ARM: dts: sun7i: Update A20 dts(i) files from Linux-v4.18-rc3

Update all A10 devicetree dtsi and dtsi files from Linux-v4.18-rc3
with below commit:
commit 5d9ef839f874f4e3923c8a9ae7b136c6c3912cd5
Author: Stefan Mavrodiev <stefan@olimex.com>
Date:   Wed May 16 14:38:08 2018 +0300

    ARM: dts: sun7i: Add Olimex A20-SOM-EVB-eMMC board

Note:
- Update sun7i-a20-primo73.dts as per Linux, since
  this dts is U-Boot specific.
- Drop sun7i-a20-olimex-som-evb-emmc.dts since no board
  added for this.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

1 files changed, 24 insertions, 34 deletions

diff --git a/arch/arm/dts/sun7i-a20-primo73.dts b/arch/arm/dts/sun7i-a20-primo73.dts
index 0658f82675..b7294e0348 100644
--- a/arch/arm/dts/sun7i-a20-primo73.dts
+++ b/arch/arm/dts/sun7i-a20-primo73.dts
@@ -60,43 +60,33 @@
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
+};
 
-	soc@01c00000 {
-		mmc0: mmc@01c0f000 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
-			vmmc-supply = <&reg_vcc3v3>;
-			bus-width = <4>;
-			cd-gpios = <&pio 7 1 0>; /* PH1 */
-			cd-inverted;
-			status = "okay";
-		};
-
-		usbphy: phy@01c13400 {
-			usb2_vbus-supply = <&reg_usb2_vbus>;
-			status = "okay";
-		};
+&ehci1 {
+	status = "okay";
+};
 
-		ehci1: usb@01c1c000 {
-			/* rtl8188etv wifi is connected here */
-			status = "okay";
-		};
+&mmc0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins_a>;
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */
+	status = "okay";
+};
 
-		pinctrl@01c20800 {
-			usb2_vbus_pin_a: usb2_vbus_pin@0 {
-				allwinner,pins = "PH12";
-			};
-		};
+&reg_usb2_vbus {
+	gpio = <&pio 7 12 0>; /* PH12 */
+	status = "okay";
+};
 
-		uart0: serial@01c28000 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&uart0_pins_a>;
-			status = "okay";
-		};
-	};
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins_a>;
+	status = "okay";
+};
 
-	reg_usb2_vbus: usb2-vbus {
-		gpio = <&pio 7 12 0>; /* PH12 */
-		status = "okay";
-	};
+&usbphy {
+	usb2_vbus-supply = <&reg_usb2_vbus>;
+	status = "okay";
 };