sunxi: H3/H5 Sync DT files from upstream Linux kernel as of next-20200108

Sync the device tree files and device tree header files from upstream
Linux kernel, as of 2020-01-08. The commit synced to in the sunxi repo

    98d25b0b266d Merge branch 'sunxi/dt-for-5.6' into sunxi/for-next

which is also part of next-20200108.

Changes brought in include:

  - cleanup of pinmux node names
  - addition of Security ID, MBUS, CSI, crypto engine, video codec,
    pmu, and thermal sensor device nodes for both SoCs
  - addition of deinterlacing engine device node on H3
  - cleanup of RTC device node and addition of its clocks
  - various board cleanups and improvements
    - removal of pinmux node for GPIO lines
    - cpufreq / DVFS
    - HDMI output
    - UART-based Bluetooth
    - audio codec
    - USB ports
  - new boards

Most of the changes don't concern U-boot.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>

1 files changed, 152 insertions, 0 deletions

diff --git a/arch/arm/dts/sun8i-h3-mapleboard-mp130.dts b/arch/arm/dts/sun8i-h3-mapleboard-mp130.dts
new file mode 100644
index 0000000000..ff0a7a952e
--- /dev/null
+++ b/arch/arm/dts/sun8i-h3-mapleboard-mp130.dts
@@ -0,0 +1,152 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2017 Centrum Embedded Systems, Jia-Bin Huang <jb@ces.com.tw>
+ * Copyright (C) 2018 Jonathan McDowell <noodles@earth.li>
+ */
+
+/dts-v1/;
+#include "sun8i-h3.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "MapleBoard MP130";
+	compatible = "mapleboard,mp130", "allwinner,sun8i-h3";
+
+	aliases {
+		ethernet0 = &emac;
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		pwr_led {
+			label = "mp130:orange:pwr";
+			gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+
+		status_led {
+			label = "mp130:orange:status";
+			gpios = <&pio 0 10 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	r_gpio_keys {
+		compatible = "gpio-keys";
+
+		power {
+			label = "power";
+			linux,code = <KEY_POWER>;
+			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>; /* PL3 */
+		};
+
+		user {
+			label = "user";
+			linux,code = <BTN_0>;
+			gpios = <&r_pio 0 4 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&codec {
+	allwinner,audio-routing =
+		"Line Out", "LINEOUT",
+		"LINEIN", "Line In";
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&ehci2 {
+	status = "okay";
+};
+
+&ehci3 {
+	status = "okay";
+};
+
+&emac {
+	phy-handle = <&int_mii_phy>;
+	phy-mode = "mii";
+	allwinner,leds-active-low;
+	status = "okay";
+};
+
+&ir {
+	pinctrl-names = "default";
+	pinctrl-0 = <&r_ir_rx_pin>;
+	status = "okay";
+};
+
+&mmc0 {
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
+	status = "okay";
+};
+
+&mmc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_8bit_pins>;
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <8>;
+	non-removable;
+	cap-mmc-hw-reset;
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&ohci2 {
+	status = "okay";
+};
+
+&ohci3 {
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pa_pins>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>;
+	status = "disabled";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart2_pins>;
+	status = "disabled";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart3_pins>;
+	status = "disabled";
+};
+
+&usb_otg {
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
+&usbphy {
+	/* USB VBUS is always on */
+	status = "okay";
+};