ARM: at91: dt: add dts files for sama5d3xek board

Add the device tree files for sama5d3xek board.

The dts files are copied from Linux-4.9, do the changes as below.
 - add reg property for the pinctrl node.
 - move the gpio nodes (pioA, pioB, pioC ...) as the pinctrl's
   slibling nodes.
 - add the "u-boot,dm-pre-reloc" property to determine which nodes
   which are needed by SPL and by the board_init_f stage.
 - fix the compile warning.
 - add spi0 node aliases.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>

1 files changed, 236 insertions, 0 deletions

diff --git a/arch/arm/dts/sama5d3xmb_cmp.dtsi b/arch/arm/dts/sama5d3xmb_cmp.dtsi
new file mode 100644
index 0000000000..77f989ce3c
--- /dev/null
+++ b/arch/arm/dts/sama5d3xmb_cmp.dtsi
@@ -0,0 +1,236 @@
+/*
+ * sama5d3xmb_cmp.dts - Device Tree file for SAMA5D3x CMP mother board
+ *
+ *  Copyright (C) 2016 Atmel,
+ *
+ * Licensed under GPLv2 or later.
+ */
+#include "sama5d3xcm_cmp.dtsi"
+
+/ {
+	compatible = "atmel,sama5d3xmb", "atmel,sama5d3xcm", "atmel,sama5d3", "atmel,sama5";
+
+	chosen {
+		u-boot,dm-pre-reloc;
+		stdout-path = &dbgu;
+	};
+
+	ahb {
+		apb {
+			mmc0: mmc@f0000000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_mmc0_clk_cmd_dat0 &pinctrl_mmc0_dat1_3 &pinctrl_mmc0_cd>;
+				status = "okay";
+				slot@0 {
+					reg = <0>;
+					bus-width = <4>;
+					cd-gpios = <&pioD 17 GPIO_ACTIVE_HIGH>;
+				};
+			};
+
+			spi0: spi@f0004000 {
+				dmas = <0>, <0>;	/*  Do not use DMA for spi0 */
+
+				spi_flash@0 {
+					compatible = "spi-flash";
+					spi-max-frequency = <50000000>;
+					reg = <0>;
+				};
+			};
+
+			ssc0: ssc@f0008000 {
+				atmel,clk-from-rk-pin;
+			};
+
+			/*
+			 * i2c0 conflicts with ISI:
+			 * disable it to allow the use of ISI
+			 * can not enable audio when i2c0 disabled
+			 */
+			i2c0: i2c@f0014000 {
+				wm8904: wm8904@1a {
+					compatible = "wlf,wm8904";
+					reg = <0x1a>;
+					clocks = <&pck0>;
+					clock-names = "mclk";
+				};
+			};
+
+			i2c1: i2c@f0018000 {
+				ov2640: camera@0x30 {
+					compatible = "ovti,ov2640";
+					reg = <0x30>;
+					pinctrl-names = "default";
+					pinctrl-0 = <&pinctrl_pck1_as_isi_mck &pinctrl_sensor_power &pinctrl_sensor_reset>;
+					resetb-gpios = <&pioE 24 GPIO_ACTIVE_LOW>;
+					pwdn-gpios = <&pioE 29 GPIO_ACTIVE_HIGH>;
+					/* use pck1 for the master clock of ov2640 */
+					clocks = <&pck1>;
+					clock-names = "xvclk";
+					assigned-clocks = <&pck1>;
+					assigned-clock-rates = <25000000>;
+
+					port {
+						ov2640_0: endpoint {
+							remote-endpoint = <&isi_0>;
+							bus-width = <8>;
+						};
+					};
+				};
+			};
+
+			usart1: serial@f0020000 {
+				dmas = <0>, <0>;	/*  Do not use DMA for usart1 */
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_usart1 &pinctrl_usart1_rts_cts>;
+				status = "okay";
+			};
+
+			isi: isi@f0034000 {
+				port {
+					isi_0: endpoint {
+						remote-endpoint = <&ov2640_0>;
+						bus-width = <8>;
+						vsync-active = <1>;
+						hsync-active = <1>;
+					};
+				};
+			};
+
+			mmc1: mmc@f8000000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_mmc1_clk_cmd_dat0 &pinctrl_mmc1_dat1_3 &pinctrl_mmc1_cd>;
+				status = "okay";
+				slot@0 {
+					reg = <0>;
+					bus-width = <4>;
+					cd-gpios = <&pioD 18 GPIO_ACTIVE_HIGH>;
+				};
+			};
+
+			adc0: adc@f8018000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <
+					&pinctrl_adc0_adtrg
+					&pinctrl_adc0_ad0
+					&pinctrl_adc0_ad1
+					&pinctrl_adc0_ad2
+					&pinctrl_adc0_ad3
+					&pinctrl_adc0_ad4
+					>;
+				status = "okay";
+			};
+
+			macb1: ethernet@f802c000 {
+				phy-mode = "rmii";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+				phy0: ethernet-phy@1 {
+					/*interrupt-parent = <&pioE>;*/
+					/*interrupts = <30 IRQ_TYPE_EDGE_FALLING>;*/
+					reg = <1>;
+				};
+			};
+
+			pinctrl@fffff200 {
+				board {
+					pinctrl_gpio_keys: gpio_keys {
+						atmel,pins =
+							<AT91_PIOE 27 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP>;
+					};
+
+					pinctrl_mmc0_cd: mmc0_cd {
+						atmel,pins =
+							<AT91_PIOD 17 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PD17 GPIO with pullup deglitch */
+					};
+
+					pinctrl_mmc1_cd: mmc1_cd {
+						atmel,pins =
+							<AT91_PIOD 18 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PD18 GPIO with pullup deglitch */
+					};
+
+					pinctrl_pck0_as_audio_mck: pck0_as_audio_mck {
+						atmel,pins =
+							<AT91_PIOD 30 AT91_PERIPH_B AT91_PINCTRL_NONE>;	/* PD30 periph B */
+					};
+
+					pinctrl_pck1_as_isi_mck: pck1_as_isi_mck-0 {
+						atmel,pins =
+							<AT91_PIOD 31 AT91_PERIPH_B AT91_PINCTRL_NONE>;	/* PD31 periph B ISI_MCK */
+					};
+
+					pinctrl_sensor_reset: sensor_reset-0 {
+						atmel,pins =
+							<AT91_PIOE 24 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;   /* PE24 gpio */
+					};
+
+					pinctrl_sensor_power: sensor_power-0 {
+						atmel,pins =
+							<AT91_PIOE 29 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>; /* PE29 gpio */
+					};
+
+					pinctrl_usba_vbus: usba_vbus {
+						atmel,pins =
+							<AT91_PIOD 29 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>; /* PD29 GPIO with deglitch */
+					};
+				};
+			};
+
+			dbgu: serial@ffffee00 {
+				dmas = <0>, <0>;	/*  Do not use DMA for dbgu */
+				status = "okay";
+				u-boot,dm-pre-reloc;
+			};
+
+			watchdog@fffffe40 {
+				status = "okay";
+			};
+		};
+
+		usb0: gadget@00500000 {
+			atmel,vbus-gpio = <&pioD 29 GPIO_ACTIVE_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_usba_vbus>;
+			status = "okay";
+		};
+	};
+
+	sound {
+		compatible = "atmel,asoc-wm8904";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pck0_as_audio_mck>;
+
+		atmel,model = "wm8904 @ SAMA5D3EK";
+		atmel,audio-routing =
+			"Headphone Jack", "HPOUTL",
+			"Headphone Jack", "HPOUTR",
+			"IN2L", "Line In Jack",
+			"IN2R", "Line In Jack",
+			"Mic", "MICBIAS",
+			"IN1L", "Mic";
+
+		atmel,ssc-controller = <&ssc0>;
+		atmel,audio-codec = <&wm8904>;
+
+		status = "disabled";
+	};
+
+	/* Conflict with LCD pins */
+	gpio_keys {
+		compatible = "gpio-keys";
+		status = "okay";
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_keys>;
+
+		pb_user1 {
+			label = "pb_user1";
+			gpios = <&pioE 27 GPIO_ACTIVE_HIGH>;
+			linux,code = <0x100>;
+			gpio-key,wakeup;
+		};
+	};
+};