ARM: dts: Sync Amlogic G12A with Linux 5.3-rc1

Sync the Amlogic Meson G12A DT and Bindings file with the Linux 5.3-rc1
from the commit 5f9e832c1370 ("Linus 5.3-rc1").

Also remove the meson-g12a-u-boot.dtsi and meson-g12a-u200-u-boot.dtsi,
now conflicting with the main DT content.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Mark Kettenis <kettenis@openbsd.org>

1 files changed, 100 insertions, 22 deletions

diff --git a/arch/arm/dts/meson-g12a-u200.dts b/arch/arm/dts/meson-g12a-u200.dts
index 0e8045b8a9..8551fbd4a4 100644
--- a/arch/arm/dts/meson-g12a-u200.dts
+++ b/arch/arm/dts/meson-g12a-u200.dts
@@ -15,14 +15,12 @@
 
 	aliases {
 		serial0 = &uart_AO;
+		ethernet0 = &ethmac;
 	};
+
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
-	memory@0 {
-		device_type = "memory";
-		reg = <0x0 0x0 0x0 0x40000000>;
-	};
 
 	cvbs-connector {
 		compatible = "composite-video-connector";
@@ -34,13 +32,9 @@
 		};
 	};
 
-	flash_1v8: regulator-flash_1v8 {
-		compatible = "regulator-fixed";
-		regulator-name = "FLASH_1V8";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-		vin-supply = <&vcc_3v3>;
-		regulator-always-on;
+	emmc_pwrseq: emmc-pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>;
 	};
 
 	hdmi-connector {
@@ -54,6 +48,20 @@
 		};
 	};
 
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x40000000>;
+	};
+
+	flash_1v8: regulator-flash_1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "FLASH_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc_3v3>;
+		regulator-always-on;
+	};
+
 	main_12v: regulator-main_12v {
 		compatible = "regulator-fixed";
 		regulator-name = "12V";
@@ -62,6 +70,17 @@
 		regulator-always-on;
 	};
 
+	usb_pwr_en: regulator-usb_pwr_en {
+		compatible = "regulator-fixed";
+		regulator-name = "USB_PWR_EN";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc_5v>;
+
+		gpio = <&gpio GPIOH_6 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
 	vcc_1v8: regulator-vcc_1v8 {
 		compatible = "regulator-fixed";
 		regulator-name = "VCC_1V8";
@@ -92,17 +111,6 @@
 		enable-active-high;
 	};
 
-	usb_pwr_en: regulator-usb_pwr_en {
-		compatible = "regulator-fixed";
-		regulator-name = "USB_PWR_EN";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		vin-supply = <&vcc_5v>;
-
-		gpio = <&gpio GPIOH_6 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-	};
-
 	vddao_1v8: regulator-vddao_1v8 {
 		compatible = "regulator-fixed";
 		regulator-name = "VDDAO_1V8";
@@ -143,6 +151,12 @@
 	};
 };
 
+&ethmac {
+	status = "okay";
+	phy-handle = <&internal_ephy>;
+	phy-mode = "rmii";
+};
+
 &hdmi_tx {
 	status = "okay";
 	pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>;
@@ -156,6 +170,70 @@
 	};
 };
 
+&ir {
+	status = "okay";
+	pinctrl-0 = <&remote_input_ao_pins>;
+	pinctrl-names = "default";
+};
+
+/* i2c Touch */
+&i2c0 {
+	status = "okay";
+	pinctrl-0 = <&i2c0_sda_z0_pins>, <&i2c0_sck_z1_pins>;
+	pinctrl-names = "default";
+};
+
+/* i2c CM */
+&i2c2 {
+	status = "okay";
+	pinctrl-0 = <&i2c2_sda_z_pins>, <&i2c2_sck_z_pins>;
+	pinctrl-names = "default";
+};
+
+/* i2c Audio */
+&i2c3 {
+	status = "okay";
+	pinctrl-0 = <&i2c3_sda_a_pins>, <&i2c3_sck_a_pins>;
+	pinctrl-names = "default";
+};
+
+/* SD card */
+&sd_emmc_b {
+	status = "okay";
+	pinctrl-0 = <&sdcard_c_pins>;
+	pinctrl-1 = <&sdcard_clk_gate_c_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	max-frequency = <50000000>;
+	disable-wp;
+
+	cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>;
+	vmmc-supply = <&vddao_3v3>;
+	vqmmc-supply = <&vddao_3v3>;
+};
+
+/* eMMC */
+&sd_emmc_c {
+	status = "okay";
+	pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
+	pinctrl-1 = <&emmc_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+	max-frequency = <200000000>;
+	non-removable;
+	disable-wp;
+
+	mmc-pwrseq = <&emmc_pwrseq>;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&flash_1v8>;
+};
+
 &uart_AO {
 	status = "okay";
 	pinctrl-0 = <&uart_ao_a_pins>;