fdt: update bcm283x device tree sources to Linux 5.1-rc6 state

Updating the bcm283x device tree sources adds the device trees for

- Raspberry Pi 3 Model A+
- Raspberry Pi 3 Model B+
- Raspberry Pi Compute Module IO board rev1
- Raspberry Pi Compute Module 3 IO board V3.0
- Raspberry Pi Zero

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>

1 files changed, 125 insertions, 3 deletions

diff --git a/arch/arm/dts/bcm2837-rpi-3-b.dts b/arch/arm/dts/bcm2837-rpi-3-b.dts
index 20725ca487..ce71f578c5 100644
--- a/arch/arm/dts/bcm2837-rpi-3-b.dts
+++ b/arch/arm/dts/bcm2837-rpi-3-b.dts
@@ -1,6 +1,7 @@
+// SPDX-License-Identifier: GPL-2.0
 /dts-v1/;
 #include "bcm2837.dtsi"
-#include "bcm2835-rpi.dtsi"
+#include "bcm2836-rpi.dtsi"
 #include "bcm283x-rpi-smsc9514.dtsi"
 #include "bcm283x-rpi-usb-host.dtsi"
 
@@ -8,15 +9,122 @@
 	compatible = "raspberrypi,3-model-b", "brcm,bcm2837";
 	model = "Raspberry Pi 3 Model B";
 
-	memory {
+	chosen {
+		/* 8250 auxiliary UART instead of pl011 */
+		stdout-path = "serial1:115200n8";
+	};
+
+	memory@0 {
 		reg = <0 0x40000000>;
 	};
 
 	leds {
 		act {
-			gpios = <&gpio 47 0>;
+			gpios = <&expgpio 2 GPIO_ACTIVE_HIGH>;
 		};
 	};
+
+	wifi_pwrseq: wifi-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&firmware {
+	expgpio: gpio {
+		compatible = "raspberrypi,firmware-gpio";
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names = "BT_ON",
+				  "WL_ON",
+				  "STATUS_LED",
+				  "LAN_RUN",
+				  "HDMI_HPD_N",
+				  "CAM_GPIO0",
+				  "CAM_GPIO1",
+				  "PWR_LOW_N";
+		status = "okay";
+	};
+};
+
+&gpio {
+	/*
+	 * Taken from rpi_SCH_3b_1p2_reduced.pdf and
+	 * the official GPU firmware DT blob.
+	 *
+	 * Legend:
+	 * "NC" = not connected (no rail from the SoC)
+	 * "FOO" = GPIO line named "FOO" on the schematic
+	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
+	 */
+	gpio-line-names = "ID_SDA",
+			  "ID_SCL",
+			  "SDA1",
+			  "SCL1",
+			  "GPIO_GCLK",
+			  "GPIO5",
+			  "GPIO6",
+			  "SPI_CE1_N",
+			  "SPI_CE0_N",
+			  "SPI_MISO",
+			  "SPI_MOSI",
+			  "SPI_SCLK",
+			  "GPIO12",
+			  "GPIO13",
+			  /* Serial port */
+			  "TXD1",
+			  "RXD1",
+			  "GPIO16",
+			  "GPIO17",
+			  "GPIO18",
+			  "GPIO19",
+			  "GPIO20",
+			  "GPIO21",
+			  "GPIO22",
+			  "GPIO23",
+			  "GPIO24",
+			  "GPIO25",
+			  "GPIO26",
+			  "GPIO27",
+			  "", /* GPIO 28 */
+			  "LAN_RUN_BOOT",
+			  /* Used by BT module */
+			  "CTS0",
+			  "RTS0",
+			  "TXD0",
+			  "RXD0",
+			  /* Used by Wifi */
+			  "SD1_CLK",
+			  "SD1_CMD",
+			  "SD1_DATA0",
+			  "SD1_DATA1",
+			  "SD1_DATA2",
+			  "SD1_DATA3",
+			  "PWM0_OUT",
+			  "PWM1_OUT",
+			  "ETHCLK",
+			  "WIFI_CLK",
+			  "SDA0",
+			  "SCL0",
+			  "SMPS_SCL",
+			  "SMPS_SDA",
+			  /* Used by SD Card */
+			  "SD_CLK_R",
+			  "SD_CMD_R",
+			  "SD_DATA0_R",
+			  "SD_DATA1_R",
+			  "SD_DATA2_R",
+			  "SD_DATA3_R";
+};
+
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio41>;
+	status = "okay";
+};
+
+&hdmi {
+	hpd-gpios = <&expgpio 4 GPIO_ACTIVE_LOW>;
 };
 
 /* uart0 communicates with the BT module */
@@ -24,6 +132,12 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_gpio32 &gpclk2_gpio43>;
 	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		max-speed = <2000000>;
+		shutdown-gpios = <&expgpio 0 GPIO_ACTIVE_HIGH>;
+	};
 };
 
 /* uart1 is mapped to the pin header */
@@ -35,11 +149,19 @@
 
 /* SDHCI is used to control the SDIO for wireless */
 &sdhci {
+	#address-cells = <1>;
+	#size-cells = <0>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&emmc_gpio34>;
 	status = "okay";
 	bus-width = <4>;
 	non-removable;
+	mmc-pwrseq = <&wifi_pwrseq>;
+
+	brcmf: wifi@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+	};
 };
 
 /* SDHOST is used to drive the SD card */