summaryrefslogtreecommitdiff
path: root/README
diff options
context:
space:
mode:
authorSimon Glass <sjg@chromium.org>2017-07-23 21:19:40 -0600
committerTom Rini <trini@konsulko.com>2017-07-25 21:08:07 -0400
commite73496d08e2dc60f3e00554c71b92f72cdebf0fd (patch)
tree1ff064e00f57e6f7a38aff40dce30b2b0d8289bf /README
parent2be296538e2e9d2893dc495b3fc8f9f6acb1454c (diff)
env: Move help from README to Kconfig
The CONFIG_ENV_IS_IN_... options which have already been converted to Kconfig only have a small amount of help. Move the rest of it over from the README. Signed-off-by: Simon Glass <sjg@chromium.org>
Diffstat (limited to 'README')
-rw-r--r--README114
1 files changed, 0 insertions, 114 deletions
diff --git a/README b/README
index 8abaf6473f..f09e0db2fb 100644
--- a/README
+++ b/README
@@ -3634,75 +3634,12 @@ BE CAREFUL! For some special cases, the local device can not use
environment stored in a remote NOR flash by SRIO or PCIE link,
but it can not erase, write this NOR flash by SRIO or PCIE interface.
-- CONFIG_ENV_IS_IN_NAND:
-
- Define this if you have a NAND device which you want to use
- for the environment.
-
- - CONFIG_ENV_OFFSET:
- - CONFIG_ENV_SIZE:
-
- These two #defines specify the offset and size of the environment
- area within the first NAND device. CONFIG_ENV_OFFSET must be
- aligned to an erase block boundary.
-
- - CONFIG_ENV_OFFSET_REDUND (optional):
-
- This setting describes a second storage area of CONFIG_ENV_SIZE
- size used to hold a redundant copy of the environment data, so
- that there is a valid backup copy in case there is a power failure
- during a "saveenv" operation. CONFIG_ENV_OFFSET_REDUND must be
- aligned to an erase block boundary.
-
- - CONFIG_ENV_RANGE (optional):
-
- Specifies the length of the region in which the environment
- can be written. This should be a multiple of the NAND device's
- block size. Specifying a range with more erase blocks than
- are needed to hold CONFIG_ENV_SIZE allows bad blocks within
- the range to be avoided.
-
- - CONFIG_ENV_OFFSET_OOB (optional):
-
- Enables support for dynamically retrieving the offset of the
- environment from block zero's out-of-band data. The
- "nand env.oob" command can be used to record this offset.
- Currently, CONFIG_ENV_OFFSET_REDUND is not supported when
- using CONFIG_ENV_OFFSET_OOB.
-
- CONFIG_NAND_ENV_DST
Defines address in RAM to which the nand_spl code should copy the
environment. If redundant environment is used, it will be copied to
CONFIG_NAND_ENV_DST + CONFIG_ENV_SIZE.
-- CONFIG_ENV_IS_IN_UBI:
-
- Define this if you have an UBI volume that you want to use for the
- environment. This has the benefit of wear-leveling the environment
- accesses, which is important on NAND.
-
- - CONFIG_ENV_UBI_PART:
-
- Define this to a string that is the mtd partition containing the UBI.
-
- - CONFIG_ENV_UBI_VOLUME:
-
- Define this to the name of the volume that you want to store the
- environment in.
-
- - CONFIG_ENV_UBI_VOLUME_REDUND:
-
- Define this to the name of another volume to store a second copy of
- the environment in. This will enable redundant environments in UBI.
- It is assumed that both volumes are in the same MTD partition.
-
- - CONFIG_UBI_SILENCE_MSG
- - CONFIG_UBIFS_SILENCE_MSG
-
- You will probably want to define these to avoid a really noisy system
- when storing the env in UBI.
-
- CONFIG_ENV_IS_IN_FAT:
Define this if you want to use the FAT file system for the environment.
@@ -3734,57 +3671,6 @@ but it can not erase, write this NOR flash by SRIO or PCIE interface.
- CONFIG_FAT_WRITE:
This must be enabled. Otherwise it cannot save the environment file.
-- CONFIG_ENV_IS_IN_MMC:
-
- Define this if you have an MMC device which you want to use for the
- environment.
-
- - CONFIG_SYS_MMC_ENV_DEV:
-
- Specifies which MMC device the environment is stored in.
-
- - CONFIG_SYS_MMC_ENV_PART (optional):
-
- Specifies which MMC partition the environment is stored in. If not
- set, defaults to partition 0, the user area. Common values might be
- 1 (first MMC boot partition), 2 (second MMC boot partition).
-
- - CONFIG_ENV_OFFSET:
- - CONFIG_ENV_SIZE:
-
- These two #defines specify the offset and size of the environment
- area within the specified MMC device.
-
- If offset is positive (the usual case), it is treated as relative to
- the start of the MMC partition. If offset is negative, it is treated
- as relative to the end of the MMC partition. This can be useful if
- your board may be fitted with different MMC devices, which have
- different sizes for the MMC partitions, and you always want the
- environment placed at the very end of the partition, to leave the
- maximum possible space before it, to store other data.
-
- These two values are in units of bytes, but must be aligned to an
- MMC sector boundary.
-
- - CONFIG_ENV_OFFSET_REDUND (optional):
-
- Specifies a second storage area, of CONFIG_ENV_SIZE size, used to
- hold a redundant copy of the environment data. This provides a
- valid backup copy in case the other copy is corrupted, e.g. due
- to a power failure during a "saveenv" operation.
-
- This value may also be positive or negative; this is handled in the
- same way as CONFIG_ENV_OFFSET.
-
- This value is also in units of bytes, but must also be aligned to
- an MMC sector boundary.
-
- - CONFIG_ENV_SIZE_REDUND (optional):
-
- This value need not be set, even when CONFIG_ENV_OFFSET_REDUND is
- set. If this value is set, it must be set to the same value as
- CONFIG_ENV_SIZE.
-
Please note that the environment is read-only until the monitor
has been relocated to RAM and a RAM copy of the environment has been
created; also, when using EEPROM you will have to use getenv_f()