch/arm/dts/stm32mp157-u-boot.dtsi
index 0d1d387e54..8f9535a4db 100644
--- a/arch/arm/dts/stm32mp157-u-boot.dtsi
+++ b/arch/arm/dts/stm32mp157-u-boot.dtsi
@@ -128,12 +128,14 @@
 	u-boot,dm-pre-reloc;
 };
 
-&pwr {
+&pwr_regulators {
 	u-boot,dm-pre-reloc;
 };
 
 &rcc {
 	u-boot,dm-pre-reloc;
+	#address-cells = <1>;
+	#size-cells = <0>;
 };
 
 &sdmmc1 {
diff --git a/arch/arm/dts/stm32mp157a-avenger96-u-boot.dtsi b/arch/arm/dts/stm32mp157a-avenger96-u-boot.dtsi
index 1104a70a65..d6dc746365 100644
--- a/arch/arm/dts/stm32mp157a-avenger96-u-boot.dtsi
+++ b/arch/arm/dts/stm32mp157a-avenger96-u-boot.dtsi
@@ -91,7 +91,7 @@
 		CLK_UART6_HSI
 		CLK_UART78_HSI
 		CLK_SPDIF_PLL4P
-		CLK_FDCAN_PLL4Q
+		CLK_FDCAN_PLL4R
 		CLK_SAI1_PLL3Q
 		CLK_SAI2_PLL3Q
 		CLK_SAI3_PLL3Q
@@ -105,6 +105,8 @@
 
 	/* VCO = 1300.0 MHz => P = 650 (CPU) */
 	pll1: st,pll@0 {
+		compatible = "st,stm32mp1-pll";
+		reg = <0>;
 		cfg = < 2 80 0 0 0 PQR(1,0,0) >;
 		frac = < 0x800 >;
 		u-boot,dm-pre-reloc;
@@ -112,6 +114,8 @@
 
 	/* VCO = 1066.0 MHz => P = 266 (AXI), Q = 533 (GPU), R = 533 (DDR) */
 	pll2: st,pll@1 {
+		compatible = "st,stm32mp1-pll";
+		reg = <1>;
 		cfg = < 2 65 1 0 0 PQR(1,1,1) >;
 		frac = < 0x1400 >;
 		u-boot,dm-pre-reloc;
@@ -119,6 +123,8 @@
 
 	/* VCO = 417.8 MHz => P = 209, Q = 24, R = 11 */
 	pll3: st,pll@2 {
+		compatible = "st,stm32mp1-pll";
+		reg = <2>;
 		cfg = < 1 33 1 16 36 PQR(1,1,1) >;
 		frac = < 0x1a04 >;
 		u-boot,dm-pre-reloc;
@@ -126,6 +132,8 @@
 
 	/* VCO = 480.0 MHz => P = 120, Q = 40, R = 96 */
 	pll4: st,pll@3 {
+		compatible = "st,stm32mp1-pll";
+		reg = <3>;
 		cfg = < 1 39 3 11 4 PQR(1,1,1) >;
 		u-boot,dm-pre-reloc;
 	};
diff --git a/arch/arm/dts/stm32mp157a-avenger96.dts b/arch/arm/dts/stm32mp157a-avenger96.dts
index 5b15a4a915..3065593bf2 100644
--- a/arch/arm/dts/stm32mp157a-avenger96.dts
+++ b/arch/arm/dts/stm32mp157a-avenger96.dts
@@ -252,14 +252,13 @@
 				regulator-name = "vbus_otg";
 				interrupts = <IT_OCP_OTG 0>;
 				interrupt-parent = <&pmic>;
-				regulator-active-discharge;
 			};
 
 			vbus_sw: pwr_sw2 {
 				regulator-name = "vbus_sw";
 				interrupts = <IT_OCP_SWOUT 0>;
 				interrupt-parent = <&pmic>;
-				regulator-active-discharge;
+				regulator-active-discharge = <1>;
 			};
 		};
 
@@ -282,11 +281,9 @@
 	status = "okay";
 };
 
-&pwr {
-	pwr-regulators {
-		vdd-supply = <&vdd>;
-		vdd_3v3_usbfs-supply = <&vdd_usb>;
-	};
+&pwr_regulators {
+	vdd-supply = <&vdd>;
+	vdd_3v3_usbfs-supply = <&vdd_usb>;
 };
 
 &rng1 {
diff --git a/arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi b/arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi
index dcaab3eef2..a5cc01dd19 100644
--- a/arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi
+++ b/arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi
@@ -35,24 +35,7 @@
 };
 
 &adc {
-	pinctrl-names = "default";
-	pinctrl-0 = <&adc12_usb_pwr_pins_a>;
-	vdd-supply = <&vdd>;
-	vdda-supply = <&vdd>;
-	vref-supply = <&vrefbuf>;
 	status = "okay";
-	adc1: adc@0 {
-		/*
-		 * Type-C USB_PWR_CC1 & USB_PWR_CC2 on in18 & in19.
-		 * Use at least 5 * RC time, e.g. 5 * (Rp + Rd) * C:
-		 * 5 * (56 + 47kOhms) * 5pF => 2.5us.
-		 * Use arbitrary margin here (e.g. 5µs).
-		 */
-		st,min-sample-time-nsecs = <5000>;
-		/* ANA0, ANA1, USB Type-C CC1 & CC2 */
-		st,adc-channels = <0 1 18 19>;
-		status = "okay";
-	};
 };
 
 &clk_hse {
@@ -127,7 +110,7 @@
 		CLK_UART6_HSI
 		CLK_UART78_HSI
 		CLK_SPDIF_PLL4P
-		CLK_FDCAN_PLL4Q
+		CLK_FDCAN_PLL4R
 		CLK_SAI1_PLL3Q
 		CLK_SAI2_PLL3Q
 		CLK_SAI3_PLL3Q
@@ -141,6 +124,8 @@
 
 	/* VCO = 1300.0 MHz => P = 650 (CPU) */
 	pll1: st,pll@0 {
+		compatible = "st,stm32mp1-pll";
+		reg = <0>;
 		cfg = < 2 80 0 0 0 PQR(1,0,0) >;
 		frac = < 0x800 >;
 		u-boot,dm-pre-reloc;
@@ -148,6 +133,8 @@
 
 	/* VCO = 1066.0 MHz => P = 266 (AXI), Q = 533 (GPU), R = 533 (DDR) */
 	pll2: st,pll@1 {
+		compatible = "st,stm32mp1-pll";
+		reg = <1>;
 		cfg = < 2 65 1 0 0 PQR(1,1,1) >;
 		frac = < 0x1400 >;
 		u-boot,dm-pre-reloc;
@@ -155,6 +142,8 @@
 
 	/* VCO = 417.8 MHz => P = 209, Q = 24, R = 11 */
 	pll3: st,pll@2 {
+		compatible = "st,stm32mp1-pll";
+		reg = <2>;
 		cfg = < 1 33 1 16 36 PQR(1,1,1) >;
 		frac = < 0x1a04 >;
 		u-boot,dm-pre-reloc;
@@ -162,6 +151,8 @@
 
 	/* VCO = 594.0 MHz => P = 99, Q = 74, R = 74 */
 	pll4: st,pll@3 {
+		compatible = "st,stm32mp1-pll";
+		reg = <3>;
 		cfg = < 3 98 5 7 7 PQR(1,1,1) >;
 		u-boot,dm-pre-reloc;
 	};
diff --git a/arch/arm/dts/stm32mp157a-dk1.dts b/arch/arm/dts/stm32mp157a-dk1.dts
index 4652253012..624bf6954b 100644
--- a/arch/arm/dts/stm32mp157a-dk1.dts
+++ b/arch/arm/dts/stm32mp157a-dk1.dts
@@ -25,6 +25,7 @@
 	};
 
 	memory@c0000000 {
+		device_type = "memory";
 		reg = <0xc0000000 0x20000000>;
 	};
 
@@ -92,7 +93,34 @@
 			"Playback" , "MCLK",
 			"Capture" , "MCLK",
 			"MICL" , "Mic Bias";
-		dais = <&sai2a_port &sai2b_port>;
+		dais = <&sai2a_port &sai2b_port &i2s2_port>;
+		status = "okay";
+	};
+};
+
+&adc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&adc12_ain_pins_a>, <&adc12_usb_cc_pins_a>;
+	vdd-supply = <&vdd>;
+	vdda-supply = <&vdd>;
+	vref-supply = <&vrefbuf>;
+	status = "disabled";
+	adc1: adc@0 {
+		/*
+		 * Type-C USB_PWR_CC1 & USB_PWR_CC2 on in18 & in19.
+		 * Use at least 5 * RC time, e.g. 5 * (Rp + Rd) * C:
+		 * 5 * (56 + 47kOhms) * 5pF => 2.5us.
+		 * Use arbitrary margin here (e.g. 5us).
+		 */
+		st,min-sample-time-nsecs = <5000>;
+		/* AIN connector, USB Type-C CC1 & CC2 */
+		st,adc-channels = <0 1 6 13 18 19>;
+		status = "okay";
+	};
+	adc2: adc@100 {
+		/* AIN connector, USB Type-C CC1 & CC2 */
+		st,adc-channels = <0 1 2 6 18 19>;
+		st,min-sample-time-nsecs = <5000>;
 		status = "okay";
 	};
 };
@@ -146,9 +174,7 @@
 		reset-gpios = <&gpioa 10 GPIO_ACTIVE_LOW>;
 		interrupts = <1 IRQ_TYPE_EDGE_FALLING>;
 		interrupt-parent = <&gpiog>;
-		pinctrl-names = "default", "sleep";
-		pinctrl-0 = <&ltdc_pins_a>;
-		pinctrl-1 = <&ltdc_pins_sleep_a>;
+		#sound-dai-cells = <0>;
 		status = "okay";
 
 		ports {
@@ -161,6 +187,13 @@
 					remote-endpoint = <&ltdc_ep0_out>;
 				};
 			};
+
+			port@3 {
+				reg = <3>;
+				sii9022_tx_endpoint: endpoint {
+					remote-endpoint = <&i2s2_endpoint>;
+				};
+			};
 		};
 	};
 
@@ -244,7 +277,7 @@
 
 			vddcore: buck1 {
 				regulator-name = "vddcore";
-				regulator-min-microvolt = <800000>;
+				regulator-min-microvolt = <1200000>;
 				regulator-max-microvolt = <1350000>;
 				regulator-always-on;
 				regulator-initial-mode = <0>;
@@ -345,7 +378,7 @@
 			 vbus_sw: pwr_sw2 {
 				regulator-name = "vbus_sw";
 				interrupts = <IT_OCP_SWOUT 0>;
-				regulator-active-discharge;
+				regulator-active-discharge = <1>;
 			 };
 		};
 
@@ -364,6 +397,23 @@
 	};
 };
 
+&i2s2 {
+	clocks = <&rcc SPI2>, <&rcc SPI2_K>, <&rcc PLL3_Q>, <&rcc PLL3_R>;
+	clock-names = "pclk", "i2sclk", "x8k", "x11k";
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2s2_pins_a>;
+	pinctrl-1 = <&i2s2_pins_sleep_a>;
+	status = "okay";
+
+	i2s2_port: port {
+		i2s2_endpoint: endpoint {
+			remote-endpoint = <&sii9022_tx_endpoint>;
+			format = "i2s";
+			mclk-fs = <256>;
+		};
+	};
+};
+
 &ipcc {
 	status = "okay";
 };
@@ -374,6 +424,9 @@
 };
 
 &ltdc {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&ltdc_pins_a>;
+	pinctrl-1 = <&ltdc_pins_sleep_a>;
 	status = "okay";
 
 	port {
@@ -397,11 +450,9 @@
 	status = "okay";
 };
 
-&pwr {
-	pwr-regulators {
-		vdd-supply = <&vdd>;
-		vdd_3v3_usbfs-supply = <&vdd_usb>;
-	};
+&pwr_regulators {
+	vdd-supply = <&vdd>;
+	vdd_3v3_usbfs-supply = <&vdd_usb>;
 };
 
 &rng1 {
diff --git a/arch/arm/dts/stm32mp157c-dk2.dts b/arch/arm/dts/stm32mp157c-dk2.dts
index 020ea0f0e2..d26adcbeba 100644
--- a/arch/arm/dts/stm32mp157c-dk2.dts
+++ b/arch/arm/dts/stm32mp157c-dk2.dts
@@ -53,6 +53,19 @@
 	};
 };
 
+&i2c1 {
+	touchscreen@38 {
+		compatible = "focaltech,ft6236";
+		reg = <0x38>;
+		interrupts = <2 2>;
+		interrupt-parent = <&gpiof>;
+		interrupt-controller;
+		touchscreen-size-x = <480>;
+		touchscreen-size-y = <800>;
+		status = "okay";
+	};
+};
+
 &ltdc {
 	status = "okay";
 
diff --git a/arch/arm/dts/stm32mp157c-ed1-u-boot.dtsi b/arch/arm/dts/stm32mp157c-ed1-u-boot.dtsi
index b2ac49472a..347edf7e58 100644
--- a/arch/arm/dts/stm32mp157c-ed1-u-boot.dtsi
+++ b/arch/arm/dts/stm32mp157c-ed1-u-boot.dtsi
@@ -107,7 +107,7 @@
 		CLK_UART6_HSI
 		CLK_UART78_HSI
 		CLK_SPDIF_PLL4P
-		CLK_FDCAN_PLL4Q
+		CLK_FDCAN_PLL4R
 		CLK_SAI1_PLL3Q
 		CLK_SAI2_PLL3Q
 		CLK_SAI3_PLL3Q
@@ -121,6 +121,8 @@
 
 	/* VCO = 1300.0 MHz => P = 650 (CPU) */
 	pll1: st,pll@0 {
+		compatible = "st,stm32mp1-pll";
+		reg = <0>;
 		cfg = < 2 80 0 0 0 PQR(1,0,0) >;
 		frac = < 0x800 >;
 		u-boot,dm-pre-reloc;
@@ -128,6 +130,8 @@
 
 	/* VCO = 1066.0 MHz => P = 266 (AXI), Q = 533 (GPU), R = 533 (DDR) */
 	pll2: st,pll@1 {
+		compatible = "st,stm32mp1-pll";
+		reg = <1>;
 		cfg = < 2 65 1 0 0 PQR(1,1,1) >;
 		frac = < 0x1400 >;
 		u-boot,dm-pre-reloc;
@@ -135,6 +139,8 @@
 
 	/* VCO = 417.8 MHz => P = 209, Q = 24, R = 11 */
 	pll3: st,pll@2 {
+		compatible = "st,stm32mp1-pll";
+		reg = <2>;
 		cfg = < 1 33 1 16 36 PQR(1,1,1) >;
 		frac = < 0x1a04 >;
 		u-boot,dm-pre-reloc;
@@ -142,6 +148,8 @@
 
 	/* VCO = 594.0 MHz => P = 99, Q = 74, R = 74 */
 	pll4: st,pll@3 {
+		compatible = "st,stm32mp1-pll";
+		reg = <3>;
 		cfg = < 3 98 5 7 7 PQR(1,1,1) >;
 		u-boot,dm-pre-reloc;
 	};
diff --git a/arch/arm/dts/stm32mp157c-ed1.dts b/arch/arm/dts/stm32mp157c-ed1.dts
index bc4d7e1ab5..ae4da39ce8 100644
--- a/arch/arm/dts/stm32mp157c-ed1.dts
+++ b/arch/arm/dts/stm32mp157c-ed1.dts
@@ -84,7 +84,21 @@
 
 		gpios = <&gpiof 14 GPIO_ACTIVE_HIGH>;
 		gpios-states = <0>;
-		states = <1800000 0x1 2900000 0x0>;
+		states = <1800000 0x1>,
+			 <2900000 0x0>;
+	};
+};
+
+&dac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&dac_ch1_pins_a &dac_ch2_pins_a>;
+	vref-supply = <&vdda>;
+	status = "disabled";
+	dac1: dac@1 {
+		status = "okay";
+	};
+	dac2: dac@2 {
+		status = "okay";
 	};
 };
 
@@ -127,7 +141,7 @@
 
 			vddcore: buck1 {
 				regulator-name = "vddcore";
-				regulator-min-microvolt = <800000>;
+				regulator-min-microvolt = <1200000>;
 				regulator-max-microvolt = <1350000>;
 				regulator-always-on;
 				regulator-initial-mode = <0>;
@@ -225,7 +239,7 @@
 			 vbus_sw: pwr_sw2 {
 				regulator-name = "vbus_sw";
 				interrupts = <IT_OCP_SWOUT 0>;
-				regulator-active-discharge;
+				regulator-active-discharge = <1>;
 			 };
 		};
 
@@ -263,11 +277,9 @@
 	status = "okay";
 };
 
-&pwr {
-	pwr-regulators {
-		vdd-supply = <&vdd>;
-		vdd_3v3_usbfs-supply = <&vdd_usb>;
-	};
+&pwr_regulators {
+	vdd-supply = <&vdd>;
+	vdd_3v3_usbfs-supply = <&vdd_usb>;
 };
 
 &rng1 {
diff --git a/arch/arm/dts/stm32mp157c-ev1.dts b/arch/arm/dts/stm32mp157c-ev1.dts
index 89d29b50c3..bd8ffc185f 100644
--- a/arch/arm/dts/stm32mp157c-ev1.dts
+++ b/arch/arm/dts/stm32mp157c-ev1.dts
@@ -32,7 +32,6 @@
 
 	joystick {
 		compatible = "gpio-keys";
-		#size-cells = <0>;
 		pinctrl-0 = <&joystick_pins>;
 		pinctrl-names = "default";
 		button-0 {
@@ -189,8 +188,8 @@
 		clocks = <&clk_ext_camera>;
 		clock-names = "xclk";
 		DOVDD-supply = <&v2v8>;
-		powerdown-gpios = <&stmfx_pinctrl 18 GPIO_ACTIVE_HIGH>;
-		reset-gpios = <&stmfx_pinctrl 19 GPIO_ACTIVE_LOW>;
+		powerdown-gpios = <&stmfx_pinctrl 18 (GPIO_ACTIVE_HIGH | GPIO_PUSH_PULL)>;
+		reset-gpios = <&stmfx_pinctrl 19 (GPIO_ACTIVE_LOW | GPIO_PUSH_PULL)>;
 		rotation = <180>;
 		status = "okay";
 
@@ -223,7 +222,6 @@
 
 			joystick_pins: joystick {
 				pins = "gpio0", "gpio1", "gpio2", "gpio3", "gpio4";
-				drive-push-pull;
 				bias-pull-down;
 			};
 
@@ -344,14 +342,12 @@
 
 &usbh_ehci {
 	phys = <&usbphyc_port0>;
-	phy-names = "usb";
 	status = "okay";
 };
 
 &usbotg_hs {
 	dr_mode = "peripheral";
 	phys = <&usbphyc_port1 0>;
-	phy-names = "usb2-phy";
 	status = "okay";
 };
 
diff --git a/arch/arm/dts/stm32mp157c.dtsi b/arch/arm/dts/stm32mp157c.dtsi
index 41aea75213..22a9386248 100644
--- a/arch/arm/dts/stm32mp157c.dtsi
+++ b/arch/arm/dts/stm32mp157c.dtsi
@@ -939,7 +939,7 @@
 			interrupt-names = "int0", "int1";
 			clocks = <&rcc CK_HSE>, <&rcc FDCAN_K>;
 			clock-names = "hclk", "cclk";
-			bosch,mram-cfg = <0x1400 0 0 32 0 0 2 2>;
+			bosch,mram-cfg = <0x0 0 0 32 0 0 2 2>;
 			status = "disabled";
 		};
 
@@ -952,7 +952,7 @@
 			interrupt-names = "int0", "int1";
 			clocks = <&rcc CK_HSE>, <&rcc FDCAN_K>;
 			clock-names = "hclk", "cclk";
-			bosch,mram-cfg = <0x0 0 0 32 0 0 2 2>;
+			bosch,mram-cfg = <0x1400 0 0 32 0 0 2 2>;
 			status = "disabled";
 		};
 
@@ -1110,36 +1110,26 @@
 			#reset-cells = <1>;
 		};
 
-		pwr: pwr@50001000 {
-			compatible = "st,stm32mp1-pwr", "st,stm32-pwr", "syscon", "simple-mfd";
-			reg = <0x50001000 0x400>;
-			system-power-controller;
-			interrupts = <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>;
-			st,sysrcc = <&rcc>;
-			clocks = <&rcc PLL2_R>;
-			clock-names = "phyclk";
-
-			pwr-regulators {
-				compatible = "st,stm32mp1,pwr-reg";
-				st,tzcr = <&rcc 0x0 0x1>;
+		pwr_regulators: pwr@50001000 {
+			compatible = "st,stm32mp1,pwr-reg";
+			reg = <0x50001000 0x10>;
 
-				reg11: reg11 {
-					regulator-name = "reg11";
-					regulator-min-microvolt = <1100000>;
-					regulator-max-microvolt = <1100000>;
-				};
+			reg11: reg11 {
+				regulator-name = "reg11";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
+			};
 
-				reg18: reg18 {
-					regulator-name = "reg18";
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-				};
+			reg18: reg18 {
+				regulator-name = "reg18";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
 
-				usb33: usb33 {
-					regulator-name = "usb33";
-					regulator-min-microvolt = <3300000>;
-					regulator-max-microvolt = <3300000>;
-				};
+			usb33: usb33 {
+				regulator-name = "usb33";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
 			};
 		};
 
diff --git a/arch/arm/dts/stm32mp15xx-dhcom-pdk2-u-boot.dtsi b/arch/arm/dts/stm32mp15xx-dhcom-pdk2-u-boot.dtsi
new file mode 100644
index 0000000000..12f89b3398
--- /dev/null
+++ b/arch/arm/dts/stm32mp15xx-dhcom-pdk2-u-boot.dtsi
@@ -0,0 +1,6 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2019 Marek Vasut <marex@denx.de>
+ */
+
+#include "stm32mp15xx-dhcom-u-boot.dtsi"
diff --git a/arch/arm/dts/stm32mp15xx-dhcom-pdk2.dts b/arch/arm/dts/stm32mp15xx-dhcom-pdk2.dts
new file mode 100644
index 0000000000..dd98c7abee
--- /dev/null
+++ b/arch/arm/dts/stm32mp15xx-dhcom-pdk2.dts
@@ -0,0 +1,88 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2019 Marek Vasut <marex@denx.de>
+ */
+
+#include "stm32mp15xx-dhcom.dtsi"
+
+/ {
+	model = "STMicroelectronics STM32MP15xx DHCOM Premium Developer Kit (2)";
+	compatible = "dh,stm32mp15xx-dhcom-pdk2", "st,stm32mp15x";
+
+	aliases {
+		serial0 = &uart4;
+		ethernet0 = &ethernet0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	ethernet_vio: vioregulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vio";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpiog 3 GPIO_ACTIVE_LOW>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+};
+
+&ethernet0 {
+	status = "okay";
+	pinctrl-0 = <&ethernet0_rmii_pins_a>;
+	pinctrl-1 = <&ethernet0_rmii_pins_sleep_a>;
+	pinctrl-names = "default", "sleep";
+	phy-mode = "rmii";
+	max-speed = <100>;
+	phy-handle = <&phy0>;
+	st,eth_ref_clk_sel;
+	phy-reset-gpios = <&gpioh 15 GPIO_ACTIVE_LOW>;
+
+	mdio0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+
+		phy0: ethernet-phy@1 {
+			reg = <1>;
+		};
+	};
+};
+
+&pinctrl {
+	ethernet0_rmii_pins_a: rmii-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('G', 13, AF11)>, /* ETH1_RMII_TXD0 */
+				 <STM32_PINMUX('G', 14, AF11)>, /* ETH1_RMII_TXD1 */
+				 <STM32_PINMUX('B', 11, AF11)>, /* ETH1_RMII_TX_EN */
+				 <STM32_PINMUX('A', 1, AF0)>,   /* ETH1_RMII_REF_CLK */
+				 <STM32_PINMUX('A', 2, AF11)>,  /* ETH1_MDIO */
+				 <STM32_PINMUX('C', 1, AF11)>;  /* ETH1_MDC */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <2>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('C', 4, AF11)>,  /* ETH1_RMII_RXD0 */
+				 <STM32_PINMUX('C', 5, AF11)>,  /* ETH1_RMII_RXD1 */
+				 <STM32_PINMUX('A', 7, AF11)>;  /* ETH1_RMII_CRS_DV */
+			bias-disable;
+		};
+	};
+
+	ethernet0_rmii_pins_sleep_a: rmii-sleep-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('G', 13, ANALOG)>, /* ETH1_RMII_TXD0 */
+				 <STM32_PINMUX('G', 14, ANALOG)>, /* ETH1_RMII_TXD1 */
+				 <STM32_PINMUX('B', 11, ANALOG)>, /* ETH1_RMII_TX_EN */
+				 <STM32_PINMUX('A', 2, ANALOG)>,  /* ETH1_MDIO */
+				 <STM32_PINMUX('C', 1, ANALOG)>,  /* ETH1_MDC */
+				 <STM32_PINMUX('C', 4, ANALOG)>,  /* ETH1_RMII_RXD0 */
+				 <STM32_PINMUX('C', 5, ANALOG)>,  /* ETH1_RMII_RXD1 */
+				 <STM32_PINMUX('A', 1, ANALOG)>,  /* ETH1_RMII_REF_CLK */
+				 <STM32_PINMUX('A', 7, ANALOG)>;  /* ETH1_RMII_CRS_DV */
+		};
+	};
+};
diff --git a/arch/arm/dts/stm32mp15xx-dhcom-u-boot.dtsi b/arch/arm/dts/stm32mp15xx-dhcom-u-boot.dtsi
new file mode 100644
index 0000000000..6c952a57ee
--- /dev/null
+++ b/arch/arm/dts/stm32mp15xx-dhcom-u-boot.dtsi
@@ -0,0 +1,246 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2019 Marek Vasut <marex@denx.de>
+ */
+
+#include <dt-bindings/clock/stm32mp1-clksrc.h>
+#include "stm32mp157-u-boot.dtsi"
+#include "stm32mp15-ddr3-2x4Gb-1066-binG.dtsi"
+
+/ {
+	aliases {
+		i2c1 = &i2c2;
+		i2c3 = &i2c4;
+		i2c4 = &i2c5;
+		mmc0 = &sdmmc1;
+		mmc1 = &sdmmc2;
+		spi0 = &qspi;
+		usb0 = &usbotg_hs;
+	};
+
+	config {
+		u-boot,boot-led = "heartbeat";
+		u-boot,error-led = "error";
+		st,fastboot-gpios = <&gpioa 13 GPIO_ACTIVE_LOW>;
+		st,stm32prog-gpios = <&gpioa 14 GPIO_ACTIVE_LOW>;
+	};
+
+	led {
+		red {
+			label = "error";
+			gpios = <&gpioa 13 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+			status = "okay";
+		};
+
+		blue {
+			default-state = "on";
+		};
+	};
+};
+
+&i2c4 {
+	u-boot,dm-pre-reloc;
+};
+
+&i2c4_pins_a {
+	u-boot,dm-pre-reloc;
+	pins {
+		u-boot,dm-pre-reloc;
+	};
+};
+
+&pmic {
+	u-boot,dm-pre-reloc;
+};
+
+&flash0 {
+	u-boot,dm-spl;
+};
+
+&qspi {
+	u-boot,dm-spl;
+};
+
+&qspi_clk_pins_a {
+	u-boot,dm-spl;
+	pins {
+		u-boot,dm-spl;
+	};
+};
+
+&qspi_bk1_pins_a {
+	u-boot,dm-spl;
+	pins1 {
+		u-boot,dm-spl;
+	};
+	pins2 {
+		u-boot,dm-spl;
+	};
+};
+
+&qspi_bk2_pins_a {
+	u-boot,dm-spl;
+	pins1 {
+		u-boot,dm-spl;
+	};
+	pins2 {
+		u-boot,dm-spl;
+	};
+};
+
+&rcc {
+	st,clksrc = <
+		CLK_MPU_PLL1P
+		CLK_AXI_PLL2P
+		CLK_MCU_PLL3P
+		CLK_PLL12_HSE
+		CLK_PLL3_HSE
+		CLK_PLL4_HSE
+		CLK_RTC_LSE
+		CLK_MCO1_DISABLED
+		CLK_MCO2_DISABLED
+	>;
+
+	st,clkdiv = <
+		1 /*MPU*/
+		0 /*AXI*/
+		0 /*MCU*/
+		1 /*APB1*/
+		1 /*APB2*/
+		1 /*APB3*/
+		1 /*APB4*/
+		2 /*APB5*/
+		23 /*RTC*/
+		0 /*MCO1*/
+		0 /*MCO2*/
+	>;
+
+	st,pkcs = <
+		CLK_CKPER_HSE
+		CLK_FMC_ACLK
+		CLK_QSPI_ACLK
+		CLK_ETH_PLL4P
+		CLK_SDMMC12_PLL4P
+		CLK_DSI_DSIPLL
+		CLK_STGEN_HSE
+		CLK_USBPHY_HSE
+		CLK_SPI2S1_PLL3Q
+		CLK_SPI2S23_PLL3Q
+		CLK_SPI45_HSI
+		CLK_SPI6_HSI
+		CLK_I2C46_HSI
+		CLK_SDMMC3_PLL4P
+		CLK_USBO_USBPHY
+		CLK_ADC_CKPER
+		CLK_CEC_LSE
+		CLK_I2C12_HSI
+		CLK_I2C35_HSI
+		CLK_UART1_HSI
+		CLK_UART24_HSI
+		CLK_UART35_HSI
+		CLK_UART6_HSI
+		CLK_UART78_HSI
+		CLK_SPDIF_PLL4P
+		CLK_FDCAN_PLL4R
+		CLK_SAI1_PLL3Q
+		CLK_SAI2_PLL3Q
+		CLK_SAI3_PLL3Q
+		CLK_SAI4_PLL3Q
+		CLK_RNG1_LSI
+		CLK_RNG2_LSI
+		CLK_LPTIM1_PCLK1
+		CLK_LPTIM23_PCLK3
+		CLK_LPTIM45_LSE
+	>;
+
+	/* VCO = 1300.0 MHz => P = 650 (CPU) */
+	pll1: st,pll@0 {
+		compatible = "st,stm32mp1-pll";
+		reg = <0>;
+		cfg = < 2 80 0 0 0 PQR(1,0,0) >;
+		frac = < 0x800 >;
+		u-boot,dm-pre-reloc;
+	};
+
+	/* VCO = 1066.0 MHz => P = 266 (AXI), Q = 533 (GPU), R = 533 (DDR) */
+	pll2: st,pll@1 {
+		compatible = "st,stm32mp1-pll";
+		reg = <1>;
+		cfg = < 2 65 1 0 0 PQR(1,1,1) >;
+		frac = < 0x1400 >;
+		u-boot,dm-pre-reloc;
+	};
+
+	/* VCO = 417.8 MHz => P = 209, Q = 24, R = 11 */
+	pll3: st,pll@2 {
+		compatible = "st,stm32mp1-pll";
+		reg = <2>;
+		cfg = < 1 33 1 16 36 PQR(1,1,1) >;
+		frac = < 0x1a04 >;
+		u-boot,dm-pre-reloc;
+	};
+
+	/* VCO = 600.0 MHz => P = 50, Q = 50, R = 50 */
+	pll4: st,pll@3 {
+		compatible = "st,stm32mp1-pll";
+		reg = <3>;
+		cfg = < 1 49 11 11 11 PQR(1,1,1) >;
+		u-boot,dm-pre-reloc;
+	};
+};
+
+&sdmmc1 {
+	u-boot,dm-spl;
+};
+
+&sdmmc1_b4_pins_a {
+	u-boot,dm-spl;
+	pins {
+		u-boot,dm-spl;
+	};
+};
+
+&sdmmc1_dir_pins_a {
+	u-boot,dm-spl;
+	pins1 {
+		u-boot,dm-spl;
+	};
+	pins2 {
+		u-boot,dm-spl;
+	};
+};
+
+&sdmmc2 {
+	u-boot,dm-spl;
+};
+
+&sdmmc2_b4_pins_a {
+	u-boot,dm-spl;
+	pins {
+		u-boot,dm-spl;
+	};
+};
+
+&sdmmc2_d47_pins_a {
+	u-boot,dm-spl;
+	pins {
+		u-boot,dm-spl;
+	};
+};
+
+&uart4 {
+	u-boot,dm-pre-reloc;
+};
+
+&uart4_pins_a {
+	u-boot,dm-pre-reloc;
+	pins1 {
+		u-boot,dm-pre-reloc;
+	};
+	pins2 {
+		u-boot,dm-pre-reloc;
+		/* pull-up on rx to avoid floating level */
+		bias-pull-up;
+	};
+};
diff --git a/arch/arm/dts/stm32mp15xx-dhcom.dtsi b/arch/arm/dts/stm32mp15xx-dhcom.dtsi
new file mode 100644
index 0000000000..bed69c97b6
--- /dev/null
+++ b/arch/arm/dts/stm32mp15xx-dhcom.dtsi
@@ -0,0 +1,377 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) 2019 Marek Vasut <marex@denx.de>
+ */
+/dts-v1/;
+
+#include "stm32mp157c.dtsi"
+#include "stm32mp157xaa-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/mfd/st,stpmic1.h>
+
+/ {
+	memory@c0000000 {
+		device_type = "memory";
+		reg = <0xC0000000 0x40000000>;
+	};
+};
+
+&cec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&cec_pins_a>;
+	status = "okay";
+};
+
+&dcmi {
+	status = "okay";
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&dcmi_pins_a>;
+	pinctrl-1 = <&dcmi_sleep_pins_a>;
+};
+
+&dts {
+	status = "okay";
+};
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+};
+
+&i2c4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c4_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	pmic: stpmic@33 {
+		compatible = "st,stpmic1";
+		reg = <0x33>;
+		interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		status = "okay";
+
+		regulators {
+			compatible = "st,stpmic1-regulators";
+			ldo1-supply = <&v3v3>;
+			ldo2-supply = <&v3v3>;
+			ldo3-supply = <&vdd_ddr>;
+			ldo5-supply = <&v3v3>;
+			ldo6-supply = <&v3v3>;
+			pwr_sw1-supply = <&bst_out>;
+			pwr_sw2-supply = <&bst_out>;
+
+			vddcore: buck1 {
+				regulator-name = "vddcore";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			vdd_ddr: buck2 {
+				regulator-name = "vdd_ddr";
+				regulator-min-microvolt = <1350000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			vdd: buck3 {
+				regulator-name = "vdd";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				st,mask-reset;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			v3v3: buck4 {
+				regulator-name = "v3v3";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-over-current-protection;
+				regulator-initial-mode = <0>;
+			};
+
+			vdda: ldo1 {
+				regulator-name = "vdda";
+				regulator-min-microvolt = <2900000>;
+				regulator-max-microvolt = <2900000>;
+				interrupts = <IT_CURLIM_LDO1 0>;
+			};
+
+			v2v8: ldo2 {
+				regulator-name = "v2v8";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+				interrupts = <IT_CURLIM_LDO2 0>;
+			};
+
+			vtt_ddr: ldo3 {
+				regulator-name = "vtt_ddr";
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <750000>;
+				regulator-always-on;
+				regulator-over-current-protection;
+			};
+
+			vdd_usb: ldo4 {
+				regulator-name = "vdd_usb";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				interrupts = <IT_CURLIM_LDO4 0>;
+			};
+
+			vdd_sd: ldo5 {
+				regulator-name = "vdd_sd";
+				regulator-min-microvolt = <2900000>;
+				regulator-max-microvolt = <2900000>;
+				interrupts = <IT_CURLIM_LDO5 0>;
+				regulator-boot-on;
+			};
+
+			v1v8: ldo6 {
+				regulator-name = "v1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				interrupts = <IT_CURLIM_LDO6 0>;
+			};
+
+			vref_ddr: vref_ddr {
+				regulator-name = "vref_ddr";
+				regulator-always-on;
+				regulator-over-current-protection;
+			};
+
+			 bst_out: boost {
+				regulator-name = "bst_out";
+				interrupts = <IT_OCP_BOOST 0>;
+			 };
+
+			vbus_otg: pwr_sw1 {
+				regulator-name = "vbus_otg";
+				interrupts = <IT_OCP_OTG 0>;
+			 };
+
+			 vbus_sw: pwr_sw2 {
+				regulator-name = "vbus_sw";
+				interrupts = <IT_OCP_SWOUT 0>;
+				regulator-active-discharge;
+			 };
+		};
+
+		onkey {
+			compatible = "st,stpmic1-onkey";
+			interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 0>;
+			interrupt-names = "onkey-falling", "onkey-rising";
+			power-off-time-sec = <10>;
+			status = "okay";
+		};
+
+		watchdog {
+			compatible = "st,stpmic1-wdt";
+			status = "disabled";
+		};
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c02";
+		reg = <0x50>;
+		pagesize = <16>;
+	};
+};
+
+&i2c5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c5_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+};
+
+&ipcc {
+	status = "okay";
+};
+
+&iwdg2 {
+	timeout-sec = <32>;
+	status = "okay";
+};
+
+&m4_rproc {
+	mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>;
+	mbox-names = "vq0", "vq1", "shutdown";
+	status = "okay";
+};
+
+&pwr_regulators {
+	vdd-supply = <&vdd>;
+	vdd_3v3_usbfs-supply = <&vdd_usb>;
+};
+
+&qspi {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a &qspi_bk2_pins_a>;
+	pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a &qspi_bk2_sleep_pins_a>;
+	reg = <0x58003000 0x1000>, <0x70000000 0x4000000>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	flash0: mx66l51235l@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <108000000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+	};
+
+	flash1: mx66l51235l@1 {
+		compatible = "jedec,spi-nor";
+		reg = <1>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <108000000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+	};
+};
+
+&rng1 {
+	status = "okay";
+};
+
+&rtc {
+	status = "okay";
+};
+
+&sdmmc1 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_a>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_a>;
+	broken-cd;
+	st,sig-dir;
+	st,neg-edge;
+	st,use-ckin;
+	bus-width = <4>;
+	vmmc-supply = <&vdd_sd>;
+	status = "okay";
+};
+
+&sdmmc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a>;
+	non-removable;
+	no-sd;
+	no-sdio;
+	st,sig-dir;
+	st,neg-edge;
+	bus-width = <8>;
+	vmmc-supply = <&v3v3>;
+	status = "okay";
+};
+
+&spi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi1_pins_a>;
+	status = "disabled";
+};
+
+&timers2 {
+	/* spare dmas for other usage (un-delete to enable pwm capture) */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+	pwm {
+		pinctrl-0 = <&pwm2_pins_a>;
+		pinctrl-names = "default";
+		status = "okay";
+	};
+	timer@1 {
+		status = "okay";
+	};
+};
+
+&timers6 {
+	status = "okay";
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	timer@5 {
+		status = "okay";
+	};
+};
+
+&timers8 {
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+	pwm {
+		pinctrl-0 = <&pwm8_pins_a>;
+		pinctrl-names = "default";
+		status = "okay";
+	};
+	timer@7 {
+		status = "okay";
+	};
+};
+
+&timers12 {
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+	pwm {
+		pinctrl-0 = <&pwm12_pins_a>;
+		pinctrl-names = "default";
+		status = "okay";
+	};
+	timer@11 {
+		status = "okay";
+	};
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart4_pins_a>;
+	status = "okay";
+};
+
+&usbh_ehci {
+	phys = <&usbphyc_port0>;
+	phy-names = "usb";
+	status = "okay";
+};
+
+&usbotg_hs {
+	dr_mode = "peripheral";
+	phys = <&usbphyc_port1 0>;
+	phy-names = "usb2-phy";
+	vbus-supply = <&vbus_otg>;
+	status = "okay";
+};
+
+&usbphyc {
+	status = "okay";
+};
+
+&usbphyc_port0 {
+	phy-supply = <&vdd_usb>;
+};
+
+&usbphyc_port1 {
+	phy-supply = <&vdd_usb>;
+};
diff --git a/arch/arm/mach-stm32mp/Kconfig b/arch/arm/mach-stm32mp/Kconfig
index 137178aa45..e4d621dee8 100644
--- a/arch/arm/mach-stm32mp/Kconfig
+++ b/arch/arm/mach-stm32mp/Kconfig
@@ -73,6 +73,14 @@ config TARGET_ST_STM32MP15x
 		Evalulation board (EV1) or Discovery board (DK1 and DK2).
 		The difference between board are managed with devicetree
 
+config TARGET_DH_STM32MP1_PDK2
+	bool "DH STM32MP1 PDK2"
+	select STM32MP15x
+	imply BOOTCOUNT_LIMIT
+	imply CMD_BOOTCOUNT
+	help
+		Target the DH PDK2 development kit with STM32MP15x SoM.
+
 endchoice
 
 config STM32MP1_TRUSTED
@@ -158,5 +166,6 @@ config DEBUG_UART_CLOCK
 endif
 
 source "board/st/stm32mp1/Kconfig"
+source "board/dhelectronics/dh_stm32mp1/Kconfig"
 
 endif
diff --git a/arch/arm/mach-stm32mp/cpu.c b/arch/arm/mach-stm32mp/cpu.c
index de7891b5c4..ea0bd94605 100644
--- a/arch/arm/mach-stm32mp/cpu.c
+++ b/arch/arm/mach-stm32mp/cpu.c
@@ -342,6 +342,9 @@ int print_cpuinfo(void)
 	case CPU_REVB:
 		cpu_r = "B";
 		break;
+	case CPU_REVZ:
+		cpu_r = "Z";
+		break;
 	default:
 		cpu_r = "?";
 		break;
diff --git a/arch/arm/mach-stm32mp/include/mach/stm32.h b/arch/arm/mach-stm32mp/include/mach/stm32.h
index 88126b8cdb..f0636005e5 100644
--- a/arch/arm/mach-stm32mp/include/mach/stm32.h
+++ b/arch/arm/mach-stm32mp/include/mach/stm32.h
@@ -37,7 +37,6 @@
 /* enumerated used to identify the SYSCON driver instance */
 enum {
 	STM32MP_SYSCON_UNKNOWN,
-	STM32MP_SYSCON_PWR,
 	STM32MP_SYSCON_SYSCFG,
 };
 
diff --git a/arch/arm/mach-stm32mp/include/mach/sys_proto.h b/arch/arm/mach-stm32mp/include/mach/sys_proto.h
index 47e57922d1..da46c11573 100644
--- a/arch/arm/mach-stm32mp/include/mach/sys_proto.h
+++ b/arch/arm/mach-stm32mp/include/mach/sys_proto.h
@@ -16,6 +16,7 @@ u32 get_cpu_type(void);
 
 #define CPU_REVA	0x1000
 #define CPU_REVB	0x2000
+#define CPU_REVZ	0x2001
 
 /* return CPU_REV constants */
 u32 get_cpu_rev(void);
diff --git a/arch/arm/mach-stm32mp/pwr_regulator.c b/arch/arm/mach-stm32mp/pwr_regulator.c
index 4559ef599d..b52e1e85d5 100644
--- a/arch/arm/mach-stm32mp/pwr_regulator.c
+++ b/arch/arm/mach-stm32mp/pwr_regulator.c
@@ -6,8 +6,8 @@
 #include <common.h>
 #include <dm.h>
 #include <errno.h>
-#include <regmap.h>
 #include <syscon.h>
+#include <asm/io.h>
 #include <dm/device_compat.h>
 #include <linux/err.h>
 #include <power/pmic.h>
@@ -28,7 +28,7 @@ struct stm32mp_pwr_reg_info {
 };
 
 struct stm32mp_pwr_priv {
-	struct regmap *regmap;
+	fdt_addr_t base;
 };
 
 static int stm32mp_pwr_write(struct udevice *dev, uint reg,
@@ -40,7 +40,9 @@ static int stm32mp_pwr_write(struct udevice *dev, uint reg,
 	if (len != 4)
 		return -EINVAL;
 
-	return regmap_write(priv->regmap, STM32MP_PWR_CR3, val);
+	writel(val, priv->base + STM32MP_PWR_CR3);
+
+	return 0;
 }
 
 static int stm32mp_pwr_read(struct udevice *dev, uint reg, uint8_t *buff,
@@ -51,21 +53,18 @@ static int stm32mp_pwr_read(struct udevice *dev, uint reg, uint8_t *buff,
 	if (len != 4)
 		return -EINVAL;
 
-	return regmap_read(priv->regmap, STM32MP_PWR_CR3, (u32 *)buff);
+	*(u32 *)buff = readl(priv->base + STM32MP_PWR_CR3);
+
+	return 0;
 }
 
 static int stm32mp_pwr_ofdata_to_platdata(struct udevice *dev)
 {
 	struct stm32mp_pwr_priv *priv = dev_get_priv(dev);
-	struct regmap *regmap;
 
-	regmap = syscon_get_regmap_by_driver_data(STM32MP_SYSCON_PWR);
-	if (IS_ERR(regmap)) {
-		pr_err("%s: unable to find regmap (%ld)\n", __func__,
-		       PTR_ERR(regmap));
-		return PTR_ERR(regmap);
-	}
-	priv->regmap = regmap;
+	priv->base = dev_read_addr(dev);
+	if (priv->base == FDT_ADDR_T_NONE)
+		return -EINVAL;
 
 	return 0;
 }
diff --git a/arch/arm/mach-stm32mp/syscon.c b/arch/arm/mach-stm32mp/syscon.c
index 6070837bf0..3e61ce4097 100644
--- a/arch/arm/mach-stm32mp/syscon.c
+++ b/arch/arm/mach-stm32mp/syscon.c
@@ -9,7 +9,6 @@
 #include <asm/arch/stm32.h>
 
 static const struct udevice_id stm32mp_syscon_ids[] = {
-	{ .compatible = "st,stm32mp1-pwr", .data = STM32MP_SYSCON_PWR },
 	{ .compatible = "st,stm32mp157-syscfg",
 	  .data = STM32MP_SYSCON_SYSCFG },
 	{ }
diff --git a/board/dhelectronics/dh_stm32mp1/Kconfig b/board/dhelectronics/dh_stm32mp1/Kconfig
new file mode 100644
index 0000000000..8eab986640
--- /dev/null
+++ b/board/dhelectronics/dh_stm32mp1/Kconfig
@@ -0,0 +1,21 @@
+if TARGET_DH_STM32MP1_PDK2
+
+config SYS_BOARD
+	default "dh_stm32mp1"
+
+config SYS_VENDOR
+	default "dhelectronics"
+
+config SYS_CONFIG_NAME
+	default "stm32mp1"
+
+config ENV_SECT_SIZE
+	default 0x10000 if ENV_IS_IN_SPI_FLASH
+
+config ENV_OFFSET
+	default 0x1E0000 if ENV_IS_IN_SPI_FLASH
+
+config ENV_OFFSET_REDUND
+	default 0x1F0000 if ENV_IS_IN_SPI_FLASH
+
+endif
diff --git a/board/dhelectronics/dh_stm32mp1/MAINTAINERS b/board/dhelectronics/dh_stm32mp1/MAINTAINERS
new file mode 100644
index 0000000000..1511ecb65d
--- /dev/null
+++ b/board/dhelectronics/dh_stm32mp1/MAINTAINERS
@@ -0,0 +1,7 @@
+DH_STM32MP1_PDK2 BOARD
+M:	Marek Vasut <marex@denx.de>
+S:	Maintained
+F:	arch/arm/dts/stm32mp15xx-dhcom*
+F:	board/dhelectronics/dh_stm32mp1/
+F:	configs/stm32mp15_dhcom_basic_defconfig
+F:	include/configs/stm32mp1.h
diff --git a/board/dhelectronics/dh_stm32mp1/Makefile b/board/dhelectronics/dh_stm32mp1/Makefile
new file mode 100644
index 0000000000..b42c4e4c04
--- /dev/null
+++ b/board/dhelectronics/dh_stm32mp1/Makefile
@@ -0,0 +1,10 @@
+# SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+#
+# Copyright (C) 2018, STMicroelectronics - All Rights Reserved
+#
+
+ifdef CONFIG_SPL_BUILD
+obj-y += ../../st/stm32mp1/spl.o
+endif
+
+obj-y += ../../st/stm32mp1/board.o board.o
diff --git a/board/dhelectronics/dh_stm32mp1/board.c b/board/dhelectronics/dh_stm32mp1/board.c
new file mode 100644
index 0000000000..b663696983
--- /dev/null
+++ b/board/dhelectronics/dh_stm32mp1/board.c
@@ -0,0 +1,689 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2018, STMicroelectronics - All Rights Reserved
+ */
+
+#include <common.h>
+#include <adc.h>
+#include <asm/arch/stm32.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/gpio.h>
+#include <asm/io.h>
+#include <bootm.h>
+#include <clk.h>
+#include <config.h>
+#include <dm.h>
+#include <dm/device.h>
+#include <dm/uclass.h>
+#include <env.h>
+#include <env_internal.h>
+#include <g_dnl.h>
+#include <generic-phy.h>
+#include <hang.h>
+#include <i2c.h>
+#include <i2c_eeprom.h>
+#include <init.h>
+#include <led.h>
+#include <memalign.h>
+#include <misc.h>
+#include <mtd.h>
+#include <mtd_node.h>
+#include <netdev.h>
+#include <phy.h>
+#include <power/regulator.h>
+#include <remoteproc.h>
+#include <reset.h>
+#include <syscon.h>
+#include <usb.h>
+#include <usb/dwc2_udc.h>
+#include <watchdog.h>
+
+/* SYSCFG registers */
+#define SYSCFG_BOOTR		0x00
+#define SYSCFG_PMCSETR		0x04
+#define SYSCFG_IOCTRLSETR	0x18
+#define SYSCFG_ICNR		0x1C
+#define SYSCFG_CMPCR		0x20
+#define SYSCFG_CMPENSETR	0x24
+#define SYSCFG_PMCCLRR		0x44
+
+#define SYSCFG_BOOTR_BOOT_MASK		GENMASK(2, 0)
+#define SYSCFG_BOOTR_BOOTPD_SHIFT	4
+
+#define SYSCFG_IOCTRLSETR_HSLVEN_TRACE		BIT(0)
+#define SYSCFG_IOCTRLSETR_HSLVEN_QUADSPI	BIT(1)
+#define SYSCFG_IOCTRLSETR_HSLVEN_ETH		BIT(2)
+#define SYSCFG_IOCTRLSETR_HSLVEN_SDMMC		BIT(3)
+#define SYSCFG_IOCTRLSETR_HSLVEN_SPI		BIT(4)
+
+#define SYSCFG_CMPCR_SW_CTRL		BIT(1)
+#define SYSCFG_CMPCR_READY		BIT(8)
+
+#define SYSCFG_CMPENSETR_MPU_EN		BIT(0)
+
+#define SYSCFG_PMCSETR_ETH_CLK_SEL	BIT(16)
+#define SYSCFG_PMCSETR_ETH_REF_CLK_SEL	BIT(17)
+
+#define SYSCFG_PMCSETR_ETH_SELMII	BIT(20)
+
+#define SYSCFG_PMCSETR_ETH_SEL_MASK	GENMASK(23, 21)
+#define SYSCFG_PMCSETR_ETH_SEL_GMII_MII	0
+#define SYSCFG_PMCSETR_ETH_SEL_RGMII	BIT(21)
+#define SYSCFG_PMCSETR_ETH_SEL_RMII	BIT(23)
+
+/*
+ * Get a global data pointer
+ */
+DECLARE_GLOBAL_DATA_PTR;
+
+int setup_mac_address(void)
+{
+	struct udevice *dev;
+	ofnode eeprom;
+	unsigned char enetaddr[6];
+	int ret;
+
+	ret = eth_env_get_enetaddr("ethaddr", enetaddr);
+	if (ret)	/* ethaddr is already set */
+		return 0;
+
+	eeprom = ofnode_path("/soc/i2c@5c002000/eeprom@50");
+	if (!ofnode_valid(eeprom)) {
+		printf("Invalid hardware path to EEPROM!\n");
+		return -ENODEV;
+	}
+
+	ret = uclass_get_device_by_ofnode(UCLASS_I2C_EEPROM, eeprom, &dev);
+	if (ret) {
+		printf("Cannot find EEPROM!\n");
+		return ret;
+	}
+
+	ret = i2c_eeprom_read(dev, 0xfa, enetaddr, 0x6);
+	if (ret) {
+		printf("Error reading configuration EEPROM!\n");
+		return ret;
+	}
+
+	if (is_valid_ethaddr(enetaddr))
+		eth_env_set_enetaddr("ethaddr", enetaddr);
+
+	return 0;
+}
+
+int checkboard(void)
+{
+	char *mode;
+	const char *fdt_compat;
+	int fdt_compat_len;
+
+	if (IS_ENABLED(CONFIG_STM32MP1_OPTEE))
+		mode = "trusted with OP-TEE";
+	else if (IS_ENABLED(CONFIG_STM32MP1_TRUSTED))
+		mode = "trusted";
+	else
+		mode = "basic";
+
+	printf("Board: stm32mp1 in %s mode", mode);
+	fdt_compat = fdt_getprop(gd->fdt_blob, 0, "compatible",
+				 &fdt_compat_len);
+	if (fdt_compat && fdt_compat_len)
+		printf(" (%s)", fdt_compat);
+	puts("\n");
+
+	return 0;
+}
+
+static void board_key_check(void)
+{
+#if defined(CONFIG_FASTBOOT) || defined(CONFIG_CMD_STM32PROG)
+	ofnode node;
+	struct gpio_desc gpio;
+	enum forced_boot_mode boot_mode = BOOT_NORMAL;
+
+	node = ofnode_path("/config");
+	if (!ofnode_valid(node)) {
+		debug("%s: no /config node?\n", __func__);
+		return;
+	}
+#ifdef CONFIG_FASTBOOT
+	if (gpio_request_by_name_nodev(node, "st,fastboot-gpios", 0,
+				       &gpio, GPIOD_IS_IN)) {
+		debug("%s: could not find a /config/st,fastboot-gpios\n",
+		      __func__);
+	} else {
+		if (dm_gpio_get_value(&gpio)) {
+			puts("Fastboot key pressed, ");
+			boot_mode = BOOT_FASTBOOT;
+		}
+
+		dm_gpio_free(NULL, &gpio);
+	}
+#endif
+#ifdef CONFIG_CMD_STM32PROG
+	if (gpio_request_by_name_nodev(node, "st,stm32prog-gpios", 0,
+				       &gpio, GPIOD_IS_IN)) {
+		debug("%s: could not find a /config/st,stm32prog-gpios\n",
+		      __func__);
+	} else {
+		if (dm_gpio_get_value(&gpio)) {
+			puts("STM32Programmer key pressed, ");
+			boot_mode = BOOT_STM32PROG;
+		}
+		dm_gpio_free(NULL, &gpio);
+	}
+#endif
+
+	if (boot_mode != BOOT_NORMAL) {
+		puts("entering download mode...\n");
+		clrsetbits_le32(TAMP_BOOT_CONTEXT,
+				TAMP_BOOT_FORCED_MASK,
+				boot_mode);
+	}
+#endif
+}
+
+#if defined(CONFIG_USB_GADGET) && defined(CONFIG_USB_GADGET_DWC2_OTG)
+
+#include <usb/dwc2_udc.h>
+int g_dnl_board_usb_cable_connected(void)
+{
+	struct udevice *dwc2_udc_otg;
+	int ret;
+
+	ret = uclass_get_device_by_driver(UCLASS_USB_GADGET_GENERIC,
+					  DM_GET_DRIVER(dwc2_udc_otg),
+					  &dwc2_udc_otg);
+	if (!ret)
+		debug("dwc2_udc_otg init failed\n");
+
+	return dwc2_udc_B_session_valid(dwc2_udc_otg);
+}
+
+#define STM32MP1_G_DNL_DFU_PRODUCT_NUM 0xdf11
+#define STM32MP1_G_DNL_FASTBOOT_PRODUCT_NUM 0x0afb
+
+int g_dnl_bind_fixup(struct usb_device_descriptor *dev, const char *name)
+{
+	if (!strcmp(name, "usb_dnl_dfu"))
+		put_unaligned(STM32MP1_G_DNL_DFU_PRODUCT_NUM, &dev->idProduct);
+	else if (!strcmp(name, "usb_dnl_fastboot"))
+		put_unaligned(STM32MP1_G_DNL_FASTBOOT_PRODUCT_NUM,
+			      &dev->idProduct);
+	else
+		put_unaligned(CONFIG_USB_GADGET_PRODUCT_NUM, &dev->idProduct);
+
+	return 0;
+}
+
+#endif /* CONFIG_USB_GADGET */
+
+#ifdef CONFIG_LED
+static int get_led(struct udevice **dev, char *led_string)
+{
+	char *led_name;
+	int ret;
+
+	led_name = fdtdec_get_config_string(gd->fdt_blob, led_string);
+	if (!led_name) {
+		pr_debug("%s: could not find %s config string\n",
+			 __func__, led_string);
+		return -ENOENT;
+	}
+	ret = led_get_by_label(led_name, dev);
+	if (ret) {
+		debug("%s: get=%d\n", __func__, ret);
+		return ret;
+	}
+
+	return 0;
+}
+
+static int setup_led(enum led_state_t cmd)
+{
+	struct udevice *dev;
+	int ret;
+
+	ret = get_led(&dev, "u-boot,boot-led");
+	if (ret)
+		return ret;
+
+	ret = led_set_state(dev, cmd);
+	return ret;
+}
+#endif
+
+static void __maybe_unused led_error_blink(u32 nb_blink)
+{
+#ifdef CONFIG_LED
+	int ret;
+	struct udevice *led;
+	u32 i;
+#endif
+
+	if (!nb_blink)
+		return;
+
+#ifdef CONFIG_LED
+	ret = get_led(&led, "u-boot,error-led");
+	if (!ret) {
+		/* make u-boot,error-led blinking */
+		/* if U32_MAX and 125ms interval, for 17.02 years */
+		for (i = 0; i < 2 * nb_blink; i++) {
+			led_set_state(led, LEDST_TOGGLE);
+			mdelay(125);
+			WATCHDOG_RESET();
+		}
+	}
+#endif
+
+	/* infinite: the boot process must be stopped */
+	if (nb_blink == U32_MAX)
+		hang();
+}
+
+static void sysconf_init(void)
+{
+#ifndef CONFIG_STM32MP1_TRUSTED
+	u8 *syscfg;
+#ifdef CONFIG_DM_REGULATOR
+	struct udevice *pwr_dev;
+	struct udevice *pwr_reg;
+	struct udevice *dev;
+	int ret;
+	u32 otp = 0;
+#endif
+	u32 bootr;
+
+	syscfg = (u8 *)syscon_get_first_range(STM32MP_SYSCON_SYSCFG);
+
+	/* interconnect update : select master using the port 1 */
+	/* LTDC = AXI_M9 */
+	/* GPU  = AXI_M8 */
+	/* today information is hardcoded in U-Boot */
+	writel(BIT(9), syscfg + SYSCFG_ICNR);
+
+	/* disable Pull-Down for boot pin connected to VDD */
+	bootr = readl(syscfg + SYSCFG_BOOTR);
+	bootr &= ~(SYSCFG_BOOTR_BOOT_MASK << SYSCFG_BOOTR_BOOTPD_SHIFT);
+	bootr |= (bootr & SYSCFG_BOOTR_BOOT_MASK) << SYSCFG_BOOTR_BOOTPD_SHIFT;
+	writel(bootr, syscfg + SYSCFG_BOOTR);
+
+#ifdef CONFIG_DM_REGULATOR
+	/* High Speed Low Voltage Pad mode Enable for SPI, SDMMC, ETH, QSPI
+	 * and TRACE. Needed above ~50MHz and conditioned by AFMUX selection.
+	 * The customer will have to disable this for low frequencies
+	 * or if AFMUX is selected but the function not used, typically for
+	 * TRACE. Otherwise, impact on power consumption.
+	 *
+	 * WARNING:
+	 *   enabling High Speed mode while VDD>2.7V
+	 *   with the OTP product_below_2v5 (OTP 18, BIT 13)
+	 *   erroneously set to 1 can damage the IC!
+	 *   => U-Boot set the register only if VDD < 2.7V (in DT)
+	 *      but this value need to be consistent with board design
+	 */
+	ret = uclass_get_device_by_driver(UCLASS_PMIC,
+					  DM_GET_DRIVER(stm32mp_pwr_pmic),
+					  &pwr_dev);
+	if (!ret) {
+		ret = uclass_get_device_by_driver(UCLASS_MISC,
+						  DM_GET_DRIVER(stm32mp_bsec),
+						  &dev);
+		if (ret) {
+			pr_err("Can't find stm32mp_bsec driver\n");
+			return;
+		}
+
+		ret = misc_read(dev, STM32_BSEC_SHADOW(18), &otp, 4);
+		if (ret > 0)
+			otp = otp & BIT(13);
+
+		/* get VDD = vdd-supply */
+		ret = device_get_supply_regulator(pwr_dev, "vdd-supply",
+						  &pwr_reg);
+
+		/* check if VDD is Low Voltage */
+		if (!ret) {
+			if (regulator_get_value(pwr_reg) < 2700000) {
+				writel(SYSCFG_IOCTRLSETR_HSLVEN_TRACE |
+				       SYSCFG_IOCTRLSETR_HSLVEN_QUADSPI |
+				       SYSCFG_IOCTRLSETR_HSLVEN_ETH |
+				       SYSCFG_IOCTRLSETR_HSLVEN_SDMMC |
+				       SYSCFG_IOCTRLSETR_HSLVEN_SPI,
+				       syscfg + SYSCFG_IOCTRLSETR);
+
+				if (!otp)
+					pr_err("product_below_2v5=0: HSLVEN protected by HW\n");
+			} else {
+				if (otp)
+					pr_err("product_below_2v5=1: HSLVEN update is destructive, no update as VDD>2.7V\n");
+			}
+		} else {
+			debug("VDD unknown");
+		}
+	}
+#endif
+
+	/* activate automatic I/O compensation
+	 * warning: need to ensure CSI enabled and ready in clock driver
+	 */
+	writel(SYSCFG_CMPENSETR_MPU_EN, syscfg + SYSCFG_CMPENSETR);
+
+	while (!(readl(syscfg + SYSCFG_CMPCR) & SYSCFG_CMPCR_READY))
+		;
+	clrbits_le32(syscfg + SYSCFG_CMPCR, SYSCFG_CMPCR_SW_CTRL);
+#endif
+}
+
+/* board dependent setup after realloc */
+int board_init(void)
+{
+	struct udevice *dev;
+
+	/* address of boot parameters */
+	gd->bd->bi_boot_params = STM32_DDR_BASE + 0x100;
+
+	/* probe all PINCTRL for hog */
+	for (uclass_first_device(UCLASS_PINCTRL, &dev);
+	     dev;
+	     uclass_next_device(&dev)) {
+		pr_debug("probe pincontrol = %s\n", dev->name);
+	}
+
+	board_key_check();
+
+#ifdef CONFIG_DM_REGULATOR
+	regulators_enable_boot_on(_DEBUG);
+#endif
+
+	sysconf_init();
+
+	if (CONFIG_IS_ENABLED(CONFIG_LED))
+		led_default_state();
+
+	return 0;
+}
+
+int board_late_init(void)
+{
+	char *boot_device;
+#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
+	const void *fdt_compat;
+	int fdt_compat_len;
+
+	fdt_compat = fdt_getprop(gd->fdt_blob, 0, "compatible",
+				 &fdt_compat_len);
+	if (fdt_compat && fdt_compat_len) {
+		if (strncmp(fdt_compat, "st,", 3) != 0)
+			env_set("board_name", fdt_compat);
+		else
+			env_set("board_name", fdt_compat + 3);
+	}
+#endif
+
+	/* Check the boot-source to disable bootdelay */
+	boot_device = env_get("boot_device");
+	if (!strcmp(boot_device, "serial") || !strcmp(boot_device, "usb"))
+		env_set("bootdelay", "0");
+
+	return 0;
+}
+
+void board_quiesce_devices(void)
+{
+#ifdef CONFIG_LED
+	setup_led(LEDST_OFF);
+#endif
+}
+
+/* eth init function : weak called in eqos driver */
+int board_interface_eth_init(struct udevice *dev,
+			     phy_interface_t interface_type)
+{
+	u8 *syscfg;
+	u32 value;
+	bool eth_clk_sel_reg = false;
+	bool eth_ref_clk_sel_reg = false;
+
+	/* Gigabit Ethernet 125MHz clock selection. */
+	eth_clk_sel_reg = dev_read_bool(dev, "st,eth_clk_sel");
+
+	/* Ethernet 50Mhz RMII clock selection */
+	eth_ref_clk_sel_reg =
+		dev_read_bool(dev, "st,eth_ref_clk_sel");
+
+	syscfg = (u8 *)syscon_get_first_range(STM32MP_SYSCON_SYSCFG);
+
+	if (!syscfg)
+		return -ENODEV;
+
+	switch (interface_type) {
+	case PHY_INTERFACE_MODE_MII:
+		value = SYSCFG_PMCSETR_ETH_SEL_GMII_MII |
+			SYSCFG_PMCSETR_ETH_REF_CLK_SEL;
+		debug("%s: PHY_INTERFACE_MODE_MII\n", __func__);
+		break;
+	case PHY_INTERFACE_MODE_GMII:
+		if (eth_clk_sel_reg)
+			value = SYSCFG_PMCSETR_ETH_SEL_GMII_MII |
+				SYSCFG_PMCSETR_ETH_CLK_SEL;
+		else
+			value = SYSCFG_PMCSETR_ETH_SEL_GMII_MII;
+		debug("%s: PHY_INTERFACE_MODE_GMII\n", __func__);
+		break;
+	case PHY_INTERFACE_MODE_RMII:
+		if (eth_ref_clk_sel_reg)
+			value = SYSCFG_PMCSETR_ETH_SEL_RMII |
+				SYSCFG_PMCSETR_ETH_REF_CLK_SEL;
+		else
+			value = SYSCFG_PMCSETR_ETH_SEL_RMII;
+		debug("%s: PHY_INTERFACE_MODE_RMII\n", __func__);
+		break;
+	case PHY_INTERFACE_MODE_RGMII:
+	case PHY_INTERFACE_MODE_RGMII_ID:
+	case PHY_INTERFACE_MODE_RGMII_RXID:
+	case PHY_INTERFACE_MODE_RGMII_TXID:
+		if (eth_clk_sel_reg)
+			value = SYSCFG_PMCSETR_ETH_SEL_RGMII |
+				SYSCFG_PMCSETR_ETH_CLK_SEL;
+		else
+			value = SYSCFG_PMCSETR_ETH_SEL_RGMII;
+		debug("%s: PHY_INTERFACE_MODE_RGMII\n", __func__);
+		break;
+	default:
+		debug("%s: Do not manage %d interface\n",
+		      __func__, interface_type);
+		/* Do not manage others interfaces */
+		return -EINVAL;
+	}
+
+	/* clear and set ETH configuration bits */
+	writel(SYSCFG_PMCSETR_ETH_SEL_MASK | SYSCFG_PMCSETR_ETH_SELMII |
+	       SYSCFG_PMCSETR_ETH_REF_CLK_SEL | SYSCFG_PMCSETR_ETH_CLK_SEL,
+	       syscfg + SYSCFG_PMCCLRR);
+	writel(value, syscfg + SYSCFG_PMCSETR);
+
+	return 0;
+}
+
+enum env_location env_get_location(enum env_operation op, int prio)
+{
+	if (prio)
+		return ENVL_UNKNOWN;
+
+#ifdef CONFIG_ENV_IS_IN_SPI_FLASH
+	return ENVL_SPI_FLASH;
+#else
+	return ENVL_NOWHERE;
+#endif
+}
+
+#ifdef CONFIG_SYS_MTDPARTS_RUNTIME
+
+#define MTDPARTS_LEN		256
+#define MTDIDS_LEN		128
+
+/**
+ * The mtdparts_nand0 and mtdparts_nor0 variable tends to be long.
+ * If we need to access it before the env is relocated, then we need
+ * to use our own stack buffer. gd->env_buf will be too small.
+ *
+ * @param buf temporary buffer pointer MTDPARTS_LEN long
+ * @return mtdparts variable string, NULL if not found
+ */
+static const char *env_get_mtdparts(const char *str, char *buf)
+{
+	if (gd->flags & GD_FLG_ENV_READY)
+		return env_get(str);
+	if (env_get_f(str, buf, MTDPARTS_LEN) != -1)
+		return buf;
+
+	return NULL;
+}
+
+/**
+ * update the variables "mtdids" and "mtdparts" with content of mtdparts_<dev>
+ */
+static void board_get_mtdparts(const char *dev,
+			       char *mtdids,
+			       char *mtdparts)
+{
+	char env_name[32] = "mtdparts_";
+	char tmp_mtdparts[MTDPARTS_LEN];
+	const char *tmp;
+
+	/* name of env variable to read = mtdparts_<dev> */
+	strcat(env_name, dev);
+	tmp = env_get_mtdparts(env_name, tmp_mtdparts);
+	if (tmp) {
+		/* mtdids: "<dev>=<dev>, ...." */
+		if (mtdids[0] != '\0')
+			strcat(mtdids, ",");
+		strcat(mtdids, dev);
+		strcat(mtdids, "=");
+		strcat(mtdids, dev);
+
+		/* mtdparts: "mtdparts=<dev>:<mtdparts_<dev>>;..." */
+		if (mtdparts[0] != '\0')
+			strncat(mtdparts, ";", MTDPARTS_LEN);
+		else
+			strcat(mtdparts, "mtdparts=");
+		strncat(mtdparts, dev, MTDPARTS_LEN);
+		strncat(mtdparts, ":", MTDPARTS_LEN);
+		strncat(mtdparts, tmp, MTDPARTS_LEN);
+	}
+}
+
+void board_mtdparts_default(const char **mtdids, const char **mtdparts)
+{
+	struct udevice *dev;
+	static char parts[3 * MTDPARTS_LEN + 1];
+	static char ids[MTDIDS_LEN + 1];
+	static bool mtd_initialized;
+
+	if (mtd_initialized) {
+		*mtdids = ids;
+		*mtdparts = parts;
+		return;
+	}
+
+	memset(parts, 0, sizeof(parts));
+	memset(ids, 0, sizeof(ids));
+
+	/* probe all MTD devices */
+	for (uclass_first_device(UCLASS_MTD, &dev);
+	     dev;
+	     uclass_next_device(&dev)) {
+		pr_debug("mtd device = %s\n", dev->name);
+	}
+
+	if (!uclass_get_device(UCLASS_SPI_FLASH, 0, &dev))
+		board_get_mtdparts("nor0", ids, parts);
+
+	mtd_initialized = true;
+	*mtdids = ids;
+	*mtdparts = parts;
+	debug("%s:mtdids=%s & mtdparts=%s\n", __func__, ids, parts);
+}
+#endif
+
+#if defined(CONFIG_OF_BOARD_SETUP)
+int ft_board_setup(void *blob, bd_t *bd)
+{
+	return 0;
+}
+#endif
+
+#ifdef CONFIG_SET_DFU_ALT_INFO
+#define DFU_ALT_BUF_LEN SZ_1K
+
+static void board_get_alt_info(const char *dev, char *buff)
+{
+	char var_name[32] = "dfu_alt_info_";
+	int ret;
+
+	ALLOC_CACHE_ALIGN_BUFFER(char, tmp_alt, DFU_ALT_BUF_LEN);
+
+	/* name of env variable to read = dfu_alt_info_<dev> */
+	strcat(var_name, dev);
+	ret = env_get_f(var_name, tmp_alt, DFU_ALT_BUF_LEN);
+	if (ret) {
+		if (buff[0] != '\0')
+			strcat(buff, "&");
+		strncat(buff, tmp_alt, DFU_ALT_BUF_LEN);
+	}
+}
+
+void set_dfu_alt_info(char *interface, char *devstr)
+{
+	struct udevice *dev;
+
+	ALLOC_CACHE_ALIGN_BUFFER(char, buf, DFU_ALT_BUF_LEN);
+
+	if (env_get("dfu_alt_info"))
+		return;
+
+	memset(buf, 0, sizeof(buf));
+
+	/* probe all MTD devices */
+	mtd_probe_devices();
+
+	board_get_alt_info("ram", buf);
+
+	if (!uclass_get_device(UCLASS_MMC, 0, &dev))
+		board_get_alt_info("mmc0", buf);
+
+	if (!uclass_get_device(UCLASS_MMC, 1, &dev))
+		board_get_alt_info("mmc1", buf);
+
+	if (!uclass_get_device(UCLASS_SPI_FLASH, 0, &dev))
+		board_get_alt_info("nor0", buf);
+
+	env_set("dfu_alt_info", buf);
+	puts("DFU alt info setting: done\n");
+}
+#endif
+
+static void board_copro_image_process(ulong fw_image, size_t fw_size)
+{
+	int ret, id = 0; /* Copro id fixed to 0 as only one coproc on mp1 */
+
+	if (!rproc_is_initialized())
+		if (rproc_init()) {
+			printf("Remote Processor %d initialization failed\n",
+			       id);
+			return;
+		}
+
+	ret = rproc_load(id, fw_image, fw_size);
+	printf("Load Remote Processor %d with data@addr=0x%08lx %u bytes:%s\n",
+	       id, fw_image, fw_size, ret ? " Failed!" : " Success!");
+
+	if (!ret) {
+		rproc_start(id);
+		env_set("copro_state", "booted");
+	}
+}
+
+U_BOOT_FIT_LOADABLE_HANDLER(IH_TYPE_COPRO, board_copro_image_process);
diff --git a/board/st/stm32mp1/README b/board/st/stm32mp1/README
index f2069bcefa..5d7465a8c8 100644
--- a/board/st/stm32mp1/README
+++ b/board/st/stm32mp1/README
@@ -3,8 +3,8 @@ SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
 # Copyright (C) 2018 STMicroelectronics - All Rights Reserved
 #
 
-U-Boot on STMicroelectronics STM32MP1
-======================================
+U-Boot on STMicroelectronics STM32MP15x
+=======================================
 
 1. Summary
 ==========
@@ -12,12 +12,12 @@ This is a quick instruction for setup stm32mp1 boards.
 
 2. Supported devices
 ====================
-U-Boot supports one STMP32MP1 SoCs: STM32MP157
+U-Boot supports STMP32MP15x SoCs: STM32MP157, STM32MP153 and STM32MP151
 
-The STM32MP157 is a Cortex-A MPU aimed at various applications.
+The STM32MP15x is a Cortex-A MPU aimed at various applications.
 It features:
-- Dual core Cortex-A7 application core
-- 2D/3D image composition with GPU
+- Dual core Cortex-A7 application core (Single on STM32MP151)
+- 2D/3D image composition with GPU (only on STM32MP157)
 - Standard memories interface support
 - Standard connectivity, widely inherited from the STM32 MCU family
 - Comprehensive security support
@@ -37,11 +37,11 @@ And the necessary drivers
 4. Fuse
 
 Currently the following boards are supported:
-+ stm32mp157c-ev1
-+ stm32mp157c-ed1
-+ stm32mp157a-dk1
-+ stm32mp157c-dk2
-+ stm32mp157a-avenger96
++ stm32mp157a-avenger96.dts
++ stm32mp157a-dk1.dts
++ stm32mp157c-dk2.dts
++ stm32mp157c-ed1.dts
++ stm32mp157c-ev1.dts
 
 3. Boot Sequences
 =================
@@ -74,7 +74,7 @@ with FSBL = First Stage Bootloader
    U-Boot is running in secure mode and provide a secure monitor to the kernel
    with only PSCI support (Power State Coordination Interface defined by ARM).
 
-All the STM32MP1 boards supported by U-Boot use the same generic board
+All the STM32MP15x boards supported by U-Boot use the same generic board
 stm32mp1 which support all the bootable devices.
 
 Each board is configurated only with the associated device tree.
@@ -108,7 +108,7 @@ the supported device trees for stm32mp157 are:
    + install package needed in U-Boot makefile
      (libssl-dev, swig, libpython-dev...)
    + install ARMv7 toolchain for 32bit Cortex-A (from Linaro,
-     from SDK for STM32MP1, or any crosstoolchains from your distribution)
+     from SDK for STM32MP15x, or any crosstoolchains from your distribution)
 
 2. Set the cross compiler:
 
@@ -323,8 +323,7 @@ c) copy U-Boot in first GPT partition of eMMC
 	# ext4load mmc 0:4 0xC0000000 u-boot.img
 	# mmc dev 1
 	# part start mmc 1 1 partstart
-	# part size mmc 1 1 partsize
-	# mmc write ${fileaddr} ${partstart} ${partsize}
+	# mmc write ${fileaddr} ${partstart} ${filesize}
 
 To boot from eMMC, select BootPinMode = 0 1 0 and reset.
 
@@ -334,14 +333,27 @@ To boot from eMMC, select BootPinMode = 0 1 0 and reset.
 Please read doc/README.enetaddr for the implementation guidelines for mac id
 usage. Basically, environment has precedence over board specific storage.
 
-Mac id storage and retrieval in stm32mp otp :
+For STMicroelectonics board, it is retrieved in STM32MP15x otp :
 - OTP_57[31:0] = MAC_ADDR[31:0]
 - OTP_58[15:0] = MAC_ADDR[47:32]
 
 To program a MAC address on virgin OTP words above, you can use the fuse command
 on bank 0 to access to internal OTP:
 
-    example to set mac address "12:34:56:78:9a:bc"
+    Prerequisite: check if a MAC address isn't yet programmed in OTP
+
+    1- check OTP: their value must be equal to 0
+
+       STM32MP> fuse sense 0 57 2
+       Sensing bank 0:
+       Word 0x00000039: 00000000 00000000
+
+    2- check environment variable
+
+       STM32MP> env print ethaddr
+       ## Error: "ethaddr" not defined
+
+    Example to set mac address "12:34:56:78:9a:bc"
 
     1- Write OTP
        STM32MP> fuse prog -y 0 57 0x78563412 0x0000bc9a
@@ -355,9 +367,13 @@ on bank 0 to access to internal OTP:
        ### Setting environment from OTP MAC address = "12:34:56:78:9a:bc"
 
     4 check env update
-       STM32MP> print ethaddr
+       STM32MP> env print ethaddr
        ethaddr=12:34:56:78:9a:bc
 
+warning:: This MAC address provisioning can't be executed twice on the same
+          board as the OTP are protected. It is already done for the board
+          provided by STMicroelectronics.
+
 10. Coprocessor firmware
 ========================
 
diff --git a/board/st/stm32mp1/stm32mp1.c b/board/st/stm32mp1/stm32mp1.c
index ca76579405..c36e7655c0 100644
--- a/board/st/stm32mp1/stm32mp1.c
+++ b/board/st/stm32mp1/stm32mp1.c
@@ -7,6 +7,7 @@
 #include <bootm.h>
 #include <clk.h>
 #include <config.h>
+#include <dfu.h>
 #include <dm.h>
 #include <env.h>
 #include <env_internal.h>
@@ -1011,7 +1012,7 @@ void set_dfu_alt_info(char *interface, char *devstr)
 #include <dfu.h>
 #include <power/stpmic1.h>
 
-int dfu_otp_read(u64 offset, u8 *buffer, long *size)
+static int dfu_otp_read(u64 offset, u8 *buffer, long *size)
 {
 	struct udevice *dev;
 	int ret;
@@ -1031,7 +1032,7 @@ int dfu_otp_read(u64 offset, u8 *buffer, long *size)
 	return 0;
 }
 
-int dfu_pmic_read(u64 offset, u8 *buffer, long *size)
+static int dfu_pmic_read(u64 offset, u8 *buffer, long *size)
 {
 	int ret;
 #ifdef CONFIG_PMIC_STPMIC1
diff --git a/configs/stm32mp15_dhcom_basic_defconfig b/configs/stm32mp15_dhcom_basic_defconfig
new file mode 100644
index 0000000000..921dea242a
--- /dev/null
+++ b/configs/stm32mp15_dhcom_basic_defconfig
@@ -0,0 +1,138 @@
+CONFIG_ARM=y
+CONFIG_ARCH_STM32MP=y
+CONFIG_SYS_MALLOC_F_LEN=0x3000
+CONFIG_ENV_SIZE=0x4000
+CONFIG_SPL_MMC_SUPPORT=y
+CONFIG_SPL=y
+CONFIG_TARGET_DH_STM32MP1_PDK2=y
+CONFIG_SPL_SPI_FLASH_SUPPORT=y
+CONFIG_SPL_SPI_SUPPORT=y
+# CONFIG_ARMV7_VIRT is not set
+CONFIG_SPL_TEXT_BASE=0x2FFC2500
+CONFIG_DISTRO_DEFAULTS=y
+CONFIG_FIT=y
+CONFIG_BOOTCOMMAND="run bootcmd_stm32mp"
+CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION=y
+CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION=3
+CONFIG_SPL_I2C_SUPPORT=y
+CONFIG_SPL_MTD_SUPPORT=y
+CONFIG_SPL_POWER_SUPPORT=y
+CONFIG_SYS_SPI_U_BOOT_OFFS=0x80000
+CONFIG_SYS_PROMPT="STM32MP> "
+# CONFIG_CMD_BOOTD is not set
+# CONFIG_CMD_ELF is not set
+# CONFIG_CMD_IMI is not set
+# CONFIG_CMD_XIMG is not set
+# CONFIG_CMD_EXPORTENV is not set
+CONFIG_CMD_EEPROM=y
+CONFIG_CMD_MEMINFO=y
+CONFIG_CMD_MEMTEST=y
+CONFIG_CMD_ADC=y
+CONFIG_CMD_CLK=y
+CONFIG_CMD_DFU=y
+CONFIG_CMD_FUSE=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_GPT=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_MTD=y
+CONFIG_CMD_REMOTEPROC=y
+CONFIG_CMD_SPI=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_USB_MASS_STORAGE=y
+CONFIG_CMD_BMP=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_TIME=y
+CONFIG_CMD_TIMER=y
+CONFIG_CMD_PMIC=y
+CONFIG_CMD_REGULATOR=y
+CONFIG_CMD_EXT4_WRITE=y
+CONFIG_CMD_MTDPARTS=y
+# CONFIG_SPL_DOS_PARTITION is not set
+CONFIG_DEFAULT_DEVICE_TREE="stm32mp15xx-dhcom-pdk2"
+CONFIG_OF_SPL_REMOVE_PROPS="interrupts interrupt-names interrupts-extended interrupt-controller \\\#interrupt-cells interrupt-parent dmas dma-names assigned-clocks assigned-clock-rates assigned-clock-parents hwlocks"
+CONFIG_ENV_IS_IN_SPI_FLASH=y
+CONFIG_USE_ENV_SPI_BUS=y
+CONFIG_ENV_SPI_BUS=0
+CONFIG_USE_ENV_SPI_CS=y
+CONFIG_ENV_SPI_CS=0
+CONFIG_USE_ENV_SPI_MAX_HZ=y
+CONFIG_ENV_SPI_MAX_HZ=10000000
+CONFIG_USE_ENV_SPI_MODE=y
+CONFIG_ENV_SPI_MODE=0x0
+CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
+CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_IP_DEFRAG=y
+CONFIG_TFTP_BLOCKSIZE=1536
+CONFIG_STM32_ADC=y
+CONFIG_SPL_BLOCK_CACHE=y
+CONFIG_DFU_MMC=y
+CONFIG_DFU_RAM=y
+CONFIG_DFU_VIRT=y
+CONFIG_DM_HWSPINLOCK=y
+CONFIG_HWSPINLOCK_STM32=y
+CONFIG_DM_I2C=y
+CONFIG_SYS_I2C_STM32F7=y
+CONFIG_LED=y
+CONFIG_LED_GPIO=y
+CONFIG_DM_MAILBOX=y
+CONFIG_STM32_IPCC=y
+CONFIG_I2C_EEPROM=y
+CONFIG_DM_MMC=y
+CONFIG_SUPPORT_EMMC_BOOT=y
+CONFIG_STM32_SDMMC2=y
+CONFIG_MTD=y
+CONFIG_DM_SPI_FLASH=y
+CONFIG_SPI_FLASH_MACRONIX=y
+CONFIG_SPI_FLASH_SPANSION=y
+CONFIG_SPI_FLASH_STMICRO=y
+CONFIG_SPI_FLASH_WINBOND=y
+# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
+CONFIG_SPI_FLASH_MTD=y
+CONFIG_SPL_SPI_FLASH_MTD=y
+CONFIG_DM_ETH=y
+CONFIG_DWC_ETH_QOS=y
+CONFIG_PHY=y
+CONFIG_PHY_STM32_USBPHYC=y
+CONFIG_PINCONF=y
+# CONFIG_SPL_PINCTRL_FULL is not set
+CONFIG_PINCTRL_STMFX=y
+CONFIG_DM_PMIC=y
+# CONFIG_SPL_PMIC_CHILDREN is not set
+CONFIG_PMIC_STPMIC1=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_REGULATOR_GPIO=y
+CONFIG_DM_REGULATOR_STM32_VREFBUF=y
+CONFIG_DM_REGULATOR_STPMIC1=y
+CONFIG_REMOTEPROC_STM32_COPRO=y
+CONFIG_DM_RTC=y
+CONFIG_RTC_STM32=y
+CONFIG_SERIAL_RX_BUFFER=y
+CONFIG_SPI=y
+CONFIG_DM_SPI=y
+CONFIG_STM32_QSPI=y
+CONFIG_STM32_SPI=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_DM_USB_GADGET=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_EHCI_GENERIC=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_GADGET_MANUFACTURER="dh"
+CONFIG_USB_GADGET_VENDOR_NUM=0x0483
+CONFIG_USB_GADGET_PRODUCT_NUM=0x5720
+CONFIG_USB_GADGET_DWC2_OTG=y
+CONFIG_USB_GADGET_DOWNLOAD=y
+CONFIG_USB_HOST_ETHER=y
+CONFIG_USB_ETHER_ASIX=y
+CONFIG_DM_VIDEO=y
+CONFIG_BACKLIGHT_GPIO=y
+CONFIG_VIDEO_LCD_ORISETECH_OTM8009A=y
+CONFIG_VIDEO_LCD_RAYDIUM_RM68200=y
+CONFIG_VIDEO_STM32=y
+CONFIG_VIDEO_STM32_DSI=y
+CONFIG_VIDEO_STM32_MAX_XRES=1280
+CONFIG_VIDEO_STM32_MAX_YRES=800
+CONFIG_LZO=y
+CONFIG_FDT_FIXUP_PARTITIONS=y
diff --git a/doc/device-tree-bindings/clock/st,stm32mp1.txt b/doc/device-tree-bindings/clock/st,stm32mp1.txt
index ec1d703f34..a3d427911d 100644
--- a/doc/device-tree-bindings/clock/st,stm32mp1.txt
+++ b/doc/device-tree-bindings/clock/st,stm32mp1.txt
@@ -12,6 +12,9 @@ describes the fields added for clock tree initialization which are not present
 in Linux binding for compatible "st,stm32mp1-rcc" defined in st,stm32mp1-rcc.txt
 file.
 
+This parent node may optionally have additional children nodes which define
+specific init values for RCC elements.
+
 The added properties for clock tree initialization are:
 
 Required properties:
@@ -78,13 +81,16 @@ Required properties:
 	>;
 
 Optional Properties:
-- st,pll : A specific PLL configuration, including frequency.
+- children for a PLL configuration with "st,stm32mp1-pll" compatible
 
-  PLL children nodes for PLL1 to PLL4 (see ref manual for details)
-  are listed with associated index 0 to 3 (st,pll@0 to st,pll@3).
-  PLLx is off when the associated node is absent.
+  each PLL children nodes for PLL1 to PLL4 (see ref manual for details)
+  are listed with associated reg 0 to 3.
+  PLLx is off when the associated node is absent or deactivated.
 
   Here are the available properties for each PLL node:
+    - compatible: should be "st,stm32mp1-pll"
+
+    - reg: index of the pll instance
 
     - cfg: The parameters for PLL configuration in the following order:
            DIVM DIVN DIVP DIVQ DIVR Output.
@@ -118,18 +124,26 @@ Optional Properties:
 
     Example:
 	st,pll@0 {
+		compatible = "st,stm32mp1-pll";
+		reg = <0>;
 		cfg = < 1 53 0 0 0 1 >;
 		frac = < 0x810 >;
 	};
 	st,pll@1 {
+		compatible = "st,stm32mp1-pll";
+		reg = <1>;
 		cfg = < 1 43 1 0 0 PQR(0,1,1) >;
 		csg = < 10 20 1 >;
 	};
 	st,pll@2 {
+		compatible = "st,stm32mp1-pll";
+		reg = <2>;
 		cfg = < 2 85 3 13 3 0 >;
 		csg = < 10 20 SSCG_MODE_CENTER_SPREAD >;
 		};
 	st,pll@3 {
+		compatible = "st,stm32mp1-pll";
+		reg = <3>;
 		cfg = < 2 78 4 7 9 3 >;
 	};
 
@@ -277,6 +291,8 @@ Example of clock tree initialization
 			u-boot,dm-pre-reloc;
 			compatible = "st,stm32mp1-rcc", "syscon";
 			reg = <0x50000000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <0>;
 			#clock-cells = <1>;
 			#reset-cells = <1>;
 			interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
@@ -347,6 +363,8 @@ Example of clock tree initialization
 
 			/* VCO = 1300.0 MHz => P = 650 (CPU) */
 			pll1: st,pll@0 {
+				compatible = "st,stm32mp1-pll";
+				reg = <0>;
 				cfg = < 2 80 0 0 0 PQR(1,0,0) >;
 				frac = < 0x800 >;
 				u-boot,dm-pre-reloc;
@@ -355,6 +373,8 @@ Example of clock tree initialization
 			/* VCO = 1066.0 MHz => P = 266 (AXI), Q = 533 (GPU),
 			                       R = 533 (DDR) */
 			pll2: st,pll@1 {
+				compatible = "st,stm32mp1-pll";
+				reg = <1>;
 				cfg = < 2 65 1 0 0 PQR(1,1,1) >;
 				frac = < 0x1400 >;
 				u-boot,dm-pre-reloc;
@@ -362,6 +382,8 @@ Example of clock tree initialization
 
 			/* VCO = 417.8 MHz => P = 209, Q = 24, R = 11 */
 			pll3: st,pll@2 {
+				compatible = "st,stm32mp1-pll";
+				reg = <2>;
 				cfg = < 1 33 1 16 36 PQR(1,1,1) >;
 				frac = < 0x1a04 >;
 				u-boot,dm-pre-reloc;
@@ -369,6 +391,8 @@ Example of clock tree initialization
 
 			/* VCO = 594.0 MHz => P = 99, Q = 74, R = 74 */
 			pll4: st,pll@3 {
+				compatible = "st,stm32mp1-pll";
+				reg = <3>;
 				cfg = < 3 98 5 7 7 PQR(1,1,1) >;
 				u-boot,dm-pre-reloc;
 			};
diff --git a/doc/device-tree-bindings/mtd/stm32-fmc2-nand.txt b/doc/device-tree-bindings/mtd/stm32-fmc2-nand.txt
index 70e76be2a3..ad2bef8265 100644
--- a/doc/device-tree-bindings/mtd/stm32-fmc2-nand.txt
+++ b/doc/device-tree-bindings/mtd/stm32-fmc2-nand.txt
@@ -18,8 +18,10 @@ Optional properties:
 - dmas: DMA specifiers (see: dma/stm32-mdma.txt)
 - dma-names: Must be "tx", "rx" and "ecc"
 
-Optional children nodes:
-Children nodes represent the available NAND chips.
+* NAND device bindings:
+
+Required properties:
+- reg: describes the CS lines assigned to the NAND device.
 
 Optional properties:
 - nand-on-flash-bbt: see nand.txt
diff --git a/drivers/clk/clk_stm32mp1.c b/drivers/clk/clk_stm32mp1.c
index da66bde41b..fd8c821e48 100644
--- a/drivers/clk/clk_stm32mp1.c
+++ b/drivers/clk/clk_stm32mp1.c
@@ -1218,7 +1218,7 @@ static int stm32mp1_osc_wait(int enable, fdt_addr_t rcc, u32 offset,
 }
 
 static void stm32mp1_lse_enable(fdt_addr_t rcc, int bypass, int digbyp,
-				int lsedrv)
+				u32 lsedrv)
 {
 	u32 value;
 
@@ -1651,8 +1651,8 @@ static int stm32mp1_clktree(struct udevice *dev)
 	unsigned int clkdiv[CLKDIV_NB];
 	unsigned int pllcfg[_PLL_NB][PLLCFG_NB];
 	ofnode plloff[_PLL_NB];
-	int ret;
-	int i, len;
+	int ret, len;
+	uint i;
 	int lse_css = 0;
 	const u32 *pkcs_cell;
 
@@ -1698,7 +1698,8 @@ static int stm32mp1_clktree(struct udevice *dev)
 		stm32mp1_lsi_set(rcc, 1);
 
 	if (priv->osc[_LSE]) {
-		int bypass, digbyp, lsedrv;
+		int bypass, digbyp;
+		u32 lsedrv;
 		struct udevice *dev = priv->osc_dev[_LSE];
 
 		bypass = dev_read_bool(dev, "st,bypass");
diff --git a/drivers/pinctrl/pinctrl-stmfx.c b/drivers/pinctrl/pinctrl-stmfx.c
index c8e61e2918..b0e43ae0a1 100644
--- a/drivers/pinctrl/pinctrl-stmfx.c
+++ b/drivers/pinctrl/pinctrl-stmfx.c
@@ -352,11 +352,12 @@ static int stmfx_chip_init(struct udevice *dev)
 	int ret;
 	struct dm_i2c_chip *chip = dev_get_parent_platdata(dev);
 
-	id = dm_i2c_reg_read(dev, STMFX_REG_CHIP_ID);
-	if (id < 0) {
-		dev_err(dev, "error reading chip id: %d\n", id);
+	ret = dm_i2c_reg_read(dev, STMFX_REG_CHIP_ID);
+	if (ret < 0) {
+		dev_err(dev, "error reading chip id: %d\n", ret);
 		return ret;
 	}
+	id = (u8)ret;
 	/*
 	 * Check that ID is the complement of the I2C address:
 	 * STMFX I2C address follows the 7-bit format (MSB), that's why
diff --git a/include/configs/stih410-b2260.h b/include/configs/stih410-b2260.h
index a8a58f3950..f393aa0264 100644
--- a/include/configs/stih410-b2260.h
+++ b/include/configs/stih410-b2260.h
@@ -19,6 +19,12 @@
 
 /* Environment */
 
+/*
+ * For booting Linux, use the first 256 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ		SZ_256M
+
 #define CONFIG_LOADADDR			CONFIG_SYS_LOAD_ADDR
 #define CONFIG_SYS_BOOTM_LEN		SZ_16M
 
@@ -34,8 +40,6 @@
 			"fdt_addr_r=0x47000000\0"		\
 			"scriptaddr=0x50000000\0"		\
 			"pxefile_addr_r=0x50100000\0"		\
-			"fdt_high=0xffffffffffffffff\0"		\
-			"initrd_high=0xffffffffffffffff\0"	\
 			"ramdisk_addr_r=0x48000000\0"		\
 			BOOTENV
 
diff --git a/include/configs/stm32f429-evaluation.h b/include/configs/stm32f429-evaluation.h
index 7a17222d7b..a7150312ca 100644
--- a/include/configs/stm32f429-evaluation.h
+++ b/include/configs/stm32f429-evaluation.h
@@ -7,6 +7,11 @@
 #ifndef __CONFIG_H
 #define __CONFIG_H
 
+#include <linux/sizes.h>
+
+/* For booting Linux, use the first 16MB of memory */
+#define CONFIG_SYS_BOOTMAPSZ		SZ_16M
+
 #define CONFIG_SYS_FLASH_BASE		0x08000000
 
 #define CONFIG_SYS_INIT_SP_ADDR		0x10010000
@@ -40,12 +45,10 @@
 #define CONFIG_EXTRA_ENV_SETTINGS				\
 			"kernel_addr_r=0x00008000\0"		\
 			"fdtfile=stm32429i-eval.dtb\0"	\
-			"fdt_addr_r=0x00700000\0"		\
-			"scriptaddr=0x00800000\0"		\
-			"pxefile_addr_r=0x00800000\0" \
-			"fdt_high=0xffffffffffffffff\0"		\
-			"initrd_high=0xffffffffffffffff\0"	\
-			"ramdisk_addr_r=0x00900000\0"		\
+			"fdt_addr_r=0x00408000\0"		\
+			"scriptaddr=0x00418000\0"		\
+			"pxefile_addr_r=0x00428000\0" \
+			"ramdisk_addr_r=0x00438000\0"		\
 			BOOTENV
 
 /*
diff --git a/include/configs/stm32f469-discovery.h b/include/configs/stm32f469-discovery.h
index 463f1c4396..8212fb63de 100644
--- a/include/configs/stm32f469-discovery.h
+++ b/include/configs/stm32f469-discovery.h
@@ -7,6 +7,11 @@
 #ifndef __CONFIG_H
 #define __CONFIG_H
 
+#include <linux/sizes.h>
+
+/* For booting Linux, use the first 12MB of memory */
+#define CONFIG_SYS_BOOTMAPSZ		SZ_8M + SZ_4M
+
 #define CONFIG_SYS_FLASH_BASE		0x08000000
 
 #define CONFIG_SYS_INIT_SP_ADDR		0x10010000
@@ -40,12 +45,10 @@
 #define CONFIG_EXTRA_ENV_SETTINGS				\
 			"kernel_addr_r=0x00008000\0"		\
 			"fdtfile=stm32f469-disco.dtb\0"	\
-			"fdt_addr_r=0x00700000\0"		\
-			"scriptaddr=0x00800000\0"		\
-			"pxefile_addr_r=0x00800000\0" \
-			"fdt_high=0xffffffffffffffff\0"		\
-			"initrd_high=0xffffffffffffffff\0"	\
-			"ramdisk_addr_r=0x00900000\0"		\
+			"fdt_addr_r=0x00408000\0"		\
+			"scriptaddr=0x00418000\0"		\
+			"pxefile_addr_r=0x00428000\0" \
+			"ramdisk_addr_r=0x00438000\0"		\
 			BOOTENV
 
 /*
diff --git a/include/configs/stm32f746-disco.h b/include/configs/stm32f746-disco.h
index 337b99977b..45343d2323 100644
--- a/include/configs/stm32f746-disco.h
+++ b/include/configs/stm32f746-disco.h
@@ -7,6 +7,11 @@
 #ifndef __CONFIG_H
 #define __CONFIG_H
 
+#include <linux/sizes.h>
+
+/* For booting Linux, use the first 6MB of memory */
+#define CONFIG_SYS_BOOTMAPSZ		SZ_4M + SZ_2M
+
 #define CONFIG_SYS_FLASH_BASE		0x08000000
 #define CONFIG_SYS_INIT_SP_ADDR		0x20050000
 
@@ -48,12 +53,10 @@
 #define CONFIG_EXTRA_ENV_SETTINGS				\
 			"kernel_addr_r=0xC0008000\0"		\
 			"fdtfile=stm32f746-disco.dtb\0"	\
-			"fdt_addr_r=0xC0500000\0"		\
-			"scriptaddr=0xC0008000\0"		\
-			"pxefile_addr_r=0xC0008000\0" \
-			"fdt_high=0xffffffffffffffff\0"		\
-			"initrd_high=0xffffffffffffffff\0"	\
-			"ramdisk_addr_r=0xC0600000\0"		\
+			"fdt_addr_r=0xC0408000\0"		\
+			"scriptaddr=0xC0418000\0"		\
+			"pxefile_addr_r=0xC0428000\0" \
+			"ramdisk_addr_r=0xC0438000\0"		\
 			BOOTENV
 
 /*
diff --git a/include/configs/stm32h743-disco.h b/include/configs/stm32h743-disco.h
index 74c69eba39..39c93ee6f9 100644
--- a/include/configs/stm32h743-disco.h
+++ b/include/configs/stm32h743-disco.h
@@ -8,6 +8,10 @@
 #define __CONFIG_H
 
 #include <config.h>
+#include <linux/sizes.h>
+
+/* For booting Linux, use the first 16MB of memory */
+#define CONFIG_SYS_BOOTMAPSZ		SZ_16M
 
 #define CONFIG_SYS_FLASH_BASE		0x08000000
 #define CONFIG_SYS_INIT_SP_ADDR		0x24040000
@@ -35,12 +39,10 @@
 #define CONFIG_EXTRA_ENV_SETTINGS				\
 			"kernel_addr_r=0xD0008000\0"		\
 			"fdtfile=stm32h743i-disco.dtb\0"	\
-			"fdt_addr_r=0xD0700000\0"		\
-			"scriptaddr=0xD0800000\0"		\
-			"pxefile_addr_r=0xD0800000\0" \
-			"fdt_high=0xffffffffffffffff\0"		\
-			"initrd_high=0xffffffffffffffff\0"	\
-			"ramdisk_addr_r=0xD0900000\0"		\
+			"fdt_addr_r=0xD0408000\0"		\
+			"scriptaddr=0xD0418000\0"		\
+			"pxefile_addr_r=0xD0428000\0" \
+			"ramdisk_addr_r=0xD0438000\0"		\
 			BOOTENV
 
 /*
diff --git a/include/configs/stm32h743-eval.h b/include/configs/stm32h743-eval.h
index b7c84922ab..8eb94c1ad4 100644
--- a/include/configs/stm32h743-eval.h
+++ b/include/configs/stm32h743-eval.h
@@ -8,6 +8,10 @@
 #define __CONFIG_H
 
 #include <config.h>
+#include <linux/sizes.h>
+
+/* For booting Linux, use the first 16MB of memory */
+#define CONFIG_SYS_BOOTMAPSZ		SZ_16M
 
 #define CONFIG_SYS_FLASH_BASE		0x08000000
 #define CONFIG_SYS_INIT_SP_ADDR		0x24040000
@@ -35,12 +39,10 @@
 #define CONFIG_EXTRA_ENV_SETTINGS				\
 			"kernel_addr_r=0xD0008000\0"		\
 			"fdtfile=stm32h743i-eval.dtb\0"	\
-			"fdt_addr_r=0xD0700000\0"		\
-			"scriptaddr=0xD0800000\0"		\
-			"pxefile_addr_r=0xD0800000\0" \
-			"fdt_high=0xffffffffffffffff\0"		\
-			"initrd_high=0xffffffffffffffff\0"	\
-			"ramdisk_addr_r=0xD0900000\0"		\
+			"fdt_addr_r=0xD0408000\0"		\
+			"scriptaddr=0xD0418000\0"		\
+			"pxefile_addr_r=0xD0428000\0" \
+			"ramdisk_addr_r=0xD0438000\0"		\
 			BOOTENV
 
 /*
diff --git a/include/configs/stm32mp1.h b/include/configs/stm32mp1.h
index a66534e027..42717c167e 100644
--- a/include/configs/stm32mp1.h
+++ b/include/configs/stm32mp1.h
@@ -43,8 +43,14 @@
 #define CONFIG_SETUP_MEMORY_TAGS
 #define CONFIG_INITRD_TAG
 
+/*
+ * For booting Linux, use the first 256 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ		SZ_256M
+
 /* Extend size of kernel image for uncompression */
-#define CONFIG_SYS_BOOTM_LEN			SZ_32M
+#define CONFIG_SYS_BOOTM_LEN		SZ_32M
 
 /* SPL support */
 #ifdef CONFIG_SPL
@@ -215,8 +221,6 @@
 	"pxefile_addr_r=0xc4200000\0" \
 	"splashimage=0xc4300000\0"  \
 	"ramdisk_addr_r=0xc4400000\0" \
-	"fdt_high=0xffffffff\0" \
-	"initrd_high=0xffffffff\0" \
 	"altbootcmd=run bootcmd\0" \
 	"env_default=1\0" \
 	"env_check=if test $env_default -eq 1;"\
diff --git a/tools/stm32image.c b/tools/stm32image.c
index ff3ec5f3f2..18357c0518 100644
--- a/tools/stm32image.c
+++ b/tools/stm32image.c
@@ -45,7 +45,7 @@ static void stm32image_default_header(struct stm32_header *ptr)
 	ptr->magic_number = HEADER_MAGIC;
 	ptr->header_version[VER_MAJOR_IDX] = HEADER_VERSION_V1;
 	ptr->option_flags = HEADER_DEFAULT_OPTION;
-	ptr->ecdsa_algorithm = 1;
+	ptr->ecdsa_algorithm = cpu_to_le32(1);
 	ptr->binary_type = HEADER_TYPE_UBOOT;
 }
 
@@ -131,7 +131,8 @@ static void stm32image_set_header(void *ptr, struct stat *sbuf, int ifd,
 	stm32hdr->image_entry_point = cpu_to_le32(params->ep);
 	stm32hdr->image_length = cpu_to_le32((uint32_t)sbuf->st_size -
 					     sizeof(struct stm32_header));
-	stm32hdr->image_checksum = stm32image_checksum(ptr, sbuf->st_size);
+	stm32hdr->image_checksum =
+		cpu_to_le32(stm32image_checksum(ptr, sbuf->st_size));
 }
 
 /*