sunxi: A64: Update .dts/.dtsi files

Update the .dts/.dtsi file from the Linux sunxi/dt64-for-4.20 tree:
commit 679294497be31596e1c9c61507746d72b6b05f26
Author: Rodrigo Exterckötter Tjäder <rodrigo@tjader.xyz>
Date:   Wed Sep 26 19:48:24 2018 +0000
    arm64: dts: allwinner: a64: a64-olinuxino: set the PHY TX delay

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>

1 files changed, 100 insertions, 3 deletions

diff --git a/arch/arm/dts/sun50i-a64-olinuxino.dts b/arch/arm/dts/sun50i-a64-olinuxino.dts
index 3b3081b10e..f7a4bccaa5 100644
--- a/arch/arm/dts/sun50i-a64-olinuxino.dts
+++ b/arch/arm/dts/sun50i-a64-olinuxino.dts
@@ -51,6 +51,7 @@
 	compatible = "olimex,a64-olinuxino", "allwinner,sun50i-a64";
 
 	aliases {
+		ethernet0 = &emac;
 		serial0 = &uart0;
 	};
 
@@ -58,12 +59,74 @@
 		stdout-path = "serial0:115200n8";
 	};
 
+	hdmi-connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+
+	reg_usb1_vbus: usb1-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb1-vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-boot-on;
+		enable-active-high;
+		gpio = <&pio 6 9 GPIO_ACTIVE_HIGH>; /* PG9 */
+		status = "okay";
+	};
+
 	wifi_pwrseq: wifi_pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
 	};
 };
 
+&de {
+	status = "okay";
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&emac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&rgmii_pins>;
+	phy-mode = "rgmii";
+	phy-handle = <&ext_rgmii_phy>;
+	phy-supply = <&reg_dcdc1>;
+	allwinner,tx-delay-ps = <600>;
+	status = "okay";
+};
+
+&hdmi {
+	hvcc-supply = <&reg_dldo1>;
+	status = "okay";
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
+&mdio {
+	ext_rgmii_phy: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+	};
+};
+
 &mmc0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc0_pins>;
@@ -92,6 +155,14 @@
 	};
 };
 
+&ohci0 {
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
 &r_rsb {
 	status = "okay";
 
@@ -100,6 +171,7 @@
 		reg = <0x3a3>;
 		interrupt-parent = <&r_intc>;
 		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+		x-powers,drive-vbus-en;	/* set N_VBUSEN as output pin */
 	};
 };
 
@@ -142,10 +214,14 @@
 
 /* DCDC3 is polyphased with DCDC2 */
 
+/*
+ * The board uses DDR3L DRAM chips. 1.36V is the closest to the nominal
+ * 1.35V that the PMIC can drive.
+ */
 &reg_dcdc5 {
 	regulator-always-on;
-	regulator-min-microvolt = <1500000>;
-	regulator-max-microvolt = <1500000>;
+	regulator-min-microvolt = <1360000>;
+	regulator-max-microvolt = <1360000>;
 	regulator-name = "vcc-ddr3";
 };
 
@@ -180,6 +256,11 @@
 	regulator-name = "vcc-wifi-io";
 };
 
+&reg_drivevbus {
+	regulator-name = "usb0-vbus";
+	status = "okay";
+};
+
 &reg_eldo1 {
 	regulator-min-microvolt = <1800000>;
 	regulator-max-microvolt = <1800000>;
@@ -214,8 +295,24 @@
 	regulator-name = "vcc-rtc";
 };
 
+&simplefb_hdmi {
+	vcc-hdmi-supply = <&reg_dldo1>;
+};
+
 &uart0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&uart0_pins_a>;
+	pinctrl-0 = <&uart0_pb_pins>;
+	status = "okay";
+};
+
+&usb_otg {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usbphy {
 	status = "okay";
+	usb0_id_det-gpios = <&pio 7 9 GPIO_ACTIVE_HIGH>; /* PH9 */
+	usb0_vbus-supply = <&reg_drivevbus>;
+	usb1_vbus-supply = <&reg_usb1_vbus>;
 };