tegra2: Add more clock functions

This adds most of the clock functions required by board and driver code:

-query and adjust peripheral clocks
-query and adjust PLLs
-reset and enable control

These functions are plumbed in as required.

Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Warren <twarren@nvidia.com>

4 files changed, 943 insertions, 73 deletions

diff --git a/arch/arm/cpu/armv7/tegra2/ap20.c b/arch/arm/cpu/armv7/tegra2/ap20.c
index 64d4c69d24..5cb4b1b6a0 100644
--- a/arch/arm/cpu/armv7/tegra2/ap20.c
+++ b/arch/arm/cpu/armv7/tegra2/ap20.c
@@ -189,7 +189,6 @@ static void reset_A9_cpu(int reset)
 
 static void clock_enable_coresight(int enable)
 {
-	struct clk_rst_ctlr *clkrst = (struct clk_rst_ctlr *)NV_PA_CLK_RST_BASE;
 	u32 rst, src;
 
 	clock_set_enable(PERIPH_ID_CORESIGHT, enable);
@@ -203,7 +202,7 @@ static void clock_enable_coresight(int enable)
 		 *  (bits 7:0), so 00000001b == 1.5 (n+1 + .5)
 		 */
 		src = CLK_DIVIDER(NVBL_PLLP_KHZ, 144000);
-		writel(src, &clkrst->crc_clk_src_csite);
+		clock_ll_set_source_divisor(PERIPH_ID_CSI, 0, src);
 
 		/* Unlock the CPU CoreSight interfaces */
 		rst = 0xC5ACCE55;
diff --git a/arch/arm/cpu/armv7/tegra2/clock.c b/arch/arm/cpu/armv7/tegra2/clock.c
index 5aa64821e4..03ac1e3ed0 100644
--- a/arch/arm/cpu/armv7/tegra2/clock.c
+++ b/arch/arm/cpu/armv7/tegra2/clock.c
@@ -27,6 +27,371 @@
 #include <asm/arch/timer.h>
 #include <asm/arch/tegra2.h>
 #include <common.h>
+#include <div64.h>
+
+/*
+ * This is our record of the current clock rate of each clock. We don't
+ * fill all of these in since we are only really interested in clocks which
+ * we use as parents.
+ */
+static unsigned pll_rate[CLOCK_ID_COUNT];
+
+/*
+ * The oscillator frequency is fixed to one of four set values. Based on this
+ * the other clocks are set up appropriately.
+ */
+static unsigned osc_freq[CLOCK_OSC_FREQ_COUNT] = {
+	13000000,
+	19200000,
+	12000000,
+	26000000,
+};
+
+/*
+ * Clock types that we can use as a source. The Tegra2 has muxes for the
+ * peripheral clocks, and in most cases there are four options for the clock
+ * source. This gives us a clock 'type' and exploits what commonality exists
+ * in the device.
+ *
+ * Letters are obvious, except for T which means CLK_M, and S which means the
+ * clock derived from 32KHz. Beware that CLK_M (also called OSC in the
+ * datasheet) and PLL_M are different things. The former is the basic
+ * clock supplied to the SOC from an external oscillator. The latter is the
+ * memory clock PLL.
+ *
+ * See definitions in clock_id in the header file.
+ */
+enum clock_type_id {
+	CLOCK_TYPE_AXPT,	/* PLL_A, PLL_X, PLL_P, CLK_M */
+	CLOCK_TYPE_MCPA,	/* and so on */
+	CLOCK_TYPE_MCPT,
+	CLOCK_TYPE_PCM,
+	CLOCK_TYPE_PCMT,
+	CLOCK_TYPE_PCXTS,
+	CLOCK_TYPE_PDCT,
+
+	CLOCK_TYPE_COUNT,
+	CLOCK_TYPE_NONE = -1,	/* invalid clock type */
+};
+
+/* return 1 if a peripheral ID is in range */
+#define clock_type_id_isvalid(id) ((id) >= 0 && \
+		(id) < CLOCK_TYPE_COUNT)
+
+char pllp_valid = 1;	/* PLLP is set up correctly */
+
+enum {
+	CLOCK_MAX_MUX	= 4	/* number of source options for each clock */
+};
+
+/*
+ * Clock source mux for each clock type. This just converts our enum into
+ * a list of mux sources for use by the code. Note that CLOCK_TYPE_PCXTS
+ * is special as it has 5 sources. Since it also has a different number of
+ * bits in its register for the source, we just handle it with a special
+ * case in the code.
+ */
+#define CLK(x) CLOCK_ID_ ## x
+static enum clock_id clock_source[CLOCK_TYPE_COUNT][CLOCK_MAX_MUX] = {
+	{ CLK(AUDIO),	CLK(XCPU),	CLK(PERIPH),	CLK(OSC)	},
+	{ CLK(MEMORY),	CLK(CGENERAL),	CLK(PERIPH),	CLK(AUDIO)	},
+	{ CLK(MEMORY),	CLK(CGENERAL),	CLK(PERIPH),	CLK(OSC)	},
+	{ CLK(PERIPH),	CLK(CGENERAL),	CLK(MEMORY),	CLK(NONE)	},
+	{ CLK(PERIPH),	CLK(CGENERAL),	CLK(MEMORY),	CLK(OSC)	},
+	{ CLK(PERIPH),	CLK(CGENERAL),	CLK(XCPU),	CLK(OSC)	},
+	{ CLK(PERIPH),	CLK(DISPLAY),	CLK(CGENERAL),	CLK(OSC)	},
+};
+
+/*
+ * Clock peripheral IDs which sadly don't match up with PERIPH_ID. This is
+ * not in the header file since it is for purely internal use - we want
+ * callers to use the PERIPH_ID for all access to peripheral clocks to avoid
+ * confusion bewteen PERIPH_ID_... and PERIPHC_...
+ *
+ * We don't call this CLOCK_PERIPH_ID or PERIPH_CLOCK_ID as it would just be
+ * confusing.
+ *
+ * Note to SOC vendors: perhaps define a unified numbering for peripherals and
+ * use it for reset, clock enable, clock source/divider and even pinmuxing
+ * if you can.
+ */
+enum periphc_internal_id {
+	/* 0x00 */
+	PERIPHC_I2S1,
+	PERIPHC_I2S2,
+	PERIPHC_SPDIF_OUT,
+	PERIPHC_SPDIF_IN,
+	PERIPHC_PWM,
+	PERIPHC_SPI1,
+	PERIPHC_SPI2,
+	PERIPHC_SPI3,
+
+	/* 0x08 */
+	PERIPHC_XIO,
+	PERIPHC_I2C1,
+	PERIPHC_DVC_I2C,
+	PERIPHC_TWC,
+	PERIPHC_0c,
+	PERIPHC_10,	/* PERIPHC_SPI1, what is this really? */
+	PERIPHC_DISP1,
+	PERIPHC_DISP2,
+
+	/* 0x10 */
+	PERIPHC_CVE,
+	PERIPHC_IDE0,
+	PERIPHC_VI,
+	PERIPHC_1c,
+	PERIPHC_SDMMC1,
+	PERIPHC_SDMMC2,
+	PERIPHC_G3D,
+	PERIPHC_G2D,
+
+	/* 0x18 */
+	PERIPHC_NDFLASH,
+	PERIPHC_SDMMC4,
+	PERIPHC_VFIR,
+	PERIPHC_EPP,
+	PERIPHC_MPE,
+	PERIPHC_MIPI,
+	PERIPHC_UART1,
+	PERIPHC_UART2,
+
+	/* 0x20 */
+	PERIPHC_HOST1X,
+	PERIPHC_21,
+	PERIPHC_TVO,
+	PERIPHC_HDMI,
+	PERIPHC_24,
+	PERIPHC_TVDAC,
+	PERIPHC_I2C2,
+	PERIPHC_EMC,
+
+	/* 0x28 */
+	PERIPHC_UART3,
+	PERIPHC_29,
+	PERIPHC_VI_SENSOR,
+	PERIPHC_2b,
+	PERIPHC_2c,
+	PERIPHC_SPI4,
+	PERIPHC_I2C3,
+	PERIPHC_SDMMC3,
+
+	/* 0x30 */
+	PERIPHC_UART4,
+	PERIPHC_UART5,
+	PERIPHC_VDE,
+	PERIPHC_OWR,
+	PERIPHC_NOR,
+	PERIPHC_CSITE,
+
+	PERIPHC_COUNT,
+
+	PERIPHC_NONE = -1,
+};
+
+/* return 1 if a periphc_internal_id is in range */
+#define periphc_internal_id_isvalid(id) ((id) >= 0 && \
+		(id) < PERIPHC_COUNT)
+
+/*
+ * Clock type for each peripheral clock source. We put the name in each
+ * record just so it is easy to match things up
+ */
+#define TYPE(name, type) type
+static enum clock_type_id clock_periph_type[PERIPHC_COUNT] = {
+	/* 0x00 */
+	TYPE(PERIPHC_I2S1,	CLOCK_TYPE_AXPT),
+	TYPE(PERIPHC_I2S2,	CLOCK_TYPE_AXPT),
+	TYPE(PERIPHC_SPDIF_OUT,	CLOCK_TYPE_AXPT),
+	TYPE(PERIPHC_SPDIF_IN,	CLOCK_TYPE_PCM),
+	TYPE(PERIPHC_PWM,	CLOCK_TYPE_PCXTS),
+	TYPE(PERIPHC_SPI1,	CLOCK_TYPE_PCMT),
+	TYPE(PERIPHC_SPI22,	CLOCK_TYPE_PCMT),
+	TYPE(PERIPHC_SPI3,	CLOCK_TYPE_PCMT),
+
+	/* 0x08 */
+	TYPE(PERIPHC_XIO,	CLOCK_TYPE_PCMT),
+	TYPE(PERIPHC_I2C1,	CLOCK_TYPE_PCMT),
+	TYPE(PERIPHC_DVC_I2C,	CLOCK_TYPE_PCMT),
+	TYPE(PERIPHC_TWC,	CLOCK_TYPE_PCMT),
+	TYPE(PERIPHC_NONE,	CLOCK_TYPE_NONE),
+	TYPE(PERIPHC_SPI1,	CLOCK_TYPE_PCMT),
+	TYPE(PERIPHC_DISP1,	CLOCK_TYPE_PDCT),
+	TYPE(PERIPHC_DISP2,	CLOCK_TYPE_PDCT),
+
+	/* 0x10 */
+	TYPE(PERIPHC_CVE,	CLOCK_TYPE_PDCT),
+	TYPE(PERIPHC_IDE0,	CLOCK_TYPE_PCMT),
+	TYPE(PERIPHC_VI,	CLOCK_TYPE_MCPA),
+	TYPE(PERIPHC_NONE,	CLOCK_TYPE_NONE),
+	TYPE(PERIPHC_SDMMC1,	CLOCK_TYPE_PCMT),
+	TYPE(PERIPHC_SDMMC2,	CLOCK_TYPE_PCMT),
+	TYPE(PERIPHC_G3D,	CLOCK_TYPE_MCPA),
+	TYPE(PERIPHC_G2D,	CLOCK_TYPE_MCPA),
+
+	/* 0x18 */
+	TYPE(PERIPHC_NDFLASH,	CLOCK_TYPE_PCMT),
+	TYPE(PERIPHC_SDMMC4,	CLOCK_TYPE_PCMT),
+	TYPE(PERIPHC_VFIR,	CLOCK_TYPE_PCMT),
+	TYPE(PERIPHC_EPP,	CLOCK_TYPE_MCPA),
+	TYPE(PERIPHC_MPE,	CLOCK_TYPE_MCPA),
+	TYPE(PERIPHC_MIPI,	CLOCK_TYPE_PCMT),
+	TYPE(PERIPHC_UART1,	CLOCK_TYPE_PCMT),
+	TYPE(PERIPHC_UART2,	CLOCK_TYPE_PCMT),
+
+	/* 0x20 */
+	TYPE(PERIPHC_HOST1X,	CLOCK_TYPE_MCPA),
+	TYPE(PERIPHC_NONE,	CLOCK_TYPE_NONE),
+	TYPE(PERIPHC_TVO,	CLOCK_TYPE_PDCT),
+	TYPE(PERIPHC_HDMI,	CLOCK_TYPE_PDCT),
+	TYPE(PERIPHC_NONE,	CLOCK_TYPE_NONE),
+	TYPE(PERIPHC_TVDAC,	CLOCK_TYPE_PDCT),
+	TYPE(PERIPHC_I2C2,	CLOCK_TYPE_PCMT),
+	TYPE(PERIPHC_EMC,	CLOCK_TYPE_MCPT),
+
+	/* 0x28 */
+	TYPE(PERIPHC_UART3,	CLOCK_TYPE_PCMT),
+	TYPE(PERIPHC_NONE,	CLOCK_TYPE_NONE),
+	TYPE(PERIPHC_VI,	CLOCK_TYPE_MCPA),
+	TYPE(PERIPHC_NONE,	CLOCK_TYPE_NONE),
+	TYPE(PERIPHC_NONE,	CLOCK_TYPE_NONE),
+	TYPE(PERIPHC_SPI4,	CLOCK_TYPE_PCMT),
+	TYPE(PERIPHC_I2C3,	CLOCK_TYPE_PCMT),
+	TYPE(PERIPHC_SDMMC3,	CLOCK_TYPE_PCMT),
+
+	/* 0x30 */
+	TYPE(PERIPHC_UART4,	CLOCK_TYPE_PCMT),
+	TYPE(PERIPHC_UART5,	CLOCK_TYPE_PCMT),
+	TYPE(PERIPHC_VDE,	CLOCK_TYPE_PCMT),
+	TYPE(PERIPHC_OWR,	CLOCK_TYPE_PCMT),
+	TYPE(PERIPHC_NOR,	CLOCK_TYPE_PCMT),
+	TYPE(PERIPHC_CSITE,	CLOCK_TYPE_PCMT),
+};
+
+/*
+ * This array translates a periph_id to a periphc_internal_id
+ *
+ * Not present/matched up:
+ *	uint vi_sensor;	 _VI_SENSOR_0,		0x1A8
+ *	SPDIF - which is both 0x08 and 0x0c
+ *
+ */
+#define NONE(name) (-1)
+#define OFFSET(name, value) PERIPHC_ ## name
+static s8 periph_id_to_internal_id[PERIPH_ID_COUNT] = {
+	/* Low word: 31:0 */
+	NONE(CPU),
+	NONE(RESERVED1),
+	NONE(RESERVED2),
+	NONE(AC97),
+	NONE(RTC),
+	NONE(TMR),
+	PERIPHC_UART1,
+	PERIPHC_UART2,	/* and vfir 0x68 */
+
+	/* 0x08 */
+	NONE(GPIO),
+	PERIPHC_SDMMC2,
+	NONE(SPDIF),		/* 0x08 and 0x0c, unclear which to use */
+	PERIPHC_I2S1,
+	PERIPHC_I2C1,
+	PERIPHC_NDFLASH,
+	PERIPHC_SDMMC1,
+	PERIPHC_SDMMC4,
+
+	/* 0x10 */
+	PERIPHC_TWC,
+	PERIPHC_PWM,
+	PERIPHC_I2S2,
+	PERIPHC_EPP,
+	PERIPHC_VI,
+	PERIPHC_G2D,
+	NONE(USBD),
+	NONE(ISP),
+
+	/* 0x18 */
+	PERIPHC_G3D,
+	PERIPHC_IDE0,
+	PERIPHC_DISP2,
+	PERIPHC_DISP1,
+	PERIPHC_HOST1X,
+	NONE(VCP),
+	NONE(RESERVED30),
+	NONE(CACHE2),
+
+	/* Middle word: 63:32 */
+	NONE(MEM),
+	NONE(AHBDMA),
+	NONE(APBDMA),
+	NONE(RESERVED35),
+	NONE(KBC),
+	NONE(STAT_MON),
+	NONE(PMC),
+	NONE(FUSE),
+
+	/* 0x28 */
+	NONE(KFUSE),
+	NONE(SBC1),	/* SBC1, 0x34, is this SPI1? */
+	PERIPHC_NOR,
+	PERIPHC_SPI1,
+	PERIPHC_SPI2,
+	PERIPHC_XIO,
+	PERIPHC_SPI3,
+	PERIPHC_DVC_I2C,
+
+	/* 0x30 */
+	NONE(DSI),
+	PERIPHC_TVO,	/* also CVE 0x40 */
+	PERIPHC_MIPI,
+	PERIPHC_HDMI,
+	PERIPHC_CSITE,
+	PERIPHC_TVDAC,
+	PERIPHC_I2C2,
+	PERIPHC_UART3,
+
+	/* 0x38 */
+	NONE(RESERVED56),
+	PERIPHC_EMC,
+	NONE(USB2),
+	NONE(USB3),
+	PERIPHC_MPE,
+	PERIPHC_VDE,
+	NONE(BSEA),
+	NONE(BSEV),
+
+	/* Upper word 95:64 */
+	NONE(SPEEDO),
+	PERIPHC_UART4,
+	PERIPHC_UART5,
+	PERIPHC_I2C3,
+	PERIPHC_SPI4,
+	PERIPHC_SDMMC3,
+	NONE(PCIE),
+	PERIPHC_OWR,
+
+	/* 0x48 */
+	NONE(AFI),
+	NONE(CORESIGHT),
+	NONE(RESERVED74),
+	NONE(AVPUCQ),
+	NONE(RESERVED76),
+	NONE(RESERVED77),
+	NONE(RESERVED78),
+	NONE(RESERVED79),
+
+	/* 0x50 */
+	NONE(RESERVED80),
+	NONE(RESERVED81),
+	NONE(RESERVED82),
+	NONE(RESERVED83),
+	NONE(IRAMA),
+	NONE(IRAMB),
+	NONE(IRAMC),
+	NONE(IRAMD),
+
+	/* 0x58 */
+	NONE(CRAM2),
+};
 
 /*
  * Get the oscillator frequency, from the corresponding hardware configuration
@@ -42,16 +407,21 @@ enum clock_osc_freq clock_get_osc_freq(void)
 	return (reg & OSC_FREQ_MASK) >> OSC_FREQ_SHIFT;
 }
 
-unsigned long clock_start_pll(enum clock_id clkid, u32 divm, u32 divn,
-		u32 divp, u32 cpcon, u32 lfcon)
+/* Returns a pointer to the registers of the given pll */
+static struct clk_pll *get_pll(enum clock_id clkid)
 {
 	struct clk_rst_ctlr *clkrst =
 			(struct clk_rst_ctlr *)NV_PA_CLK_RST_BASE;
-	u32 data;
-	struct clk_pll *pll;
 
 	assert(clock_id_isvalid(clkid));
-	pll = &clkrst->crc_pll[clkid];
+	return &clkrst->crc_pll[clkid];
+}
+
+unsigned long clock_start_pll(enum clock_id clkid, u32 divm, u32 divn,
+		u32 divp, u32 cpcon, u32 lfcon)
+{
+	struct clk_pll *pll = get_pll(clkid);
+	u32 data;
 
 	/*
 	 * We cheat by treating all PLL (except PLLU) in the same fashion.
@@ -76,6 +446,294 @@ unsigned long clock_start_pll(enum clock_id clkid, u32 divm, u32 divn,
 	return timer_get_us() + CLOCK_PLL_STABLE_DELAY_US;
 }
 
+/* return 1 if a peripheral ID is in range and valid */
+static int clock_periph_id_isvalid(enum periph_id id)
+{
+	if (id < PERIPH_ID_FIRST || id >= PERIPH_ID_COUNT)
+		printf("Peripheral id %d out of range\n", id);
+	else {
+		switch (id) {
+		case PERIPH_ID_RESERVED1:
+		case PERIPH_ID_RESERVED2:
+		case PERIPH_ID_RESERVED30:
+		case PERIPH_ID_RESERVED35:
+		case PERIPH_ID_RESERVED56:
+		case PERIPH_ID_RESERVED74:
+		case PERIPH_ID_RESERVED76:
+		case PERIPH_ID_RESERVED77:
+		case PERIPH_ID_RESERVED78:
+		case PERIPH_ID_RESERVED79:
+		case PERIPH_ID_RESERVED80:
+		case PERIPH_ID_RESERVED81:
+		case PERIPH_ID_RESERVED82:
+		case PERIPH_ID_RESERVED83:
+			printf("Peripheral id %d is reserved\n", id);
+			break;
+		default:
+			return 1;
+		}
+	}
+	return 0;
+}
+
+/* Returns a pointer to the clock source register for a peripheral */
+static u32 *get_periph_source_reg(enum periph_id periph_id)
+{
+	struct clk_rst_ctlr *clkrst =
+			(struct clk_rst_ctlr *)NV_PA_CLK_RST_BASE;
+	enum periphc_internal_id internal_id;
+
+	assert(clock_periph_id_isvalid(periph_id));
+	internal_id = periph_id_to_internal_id[periph_id];
+	assert(internal_id != -1);
+	return &clkrst->crc_clk_src[internal_id];
+}
+
+void clock_ll_set_source_divisor(enum periph_id periph_id, unsigned source,
+			      unsigned divisor)
+{
+	u32 *reg = get_periph_source_reg(periph_id);
+	u32 value;
+
+	value = readl(reg);
+
+	value &= ~OUT_CLK_SOURCE_MASK;
+	value |= source << OUT_CLK_SOURCE_SHIFT;
+
+	value &= ~OUT_CLK_DIVISOR_MASK;
+	value |= divisor << OUT_CLK_DIVISOR_SHIFT;
+
+	writel(value, reg);
+}
+
+void clock_ll_set_source(enum periph_id periph_id, unsigned source)
+{
+	u32 *reg = get_periph_source_reg(periph_id);
+
+	clrsetbits_le32(reg, OUT_CLK_SOURCE_MASK,
+			source << OUT_CLK_SOURCE_SHIFT);
+}
+
+/**
+ * Given the parent's rate and the required rate for the children, this works
+ * out the peripheral clock divider to use, in 7.1 binary format.
+ *
+ * @param parent_rate	clock rate of parent clock in Hz
+ * @param rate		required clock rate for this clock
+ * @return divider which should be used
+ */
+static int clk_div7_1_get_divider(unsigned long parent_rate,
+				  unsigned long rate)
+{
+	u64 divider = parent_rate * 2;
+
+	divider += rate - 1;
+	do_div(divider, rate);
+
+	if ((s64)divider - 2 < 0)
+		return 0;
+
+	if ((s64)divider - 2 > 255)
+		return -1;
+
+	return divider - 2;
+}
+
+/**
+ * Given the parent's rate and the divider in 7.1 format, this works out the
+ * resulting peripheral clock rate.
+ *
+ * @param parent_rate	clock rate of parent clock in Hz
+ * @param divider which should be used in 7.1 format
+ * @return effective clock rate of peripheral
+ */
+static unsigned long get_rate_from_divider(unsigned long parent_rate,
+					   int divider)
+{
+	u64 rate;
+
+	rate = (u64)parent_rate * 2;
+	do_div(rate, divider + 2);
+	return rate;
+}
+
+unsigned long clock_get_periph_rate(enum periph_id periph_id,
+		enum clock_id parent)
+{
+	u32 *reg = get_periph_source_reg(periph_id);
+
+	return get_rate_from_divider(pll_rate[parent],
+		(readl(reg) & OUT_CLK_DIVISOR_MASK) >> OUT_CLK_DIVISOR_SHIFT);
+}
+
+/**
+ * Find the best available 7.1 format divisor given a parent clock rate and
+ * required child clock rate. This function assumes that a second-stage
+ * divisor is available which can divide by powers of 2 from 1 to 256.
+ *
+ * @param parent_rate	clock rate of parent clock in Hz
+ * @param rate		required clock rate for this clock
+ * @param extra_div	value for the second-stage divisor (not set if this
+ *			function returns -1.
+ * @return divider which should be used, or -1 if nothing is valid
+ *
+ */
+static int find_best_divider(unsigned long parent_rate, unsigned long rate,
+		int *extra_div)
+{
+	int shift;
+	int best_divider = -1;
+	int best_error = rate;
+
+	/* try dividers from 1 to 256 and find closest match */
+	for (shift = 0; shift <= 8 && best_error > 0; shift++) {
+		unsigned divided_parent = parent_rate >> shift;
+		int divider = clk_div7_1_get_divider(divided_parent, rate);
+		unsigned effective_rate = get_rate_from_divider(divided_parent,
+						       divider);
+		int error = rate - effective_rate;
+
+		/* Given a valid divider, look for the lowest error */
+		if (divider != -1 && error < best_error) {
+			best_error = error;
+			*extra_div = 1 << shift;
+			best_divider = divider;
+		}
+	}
+
+	/* return what we found - *extra_div will already be set */
+	return best_divider;
+}
+
+/**
+ * Given a peripheral ID and the required source clock, this returns which
+ * value should be programmed into the source mux for that peripheral.
+ *
+ * There is special code here to handle the one source type with 5 sources.
+ *
+ * @param periph_id	peripheral to start
+ * @param source	PLL id of required parent clock
+ * @param mux_bits	Set to number of bits in mux register: 2 or 4
+ * @return mux value (0-4, or -1 if not found)
+ */
+static int get_periph_clock_source(enum periph_id periph_id,
+		enum clock_id parent, int *mux_bits)
+{
+	enum clock_type_id type;
+	enum periphc_internal_id internal_id;
+	int mux;
+
+	assert(clock_periph_id_isvalid(periph_id));
+
+	internal_id = periph_id_to_internal_id[periph_id];
+	assert(periphc_internal_id_isvalid(internal_id));
+
+	type = clock_periph_type[internal_id];
+	assert(clock_type_id_isvalid(type));
+
+	/* Special case here for the clock with a 4-bit source mux */
+	if (type == CLOCK_TYPE_PCXTS)
+		*mux_bits = 4;
+	else
+		*mux_bits = 2;
+
+	for (mux = 0; mux < CLOCK_MAX_MUX; mux++)
+		if (clock_source[type][mux] == parent)
+			return mux;
+
+	/*
+	 * Not found: it might be looking for the 'S' in CLOCK_TYPE_PCXTS
+	 * which is not in our table. If not, then they are asking for a
+	 * source which this peripheral can't access through its mux.
+	 */
+	assert(type == CLOCK_TYPE_PCXTS);
+	assert(parent == CLOCK_ID_SFROM32KHZ);
+	if (type == CLOCK_TYPE_PCXTS && parent == CLOCK_ID_SFROM32KHZ)
+		return 4;	/* mux value for this clock */
+
+	/* if we get here, either us or the caller has made a mistake */
+	printf("Caller requested bad clock: periph=%d, parent=%d\n", periph_id,
+		parent);
+	return -1;
+}
+
+/**
+ * Adjust peripheral PLL to use the given divider and source.
+ *
+ * @param periph_id	peripheral to adjust
+ * @param parent	Required parent clock (for source mux)
+ * @param divider	Required divider in 7.1 format
+ * @return 0 if ok, -1 on error (requesting a parent clock which is not valid
+ *		for this peripheral)
+ */
+static int adjust_periph_pll(enum periph_id periph_id,
+		enum clock_id parent, unsigned divider)
+{
+	u32 *reg = get_periph_source_reg(periph_id);
+	unsigned source;
+	int mux_bits;
+
+	clrsetbits_le32(reg, OUT_CLK_DIVISOR_MASK,
+			divider << OUT_CLK_DIVISOR_SHIFT);
+	udelay(1);
+
+	/* work out the source clock and set it */
+	source = get_periph_clock_source(periph_id, parent, &mux_bits);
+	if (source < 0)
+		return -1;
+	if (mux_bits == 4) {
+		clrsetbits_le32(reg, OUT_CLK_SOURCE4_MASK,
+			source << OUT_CLK_SOURCE4_SHIFT);
+	} else {
+		clrsetbits_le32(reg, OUT_CLK_SOURCE_MASK,
+			source << OUT_CLK_SOURCE_SHIFT);
+	}
+	udelay(2);
+	return 0;
+}
+
+unsigned clock_adjust_periph_pll_div(enum periph_id periph_id,
+		enum clock_id parent, unsigned rate, int *extra_div)
+{
+	unsigned effective_rate;
+	int divider;
+
+	if (extra_div)
+		divider = find_best_divider(pll_rate[parent], rate, extra_div);
+	else
+		divider = clk_div7_1_get_divider(pll_rate[parent], rate);
+	assert(divider >= 0);
+	if (adjust_periph_pll(periph_id, parent, divider))
+		return -1U;
+	debug("periph %d, rate=%d, reg=%p = %x\n", periph_id, rate,
+		get_periph_source_reg(periph_id),
+		readl(get_periph_source_reg(periph_id)));
+
+	/* Check what we ended up with. This shouldn't matter though */
+	effective_rate = clock_get_periph_rate(periph_id, parent);
+	if (extra_div)
+		effective_rate /= *extra_div;
+	if (rate != effective_rate)
+		debug("Requested clock rate %u not honored (got %u)\n",
+		       rate, effective_rate);
+	return effective_rate;
+}
+
+unsigned clock_start_periph_pll(enum periph_id periph_id,
+		enum clock_id parent, unsigned rate)
+{
+	unsigned effective_rate;
+
+	reset_set_enable(periph_id, 1);
+	clock_enable(periph_id);
+
+	effective_rate = clock_adjust_periph_pll_div(periph_id, parent, rate,
+						 NULL);
+
+	reset_set_enable(periph_id, 0);
+	return effective_rate;
+}
+
 void clock_set_enable(enum periph_id periph_id, int enable)
 {
 	struct clk_rst_ctlr *clkrst =
@@ -148,3 +806,156 @@ void reset_cmplx_set_enable(int cpu, int which, int reset)
 	else
 		writel(mask, &clkrst->crc_cpu_cmplx_clr);
 }
+
+unsigned clock_get_rate(enum clock_id clkid)
+{
+	struct clk_pll *pll;
+	u32 base;
+	u32 divm;
+	u64 parent_rate;
+	u64 rate;
+
+	parent_rate = osc_freq[clock_get_osc_freq()];
+	if (clkid == CLOCK_ID_OSC)
+		return parent_rate;
+
+	pll = get_pll(clkid);
+	base = readl(&pll->pll_base);
+
+	/* Oh for bf_unpack()... */
+	rate = parent_rate * ((base & PLL_DIVN_MASK) >> PLL_DIVN_SHIFT);
+	divm = (base & PLL_DIVM_MASK) >> PLL_DIVM_SHIFT;
+	if (clkid == CLOCK_ID_USB)
+		divm <<= (base & PLLU_VCO_FREQ_MASK) >> PLLU_VCO_FREQ_SHIFT;
+	else
+		divm <<= (base & PLL_DIVP_MASK) >> PLL_DIVP_SHIFT;
+	do_div(rate, divm);
+	return rate;
+}
+
+/**
+ * Set the output frequency you want for each PLL clock.
+ * PLL output frequencies are programmed by setting their N, M and P values.
+ * The governing equations are:
+ *     VCO = (Fi / m) * n, Fo = VCO / (2^p)
+ *     where Fo is the output frequency from the PLL.
+ * Example: Set the output frequency to 216Mhz(Fo) with 12Mhz OSC(Fi)
+ *     216Mhz = ((12Mhz / m) * n) / (2^p) so n=432,m=12,p=1
+ * Please see Tegra TRM section 5.3 to get the detail for PLL Programming
+ *
+ * @param n PLL feedback divider(DIVN)
+ * @param m PLL input divider(DIVN)
+ * @param p post divider(DIVP)
+ * @param cpcon base PLL charge pump(CPCON)
+ * @return 0 if ok, -1 on error (the requested PLL is incorrect and cannot
+ *		be overriden), 1 if PLL is already correct
+ */
+static int clock_set_rate(enum clock_id clkid, u32 n, u32 m, u32 p, u32 cpcon)
+{
+	u32 base_reg;
+	u32 misc_reg;
+	struct clk_pll *pll;
+
+	pll = get_pll(clkid);
+
+	base_reg = readl(&pll->pll_base);
+
+	/* Set BYPASS, m, n and p to PLL_BASE */
+	base_reg &= ~PLL_DIVM_MASK;
+	base_reg |= m << PLL_DIVM_SHIFT;
+
+	base_reg &= ~PLL_DIVN_MASK;
+	base_reg |= n << PLL_DIVN_SHIFT;
+
+	base_reg &= ~PLL_DIVP_MASK;
+	base_reg |= p << PLL_DIVP_SHIFT;
+
+	if (clkid == CLOCK_ID_PERIPH) {
+		/*
+		 * If the PLL is already set up, check that it is correct
+		 * and record this info for clock_verify() to check.
+		 */
+		if (base_reg & PLL_BASE_OVRRIDE_MASK) {
+			base_reg |= PLL_ENABLE_MASK;
+			if (base_reg != readl(&pll->pll_base))
+				pllp_valid = 0;
+			return pllp_valid ? 1 : -1;
+		}
+		base_reg |= PLL_BASE_OVRRIDE_MASK;
+	}
+
+	base_reg |= PLL_BYPASS_MASK;
+	writel(base_reg, &pll->pll_base);
+
+	/* Set cpcon to PLL_MISC */
+	misc_reg = readl(&pll->pll_misc);
+	misc_reg &= ~PLL_CPCON_MASK;
+	misc_reg |= cpcon << PLL_CPCON_SHIFT;
+	writel(misc_reg, &pll->pll_misc);
+
+	/* Enable PLL */
+	base_reg |= PLL_ENABLE_MASK;
+	writel(base_reg, &pll->pll_base);
+
+	/* Disable BYPASS */
+	base_reg &= ~PLL_BYPASS_MASK;
+	writel(base_reg, &pll->pll_base);
+
+	return 0;
+}
+
+int clock_verify(void)
+{
+	struct clk_pll *pll = get_pll(CLOCK_ID_PERIPH);
+	u32 reg = readl(&pll->pll_base);
+
+	if (!pllp_valid) {
+		printf("Warning: PLLP %x is not correct\n", reg);
+		return -1;
+	}
+	debug("PLLX %x is correct\n", reg);
+	return 0;
+}
+
+void clock_early_init(void)
+{
+	/*
+	 * PLLP output frequency set to 216MHz
+	 * PLLC output frequency set to 600Mhz
+	 *
+	 * TODO: Can we calculate these values instead of hard-coding?
+	 */
+	switch (clock_get_osc_freq()) {
+	case CLOCK_OSC_FREQ_12_0: /* OSC is 12Mhz */
+		clock_set_rate(CLOCK_ID_PERIPH, 432, 12, 1, 8);
+		clock_set_rate(CLOCK_ID_CGENERAL, 600, 12, 0, 8);
+		break;
+
+	case CLOCK_OSC_FREQ_26_0: /* OSC is 26Mhz */
+		clock_set_rate(CLOCK_ID_PERIPH, 432, 26, 1, 8);
+		clock_set_rate(CLOCK_ID_CGENERAL, 600, 26, 0, 8);
+		break;
+
+	case CLOCK_OSC_FREQ_13_0:
+	case CLOCK_OSC_FREQ_19_2:
+	default:
+		/*
+		 * These are not supported. It is too early to print a
+		 * message and the UART likely won't work anyway due to the
+		 * oscillator being wrong.
+		 */
+		break;
+	}
+}
+
+void clock_init(void)
+{
+	pll_rate[CLOCK_ID_MEMORY] = clock_get_rate(CLOCK_ID_MEMORY);
+	pll_rate[CLOCK_ID_PERIPH] = clock_get_rate(CLOCK_ID_PERIPH);
+	pll_rate[CLOCK_ID_CGENERAL] = clock_get_rate(CLOCK_ID_CGENERAL);
+	pll_rate[CLOCK_ID_OSC] = clock_get_rate(CLOCK_ID_OSC);
+	pll_rate[CLOCK_ID_SFROM32KHZ] = 32768;
+	debug("Osc = %d\n", pll_rate[CLOCK_ID_OSC]);
+	debug("PLLM = %d\n", pll_rate[CLOCK_ID_MEMORY]);
+	debug("PLLP = %d\n", pll_rate[CLOCK_ID_PERIPH]);
+}
diff --git a/arch/arm/include/asm/arch-tegra2/clk_rst.h b/arch/arm/include/asm/arch-tegra2/clk_rst.h
index bd9d9ade90..0b6e004fbc 100644
--- a/arch/arm/include/asm/arch-tegra2/clk_rst.h
+++ b/arch/arm/include/asm/arch-tegra2/clk_rst.h
@@ -43,9 +43,12 @@ struct clk_pll_simple {
  * structure for which we use clk_pll_simple. The reason for this non-
  * othogonal setup is not stated.
  */
-#define TEGRA_CLK_PLLS		6
-#define TEGRA_CLK_SIMPLE_PLLS	3	/* Number of simple PLLs */
-#define TEGRA_CLK_REGS		3	/* Number of clock enable registers */
+enum {
+	TEGRA_CLK_PLLS		= 6,	/* Number of normal PLLs */
+	TEGRA_CLK_SIMPLE_PLLS	= 3,	/* Number of simple PLLs */
+	TEGRA_CLK_REGS		= 3,	/* Number of clock enable registers */
+	TEGRA_CLK_SOURCES	= 64,	/* Number of peripheral clock sources */
+};
 
 /* Clock/Reset Controller (CLK_RST_CONTROLLER_) regs */
 struct clk_rst_ctlr {
@@ -79,65 +82,10 @@ struct clk_rst_ctlr {
 	uint crc_reserved10;		/* _reserved_10,	0xF8 */
 	uint crc_reserved11;		/* _reserved_11,	0xFC */
 
-	uint crc_clk_src_i2s1;		/*_I2S1_0,		0x100 */
-	uint crc_clk_src_i2s2;		/*_I2S2_0,		0x104 */
-	uint crc_clk_src_spdif_out;	/*_SPDIF_OUT_0,		0x108 */
-	uint crc_clk_src_spdif_in;	/*_SPDIF_IN_0,		0x10C */
-	uint crc_clk_src_pwm;		/*_PWM_0,		0x110 */
-	uint crc_clk_src_spi1;		/*_SPI1_0,		0x114 */
-	uint crc_clk_src_sbc2;		/*_SBC2_0,		0x118 */
-	uint crc_clk_src_sbc3;		/*_SBC3_0,		0x11C */
-	uint crc_clk_src_xio;		/*_XIO_0,		0x120 */
-	uint crc_clk_src_i2c1;		/*_I2C1_0,		0x124 */
-	uint crc_clk_src_dvc_i2c;	/*_DVC_I2C_0,		0x128 */
-	uint crc_clk_src_twc;		/*_TWC_0,		0x12C */
-	uint crc_reserved12;		/*			0x130 */
-	uint crc_clk_src_sbc1;		/*_SBC1_0,		0x134 */
-	uint crc_clk_src_disp1;		/*_DISP1_0,		0x138 */
-	uint crc_clk_src_disp2;		/*_DISP2_0,		0x13C */
-	uint crc_clk_src_cve;		/*_CVE_0,		0x140 */
-	uint crc_clk_src_ide;		/*_IDE_0,		0x144 */
-	uint crc_clk_src_vi;		/*_VI_0,		0x148 */
-	uint crc_reserved13;		/*			0x14C */
-	uint crc_clk_src_sdmmc1;	/*_SDMMC1_0,		0x150 */
-	uint crc_clk_src_sdmmc2;	/*_SDMMC2_0,		0x154 */
-	uint crc_clk_src_g3d;		/*_G3D_0,		0x158 */
-	uint crc_clk_src_g2d;		/*_G2D_0,		0x15C */
-	uint crc_clk_src_ndflash;	/*_NDFLASH_0,		0x160 */
-	uint crc_clk_src_sdmmc4;	/*_SDMMC4_0,		0x164 */
-	uint crc_clk_src_vfir;		/*_VFIR_0,		0x168 */
-	uint crc_clk_src_epp;		/*_EPP_0,		0x16C */
-	uint crc_clk_src_mp3;		/*_MPE_0,		0x170 */
-	uint crc_clk_src_mipi;		/*_MIPI_0,		0x174 */
-	uint crc_clk_src_uarta;		/*_UARTA_0,		0x178 */
-	uint crc_clk_src_uartb;		/*_UARTB_0,		0x17C */
-	uint crc_clk_src_host1x;	/*_HOST1X_0,		0x180 */
-	uint crc_reserved14;		/*			0x184 */
-	uint crc_clk_src_tvo;		/*_TVO_0,		0x188 */
-	uint crc_clk_src_hdmi;		/*_HDMI_0,		0x18C */
-	uint crc_reserved15;		/*			0x190 */
-	uint crc_clk_src_tvdac;		/*_TVDAC_0,		0x194 */
-	uint crc_clk_src_i2c2;		/*_I2C2_0,		0x198 */
-	uint crc_clk_src_emc;		/*_EMC_0,		0x19C */
-	uint crc_clk_src_uartc;		/*_UARTC_0,		0x1A0 */
-	uint crc_reserved16;		/*			0x1A4 */
-	uint crc_clk_src_vi_sensor;	/*_VI_SENSOR_0,		0x1A8 */
-	uint crc_reserved17;		/*			0x1AC */
-	uint crc_reserved18;		/*			0x1B0 */
-	uint crc_clk_src_sbc4;		/*_SBC4_0,		0x1B4 */
-	uint crc_clk_src_i2c3;		/*_I2C3_0,		0x1B8 */
-	uint crc_clk_src_sdmmc3;	/*_SDMMC3_0,		0x1BC */
-	uint crc_clk_src_uartd;		/*_UARTD_0,		0x1C0 */
-	uint crc_clk_src_uarte;		/*_UARTE_0,		0x1C4 */
-	uint crc_clk_src_vde;		/*_VDE_0,		0x1C8 */
-	uint crc_clk_src_owr;		/*_OWR_0,		0x1CC */
-	uint crc_clk_src_nor;		/*_NOR_0,		0x1D0 */
-	uint crc_clk_src_csite;		/*_CSITE_0,		0x1D4 */
-	uint crc_reserved19[9];		/*			0x1D8-1F8 */
-	uint crc_clk_src_osc;		/*_OSC_0,		0x1FC */
+	uint crc_clk_src[TEGRA_CLK_SOURCES]; /*_I2S1_0...	0x100-1fc */
 	uint crc_reserved20[80];	/*			0x200-33C */
-	uint crc_cpu_cmplx_set;		/* _CPU_CMPLX_SET_0,	0x340 */
-	uint crc_cpu_cmplx_clr;		/* _CPU_CMPLX_CLR_0,	0x344 */
+	uint crc_cpu_cmplx_set;		/* _CPU_CMPLX_SET_0,	0x340	  */
+	uint crc_cpu_cmplx_clr;		/* _CPU_CMPLX_CLR_0,	0x344     */
 };
 
 /* CLK_RST_CONTROLLER_CLK_CPU_CMPLX_0 */
@@ -156,10 +104,13 @@ struct clk_rst_ctlr {
 #define PLL_BASE_OVRRIDE_MASK	(1U << 28)
 
 #define PLL_DIVP_SHIFT		20
+#define PLL_DIVP_MASK		(7U << PLL_DIVP_SHIFT)
 
 #define PLL_DIVN_SHIFT		8
+#define PLL_DIVN_MASK		(0x3ffU << PLL_DIVN_SHIFT)
 
 #define PLL_DIVM_SHIFT		0
+#define PLL_DIVM_MASK		(0x1f << PLL_DIVM_SHIFT)
 
 /* CLK_RST_CONTROLLER_PLLx_MISC_0 */
 #define PLL_CPCON_SHIFT		8
@@ -168,9 +119,20 @@ struct clk_rst_ctlr {
 #define PLL_LFCON_SHIFT		4
 
 #define PLLU_VCO_FREQ_SHIFT	20
+#define PLLU_VCO_FREQ_MASK	(1U << PLLU_VCO_FREQ_SHIFT)
 
 /* CLK_RST_CONTROLLER_OSC_CTRL_0 */
 #define OSC_FREQ_SHIFT		30
 #define OSC_FREQ_MASK		(3U << OSC_FREQ_SHIFT)
 
+/* CLK_RST_CONTROLLER_CLK_SOURCE_x_OUT_0 */
+#define OUT_CLK_DIVISOR_SHIFT	0
+#define OUT_CLK_DIVISOR_MASK	(255 << OUT_CLK_DIVISOR_SHIFT)
+
+#define OUT_CLK_SOURCE_SHIFT	30
+#define OUT_CLK_SOURCE_MASK	(3U << OUT_CLK_SOURCE_SHIFT)
+
+#define OUT_CLK_SOURCE4_SHIFT	28
+#define OUT_CLK_SOURCE4_MASK	(15U << OUT_CLK_SOURCE4_SHIFT)
+
 #endif	/* CLK_RST_H */
diff --git a/arch/arm/include/asm/arch-tegra2/clock.h b/arch/arm/include/asm/arch-tegra2/clock.h
index 8adb23c8ac..49e9904b57 100644
--- a/arch/arm/include/asm/arch-tegra2/clock.h
+++ b/arch/arm/include/asm/arch-tegra2/clock.h
@@ -51,7 +51,12 @@ enum clock_id {
 	CLOCK_ID_EPCI,
 	CLOCK_ID_SFROM32KHZ,
 
-	CLOCK_ID_COUNT,
+	/* These are the base clocks (inputs to the Tegra SOC) */
+	CLOCK_ID_32KHZ,
+	CLOCK_ID_OSC,
+
+	CLOCK_ID_COUNT,	/* number of clocks */
+	CLOCK_ID_NONE = -1,
 };
 
 /* The clocks supported by the hardware */
@@ -183,10 +188,6 @@ enum periph_id {
 /* return 1 if a PLL ID is in range */
 #define clock_id_isvalid(id) ((id) >= CLOCK_ID_FIRST && (id) < CLOCK_ID_COUNT)
 
-/* return 1 if a peripheral ID is in range */
-#define clock_periph_id_isvalid(id) ((id) >= PERIPH_ID_FIRST && \
-		(id) < PERIPH_ID_COUNT)
-
 /* PLL stabilization delay in usec */
 #define CLOCK_PLL_STABLE_DELAY_US 300
 
@@ -216,6 +217,13 @@ unsigned long clock_start_pll(enum clock_id id, u32 divm, u32 divn,
 void clock_enable(enum periph_id clkid);
 
 /*
+ * Disable a clock
+ *
+ * @param id	clock id
+ */
+void clock_disable(enum periph_id clkid);
+
+/*
  * Set whether a clock is enabled or disabled.
  *
  * @param id		clock id
@@ -259,4 +267,94 @@ enum crc_reset_id {
  */
 void reset_cmplx_set_enable(int cpu, int which, int reset);
 
+/**
+ * Set the source for a peripheral clock. This plus the divisor sets the
+ * clock rate. You need to look up the datasheet to see the meaning of the
+ * source parameter as it changes for each peripheral.
+ *
+ * Warning: This function is only for use pre-relocation. Please use
+ * clock_start_periph_pll() instead.
+ *
+ * @param periph_id	peripheral to adjust
+ * @param source	source clock (0, 1, 2 or 3)
+ */
+void clock_ll_set_source(enum periph_id periph_id, unsigned source);
+
+/**
+ * Set the source and divisor for a peripheral clock. This sets the
+ * clock rate. You need to look up the datasheet to see the meaning of the
+ * source parameter as it changes for each peripheral.
+ *
+ * Warning: This function is only for use pre-relocation. Please use
+ * clock_start_periph_pll() instead.
+ *
+ * @param periph_id	peripheral to adjust
+ * @param source	source clock (0, 1, 2 or 3)
+ * @param divisor	divisor value to use
+ */
+void clock_ll_set_source_divisor(enum periph_id periph_id, unsigned source,
+		unsigned divisor);
+
+/**
+ * Start a peripheral PLL clock at the given rate. This also resets the
+ * peripheral.
+ *
+ * @param periph_id	peripheral to start
+ * @param parent	PLL id of required parent clock
+ * @param rate		Required clock rate in Hz
+ * @return rate selected in Hz, or -1U if something went wrong
+ */
+unsigned clock_start_periph_pll(enum periph_id periph_id,
+		enum clock_id parent, unsigned rate);
+
+/**
+ * Returns the rate of a peripheral clock in Hz. Since the caller almost
+ * certainly knows the parent clock (having just set it) we require that
+ * this be passed in so we don't need to work it out.
+ *
+ * @param periph_id	peripheral to start
+ * @param parent	PLL id of parent clock (used to calculate rate, you
+ *			must know this!)
+ * @return clock rate of peripheral in Hz
+ */
+unsigned long clock_get_periph_rate(enum periph_id periph_id,
+		enum clock_id parent);
+
+/**
+ * Adjust peripheral PLL clock to the given rate. This does not reset the
+ * peripheral. If a second stage divisor is not available, pass NULL for
+ * extra_div. If it is available, then this parameter will return the
+ * divisor selected (which will be a power of 2 from 1 to 256).
+ *
+ * @param periph_id	peripheral to start
+ * @param parent	PLL id of required parent clock
+ * @param rate		Required clock rate in Hz
+ * @param extra_div	value for the second-stage divisor (NULL if one is
+			not available)
+ * @return rate selected in Hz, or -1U if something went wrong
+ */
+unsigned clock_adjust_periph_pll_div(enum periph_id periph_id,
+		enum clock_id parent, unsigned rate, int *extra_div);
+
+/**
+ * Returns the clock rate of a specified clock, in Hz.
+ *
+ * @param parent	PLL id of clock to check
+ * @return rate of clock in Hz
+ */
+unsigned clock_get_rate(enum clock_id clkid);
+
+/*
+ * Checks that clocks are valid and prints a warning if not
+ *
+ * @return 0 if ok, -1 on error
+ */
+int clock_verify(void);
+
+/* Initialize the clocks */
+void clock_init(void);
+
+/* Initialize the PLLs */
+void clock_early_init(void);
+
 #endif