arm64: zynqmp: Add support for zcu104 customer board

Xilinx zcu104 is another customer board. It is sort of zcu102 clone with
some differences.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

1 files changed, 266 insertions, 0 deletions

diff --git a/arch/arm/dts/zynqmp-zcu104-revC.dts b/arch/arm/dts/zynqmp-zcu104-revC.dts
new file mode 100644
index 0000000000..6e3cf5a97f
--- /dev/null
+++ b/arch/arm/dts/zynqmp-zcu104-revC.dts
@@ -0,0 +1,266 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * dts file for Xilinx ZynqMP ZCU104
+ *
+ * (C) Copyright 2017 - 2018, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+/dts-v1/;
+
+#include "zynqmp.dtsi"
+#include "zynqmp-clk-ccf.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/phy/phy.h>
+
+/ {
+	model = "ZynqMP ZCU104 RevC";
+	compatible = "xlnx,zynqmp-zcu104-revC", "xlnx,zynqmp-zcu104", "xlnx,zynqmp";
+
+	aliases {
+		ethernet0 = &gem3;
+		gpio0 = &gpio;
+		i2c0 = &i2c1;
+		mmc0 = &sdhci1;
+		rtc0 = &rtc;
+		serial0 = &uart0;
+		serial1 = &uart1;
+		serial2 = &dcc;
+		spi0 = &qspi;
+		usb0 = &usb0;
+	};
+
+	chosen {
+		bootargs = "earlycon";
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x80000000>;
+	};
+};
+
+&can1 {
+	status = "okay";
+};
+
+&dcc {
+	status = "okay";
+};
+
+&gem3 {
+	status = "okay";
+	phy-handle = <&phy0>;
+	phy-mode = "rgmii-id";
+	phy0: phy@c {
+		reg = <0xc>;
+		ti,rx-internal-delay = <0x8>;
+		ti,tx-internal-delay = <0xa>;
+		ti,fifo-depth = <0x1>;
+	};
+};
+
+&gpio {
+	status = "okay";
+};
+
+&gpu {
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	tca6416_u97: gpio@21 {
+		compatible = "ti,tca6416";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		/*
+		 * IRQ not connected
+		 * Lines:
+		 * 0 - IRPS5401_ALERT_B
+		 * 1 - HDMI_8T49N241_INT_ALM
+		 * 2 - MAX6643_OT_B
+		 * 3 - MAX6643_FANFAIL_B
+		 * 5 - IIC_MUX_RESET_B
+		 * 6 - GEM3_EXP_RESET_B
+		 * 7 - FMC_LPC_PRSNT_M2C_B
+		 * 4, 10 - 17 - not connected
+		 */
+	};
+
+	/* Another connection to this bus via PL i2c via PCA9306 - u45 */
+	i2c-mux@74 { /* u34 */
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x74>;
+		i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			/*
+			 * IIC_EEPROM 1kB memory which uses 256B blocks
+			 * where every block has different address.
+			 *    0 - 256B address 0x54
+			 * 256B - 512B address 0x55
+			 * 512B - 768B address 0x56
+			 * 768B - 1024B address 0x57
+			 */
+			eeprom: eeprom@54 { /* u23 */
+				compatible = "atmel,24c08";
+				reg = <0x54>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+			};
+		};
+
+		i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			clock_8t49n287: clock-generator@6c { /* 8T49N287 - u182 */
+				compatible = "idt,8t49n287";
+				reg = <0x6c>;
+			};
+		};
+
+		i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			irps5401_43: irps54012@43 { /* IRPS5401 - u175 */
+				#clock-cells = <0>;
+				compatible = "infineon,irps5401";
+				reg = <0x43>;
+			};
+			irps5401_4d: irps54012@4d { /* IRPS5401 - u180 */
+				#clock-cells = <0>;
+				compatible = "infineon,irps5401";
+				reg = <0x4d>;
+			};
+		};
+
+		i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+		};
+
+		i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+		};
+
+		i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <7>;
+		};
+
+		/* 3, 6 not connected */
+	};
+};
+
+&qspi {
+	status = "okay";
+	flash@0 {
+		compatible = "m25p80"; /* n25q512a 128MiB */
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0x0>;
+		spi-tx-bus-width = <1>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <108000000>; /* Based on DC1 spec */
+		partition@qspi-fsbl-uboot { /* for testing purpose */
+			label = "qspi-fsbl-uboot";
+			reg = <0x0 0x100000>;
+		};
+		partition@qspi-linux { /* for testing purpose */
+			label = "qspi-linux";
+			reg = <0x100000 0x500000>;
+		};
+		partition@qspi-device-tree { /* for testing purpose */
+			label = "qspi-device-tree";
+			reg = <0x600000 0x20000>;
+		};
+		partition@qspi-rootfs { /* for testing purpose */
+			label = "qspi-rootfs";
+			reg = <0x620000 0x5E0000>;
+		};
+	};
+};
+
+&rtc {
+	status = "okay";
+};
+
+&sata {
+	status = "okay";
+	/* SATA OOB timing settings */
+	ceva,p0-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>;
+	ceva,p0-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
+	ceva,p0-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
+	ceva,p0-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
+	ceva,p1-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>;
+	ceva,p1-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
+	ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
+	ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
+	phy-names = "sata-phy";
+	phys = <&lane3 PHY_TYPE_SATA 1 1 125000000>;
+};
+
+/* SD1 with level shifter */
+&sdhci1 {
+	status = "okay";
+	no-1-8-v;
+	xlnx,mio_bank = <1>;
+	disable-wp;
+};
+
+&serdes {
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+/* ULPI SMSC USB3320 */
+&usb0 {
+	status = "okay";
+};
+
+&dwc3_0 {
+	status = "okay";
+	dr_mode = "host";
+	snps,usb3_lpm_capable;
+	phy-names = "usb3-phy";
+	phys = <&lane2 PHY_TYPE_USB3 0 2 26000000>;
+	maximum-speed = "super-speed";
+};
+
+&watchdog0 {
+	status = "okay";
+};
+
+&xilinx_ams {
+	status = "okay";
+};
+
+&ams_ps {
+	status = "okay";
+};
+
+&ams_pl {
+	status = "okay";
+};