summaryrefslogtreecommitdiff
path: root/arch/arm/dts/sun8i-a83t-bananapi-m3.dts
diff options
context:
space:
mode:
authorJagan Teki <jagan@amarulasolutions.com>2018-08-05 00:40:12 +0530
committerJagan Teki <jagan@amarulasolutions.com>2018-08-13 13:07:35 +0530
commit0ca4d40cfe598b55c377fffdee1970c44e73fbda (patch)
treeff8f6a8671dbc83b535094b3c66e45b7ee8139cd /arch/arm/dts/sun8i-a83t-bananapi-m3.dts
parentcf6822574251c73133d1b4943fbe9b054f8f70e5 (diff)
ARM: dts: sun8i: Update A83T dts(i) files from Linux-v4.18-rc3
Update all A83T devicetree dtsi and dtsi files from Linux-v4.18-rc3 with below commit: commit 221cb9fd2ee3042689fe0e6613d0f34eb46a5af6 Author: Mylène Josserand <mylene.josserand@bootlin.com> Date: Fri May 4 21:05:44 2018 +0200 ARM: dts: sun8i: Add enable-method for SMP support for the A83T SoC Note: bananapi-m3 and cubietruck-plus board dts files has usb_otg enabled in U-Boot which were not present in Linux. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Diffstat (limited to 'arch/arm/dts/sun8i-a83t-bananapi-m3.dts')
-rw-r--r--arch/arm/dts/sun8i-a83t-bananapi-m3.dts298
1 files changed, 293 insertions, 5 deletions
diff --git a/arch/arm/dts/sun8i-a83t-bananapi-m3.dts b/arch/arm/dts/sun8i-a83t-bananapi-m3.dts
index dfc16a0272..eaff6fa401 100644
--- a/arch/arm/dts/sun8i-a83t-bananapi-m3.dts
+++ b/arch/arm/dts/sun8i-a83t-bananapi-m3.dts
@@ -1,6 +1,7 @@
/*
- * Copyright 2015 Vishnu Patekar
- * Vishnu Patekar <vishnupatekar0510@gmail.com>
+ * Copyright 2017 Chen-Yu Tsai
+ *
+ * Chen-Yu Tsai <wens@csie.org>
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
@@ -44,29 +45,316 @@
/dts-v1/;
#include "sun8i-a83t.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
/ {
- model = "Allwinner A83T BananaPi M3 Board v1.2";
- compatible = "bananapi,m3v1.2", "allwinner,sun8i-a83t";
+ model = "Banana Pi BPI-M3";
+ compatible = "sinovoip,bpi-m3", "allwinner,sun8i-a83t";
aliases {
+ ethernet0 = &emac;
serial0 = &uart0;
};
chosen {
stdout-path = "serial0:115200n8";
};
+
+ connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ blue {
+ label = "bananapi-m3:blue:usr";
+ gpios = <&axp_gpio 1 GPIO_ACTIVE_HIGH>;
+ };
+
+ green {
+ label = "bananapi-m3:green:usr";
+ gpios = <&axp_gpio 0 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ reg_usb1_vbus: reg-usb1-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb1-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-boot-on;
+ enable-active-high;
+ gpio = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* PD24 */
+ };
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ clocks = <&ac100_rtc 1>;
+ clock-names = "ext_clock";
+ /* The WiFi low power clock must be 32768 Hz */
+ assigned-clocks = <&ac100_rtc 1>;
+ assigned-clock-rates = <32768>;
+ /* enables internal regulator and de-asserts reset */
+ reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 WL-PMU-EN */
+ };
+};
+
+&de {
+ status = "okay";
};
&ehci0 {
+ /* Terminus Tech FE 1.1s 4-port USB 2.0 hub here */
status = "okay";
+
+ /* TODO GL830 USB-to-SATA bridge downstream w/ GPIO power controls */
+};
+
+&emac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&emac_rgmii_pins>;
+ phy-supply = <&reg_sw>;
+ phy-handle = <&rgmii_phy>;
+ phy-mode = "rgmii";
+ allwinner,rx-delay-ps = <700>;
+ allwinner,tx-delay-ps = <700>;
+ status = "okay";
+};
+
+&hdmi {
+ status = "okay";
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
+&mdio {
+ rgmii_phy: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ };
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins>;
+ vmmc-supply = <&reg_dcdc1>;
+ bus-width = <4>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
+ status = "okay";
+};
+
+&mmc1 {
+ vmmc-supply = <&reg_dldo1>;
+ vqmmc-supply = <&reg_dldo1>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+
+ brcmf: wifi@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ interrupt-parent = <&r_pio>;
+ interrupts = <0 3 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-names = "host-wake";
+ };
+};
+
+&mmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_8bit_emmc_pins>;
+ vmmc-supply = <&reg_dcdc1>;
+ vqmmc-supply = <&reg_dcdc1>;
+ bus-width = <8>;
+ non-removable;
+ cap-mmc-hw-reset;
+ status = "okay";
+};
+
+&r_rsb {
+ status = "okay";
+
+ axp81x: pmic@3a3 {
+ compatible = "x-powers,axp813";
+ reg = <0x3a3>;
+ interrupt-parent = <&r_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ eldoin-supply = <&reg_dcdc1>;
+ fldoin-supply = <&reg_dcdc5>;
+ swin-supply = <&reg_dcdc1>;
+ x-powers,drive-vbus-en;
+ };
+
+ ac100: codec@e89 {
+ compatible = "x-powers,ac100";
+ reg = <0xe89>;
+
+ ac100_codec: codec {
+ compatible = "x-powers,ac100-codec";
+ interrupt-parent = <&r_pio>;
+ interrupts = <0 11 IRQ_TYPE_LEVEL_LOW>; /* PL11 */
+ #clock-cells = <0>;
+ clock-output-names = "4M_adda";
+ };
+
+ ac100_rtc: rtc {
+ compatible = "x-powers,ac100-rtc";
+ interrupt-parent = <&r_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&ac100_codec>;
+ #clock-cells = <1>;
+ clock-output-names = "cko1_rtc",
+ "cko2_rtc",
+ "cko3_rtc";
+ };
+ };
+};
+
+#include "axp81x.dtsi"
+
+&reg_aldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc-1v8";
+};
+
+&reg_aldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "dram-pll";
+};
+
+&reg_aldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "avcc";
+};
+
+&reg_dcdc1 {
+ /* schematics says 3.1V but FEX file says 3.3V */
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-3v3";
+};
+
+&reg_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-cpua";
+};
+
+&reg_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-cpub";
+};
+
+&reg_dcdc4 {
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-gpu";
+};
+
+&reg_dcdc5 {
+ regulator-always-on;
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-name = "vcc-dram";
+};
+
+&reg_dcdc6 {
+ regulator-always-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+ regulator-name = "vdd-sys";
+};
+
+&reg_dldo1 {
+ /*
+ * This powers both the WiFi/BT module's main power, I/O supply,
+ * and external pull-ups on all the data lines. It should be set
+ * to the same voltage as the I/O supply (DCDC1 in this case) to
+ * avoid any leakage or mismatch.
+ */
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi";
+};
+
+&reg_dldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ regulator-name = "vcc-pd";
+};
+
+&reg_drivevbus {
+ regulator-name = "usb0-vbus";
+ status = "okay";
+};
+
+&reg_fldo1 {
+ regulator-min-microvolt = <1080000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd12-hsic";
+};
+
+&reg_fldo2 {
+ /*
+ * Despite the embedded CPUs core not being used in any way,
+ * this must remain on or the system will hang.
+ */
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-cpus";
+};
+
+&reg_rtc_ldo {
+ regulator-name = "vcc-rtc";
+};
+
+&reg_sw {
+ /*
+ * The PHY requires 20ms after all voltages
+ * are applied until core logic is ready and
+ * 30ms after the reset pin is de-asserted.
+ * Set a 100ms delay to account for PMIC
+ * ramp time and board traces.
+ */
+ regulator-enable-ramp-delay = <100000>;
+ regulator-name = "vcc-ephy";
};
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_b>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
&usb_otg {
status = "okay";
};
+
+&usbphy {
+ usb1_vbus-supply = <&reg_usb1_vbus>;
+ status = "okay";
+};