mips: rename mach-mt7620 to mach-mtmips

Currently mach-mt7620 contains only support for mt7628. To avoid confusion,
rename mach-mt7620 to mach-mtmips, which means MediaTek MIPS platforms.
MT7620 and MT7628 should be distinguished by SOC_MT7620 and SOC_MT7628
because they do not share the same lowlevel codes.

Dependencies of four drivers are changed to SOC_MT7628 as these drivers
are only used by MT7628.

Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>

1 files changed, 85 insertions, 0 deletions

diff --git a/arch/mips/mach-mtmips/cpu.c b/arch/mips/mach-mtmips/cpu.c
new file mode 100644
index 0000000000..fcd0484a6d
--- /dev/null
+++ b/arch/mips/mach-mtmips/cpu.c
@@ -0,0 +1,85 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2018 Stefan Roese <sr@denx.de>
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <ram.h>
+#include <wdt.h>
+#include <asm/io.h>
+#include <linux/io.h>
+#include <linux/sizes.h>
+#include "mt76xx.h"
+
+#define STR_LEN			6
+
+#ifdef CONFIG_BOOT_ROM
+int mach_cpu_init(void)
+{
+	ddr_calibrate();
+
+	return 0;
+}
+#endif
+
+int dram_init(void)
+{
+	gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE, SZ_256M);
+
+	return 0;
+}
+
+int print_cpuinfo(void)
+{
+	static const char * const boot_str[] = { "PLL (3-Byte SPI Addr)",
+						 "PLL (4-Byte SPI Addr)",
+						 "XTAL (3-Byte SPI Addr)",
+						 "XTAL (4-Byte SPI Addr)" };
+	const void *blob = gd->fdt_blob;
+	void __iomem *sysc_base;
+	char buf[STR_LEN + 1];
+	fdt_addr_t base;
+	fdt_size_t size;
+	char *str;
+	int node;
+	u32 val;
+
+	/* Get system controller base address */
+	node = fdt_node_offset_by_compatible(blob, -1, "ralink,mt7620a-sysc");
+	if (node < 0)
+		return -FDT_ERR_NOTFOUND;
+
+	base = fdtdec_get_addr_size_auto_noparent(blob, node, "reg",
+						  0, &size, true);
+	if (base == FDT_ADDR_T_NONE)
+		return -EINVAL;
+
+	sysc_base = ioremap_nocache(base, size);
+
+	str = (char *)sysc_base + MT76XX_CHIPID_OFFS;
+	snprintf(buf, STR_LEN + 1, "%s", str);
+	val = readl(sysc_base + MT76XX_CHIP_REV_ID_OFFS);
+	printf("CPU:   %-*s Rev %ld.%ld - ", STR_LEN, buf,
+	       (val & GENMASK(11, 8)) >> 8, val & GENMASK(3, 0));
+
+	val = (readl(sysc_base + MT76XX_SYSCFG0_OFFS) & GENMASK(3, 1)) >> 1;
+	printf("Boot from %s\n", boot_str[val]);
+
+	return 0;
+}
+
+int arch_misc_init(void)
+{
+	/*
+	 * It has been noticed, that sometimes the d-cache is not in a
+	 * "clean-state" when U-Boot is running on MT7688. This was
+	 * detected when using the ethernet driver (which uses d-cache)
+	 * and a TFTP command does not complete. Flushing the complete
+	 * d-cache (again?) here seems to fix this issue.
+	 */
+	flush_dcache_range(gd->bd->bi_memstart,
+			   gd->bd->bi_memstart + gd->ram_size - 1);
+
+	return 0;
+}