ppc: Move cpu/$CPU to arch/ppc/cpu/$CPU

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>

1 files changed, 311 insertions, 0 deletions

diff --git a/arch/ppc/cpu/mpc85xx/release.S b/arch/ppc/cpu/mpc85xx/release.S
new file mode 100644
index 0000000000..0b5b9da032
--- /dev/null
+++ b/arch/ppc/cpu/mpc85xx/release.S
@@ -0,0 +1,311 @@
+/*
+ * Copyright 2008-2010 Freescale Semiconductor, Inc.
+ * Kumar Gala <kumar.gala@freescale.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <config.h>
+#include <mpc85xx.h>
+#include <version.h>
+
+#define _LINUX_CONFIG_H 1	/* avoid reading Linux autoconf.h file	*/
+
+#include <ppc_asm.tmpl>
+#include <ppc_defs.h>
+
+#include <asm/cache.h>
+#include <asm/mmu.h>
+
+/* To boot secondary cpus, we need a place for them to start up.
+ * Normally, they start at 0xfffffffc, but that's usually the
+ * firmware, and we don't want to have to run the firmware again.
+ * Instead, the primary cpu will set the BPTR to point here to
+ * this page.  We then set up the core, and head to
+ * start_secondary.  Note that this means that the code below
+ * must never exceed 1023 instructions (the branch at the end
+ * would then be the 1024th).
+ */
+	.globl	__secondary_start_page
+	.align	12
+__secondary_start_page:
+/* First do some preliminary setup */
+	lis	r3, HID0_EMCP@h		/* enable machine check */
+#ifndef CONFIG_E500MC
+	ori	r3,r3,HID0_TBEN@l	/* enable Timebase */
+#endif
+#ifdef CONFIG_PHYS_64BIT
+	ori	r3,r3,HID0_ENMAS7@l	/* enable MAS7 updates */
+#endif
+	mtspr	SPRN_HID0,r3
+
+#ifndef CONFIG_E500MC
+	li	r3,(HID1_ASTME|HID1_ABE)@l	/* Addr streaming & broadcast */
+	mfspr   r0,PVR
+	andi.	r0,r0,0xff
+	cmpwi	r0,0x50@l	/* if we are rev 5.0 or greater set MBDD */
+	blt 1f
+	/* Set MBDD bit also */
+	ori r3, r3, HID1_MBDD@l
+1:
+	mtspr	SPRN_HID1,r3
+#endif
+
+	/* Enable branch prediction */
+	lis	r3,BUCSR_ENABLE@h
+	ori	r3,r3,BUCSR_ENABLE@l
+	mtspr	SPRN_BUCSR,r3
+
+	/* Ensure TB is 0 */
+	li	r3,0
+	mttbl	r3
+	mttbu	r3
+
+	/* Enable/invalidate the I-Cache */
+	lis	r2,(L1CSR1_ICFI|L1CSR1_ICLFR)@h
+	ori	r2,r2,(L1CSR1_ICFI|L1CSR1_ICLFR)@l
+	mtspr	SPRN_L1CSR1,r2
+1:
+	mfspr	r3,SPRN_L1CSR1
+	and.	r1,r3,r2
+	bne	1b
+
+	lis	r3,(L1CSR1_CPE|L1CSR1_ICE)@h
+	ori	r3,r3,(L1CSR1_CPE|L1CSR1_ICE)@l
+	mtspr	SPRN_L1CSR1,r3
+	isync
+2:
+	mfspr	r3,SPRN_L1CSR1
+	andi.	r1,r3,L1CSR1_ICE@l
+	beq	2b
+
+	/* Enable/invalidate the D-Cache */
+	lis	r2,(L1CSR0_DCFI|L1CSR0_DCLFR)@h
+	ori	r2,r2,(L1CSR0_DCFI|L1CSR0_DCLFR)@l
+	mtspr	SPRN_L1CSR0,r2
+1:
+	mfspr	r3,SPRN_L1CSR0
+	and.	r1,r3,r2
+	bne	1b
+
+	lis	r3,(L1CSR0_CPE|L1CSR0_DCE)@h
+	ori	r3,r3,(L1CSR0_CPE|L1CSR0_DCE)@l
+	mtspr	SPRN_L1CSR0,r3
+	isync
+2:
+	mfspr	r3,SPRN_L1CSR0
+	andi.	r1,r3,L1CSR0_DCE@l
+	beq	2b
+
+#define toreset(x) (x - __secondary_start_page + 0xfffff000)
+
+	/* get our PIR to figure out our table entry */
+	lis	r3,toreset(__spin_table)@h
+	ori	r3,r3,toreset(__spin_table)@l
+
+	/* r10 has the base address for the entry */
+	mfspr	r0,SPRN_PIR
+#ifdef CONFIG_E500MC
+	rlwinm	r4,r0,27,27,31
+#else
+	mr	r4,r0
+#endif
+	slwi	r8,r4,5
+	add	r10,r3,r8
+
+#if defined(CONFIG_E500MC) && defined(CONFIG_SYS_CACHE_STASHING)
+	/* set stash id to (coreID) * 2 + 32 + L1 CT (0) */
+	slwi	r8,r4,1
+	addi	r8,r8,32
+	mtspr	L1CSR2,r8
+#endif
+
+#ifdef CONFIG_BACKSIDE_L2_CACHE
+	/* Enable/invalidate the L2 cache */
+	msync
+	lis	r2,(L2CSR0_L2FI|L2CSR0_L2LFC)@h
+	ori	r2,r2,(L2CSR0_L2FI|L2CSR0_L2LFC)@l
+	mtspr	SPRN_L2CSR0,r2
+1:
+	mfspr	r3,SPRN_L2CSR0
+	and.	r1,r3,r2
+	bne	1b
+
+#ifdef CONFIG_SYS_CACHE_STASHING
+	/* set stash id to (coreID) * 2 + 32 + L2 (1) */
+	addi	r3,r8,1
+	mtspr	SPRN_L2CSR1,r3
+#endif
+
+	lis	r3,CONFIG_SYS_INIT_L2CSR0@h
+	ori	r3,r3,CONFIG_SYS_INIT_L2CSR0@l
+	mtspr	SPRN_L2CSR0,r3
+	isync
+2:
+	mfspr	r3,SPRN_L2CSR0
+	andis.	r1,r3,L2CSR0_L2E@h
+	beq	2b
+#endif
+
+#define EPAPR_MAGIC		(0x45504150)
+#define ENTRY_ADDR_UPPER	0
+#define ENTRY_ADDR_LOWER	4
+#define ENTRY_R3_UPPER		8
+#define ENTRY_R3_LOWER		12
+#define ENTRY_RESV		16
+#define ENTRY_PIR		20
+#define ENTRY_R6_UPPER		24
+#define ENTRY_R6_LOWER		28
+#define ENTRY_SIZE		32
+
+	/* setup the entry */
+	li	r3,0
+	li	r8,1
+	stw	r0,ENTRY_PIR(r10)
+	stw	r3,ENTRY_ADDR_UPPER(r10)
+	stw	r8,ENTRY_ADDR_LOWER(r10)
+	stw	r3,ENTRY_R3_UPPER(r10)
+	stw	r4,ENTRY_R3_LOWER(r10)
+	stw	r3,ENTRY_R6_UPPER(r10)
+	stw	r3,ENTRY_R6_LOWER(r10)
+
+	/* load r13 with the address of the 'bootpg' in SDRAM */
+	lis	r13,toreset(__bootpg_addr)@h
+	ori	r13,r13,toreset(__bootpg_addr)@l
+	lwz	r13,0(r13)
+
+	/* setup mapping for AS = 1, and jump there */
+	lis	r11,(MAS0_TLBSEL(1)|MAS0_ESEL(1))@h
+	mtspr	SPRN_MAS0,r11
+	lis	r11,(MAS1_VALID|MAS1_IPROT)@h
+	ori	r11,r11,(MAS1_TS|MAS1_TSIZE(BOOKE_PAGESZ_4K))@l
+	mtspr	SPRN_MAS1,r11
+	oris	r11,r13,(MAS2_I|MAS2_G)@h
+	ori	r11,r13,(MAS2_I|MAS2_G)@l
+	mtspr	SPRN_MAS2,r11
+	oris	r11,r13,(MAS3_SX|MAS3_SW|MAS3_SR)@h
+	ori	r11,r13,(MAS3_SX|MAS3_SW|MAS3_SR)@l
+	mtspr	SPRN_MAS3,r11
+	tlbwe
+
+	bl	1f
+1:	mflr	r11
+	/*
+	 * OR in 0xfff to create a mask of the bootpg SDRAM address.  We use
+	 * this mask to fixup the cpu spin table and the address that we want
+	 * to jump to, eg change them from 0xfffffxxx to 0x7ffffxxx if the
+	 * bootpg is at 0x7ffff000 in SDRAM.
+	 */
+	ori	r13,r13,0xfff
+	and	r11, r11, r13
+	and	r10, r10, r13
+
+	addi	r11,r11,(2f-1b)
+	mfmsr	r13
+	ori	r12,r13,MSR_IS|MSR_DS@l
+
+	mtspr	SPRN_SRR0,r11
+	mtspr	SPRN_SRR1,r12
+	rfi
+
+	/* spin waiting for addr */
+2:
+	lwz	r4,ENTRY_ADDR_LOWER(r10)
+	andi.	r11,r4,1
+	bne	2b
+	isync
+
+	/* setup IVORs to match fixed offsets */
+#include "fixed_ivor.S"
+
+	/* get the upper bits of the addr */
+	lwz	r11,ENTRY_ADDR_UPPER(r10)
+
+	/* setup branch addr */
+	mtspr	SPRN_SRR0,r4
+
+	/* mark the entry as released */
+	li	r8,3
+	stw	r8,ENTRY_ADDR_LOWER(r10)
+
+	/* mask by ~64M to setup our tlb we will jump to */
+	rlwinm	r12,r4,0,0,5
+
+	/* setup r3, r4, r5, r6, r7, r8, r9 */
+	lwz	r3,ENTRY_R3_LOWER(r10)
+	li	r4,0
+	li	r5,0
+	lwz	r6,ENTRY_R6_LOWER(r10)
+	lis	r7,(64*1024*1024)@h
+	li	r8,0
+	li	r9,0
+
+	/* load up the pir */
+	lwz	r0,ENTRY_PIR(r10)
+	mtspr	SPRN_PIR,r0
+	mfspr	r0,SPRN_PIR
+	stw	r0,ENTRY_PIR(r10)
+
+	mtspr	IVPR,r12
+/*
+ * Coming here, we know the cpu has one TLB mapping in TLB1[0]
+ * which maps 0xfffff000-0xffffffff one-to-one.  We set up a
+ * second mapping that maps addr 1:1 for 64M, and then we jump to
+ * addr
+ */
+	lis	r10,(MAS0_TLBSEL(1)|MAS0_ESEL(0))@h
+	mtspr	SPRN_MAS0,r10
+	lis	r10,(MAS1_VALID|MAS1_IPROT)@h
+	ori	r10,r10,(MAS1_TSIZE(BOOKE_PAGESZ_64M))@l
+	mtspr	SPRN_MAS1,r10
+	/* WIMGE = 0b00000 for now */
+	mtspr	SPRN_MAS2,r12
+	ori	r12,r12,(MAS3_SX|MAS3_SW|MAS3_SR)
+	mtspr	SPRN_MAS3,r12
+#ifdef CONFIG_ENABLE_36BIT_PHYS
+	mtspr	SPRN_MAS7,r11
+#endif
+	tlbwe
+
+/* Now we have another mapping for this page, so we jump to that
+ * mapping
+ */
+	mtspr	SPRN_SRR1,r13
+	rfi
+
+	/*
+	 * Allocate some space for the SDRAM address of the bootpg.
+	 * This variable has to be in the boot page so that it can
+	 * be accessed by secondary cores when they come out of reset.
+	 */
+	.globl __bootpg_addr
+__bootpg_addr:
+	.long	0
+
+	.align L1_CACHE_SHIFT
+	.globl __spin_table
+__spin_table:
+	.space CONFIG_MAX_CPUS*ENTRY_SIZE
+
+	/* Fill in the empty space.  The actual reset vector is
+	 * the last word of the page */
+__secondary_start_code_end:
+	.space 4092 - (__secondary_start_code_end - __secondary_start_page)
+__secondary_reset_vector:
+	b	__secondary_start_page