ARM: dts: at91: Add dts files for at91sam9x5ek

The device tree source files of at91sam9x5ek board are copied from
the Linux v4.10, do the changes below.
 - Add the reg property for the pinctrl node.
 - Move the gpio (pioA, pioB, pioC ...) nodes as the pinctrl's
   slibling nodes, instead of the child nodes.
 - Add the "u-boot,dm-pre-reloc" property to determine which nodes
   are used by the board_init_f stage.
 - Change the compatible of the spi flash to "spi-flash".
 - Add the spi0 aliases.
 - Fix the compilation warnings.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

1 files changed, 69 insertions, 0 deletions

diff --git a/arch/arm/dts/at91sam9g25ek.dts b/arch/arm/dts/at91sam9g25ek.dts
new file mode 100644
index 0000000000..91a7177447
--- /dev/null
+++ b/arch/arm/dts/at91sam9g25ek.dts
@@ -0,0 +1,69 @@
+/*
+ * at91sam9g25ek.dts - Device Tree file for AT91SAM9G25-EK board
+ *
+ *  Copyright (C) 2012 Atmel,
+ *                2012 Nicolas Ferre <nicolas.ferre@atmel.com>
+ *
+ * Licensed under GPLv2 or later.
+ */
+/dts-v1/;
+#include "at91sam9g25.dtsi"
+#include "at91sam9x5ek.dtsi"
+
+/ {
+	model = "Atmel AT91SAM9G25-EK";
+	compatible = "atmel,at91sam9g25ek", "atmel,at91sam9x5ek", "atmel,at91sam9x5", "atmel,at91sam9";
+
+	ahb {
+		apb {
+			spi0: spi@f0000000 {
+				status = "disabled";
+			};
+
+			mmc1: mmc@f000c000 {
+				status = "disabled";
+			};
+
+			i2c0: i2c@f8010000 {
+				ov2640: camera@0x30 {
+					compatible = "ovti,ov2640";
+					reg = <0x30>;
+					pinctrl-names = "default";
+					pinctrl-0 = <&pinctrl_pck0_as_isi_mck &pinctrl_sensor_power &pinctrl_sensor_reset>;
+					resetb-gpios = <&pioA 7 GPIO_ACTIVE_LOW>;
+					pwdn-gpios = <&pioA 13 GPIO_ACTIVE_HIGH>;
+					clocks = <&pck0>;
+					clock-names = "xvclk";
+					assigned-clocks = <&pck0>;
+					assigned-clock-rates = <25000000>;
+					status = "okay";
+
+					port {
+						ov2640_0: endpoint {
+							remote-endpoint = <&isi_0>;
+							bus-width = <8>;
+						};
+					};
+				};
+			};
+
+			macb0: ethernet@f802c000 {
+				phy-mode = "rmii";
+				status = "okay";
+			};
+
+			isi: isi@f8048000 {
+				status = "okay";
+				port {
+					isi_0: endpoint@0 {
+						reg = <0>;
+						remote-endpoint = <&ov2640_0>;
+						bus-width = <8>;
+						vsync-active = <1>;
+						hsync-active = <1>;
+					};
+				};
+			};
+		};
+	};
+};